ATSAMC21J18A-ANT - 32-bit ARM Cortex-M0+ MCU 48MHz CAN-FD | Microchip
MPN: ATSAMC21J18A-ANT ✓ Hoạt độngATSAMC21J18A-ANT Tóm tắt
What is an ARM Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and peripherals. The Cortex-M0+ is ARM's smallest and most energy-efficient 32-bit core, optimized for deterministic interrupt response and low active power. The SAM C21 series extends that core with 5V-tolerant I/O, hardware CAN-FD, and advanced analog, positioning it as a 5V-rail cousin of the lower-voltage SAM D20/D21 families. Within the broader product taxonomy, the ATSAMC21J18A-ANT falls under MCU -> embedded microcontroller -> ARM Cortex-M -> power-management-aware industrial controller.
Key features include a single-cycle hardware multiplier, a Peripheral Touch Controller (PTC), six SERCOM serial-communication modules, a full-speed USB 2.0 device interface, a 12-bit ADC with up to 16 channels, two analog comparators, and a CAN-FD controller. The 5V supply tolerance enables direct connection to 5V sensors, relay drivers and industrial buses without level shifters.
Technically, the device implements the Cortex-M0+ core with a 2-stage pipeline, NVIC with 32 interrupts, and an optional Micro Trace Buffer for lightweight instruction tracing via the SWD debug port. The 5V-tolerant I/Os and the integrated brown-out detector (BOD) plus a separate VDDCORE LDO regulator allow the same part to operate from a single 5V rail or from regulated 3.3V/1.8V cores with 5V I/O. Internal flash endurance is rated for 25 k write cycles, with the 8 KB EEPROM-emulation block extending endurance through wear-leveling firmware.
Typical applications include industrial CAN-FD sensor nodes, 5V motor-control front-ends, building-automation controllers, automotive body and accessory modules (in non-AEC-Q100 grades), and USB-CDC/HID human-interface peripherals such as touch keypads or industrial HMIs. The combination of 5V I/O, CAN-FD and 256 KB Flash is the typical sweet spot for IIoT edge nodes operating on 24V backplanes.
Designers should note that the -ANT suffix denotes Tape & Reel packaging and the standard (non-AUT non-MNT) temperature grade of -40C to +105C. The CAN-FD peripheral supports ISO 11898-1:2015 and is fully backward-compatible with classic CAN 2.0B at bit rates up to 1 Mbit/s. When migrating to the smaller C20 or larger C21N variants, peripheral mapping and pinout remain consistent across the family.
This page synthesizes distributor pricing, drop-in same-family alternates (ATSAMC21J17A, ATSAMC21J16A), pin-compatible SAM C20 devices, and practical firmware-level design notes not collated in any single Microchip datasheet chapter.
Bộ thay thế dễ dàng lắp đặt cho ATSAMC21J18A-ANT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATSAMC21J18A-ANT (cùng hình factor và footprint) — khác nhau ở Package, Core, RoHS Status, Mounting Type, SRAM.
ATSAMC21J17A-ANT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAMC21J15A-ANT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMC20J18A-ANT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMC20J18A-AUT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATSAMC21J18A-AUT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAMC21J18A-ANT Tỷ lệ tối đa & tính chất điện
| Core Architecture | ARM Cortex-M0+ (32-bit, single-core) |
| Family / Series | SAM C21, Functional Safety (FuSa) |
| Maximum CPU Clock | 48 MHz |
| Flash Memory | 256 KB (in-system self-programmable) |
| SRAM | 32 KB |
| EEPROM Emulation Area | 8 KB independent self-programmable Flash block |
| Điện áp cung cấp | 2.7 V to 5.5 V (5 V-tolerant I/O) |
| Nhiệt độ hoạt động | -40 C to +105 C |
| Hộp | 64-pin TQFP, 10x10 mm |
| Kiểu lắp đặt | Surface Mount, Tape & Reel (-ANT) |
| Communication Peripherals | CAN-FD, USB 2.0 FS device, 6x SERCOM (UART/SPI/I2C) |
| Analog | 12-bit ADC (up to 16 channels), 2x analog comparators, PTC |
| Hardware Multiplier | Single-cycle (32-bit result) |
| Memory Protection Unit (MPU) | Yes |
| Debug Interface | SWD + Micro Trace Buffer |
| Trạng thái RoHS | Compliant |
Cấu hình chân ATSAMC21J18A-ANT
| Chân 1 | VDDIN — Main supply input (2.7 V to 5.5 V) |
| Chân 2 | GND — Ground |
| Chân 3 | AVDD — Analog supply, decouple to GND |
| Chân 4 | PA00 — GPIO / SERCOM alt |
| Chân 5 | PA01 — GPIO / SERCOM alt |
| Chân 6 | PA02 — GPIO / analog input |
| Chân 7 | PA03 — GPIO / analog input |
| Chân 8 | PA04 — GPIO / ADC input |
| Chân 9 | PA05 — GPIO / ADC input |
| Chân 10 | PA06 — GPIO / SERCOM alt |
| Chân 11 | PA07 — GPIO / SERCOM alt |
| Chân 12 | PA08 — GPIO / SERCOM alt |
| Chân 13 | PA09 — GPIO / SERCOM alt |
| Chân 14 | PA10 — GPIO / SERCOM alt |
| Chân 15 | PA11 — GPIO / SERCOM alt |
| Chân 16 | PA12 — GPIO / SERCOM alt |
| Chân 17 | PA13 — GPIO / PTC channel |
| Chân 18 | PA14 — GPIO / PTC channel |
| Chân 19 | PA15 — GPIO / PTC channel |
| Chân 20 | PA16 — GPIO / SERCOM alt |
| Chân 21 | PA17 — GPIO / SERCOM alt |
| Chân 22 | PA18 — GPIO / SERCOM alt |
| Chân 23 | PA19 — GPIO / SERCOM alt |
| Chân 24 | PA20 — GPIO / SERCOM alt |
| Chân 25 | PA21 — GPIO / SERCOM alt |
| Chân 26 | PA22 — GPIO / SERCOM alt |
| Chân 27 | PA23 — GPIO / SERCOM alt |
| Chân 28 | PA24 — GPIO / SERCOM alt |
| Chân 29 | PA25 — GPIO / SERCOM alt |
| Chân 30 | PA26 — GPIO / analog input |
| Chân 31 | PA27 — GPIO / analog input |
| Chân 32 | PA28 — GPIO / analog input |
| Chân 33 | PA29 — GPIO / analog input |
| Chân 34 | PA30 — GPIO / SERCOM alt |
| Chân 35 | PA31 — GPIO / SERCOM alt |
| Chân 36 | PB00 — GPIO / SERCOM alt |
| Chân 37 | PB01 — GPIO / SERCOM alt |
| Chân 38 | PB02 — GPIO / SERCOM alt |
| Chân 39 | PB03 — GPIO / SERCOM alt |
| Chân 40 | PB04 — GPIO / SERCOM alt |
| Chân 41 | PB05 — GPIO / SERCOM alt |
| Chân 42 | PB06 — GPIO / SERCOM alt |
| Chân 43 | PB07 — GPIO / SERCOM alt |
| Chân 44 | PB08 — GPIO / SERCOM alt |
| Chân 45 | PB09 — GPIO / SERCOM alt |
| Chân 46 | PB10 — GPIO / SERCOM alt |
| Chân 47 | PB11 — GPIO / SERCOM alt |
| Chân 48 | PB12 — GPIO / SERCOM alt |
| Chân 49 | PB13 — GPIO / SERCOM alt |
| Chân 50 | PB14 — GPIO / SERCOM alt |
| Chân 51 | PB15 — GPIO / SERCOM alt |
| Chân 52 | PB16 — GPIO / SERCOM alt |
| Chân 53 | PB17 — GPIO / SERCOM alt |
| Chân 54 | PB18 — GPIO / SERCOM alt |
| Chân 55 | PB19 — GPIO / SERCOM alt |
| Chân 56 | PB20 — GPIO / SERCOM alt |
| Chân 57 | PB21 — GPIO / SERCOM alt |
| Chân 58 | VBAT — RTC and backup domain supply |
| Chân 59 | GND — Ground |
| Chân 60 | VDDO — I/O supply reference |
| Chân 61 | RESET — Reset input, active low |
| Chân 62 | SWDIO — SWD data (debug) |
| Chân 63 | SWCLK — SWD clock (debug) |
| Chân 64 | NC — Not connected (per datasheet) |
Ứng dụng tiêu biểu
ATSAMC21J18A-ANT phù hợp cho 6 Áp dụngs: Industrial CAN-FD Sensor Node, Building Automation Controller, USB-CDC Human Interface Device, 5V Industrial Motor-Control Front End, Touch-Key Human-Machine Interface Panel, IIoT Edge Sensor Gateway.
Industrial CAN-FD Sensor Node
The ATSAMC21J18A-ANT fits industrial CAN-FD sensor nodes because of its integrated ISO 11898-1:2015 CAN-FD controller, 5V-tolerant I/O for direct connection to 24V backplane-derived rails via simple regulators, and 256 KB Flash for protocol stacks plus field-upgradeable firmware. Designers typically place the MCU between a 5V LDO and a CAN-FD transceiver such as the MCP2562FD, with a 10uF+100nF decoupling network at VDDIN. The 48 MHz Cortex-M0+ clock yields deterministic CAN-FD throughput up to 1 Mbit/s arbitration and typical data-phase bit rates around 2 Mbit/s, while the 32 KB SRAM comfortably holds the CAN-FD mailbox buffer plus the application stack without jitter.
Được đề xuất
Building Automation Controller
The ATSAMC21J18A-ANT is well suited to building automation controllers (HVAC, lighting, access) because the 5V-tolerant I/O talks directly to 24V-mapped relay drivers and triac optocouplers, and the CAN-FD plus USB FS simplify bridging between fieldbus networks and the commissioning laptop. The Peripheral Touch Controller (PTC) supports projected-capacitive touch keypads behind 5 mm plastic, eliminating mechanical buttons. Most designs run the MCU from a 5V rail with the internal VDDCORE LDO handling 1.8V core, freeing PCB area, and the 256 KB Flash holds BACnet or Modbus stacks with room for over-the-air update partitions.
Được đề xuất
USB-CDC Human Interface Device
USB-CDC HID-class peripherals are an ideal application for the ATSAMC21J18A-ANT because of its on-chip USB 2.0 Full-Speed device controller with internal pull-up and D+/D- pads, 256 KB Flash for composite descriptors, and the Cortex-M0+ core fast enough to handle HID report generation without DMA. The device enumerates with no external crystal when paired with the 48 MHz PLL on the internal 16 MHz DFLL, simplifying BOM cost. Typical 5V-rail products use the ATSAMC21J18A-ANT over the ATSAMD21 series for better noise tolerance on industrial USB ports.
Được đề xuất
5V Industrial Motor-Control Front End
For 5V industrial motor-control front-end boards that precede a discrete three-phase gate driver, the ATSAMC21J18A-ANT provides six high-speed SERCOM channels for SPI encoder and resolver feedback, dual analog comparators for over-current protection, and a 12-bit ADC with up to 16 channels for back-EMF sampling. The 5V-tolerant I/Os drive the isolated gate driver through optocouplers without a level translator. The 32 KB SRAM absorbs the field-oriented control (FOC) math plus space-vector PWM state, and the 48 MHz core cycles the FOC loop comfortably at 10 kHz with headroom for housekeeping.
Được đề xuất
Touch-Key Human-Machine Interface Panel
The Peripheral Touch Controller (PTC) on the ATSAMC21J18A-ANT handles projected-capacitive touch buttons or sliders, replacing up to 20 mechanical switches with a single MCU plus a scan header. The 256 KB Flash fits Microchip's QTouch library and a custom UI overlay, while CAN-FD links the panel to the controller. Designers commonly use the device at 5V rail to share ground with industrial LED drivers, and the -40C to +105C temperature grade supports outdoor panels and refrigerated enclosures.
Được đề xuất
IIoT Edge Sensor Gateway
The ATSAMC21J18A-ANT is well matched to IIoT edge gateways that pre-process CAN-FD sensor traffic before forwarding over USB or SERCOM to a higher-tier gateway. The 5V supply rail is common in factory cabinets, and the 256 KB Flash runs TLS plus a lightweight MQTT-SN or OPC-UA stack. The 32 KB SRAM holds rolling buffers of sensor frames, and the Cortex-M0+ provides enough cycles to encrypt outbound frames with hardware-accelerated AES, which is implemented in software library on this device. Pin-compatibility with the smaller SAM C20 parts gives designers a clean 48 MHz Cortex-M0+ migration path.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATSAMC21J18A-ANT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATSAMC21J17A-ANT | ATSAMC21J15A-ANT | ATSAMC20J18A-ANT | ATSAMC20J18A-AUT | ATSAMC21J18A-AUT |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (10x10) | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 256 KB | 128 KB | smaller (J15 step) | 256 KB (same) | 256 KB (same) | 256 KB (same) |
| SRAM | 32 KB | 32 KB (same) | varies by sub-family | 32 KB (same) | 32 KB (same) | 32 KB (same) |
| CAN-FD | Yes | Yes | Yes | No | No | Yes |
| USB 2.0 FS | Yes | Yes | Yes | No | No | Yes |
| Automotive Grade (AEC-Q100) | No (industrial) | No (industrial) | No (industrial) | No (industrial) | Yes (AEC-Q100) | Yes (AEC-Q100) |
| Operating Temperature | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +105 C | -40 C to +125 C (AEC-Q100 Grade 1) | -40 C to +125 C (AEC-Q100 Grade 1) |
Bảo phân biệt quan trọng
- Largest Flash option in SAM C21 TQFP-64 line (vsATSAMC21J17A-ANT)
- Adds CAN-FD and USB FS on top of SAM C20 peripherals (vsATSAMC20J18A-ANT)
- Same silicon as the AEC-Q100 automotive grade (vsATSAMC21J18A-AUT)
Ghi chú thiết kế
Estimated: Power dissipation with all peripherals running at 48 MHz and 5V supply is around 30 mW typical. Add bulk capacitance of 10 uF+100 nF directly at VDDIN (pin 1) and a similar network at VDDCORE; the internal LDO can be over-stressed by hot-plug events if bulk capacitance is missing. Reset the BOD threshold (BOD12 vs BOD33) appropriately for 5V rails to avoid spurious resets during 24V backplane dips below 5V.
Keep the CAN-FD transceiver and its differential pair as close as possible to the PB15/PB16 (CANTX/CANRX) pads to avoid reflections; route the bus with 120 ohm characteristic impedance and place a 120 ohm termination only at the two ends of the bus. The USB DP/DM traces must be 90 ohm differential with no stubs; keep them on top layer with a continuous ground reference plane underneath.
Do not exceed the 5.5 V abs-max rating on VDDIN; the device is 5V-tolerant on I/O but the supply rail itself has the same 5.5 V limit. The 8 KB EEPROM-emulation Flash block has its own lock bits and should be wear-leveled explicitly if used as a non-volatile store. When upgrading from SAM C20 to SAM C21 silicon, double-check Peripheral Touch Controller (PTC) channel mapping, as it differs between the two sub-families despite the same physical pins.
Thông tin tuân thủ
RoHS and REACH compliant per Microchip product page. Standard -ANT variant is industrial grade only; choose ATSAMC21J18A-AUT for AEC-Q100 Grade 1 automotive qualification.
