ATTINY13A-SUR - 20MHz 8-Bit AVR Microcontroller | Microchip (Tape & Reel)
MPN: ATTINY13A-SUR ✓ Hoạt độngATTINY13A-SUR Tóm tắt
An 8-bit microcontroller is a compact embedded-processing IC that combines a processor core, nonvolatile program memory, data memory, and peripherals on one die. The ATTINY13A belongs to the TinyAVR family within Microchip's AVR portfolio. Its enhanced RISC architecture executes many instructions in a single clock cycle, supporting processing throughput approaching 1 MIPS per MHz while allowing designs to balance speed against power consumption.
The principal features of the ATTINY13A-SUR include 1 KB of ISP Flash, 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and four 10-bit analog-to-digital converter channels. Its operating range of 1.8 V to 5.5 V supports low-voltage battery-powered equipment as well as conventional 5 V systems. In-system programming and ICSP interfaces support programming and debugging without removing the microcontroller from its circuit.
The device uses the AVR enhanced RISC architecture and can reach 20 MIPS throughput at a 20 MHz clock. This processing rate is more than adequate for compact control tasks involving digital I/O, timing, simple control logic, and analog signal measurement. The ATtiny13A-SU combines this processing capability with a small memory footprint, making it suitable for cost- and power-sensitive embedded products rather than connectivity-heavy or high-memory applications.
Typical uses include small motor controllers, temperature-sensor interfaces, battery monitors, LED controllers, appliance controls, hobby electronics, and simple sensor nodes. The four-channel 10-bit ADC is particularly useful when a design needs several analog inputs but does not require the memory, processing, or peripheral resources of a larger microcontroller family.
For new layouts, preserve the ATtiny13A pin assignments and provide a decoupling capacitor close to VCC. Confirm the selected clock source, brown-out configuration, programming connector, and ADC reference arrangement against the manufacturer datasheet. Changes to package suffix, clock specification, or operating mode can alter qualification, programming, or temperature requirements even when the basic function remains the same.
This product page consolidates the ATTINY13A-SUR electrical characteristics, package information, pin assignments, lifecycle information, verified drop-in references, and practical design guidance. It supports engineers comparing the 8-pin SOIC implementation with documented alternatives without confusing electrical compatibility, package compatibility, and broader functional similarity.
Bộ thay thế dễ dàng lắp đặt cho ATTINY13A-SUR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATTINY13A-SUR (cùng hình factor và footprint) — khác nhau ở Package.
ATTINY13A-SH
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATTINY13-20SU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATTINY13A-SUR Tỷ lệ tối đa & tính chất điện
| Microcontroller Type | 8-bit AVR RISC-based microcontroller |
| Tần số xung maksimum | 20 MHz |
| Operating Voltage Range | 1.8 V to 5.5 V |
| Flash Memory | 1 KB |
| Flash Organization | 512 x 16 bits |
| EEPROM Memory | 64 bytes |
| SRAM | 64 bytes |
| Register File | 32 bytes |
| ADC Resolution | 10 bits |
| ADC Channels | 4 channels |
| Maximum Throughput | 20 MIPS at 20 MHz |
| Instruction Throughput | Approximately 1 MIPS per MHz |
| Processor Architecture | AVR enhanced RISC |
| Process Technology | Low-power CMOS |
| Hộp | 8-pin SOIC |
| Package Designation | 8S2 |
| Số chân | 8 pins |
| Kiểu lắp đặt | Surface mount |
| Programming Interface | In-system programming and ICSP |
| Debug Interface | MPLAB Snap compatible |
| Trạng thái vòng đời | Active |
Cấu hình chân ATTINY13A-SUR
| Chân 1 | PC0 — Port C input/output pin 0; also ADC0 and MOSI function |
| Chân 2 | PD0 — Port D input/output pin 0; also ADC0 and OC0A functions |
| Chân 3 | PD1 — Port D input/output pin 1; also ADC1 and OC0B functions |
| Chân 4 | GND — Ground supply connection |
| Chân 5 | PB0 — Port B input/output pin 0; also ADC2, OC1A, and INT0 functions |
| Chân 6 | PB1 — Port B input/output pin 1; also ADC3, OC1B, and INT1 functions |
| Chân 7 | PB2 — Port B input/output pin 2; also ADC4, OC1C, PCINT, and SCK functions |
| Chân 8 | VCC — Power supply input |
Ứng dụng tiêu biểu
ATTINY13A-SUR phù hợp cho 6 Áp dụngs: Compact Sensor Node, Battery-Powered Monitor, LED Lighting Controller, Small Appliance Controller, Simple Motor Control, Hobby Electronics and DIY Projects.
Compact Sensor Node
The ATTINY13A-SUR fits a small sensor node that measures several analog inputs and performs simple threshold or control logic. Its four-channel 10-bit ADC allows up to four analog signals to share one controller, while the 1.8 V minimum operating voltage supports low-voltage sensor systems. The 20 MHz AVR core provides processing approaching 1 MIPS per MHz without the overhead of a larger microcontroller. The main design constraint is memory: 1 KB of Flash and 64 bytes of SRAM require concise firmware, small data buffers, and careful peripheral use.
Được đề xuất
Battery-Powered Monitor
ATTINY13A-SUR is appropriate for a battery-powered voltage, current, or environmental monitor with intermittent operation. Its 1.8 V to 5.5 V range supports low-energy systems, while the four-channel 10-bit ADC can sample sensor outputs without a separate converter. At 20 MHz, the AVR enhanced RISC core offers sufficient control throughput for threshold evaluation, timers, and status indication. Because SRAM is limited to 64 bytes, process data as it arrives rather than buffering large histories. Low-power behavior and wake-up sources should be selected from the manufacturer configuration guidance.
Được đề xuất
LED Lighting Controller
The ATTINY13A-SUR can control LED banks, indicators, or simple lighting sequences where the design requires modest timing precision and limited code size. Its timer-capable GPIO, 20 MHz clock, and compact 8-pin SOIC package make it suitable for embedded lighting logic. The 1 KB Flash capacity favors short deterministic routines, while the 64-byte SRAM is sufficient for small counters and state variables rather than large frame buffers. Use PWM-capable pins for dimming and verify current limits with the appropriate transistor or driver stage.
Được đề xuất
Small Appliance Controller
ATTINY13A-SUR is suited to simple appliance controls that combine digital inputs, timed outputs, and one or more analog measurements. Its four-channel 10-bit ADC can monitor a sensor, potentiometer, or supply level, while the 8-bit AVR core executes timers, state machines, and safety checks. The 8-pin SOIC package supports compact PCB layouts, and the 1.8 V to 5.5 V range allows integration across common low- and higher-voltage rails. Designers should define actuator drive circuits separately and keep firmware within the 1 KB Flash and 64-byte SRAM limits.
Được đề xuất
Simple Motor Control
ATTINY13A-SUR can serve as the command processor for a small stepper, solenoid, or DC motor controller when the system requires only basic sequencing and limited feedback. The 20 MHz AVR core handles timers and state transitions, while the ADC channels can monitor position, current, or analog command inputs. Its limited memory makes it appropriate for direct fixed-sequence control rather than advanced motion algorithms or elaborate fieldbus communication. A suitable transistor driver, protection network, and current-limiting scheme are required because the microcontroller pins are not intended to drive motor current directly.
Được đề xuất
Hobby Electronics and DIY Projects
ATTINY13A-SUR is useful for hobby electronics, educational projects, and compact programmable prototypes. The AVR architecture is supported by established AVR programming workflows, and ISP or ICSP permits firmware updates and debugging in the assembled circuit. Its four ADC inputs enable analog experiments, while the 8-pin SOIC footprint supports breadboard and compact custom-board layouts. The main educational trade-off is the small memory budget, so projects should prioritize one clear control task and avoid adding libraries or features that exceed 1 KB of Flash.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATTINY13A-SUR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATTINY13A-SH | ATTINY13-20SU |
|---|---|---|---|
| Package | SOIC-8 (8S2) | SOIC-8 (8S2) | SOIC-8 |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Architecture | 8-bit AVR enhanced RISC | 8-bit AVR enhanced RISC | 8-bit AVR |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz |
| Programming | ISP and ICSP | ISP and ICSP | ISP and ICSP |
Bảo phân biệt quan trọng
- Compact 8-pin SOIC implementation with four ADC channels (vsATTINY13-20SU)
- Same-family ordering option without changing the documented 8S2 package interface (vsATTINY13A-SH)
- Defined low-voltage operation and active product status (vsATTINY13-20SU)
Ghi chú thiết kế
Place the supply decoupling capacitor directly between VCC on pin 8 and GND on pin 4, with the shortest practical connection to the device. Route the ICSP programming signals away from sensitive analog inputs and switching nodes. Because the ATtiny13A provides only eight pins, reserve PB0, PB1, and PC0 for programming or debug functions if they are also used for application signals. The Microchip MPLAB Snap interface uses two I/O pins and the reset line, so a production design should preserve access to those connections.
Treat ADC inputs as mixed-signal nodes even though the converter is only 10 bits. Connect the analog source through a suitable impedance, keep traces short, and route them away from clock, motor-control, and switching-converter nodes. Use the same ground reference for the sensor and microcontroller where possible. The four ADC channels and nominal 10-bit resolution are suitable for basic measurements, but accuracy also depends on reference stability, source impedance, acquisition time, and analog filtering specified in the manufacturer datasheet.
Do not treat ATTINY13A-SUR, ATTINY13A-SSH, ATTINY13A-SSUR, and ATTINY13A-SSU as interchangeable without checking the ordering code. Some distinctions concern packaging or delivery configuration, while others can affect ordering details. Likewise, do not assume the original ATTINY13 has identical BOD, POR, or analog-module behavior even though Microchip documents it as functionally identical and a drop-in replacement. Verify speed grade, temperature grade, fuse configuration, package drawing, and programming requirements before approving any substitution.
Budget the device against the selected clock and operating mode rather than using the 20 MHz headline rate as a continuous-power assumption. The ATtiny13A can operate from 1.8 V to 5.5 V, but current consumption varies with voltage, clock, peripherals, and sleep configuration. Use the manufacturer power-consumption curves for the final operating mode, especially for a battery-powered design. The 1 KB Flash and 64-byte SRAM limits also influence wake-up processing time and the duty cycle required for sensor sampling.
Thông tin tuân thủ
The active ATtiny13A product information, device datasheet, and distributor records do not provide the required categorical compliance declarations for this ordering code.