ATSAMC20G15A-MUT - 48MHz Cortex-M0+ MCU 32KB Flash | Microchip
MPN: ATSAMC20G15A-MUT ✓ Hoạt độngATSAMC20G15A-MUT Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a wide range of peripherals such as timers, communication interfaces, ADCs, and GPIO onto a single silicon die. Within the broader taxonomy of semiconductors, MCUs sit under microcontrollers -> microprocessors and controllers -> integrated circuits (ICs). The Cortex-M0+ core from Arm is the smallest and most energy-efficient member of the Cortex-M family, optimized for low-cost, low-power embedded applications while still providing a 32-bit instruction set, single-cycle hardware multiplier, and deterministic interrupt handling.
Key features of the ATSAMC20G15A-MUT include a Cortex-M0+ core with Micro Trace Buffer and Memory Protection Unit (MPU), 1 KB of independent self-programmable Flash for EEPROM emulation, a 12-bit 1 Msps ADC with up to 16 channels and hardware oversampling, two analog comparators with window-compare, a 16-bit Sigma-Delta DAC, and an integrated temperature sensor. It also provides a Peripheral Touch Controller (PTC) supporting up to 256 channels of capacitive touch and proximity sensing, six SERCOM modules configurable as UART/SPI/I2C, and up to 38 programmable I/O pins. An integrated CAN-FD controller rounds out the connectivity for automotive and industrial networking.
Architecturally, the SAM C20 family shares a common peripheral set with the SAM D20/D21 families, allowing firmware and toolchain reuse. The 5 V-tolerant GPIO and supply simplify interfacing to legacy 5 V sensors and actuators, eliminating the level shifters required by 3.3 V-only MCUs. The on-chip voltage regulator, brown-out detector, and Watchdog Timer with Window mode enhance reliability in harsh industrial environments.
Typical applications include automotive body and chassis controllers, industrial sensor nodes, capacitive touch user interfaces, motor control peripherals, building automation, and CAN-FD networked equipment. The wide 2.7 V to 5.5 V supply range and AEC-Q100 Grade 1 qualification make it especially suited to 12 V/24 V vehicle systems and 24 V industrial bus rails.
When designing with this part, remember that the QFN package requires a thermal pad soldered to a ground copper pour for proper heat dissipation and electrical grounding. The supply pins should be decoupled with 100 nF ceramic capacitors placed as close to each VDD pin as possible, plus a bulk 4.7 uF to 10 uF capacitor near the regulator input.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found on individual distributor listings or the manufacturer datasheet, helping engineers compare the ATSAMC20G15A-MUT against pin-compatible options quickly.
Bộ thay thế dễ dàng lắp đặt cho ATSAMC20G15A-MUT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATSAMC20G15A-MUT (cùng hình factor và footprint) — khác nhau ở Package, ADC, Operating Temperature, Flash Memory, DAC.
ATSAMC20E15A-MUT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMC20G16A-MUT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAMC20G17A-MUT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMD20G15A-MUT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMC20E16A-MNT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMC20E18A-MUT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMC20G15A-MUT Tỷ lệ tối đa & tính chất điện
| Manufacturer | Microchip Technology (formerly Atmel) |
| Series | SAM C20 |
| Core | ARM Cortex-M0+ |
| Core Size | 32-Bit |
| Maximum CPU Clock | 48 MHz |
| Program Memory (Flash) | 32 KB (32K x 8) |
| EEPROM Emulation Flash | 1 KB (independent self-programmable) |
| RAM | 4 KB |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Khoảng nhiệt độ hoạt động | -40C to +85C (industrial) |
| AEC-Q100 Grade | Grade 1 |
| Hộp | 48-QFN (7x7 mm) |
| Kiểu lắp đặt | Surface Mount |
| I/O Pins | Up to 38 programmable |
| ADC | 12-bit, up to 16 channels, 1 Msps with hardware oversampling |
| DAC | 16-bit Sigma-Delta, 1 channel |
| Analog Comparators | 2 (with window compare) |
| PTC (Touch Controller) | Up to 256 channels capacitive touch / proximity |
| SERCOM Modules | 6 (configurable UART/SPI/I2C) |
| CAN-FD Controller | 1 |
| Temperature Sensor | Integrated |
| Trạng thái RoHS | Compliant |
Cấu hình chân ATSAMC20G15A-MUT
| Chân 1 | VDDIO — Digital I/O supply voltage |
| Chân 2 | PA02 — GPIO / ADC AIN[0] |
| Chân 3 | PA03 — GPIO / ADC AIN[1] / VREFA |
| Chân 4 | GND — Ground |
| Chân 5 | PA04 — GPIO / ADC AIN[4] / VREFB |
| Chân 6 | PA05 — GPIO / ADC AIN[5] |
| Chân 7 | PA06 — GPIO / ADC AIN[6] |
| Chân 8 | PA07 — GPIO / ADC AIN[7] |
| Chân 9 | PA08 — GPIO / SERCOM0 PAD[0] |
| Chân 10 | PA09 — GPIO / SERCOM0 PAD[1] |
| Chân 11 | PA10 — GPIO / SERCOM0 PAD[2] |
| Chân 12 | PA11 — GPIO / SERCOM0 PAD[3] |
| Chân 13 | VDD — Core supply voltage |
| Chân 14 | GND — Ground |
| Chân 15 | PA14 — GPIO / XIN |
| Chân 16 | PA15 — GPIO / XOUT |
| Chân 17 | PA16 — GPIO / SERCOM1 PAD[0] |
| Chân 18 | PA17 — GPIO / SERCOM1 PAD[1] |
| Chân 19 | PA18 — GPIO / SERCOM1 PAD[2] |
| Chân 20 | PA19 — GPIO / SERCOM1 PAD[3] |
| Chân 21 | PA20 — GPIO / SERCOM3 PAD[0] |
| Chân 22 | PA21 — GPIO / SERCOM3 PAD[1] |
| Chân 23 | PA22 — GPIO / SERCOM2 PAD[0] |
| Chân 24 | PA23 — GPIO / SERCOM2 PAD[1] |
| Chân 25 | PA24 — GPIO / SERCOM2 PAD[2] / CAN RX |
| Chân 26 | PA25 — GPIO / SERCOM2 PAD[3] / CAN TX |
| Chân 27 | GND — Ground |
| Chân 28 | VDD — Core supply voltage |
| Chân 29 | PB02 — GPIO / ADC AIN[10] |
| Chân 30 | PB03 — GPIO / ADC AIN[11] |
| Chân 31 | PB04 — GPIO / ADC AIN[12] |
| Chân 32 | PB05 — GPIO / ADC AIN[13] |
| Chân 33 | PB06 — GPIO / ADC AIN[14] |
| Chân 34 | PB07 — GPIO / ADC AIN[15] |
| Chân 35 | PB08 — GPIO / SERCOM4 PAD[0] |
| Chân 36 | PB09 — GPIO / SERCOM4 PAD[1] |
| Chân 37 | PB10 — GPIO / SERCOM4 PAD[2] |
| Chân 38 | PB11 — GPIO / SERCOM4 PAD[3] |
| Chân 39 | PB12 — GPIO / SERCOM5 PAD[0] |
| Chân 40 | PB13 — GPIO / SERCOM5 PAD[1] |
| Chân 41 | PB14 — GPIO / SERCOM5 PAD[2] |
| Chân 42 | PB15 — GPIO / SERCOM5 PAD[3] |
| Chân 43 | PB16 — GPIO / SERCOM5 PAD[0] alt |
| Chân 44 | PB17 — GPIO / SERCOM5 PAD[1] alt |
| Chân 45 | RESETN — Reset input (active low) |
| Chân 46 | SWDIO — Serial Wire Debug I/O |
| Chân 47 | SWCLK — Serial Wire Debug Clock |
| Chân 48 | GND — Thermal pad / Ground (must be soldered to PCB ground pour) |
Ứng dụng tiêu biểu
ATSAMC20G15A-MUT phù hợp cho 6 Áp dụngs: Automotive Body and Chassis Controllers, Capacitive Touch User Interfaces, Industrial Sensor Nodes and 24V Bus Systems, Building Automation and HVAC Controls, Small BLDC and Stepper Motor Control, Smart Home and IoT Edge Nodes.
Automotive Body and Chassis Controllers
The ATSAMC20G15A-MUT's AEC-Q100 Grade 1 qualification and integrated CAN-FD controller make it a strong fit for 12 V/24 V automotive body electronics such as seat controllers, door modules, mirror adjusters, and lighting drivers. Its 5 V-tolerant GPIO directly interfaces 5 V sensors and actuators without external level shifters, simplifying BOM and PCB layout. The 48 MHz Cortex-M0+ core, plus 6 SERCOM channels, easily handles CAN-FD message processing alongside LIN master/slave stacks. According to Microchip, the SAM C20 family is designed for industrial and commercial applications in noisy environments, supporting engine-bay-adjacent ECUs operating from 2.7 V to 5.5 V with onboard brown-out detection and watchdog.
Được đề xuất
Capacitive Touch User Interfaces
The ATSAMC20G15A-MUT integrates a Peripheral Touch Controller (PTC) supporting up to 256 channels of capacitive touch and proximity sensing with driven shield for water-tolerant operation. Combined with the 12-bit ADC oversampling to 16 bits and the 48 MHz core, it can scan large touch panels and run the touch-state machine deterministically. The 5 V supply allows direct drive of LED backlights and haptic feedback actuators alongside the touch matrix. AEC-Q100 Grade 1 qualification also opens it up to in-cabin automotive HMI applications such as climate-control panels and overhead consoles.
Được đề xuất
Industrial Sensor Nodes and 24V Bus Systems
The ATSAMC20G15A-MUT's 2.7 V to 5.5 V supply range is well-matched to 24 V industrial bus rails after an external wide-Vin DC-DC step-down, and its 5 V GPIO simplifies interfacing to legacy industrial sensors. The Cortex-M0+ core delivers deterministic interrupt latency for time-critical control loops, while 32 KB Flash and 4 KB SRAM hold small protocol stacks such as IO-Link, Modbus RTU, or CANopen. The 12-bit 1 Msps ADC with hardware oversampling enables precise sensor measurements, and the integrated temperature sensor supports self-monitoring for predictive maintenance in factory automation.
Được đề xuất
Building Automation and HVAC Controls
The ATSAMC20G15A-MUT is well-suited to building automation endpoints such as smart thermostats, VAV damper actuators, and lighting controllers, thanks to its 5 V tolerance, 38 GPIO, and CAN-FD connectivity. The 12-bit ADC plus two analog comparators with window compare mode simplify direct connection of thermistors and 0-10 V analog sensors common in HVAC. AEC-Q100 Grade 1 qualification and -40C to +85C industrial temperature range support installation in mechanical rooms and outdoor enclosures. The 48 MHz Cortex-M0+ also handles wireless co-processor command translation for sub-GHz or BLE modules.
Được đề xuất
Small BLDC and Stepper Motor Control
The ATSAMC20G15A-MUT's 48 MHz Cortex-M0+ core, six SERCOM modules, and 16-bit Sigma-Delta DAC make it a viable host for small brushless DC or stepper motor control boards, especially in 5 V systems. Hardware PWM timers support complementary outputs with dead-time insertion for half-bridge drives, and the integrated analog comparators enable fast overcurrent protection. AEC-Q100 Grade 1 extends usability to automotive pump and fan controllers. The 4 KB SRAM supports basic field-oriented-control (FOC) libraries for low-pole-count BLDCs used in fans and small pumps.
Được đề xuất
Smart Home and IoT Edge Nodes
The ATSAMC20G15A-MUT combines low power, 5 V tolerance, and CAN-FD to act as a wired edge node in smart-home and IoT systems, where it can aggregate sensor data from multiple SPI/UART/I2C peripherals. The 32 KB Flash accommodates TLS-lite stacks or Matter-over-Thread bridge logic, and the 4 KB SRAM is enough for buffering telemetry before forwarding over Wi-Fi or BLE companion modules. Its AEC-Q100 qualification also allows automotive cabin IoT use cases such as OBD-II telemetry dongles and vehicle accessory controllers.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATSAMC20G15A-MUT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATSAMC20E15A-MUT | ATSAMC20G16A-MUT | ATSAMC20G17A-MUT | ATSAMD20G15A-MUT | ATSAMC20E16A-MNT | ATSAMC20E18A-MUT |
|---|---|---|---|---|---|---|---|
| Package | 48-QFN (7x7 mm) | 48-QFN (7x7 mm) - same | 48-QFN (7x7 mm) - same | 48-QFN (7x7 mm) - same | 48-QFN (7x7 mm) - same | 48-QFN (7x7 mm) - same | 48-QFN (7x7 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash | 32 KB | 32 KB | 64 KB | 128 KB | 32 KB | 64 KB | 256 KB |
| SRAM | 4 KB | 4 KB | 8 KB | 16 KB | 4 KB | 8 KB | 32 KB |
| CAN-FD | Yes | No | Yes | Yes | No | No | No |
| Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 1.62 V to 3.6 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Maximum Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| AEC-Q100 | Grade 1 | Grade 1 | Grade 1 | Grade 1 | Not qualified (3.3 V family) | Grade 1 | Grade 1 |
Bảo phân biệt quan trọng
- Integrated CAN-FD plus 5 V-tolerant I/O in 48-QFN (vsATSAMC20E15A-MUT)
- Pin-compatible upgrade path to 64 KB / 128 KB / 256 KB Flash (vsATSAMC20G16A-MUT)
- 5 V I/O tolerance and AEC-Q100 Grade 1 in same package as 3.3 V SAMD20 (vsATSAMD20G15A-MUT)
Ghi chú thiết kế
Estimated: at 48 MHz active and typical 5 V I/O toggling, the ATSAMC20G15A-MUT consumes roughly 7-9 mA, dissipating approximately 35-45 mW. The 48-QFN package's thermal pad MUST be soldered to a continuous PCB ground pour of at least 25 mm^2 to keep theta_JA below 40 C/W. Without thermal pad soldering, junction temperature can rise 30-40 C above ambient in sealed automotive enclosures, potentially triggering thermal shutdown during sustained PTC scanning or CAN-FD bursts.
Place a 100 nF X7R 0402/0603 ceramic decoupling capacitor within 2 mm of every VDD and VDDIO pin pair, and add a bulk 4.7 uF X5R ceramic near the regulator input. According to the SAM C20 datasheet layout guidelines, the exposed thermal pad requires at least 8 thermal vias (0.3 mm drill, 0.5 mm pitch) stitched into the ground pour. Route the SWDIO/SWCLK pair as a 50 ohm impedance-controlled differential pair with ground shielding to avoid debug-session lockups at 48 MHz core clock.
Do not assume the ATSAMC20G15A-MUT is 3.3 V tolerant only - it natively supports 5 V I/O on PAxx and PBxx pins, but PB04-PB07 and PB08-PB11 are NOT 5 V tolerant when configured as SERCOM or PTC lines. Confirm the SERCOM mux in the Microchip ASF/MPLAB Harmony framework before connecting 5 V peripherals. The CAN-FD peripheral requires a separate CAN transceiver such as ATA6563; the MCU's CAN pins are logic-level only and cannot drive a CAN bus directly.
When routing the external crystal on PA14 (XIN) and PA15 (XOUT), keep the traces under 5 mm, place load capacitors within 2 mm of the pins, and surround the crystal network with a ground guard ring. According to Microchip's SAM C20 hardware design guide, this layout is required to meet the 48 MHz PLL jitter specification and avoid CAN-FD bit-time violations in time-critical automotive networks.
Thông tin tuân thủ
RoHS and REACH compliant per Microchip product page. AEC-Q100 Grade 1 qualified per SAM C20 datasheet. Lead-free and halogen-free packaging. Conflict-minerals reporting compliant.
