C8051F581-IQ - 50MHz 8-Bit 128KB Flash MCU | Silicon Labs
MPN: C8051F581-IQ ✓ Hoạt độngC8051F581-IQ Tóm tắt
An 8-bit microcontroller is a compact processor designed around an 8-bit data bus and integrated memory, analog, and communication peripherals. Within the product hierarchy, this device belongs to the embedded microcontroller class, then the 8051-compatible MCU family, and finally the Silicon Labs C8051F58x series. Its combination of deterministic peripheral control, 50 MIPS processing throughput, and a small quad flat package makes it suitable for gateway and body-electronics nodes where board area, real-time response, and interface flexibility are important.
Key features include 128 KB of flash for program storage, 8 KB of internal RAM, a maximum clock frequency of 50 MHz, and an operating supply range that includes 5 V systems. Integrated communications comprise SPI, I2C, and two UART interfaces, reducing the need for external serial controllers. Analog-to-digital conversion is supported at programmable throughputs up to 200 ksps, while a programmable-gain input stage allows the MCU to accommodate signals with different full-scale ranges. The automotive-focused family also supports mixed-signal sensing and communication-oriented designs.
The C8051F58x architecture combines a 50 MHz CISC core with dedicated hardware blocks for serial communication and analog measurement. Dedicated peripheral engines allow UART, SPI, I2C, and conversion activity to proceed with predictable timing, reducing the processing burden for protocol servicing and data acquisition. A 50 MIPS execution rate provides additional margin for control loops, filtering, diagnostics, and communication-stack tasks within a compact embedded design.
Typical applications include LIN or CAN gateway modules, automotive body-control units, industrial condition-monitoring equipment, actuator controllers, and compact data-acquisition panels. The 48-TQFP footprint also suits mixed-signal boards where a modest pin count is preferred over a very large leaded package. Because the MCU combines flash, RAM, serial interfaces, and analog conversion, a single-device design can replace a combination of a small processor and several supporting interface ICs.
For PCB layout, place the MCU's decoupling capacitors close to the supply pins and route analog inputs away from high-current switching nodes. Confirm the external oscillator requirements, reset configuration, and exposed programming interface against the manufacturer pin table before layout release. Firmware development also depends on the Silicon Labs C51 toolchain, so verify tool availability and device support before committing the part to a production schedule.
This page combines the verified manufacturer and distributor specifications for the C8051F581-IQ with package-level alternatives, interface-focused application guidance, comparison parameters, and practical design notes. It is intended to accelerate component selection, schematic review, and PCB planning for automotive, industrial, and embedded control designs.
Bộ thay thế dễ dàng lắp đặt cho C8051F581-IQ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với C8051F581-IQ (cùng hình factor và footprint) — khác nhau ở ADC Resolution, Package, Product Type, ADC Throughput, Flash Memory.
C8051F586-IQ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
C8051F580-IQ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
C8051F582-IQ
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →C8051F583-IQ
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →C8051F581-IQ Tỷ lệ tối đa & tính chất điện
| Product Type | 8-bit Flash Microcontroller |
| Series | C8051F58x |
| Core Architecture | 8051-compatible CISC |
| Tần số xung maksimum | 50 MHz |
| Maximum Processing Throughput | 50 MIPS |
| Flash Memory | 128 KB (128K x 8) |
| RAM | 8 KB |
| Điện áp cung cấp hoạt động | 2.5 V to 5 V |
| Nominal Supply Options | 2.5 V, 3.3 V, and 5 V |
| ADC Resolution | 12 bit |
| ADC Throughput | Up to 200 ksps |
| ADC Input INL | +/-1 LSB |
| UART Count | 2 |
| Serial Interfaces | SPI, 2x UART, and I2C |
| Programmable Analog Gain | Yes |
| Windowed Interrupt Generator | Yes, data dependent |
| Hộp | 48-TQFP, 7 x 7 mm |
| Số chân | 48 pins |
| Kiểu lắp đặt | Surface Mount |
| Application Classification | Automotive and Industrial |
Hướng dẫn cấu hình chân C8051F581-IQ 48-tqfp, 7 x 7 mm
Cấu hình chân cho C8051F581-IQ (48-tqfp, 7 x 7 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho C8051F581-IQ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
C8051F581-IQ phù hợp cho 6 Áp dụngs: Automotive Body-Control Module, Industrial Condition-Monitoring Controller, Compact Data-Acquisition Panel, Actuator and Motor-Control Node, LIN Gateway and Body-Network Interface, Embedded Industrial Sensor Interface.
Automotive Body-Control Module
The C8051F581-IQ suits a compact body-control module that monitors switches and sensors while coordinating actuators over serial links. Its 50 MHz core and 50 MIPS throughput provide headroom for debouncing, diagnostics, and communication tasks, while 128 KB of flash accommodates driver routines and calibration data. Two UART channels, SPI, and I2C allow the controller to connect external transceivers and sensors without multiple companion ICs. The 48-TQFP 7 x 7 mm package keeps the controller compact, although a CAN or LIN design must first confirm that the required bus controller is present on the selected device.
Được đề xuất
Industrial Condition-Monitoring Controller
The C8051F581-IQ can serve as the local controller in an industrial condition-monitoring node that samples analog sensors and transmits processed results. Its 12-bit ADC supports throughput up to 200 ksps with +/-1 LSB input nonlinearity, while programmable gain helps adapt the analog front end to different signal amplitudes. The 8 KB of RAM supports working buffers for filtering and protocol handling, and 128 KB of flash holds firmware and configuration data. SPI and I2C provide local sensor access, while UART links the module to a gateway. Design the analog input paths away from switching power nodes to preserve measurement accuracy.
Được đề xuất
Compact Data-Acquisition Panel
The C8051F581-IQ is appropriate for a compact acquisition panel that must measure several analog channels and forward results to a host computer. Its conversion capability of up to 200 ksps provides a practical balance between acquisition rate and processing load, while the 50 MHz core executes averaging, scaling, and status formatting. The two UART channels can separate host communication from equipment messaging, and SPI supports higher-speed converters or memories. With 128 KB of flash and 8 KB of RAM, the device can implement calibration tables and short-term history buffers in a single 48-TQFP controller.
Được đề xuất
Actuator and Motor-Control Node
The C8051F581-IQ can control a small actuator or motor subsystem where deterministic digital I/O, analog monitoring, and serial diagnostics are required. Its 50 MIPS execution rate supports current-loop or position-control tasks, fault handling, and communications concurrently. The integrated ADC can monitor feedback signals such as position, temperature, or supply voltage, while programmable gain helps condition lower-amplitude sensor outputs. The 48-TQFP package reduces board area in distributed control networks, and the flash memory enables field-updatable control parameters. Confirm pin multiplexing and peripheral assignments in the manufacturer datasheet before assigning motor-control outputs.
Được đề xuất
LIN Gateway and Body-Network Interface
The C8051F581-IQ is suitable for a small gateway that manages point-of-control and body-network communications in a space-constrained module. Two UART channels and support for SPI and I2C enable the controller to bridge several local buses and service gateway protocol stacks. Its 128 KB of flash is useful for routing tables, diagnostics, and network configuration, while the 50 MHz core leaves processing capacity for message validation and higher-level logic. The C8051F580 is often preferred when integrated CAN 2.0B and LIN 2.1 controllers are required, so confirm the exact bus resources on the C8051F581 before finalizing the network architecture.
Được đề xuất
Embedded Industrial Sensor Interface
The C8051F581-IQ works well as the interface controller for a modular industrial sensor that converts transducer signals into digital measurements. The 12-bit ADC, programmable-gain stage, and data-dependent windowed interrupt generator support repeatable acquisition and event-driven firmware. SPI or I2C connects local sensors and configuration devices, while UART provides a service or diagnostic channel. At 128 KB of flash and 8 KB of RAM, the MCU can maintain calibration coefficients, filtering routines, and communication buffers without an external memory device. Its 48-TQFP footprint supports compact DIN-rail or equipment-mounted assemblies where every millimeter of board area matters.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho C8051F581-IQ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | C8051F586-IQ | C8051F580-IQ | C8051F582-IQ | C8051F583-IQ |
|---|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 48-TQFP (7x7) | 48-TQFP (7x7) | 48-TQFP (7x7) | 48-TQFP (7x7) | 48-TQFP (7x7) |
| Core Architecture | 8051-compatible CISC | 8051-compatible CISC | 8051-compatible CISC | 8051-compatible CISC | 8051-compatible CISC |
| Automotive and Industrial Positioning | Automotive and industrial | C8051F58x family | Automotive and industrial | C8051F58x family | C8051F58x family |
Bảo phân biệt quan trọng
- High-speed 8-bit processing in a compact package (vsC8051F580-IQ)
- Distinct bus-controller configuration for body-network designs (vsC8051F580-IQ)
- Integrated multi-protocol connectivity (vsC8051F586-IQ)
- Mixed-signal conversion performance (vsC8051F582-IQ)
Ghi chú thiết kế
Route the 48-TQFP controller on a minimum two-layer board with a continuous ground plane beneath the device, and place the supply bypass capacitors immediately adjacent to their respective power pins. Separate analog inputs from switching-node copper and keep the analog ground return toward the converter rather than through high-current motor or relay paths. Follow the manufacturer package drawing for exposed-pad or thermal-via requirements specific to the selected package variant.
Treat UART, SPI, and I2C traces as controlled-length interfaces rather than general-purpose routing. Provide a defined reference ground, avoid routing communications lines parallel to high-current outputs, and reserve a quiet return path beneath serial pairs when practical. Because the MCU combines high-rate conversion, communications, and digital control, analog and digital return currents should remain separated until they join at the planned analog reference point.
Do not assume every C8051F58x variant provides the same bus controllers, memory size, or pin multiplexing. In particular, the C8051F580 includes CAN 2.0B and LIN 2.1 resources that differ from the C8051F581 configuration. Also do not substitute the 48-QFN C8051F581-IMR for the 48-TQFP C8051F581-IQ. Check the device-specific pin table, clock requirements, and peripheral matrix before releasing the PCB or firmware.
Design the regulator and decoupling network around the selected 2.5 V, 3.3 V, or 5 V operating point. Validate startup, brownout behavior, and analog-reference settling before acquiring critical sensor readings. If the ADC is used for safety-critical or high-accuracy measurements, add the manufacturer-recommended analog bypass network and allow the internal reference and conversion subsystem to stabilize before sampling.
Thông tin tuân thủ
The part is positioned as an automotive and industrial MCU, but an explicit RoHS, REACH, AEC-Q100 grade, lead-free declaration, or halogen-free declaration was not identified. Confirm the current declarations with the manufacturer before production release.