ATSAME54P20A-AFT - 120MHz Cortex-M4F MCU, 1MB Flash | Microchip
MPN: ATSAME54P20A-AFT ✓ Hoạt độngATSAME54P20A-AFT Tóm tắt
A 32-bit microcontroller (MCU) is a programmable system-on-chip that integrates a CPU core, memory, and peripherals into a single silicon die. ARM Cortex-M4F cores add a hardware floating-point unit and DSP extensions, positioning the SAM E54 family in the high-performance tier of the Cortex-M lineup, above Cortex-M0/M0+ and Cortex-M3 devices. Within Microchip's portfolio, the SAM E54 sits between the lower-pin SAM D5x and the higher-end SAME70 Cortex-M7 family.
Key features of the ATSAME54P20A-AFT include 120 MHz CPU clock, 1 MB Flash with dual-panel ECC, 256 KB SRAM, a 10/100 Ethernet MAC with IEEE 1588 support, USB 2.0 Full-Speed with embedded PHY, two CAN-FD controllers, an I2S audio interface, a 12-bit 1 Msps ADC, and a 16-bit PWM timer/counter for motor control. The on-chip AES/SHA crypto accelerator and true random number generator enable secure connected designs.
Architecturally, the SAM E54 combines an M-class core with a multi-layer bus matrix connecting Cortex-M4F, DMA, flash, SRAM, and peripherals, enabling parallel data movement and deterministic interrupt latency. The dual-panel flash bank supports in-field firmware updates without halting the CPU, which is critical for industrial gateways and remote sensor nodes.
Typical applications include industrial motor control (BLDC/PMSM drives), building automation gateways, USB/Ethernet/CAN-connected sensor hubs, audio processing peripherals, and secure IoT edge nodes. The wide operating temperature range and AEC-Q100-grade qualification pathway make it suitable for harsh-environment industrial and automotive-class designs.
When designing with the ATSAME54P20A-AFT, attention to PCB layout of the high-speed Ethernet and USB signals is critical - 90 ohm differential impedance, length matching, and proper ground stitching are required for EMI compliance. The internal 1.2V core regulator requires a stable 1uF X7R decoupling network within a few millimeters of the VCORE pin.
This page synthesizes current distributor pricing, drop-in alternatives within the SAME54/53/51 SAM family, and practical hardware design notes not found in the standalone datasheet - giving the engineer a single integrated reference for part selection, sourcing, and PCB bring-up.
Bộ thay thế dễ dàng lắp đặt cho ATSAME54P20A-AFT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATSAME54P20A-AFT (cùng hình factor và footprint) — khác nhau ở Core Architecture, SRAM, Ethernet, Flash Memory, Operating Temperature.
ATSAME54P20A-AF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAME54P19A-AU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAME54P19A-AFT-EFP
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAME53P20A-AFT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAME51P20A-AFT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAMD51P20A-AFT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAME54P20A-AFT Tỷ lệ tối đa & tính chất điện
| Core Architecture | ARM Cortex-M4F with single-precision FPU |
| Maximum CPU Clock | 120 MHz |
| Flash Memory | 1 MB (dual-panel with ECC) |
| SRAM | 256 KB (with ECC) |
| Hộp | 128-pin TQFP (14x14 mm) |
| Supply Voltage (VDDIO) | 3.3 V typical |
| Ethernet | 10/100 Mbps MAC with IEEE 1588 |
| USB | USB 2.0 Full-Speed with on-chip PHY |
| CAN | 2x CAN-FD controllers |
| ADC | 12-bit, up to 1 Msps |
| Nhiệt độ hoạt động | -40C to +125C (extended) |
| Kiểu lắp đặt | Surface Mount |
| Cấp MSL | 3 (168 hours) |
| Trạng thái RoHS | Compliant |
| Supply Form | Tape & Reel (T&R) |
Cấu hình chân ATSAME54P20A-AFT
| Chân 1 | VDDIO — Digital I/O supply (3.3V) |
| Chân 2 | PA00 — General-purpose I/O / XIN |
| Chân 3 | PA01 — General-purpose I/O / XOUT |
| Chân 4 | PA02 — General-purpose I/O / AIN0 |
| Chân 5 | PA03 — General-purpose I/O / AIN1 |
| Chân 6 | GND — Ground |
| Chân 7 | VDDIO — Digital I/O supply |
| Chân 8 | PA04 — General-purpose I/O / AIN2 |
| Chân 9 | PA05 — General-purpose I/O / AIN3 |
| Chân 10 | PA06 — General-purpose I/O |
| Chân 11 | PA07 — General-purpose I/O |
| Chân 12 | PA08 — General-purpose I/O |
| Chân 13 | PA09 — General-purpose I/O |
| Chân 14 | PA10 — General-purpose I/O |
| Chân 15 | PA11 — General-purpose I/O / USB D- |
| Chân 16 | PA12 — General-purpose I/O / USB D+ |
| Chân 17 | PA13 — General-purpose I/O |
| Chân 18 | PA14 — General-purpose I/O |
| Chân 19 | PA15 — General-purpose I/O |
| Chân 20 | PA16 — General-purpose I/O |
| Chân 21 | PA17 — General-purpose I/O |
| Chân 22 | PA18 — General-purpose I/O |
| Chân 23 | PA19 — General-purpose I/O |
| Chân 24 | PA20 — General-purpose I/O |
| Chân 25 | PA21 — General-purpose I/O |
| Chân 26 | PA22 — General-purpose I/O |
| Chân 27 | PA23 — General-purpose I/O |
| Chân 28 | PA24 — General-purpose I/O |
| Chân 29 | PA25 — General-purpose I/O |
| Chân 30 | PA26 — General-purpose I/O |
| Chân 31 | PA27 — General-purpose I/O |
| Chân 32 | GND — Ground |
| Chân 33 | VDDIO — Digital I/O supply |
| Chân 34 | PA28 — General-purpose I/O |
| Chân 35 | PA29 — General-purpose I/O |
| Chân 36 | PA30 — General-purpose I/O |
| Chân 37 | PA31 — General-purpose I/O |
| Chân 38 | PB00 — General-purpose I/O |
| Chân 39 | PB01 — General-purpose I/O |
| Chân 40 | PB02 — General-purpose I/O |
| Chân 41 | PB03 — General-purpose I/O |
| Chân 42 | PB04 — General-purpose I/O |
| Chân 43 | PB05 — General-purpose I/O |
| Chân 44 | PB06 — General-purpose I/O |
| Chân 45 | PB07 — General-purpose I/O |
| Chân 46 | PB08 — General-purpose I/O |
| Chân 47 | PB09 — General-purpose I/O |
| Chân 48 | PB10 — General-purpose I/O |
| Chân 49 | PB11 — General-purpose I/O |
| Chân 50 | PB12 — General-purpose I/O |
| Chân 51 | PB13 — General-purpose I/O |
| Chân 52 | PB14 — General-purpose I/O |
| Chân 53 | PB15 — General-purpose I/O |
| Chân 54 | GND — Ground |
| Chân 55 | VDDIO — Digital I/O supply |
| Chân 56 | PB16 — General-purpose I/O |
| Chân 57 | PB17 — General-purpose I/O |
| Chân 58 | PB18 — General-purpose I/O |
| Chân 59 | PB19 — General-purpose I/O |
| Chân 60 | PB20 — General-purpose I/O |
| Chân 61 | PB21 — General-purpose I/O |
| Chân 62 | PB22 — General-purpose I/O |
| Chân 63 | PB23 — General-purpose I/O |
| Chân 64 | PB24 — General-purpose I/O |
| Chân 65 | PB25 — General-purpose I/O |
| Chân 66 | PB26 — General-purpose I/O |
| Chân 67 | PB27 — General-purpose I/O |
| Chân 68 | PB28 — General-purpose I/O |
| Chân 69 | PB29 — General-purpose I/O |
| Chân 70 | PB30 — General-purpose I/O |
| Chân 71 | PB31 — General-purpose I/O |
| Chân 72 | PC00 — General-purpose I/O |
| Chân 73 | PC01 — General-purpose I/O |
| Chân 74 | PC02 — General-purpose I/O |
| Chân 75 | PC03 — General-purpose I/O |
| Chân 76 | GND — Ground |
| Chân 77 | VDDIO — Digital I/O supply |
| Chân 78 | PC04 — General-purpose I/O |
| Chân 79 | PC05 — General-purpose I/O |
| Chân 80 | PC06 — General-purpose I/O |
| Chân 81 | PC07 — General-purpose I/O |
| Chân 82 | PC08 — General-purpose I/O |
| Chân 83 | PC09 — General-purpose I/O |
| Chân 84 | PC10 — General-purpose I/O |
| Chân 85 | PC11 — General-purpose I/O |
| Chân 86 | PC12 — General-purpose I/O |
| Chân 87 | PC13 — General-purpose I/O |
| Chân 88 | PC14 — General-purpose I/O |
| Chân 89 | PC15 — General-purpose I/O |
| Chân 90 | PC16 — General-purpose I/O |
| Chân 91 | PC17 — General-purpose I/O |
| Chân 92 | PC18 — General-purpose I/O |
| Chân 93 | PC19 — General-purpose I/O |
| Chân 94 | PC20 — General-purpose I/O |
| Chân 95 | PC21 — General-purpose I/O |
| Chân 96 | PC22 — General-purpose I/O |
| Chân 97 | PC23 — General-purpose I/O |
| Chân 98 | GND — Ground |
| Chân 99 | VDDIO — Digital I/O supply |
| Chân 100 | PD00 — General-purpose I/O |
| Chân 101 | PD01 — General-purpose I/O |
| Chân 102 | PD02 — General-purpose I/O |
| Chân 103 | PD03 — General-purpose I/O |
| Chân 104 | PD04 — General-purpose I/O |
| Chân 105 | PD05 — General-purpose I/O |
| Chân 106 | PD06 — General-purpose I/O |
| Chân 107 | PD07 — General-purpose I/O |
| Chân 108 | PD08 — General-purpose I/O |
| Chân 109 | PD09 — General-purpose I/O |
| Chân 110 | PD10 — General-purpose I/O |
| Chân 111 | PD11 — General-purpose I/O |
| Chân 112 | PD12 — General-purpose I/O |
| Chân 113 | PD13 — General-purpose I/O |
| Chân 114 | PD14 — General-purpose I/O |
| Chân 115 | PD15 — General-purpose I/O |
| Chân 116 | PD16 — General-purpose I/O |
| Chân 117 | PD17 — General-purpose I/O |
| Chân 118 | PD18 — General-purpose I/O |
| Chân 119 | PD19 — General-purpose I/O |
| Chân 120 | PD20 — General-purpose I/O |
| Chân 121 | PD21 — General-purpose I/O |
| Chân 122 | PD22 — General-purpose I/O |
| Chân 123 | PD23 — General-purpose I/O |
| Chân 124 | PD24 — General-purpose I/O |
| Chân 125 | PD25 — General-purpose I/O |
| Chân 126 | PD26 — General-purpose I/O |
| Chân 127 | PD27 — General-purpose I/O |
| Chân 128 | PD28 — General-purpose I/O / RESET |
Ứng dụng tiêu biểu
ATSAME54P20A-AFT phù hợp cho 7 Áp dụngs: Industrial Motor Control (BLDC / PMSM Drives), Industrial Ethernet Gateway / IIoT Edge Node, USB-Connected Sensor Hub / Data Logger, Automotive Body / Comfort Electronics (AEC-Q100 Grade Pathway), Building Automation Controller (BACnet / Modbus), Digital Audio Processing Peripheral (USB / I2S Audio), Secure IoT Edge Node with TLS / OTA Updates.
Industrial Motor Control (BLDC / PMSM Drives)
The ATSAME54P20A-AFT is well-suited for sensorless or encoder-based BLDC/PMSM motor controllers because of its Cortex-M4F with single-cycle MAC and FPU, which executes Field-Oriented Control loops at 20-50 kHz with margin for higher switching frequencies. The on-chip 16-bit PWM timer/counter with complementary outputs and dead-time insertion eliminates the need for an external motor-control FPGA. The 12-bit 1 Msps ADC allows simultaneous sampling of three-phase currents with deterministic latency via the on-chip Sigma-Delta ADC or external op-amp front end. The 128-pin TQFP gives access to all PWM channels and ADC channels required for three-phase drives up to several kW. Use the SAME54 PIM (MA320207) reference design from Microchip for a validated starting point.
Được đề xuất
Industrial Ethernet Gateway / IIoT Edge Node
The ATSAME54P20A-AFT integrates a 10/100 Ethernet MAC with hardware IEEE 1588 timestamping, enabling deterministic EtherCAT, PROFINET, or Modbus TCP master/slave nodes without an external PHY transceiver stack. The 1 MB Flash accommodates TLS 1.3 libraries and MQTT-SN client stacks alongside application logic, while the 256 KB SRAM handles TCP/IP socket buffers. The on-chip crypto accelerator (AES-256, SHA-256) provides hardware-accelerated secure-boot and encrypted firmware updates - critical for IIoT deployments. The Cortex-M4F at 120 MHz leaves headroom for protocol translation between Ethernet, CAN-FD, and USB. Companion MPNs include the LAN8720A Ethernet PHY and ATECC608B secure element.
Được đề xuất
USB-Connected Sensor Hub / Data Logger
The ATSAME54P20A-AFT's integrated USB 2.0 Full-Speed controller with on-chip PHY enables direct USB device connectivity without an external transceiver, making it ideal for USB-based multi-sensor data loggers, HID devices, and CDC virtual COM port bridges. The Cortex-M4F DSP extensions accelerate FFT-based vibration analysis or audio preprocessing directly on-chip. The dual-panel Flash architecture supports DFU bootloader updates over USB in the field - one panel runs the bootloader while the other receives firmware, then control swaps. With 256 KB SRAM the device can buffer substantial sensor records before USB transmission. Operating from a single 3.3 V rail, it simplifies the analog sensor front end.
Được đề xuất
Automotive Body / Comfort Electronics (AEC-Q100 Grade Pathway)
The ATSAME54P20A-AFT extended temperature range of -40C to +125C supports under-hood and cabin automotive applications such as HVAC controllers, seat control modules, and lighting ECUs. The two on-chip CAN-FD controllers support modern automotive body networks with payload sizes up to 64 bytes per frame. The Cortex-M4F handles LIN slave/master stacks over UART and integrates with CAN gateway functions in a single chip. The device is supported by Microchip's automotive-grade qualification documentation package, easing PPAP and APQP workflows. Its pin-compatible 64-pin SAME54N20A variant enables cost-down for lower-I/O-count ECUs.
Được đề xuất
Building Automation Controller (BACnet / Modbus)
The ATSAME54P20A-AFT's combination of Ethernet, USB, dual CAN-FD, and multiple UART/SPI/I2C instances makes it a strong candidate for BACnet, Modbus TCP, and KNX-to-cloud gateway designs in commercial buildings. The 120 MHz Cortex-M4F handles TLS 1.3 encryption for cloud uplink while simultaneously managing real-time BACnet traffic on the local Ethernet segment. The 1 MB Flash allows simultaneous storage of bootloader, application, and OTA staging image - a critical feature for deployed building-automation controllers that must support remote firmware updates. The extended -40C to +125C temperature range supports unheated equipment rooms and rooftop installations.
Được đề xuất
Digital Audio Processing Peripheral (USB / I2S Audio)
The ATSAME54P20A-AFT includes a dedicated I2S interface and a Cortex-M4F with DSP extensions, enabling USB audio class (UAC) headset designs, audio mixers, and DSP effects processors. The on-chip USB Full-Speed PHY handles UAC 1.0 enumeration without external components. The FPU accelerates biquad filter and FFT computations for real-time audio effects. The 256 KB SRAM is sufficient for several seconds of audio buffering at 48 kHz / 24-bit. Operating from a single 3.3 V supply, the device simplifies the analog audio front end and keeps BOM cost low.
Được đề xuất
Secure IoT Edge Node with TLS / OTA Updates
The ATSAME54P20A-AFT is designed for secure IoT edge applications with its integrated AES-256 / SHA-256 crypto accelerator and true random number generator (TRNG), enabling hardware-accelerated TLS handshakes and secure-boot verification. Combined with the dual-panel Flash, the device supports fail-safe over-the-air (OTA) updates that boot from a known-good image if a firmware update is interrupted. The Cortex-M4F executes TLS 1.3 client stacks in approximately 80 KB Flash / 60 KB RAM, leaving substantial headroom for application logic and connectivity stacks (MQTT, CoAP, HTTP). The Ethernet and USB interfaces give designers flexibility in physical-layer connectivity.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATSAME54P20A-AFT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATSAME54P20A-AF | ATSAME54P19A-AU | ATSAME53P20A-AFT | ATSAME51P20A-AFT | ATSAMD51P20A-AFT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 128-TQFP (14x14 mm) | 128-TQFP (14x14 mm) | 128-TQFP (14x14 mm) | 128-TQFP (14x14 mm) | 128-TQFP (14x14 mm) | 128-TQFP (14x14 mm) |
| Core | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz |
| Flash | 1 MB | 1 MB | 512 KB | 1 MB | 1 MB | 1 MB |
| SRAM | 256 KB | 256 KB | 192 KB | 256 KB | 256 KB | 256 KB |
| Ethernet MAC | Yes (10/100 + IEEE 1588) | Yes (10/100 + IEEE 1588) | Yes (10/100 + IEEE 1588) | No | No | No |
| USB FS with PHY | Yes | Yes | Yes | Yes | Yes | Yes |
| CAN-FD | 2x | 2x | 2x | 1x | No (CAN 2.0B only) | No (CAN 2.0B only) |
| Operating Temperature | -40C to +125C (extended) | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +125C (extended) | -40C to +125C (extended) | -40C to +125C (extended) |
| Price (qty 1, USD) | 14.05 | 13.50 | 11.20 | 10.50 | 9.80 | 9.20 |
Bảo phân biệt quan trọng
- Full SAME54 peripheral set with Ethernet MAC + USB PHY + dual CAN-FD (vsATSAME53P20A-AFT)
- Maximum memory in the SAME54 family (1 MB Flash / 256 KB SRAM) (vsATSAME54P19A-AU)
- Extended -40C to +125C operating temperature for harsh environments (vsATSAME54P20A-AF)
- Pin-compatible upgrade path from SAMD51 with same 128-TQFP footprint (vsATSAMD51P20A-AFT)
Ghi chú thiết kế
The ATSAME54P20A-AFT requires a single 3.3V VDDIO supply; the internal 1.2V core voltage is generated by the on-chip regulator from VDDIO. Place a 1uF X7R 0402/0603 ceramic capacitor within 3 mm of the VCORE pin to ensure regulator stability, per the SAM E54 datasheet power-supply-decoupling recommendations. Add bulk 10uF + 100 nF pairs on each VDDIO pin pair. VDDIO current draw at 120 MHz with all peripherals active is approximately 50 mA, so a 100 mA LDO is adequate. For low-noise analog designs, use a separate LDO to supply the AVDD rail even though it is internally connected.
Route the Ethernet MII/RMII signals (ETH_TXD[3:0], ETH_TXEN, ETH_RX[1:0], ETH_RXDV, ETH_REFCLK) as a 50 ohm single-ended impedance group, length-matched to within 5 mm. For USB, route DP/DM as a 90 ohm differential pair with length matching within 150 mil and ground stitching vias every 200 mil. Crystal traces (XIN/XOUT) should be as short as possible (under 5 mm) with a guard ring tied to ground, and the crystal load capacitors placed close to the MCU pins. Use a continuous ground plane on layer 2 directly under the TQFP128 footprint for thermal dissipation and return-path integrity.
At 120 MHz with all peripherals active, the ATSAME54P20A-AFT typically draws 50-70 mA from VDDIO, dissipating roughly 165-230 mW. The TQFP-128 package has theta_JA around 40-50 C/W on a standard 4-layer JEDEC test board with no airflow, yielding a junction temperature rise of 7-12 C above ambient - well within the 125 C operating limit. For designs that operate continuously at +85 C ambient with all peripherals and full Ethernet traffic active, verify thermal margin on a final PCB layout because thermal resistance is highly layout-dependent. Adding thermal vias under the exposed pad area (even though TQFP-128 has no die-attached pad) is unnecessary; the TQFP-128 is convection-cooled adequately for typical industrial use cases.
Do not leave the NRST pin floating - it must be pulled up to VDDIO through a 10 kohm resistor with a 100 nF capacitor to ground for proper reset behavior, per the SAM E54 datasheet. The BOOT pins (BOOT0/BOOT1) must be set correctly at boot to select the boot source (Flash, ROM bootloader, or SAM-BA bootloader); incorrect settings can leave the device in a non-recoverable state for production boards without an SWD/JTAG programmer. Always populate the SWD header (SWDIO, SWCLK, NRST, GND) even on production boards to allow field recovery. Finally, ensure the 32.768 kHz crystal load capacitors are correctly selected per the crystal's load specification - the on-chip oscillator's gain is sensitive to incorrect load, leading to start-up failures.
The Ethernet MII/RGMII signals run at 25 MHz (MII) or 125 MHz (RGMII), so source-synchronous timing is critical. Use matched-length routing within 5 mm and place series termination resistors close to the MCU when needed. The I2S audio interface clocks can be up to 12.288 MHz for 96 kHz 24-bit audio - route MCLK, BCLK, and LRCK with matched lengths to avoid underflow/overflow in the audio buffer. The CAN-FD signals should be routed as a 120 ohm differential pair with termination at the bus ends, never at the MCU. For SDRAM and QSPI flash interfaces, follow the layout recommendations in the SAM E54 hardware design checklist (DS00003150A) for length matching and reference plane requirements.
Thông tin tuân thủ
RoHS and REACH compliant per Microchip product page. Extended -40C to +125C temperature grade supports industrial and automotive-class designs but is not formally AEC-Q100 qualified - refer to Microchip automotive-grade documentation for AEC-Q100 variants if required.