EFM32G880F32-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs
MPN: EFM32G880F32-QFP100 ✓ Hoạt độngEFM32G880F32-QFP100 Tóm tắt
An ARM Cortex-M3 microcontroller is a 32-bit embedded processor designed for real-time control, sensor handling, communications, and human-interface applications. Within the product hierarchy, the EFM32G880 belongs to the Gecko MCU family and combines a general-purpose processor with low-power operating techniques, fast wake-up behavior, and energy-saving modes for energy-sensitive equipment.
The EFM32G880F32-QFP100 integrates 32 kB Flash, 8 kB RAM, 86 digital I/O pins, and three 16-bit timers. Its operating voltage range is 1.98 V to 3.8 V, while its maximum CPU frequency is 32 MHz. The manufacturer identifies the device for applications requiring secure data processing, AES encryption support, and graphics or LCD-oriented functionality, including support for a 4 x 40 LCD.
The Gecko low-power architecture is central to the device's value in embedded systems. Low-energy techniques and energy-saving modes allow the MCU to reduce active consumption during idle intervals, while fast wake-up behavior supports responsive event-driven designs. Developers can use the Cortex-M3 instruction set and integrated peripherals to consolidate control, communications, display handling, and data acquisition onto one device rather than distributing those tasks among multiple discrete components.
Typical applications include industrial sensor nodes, building automation controllers, portable measurement instruments, medical monitoring equipment, graphical user-interface controllers, and connected energy-management products. The 86 digital I/O pins are especially useful where an application must connect discrete sensors, actuators, buttons, indicators, or external interface devices while preserving a high pin count for direct PCB routing.
When laying out a board, assign all 100 package pins by consulting the manufacturer pin-description table and account for the exposed supply, ground, debugging, and peripheral functions shown there. Confirm operating conditions, voltage rails, and peripheral multiplexing against the manufacturer datasheet before finalizing the schematic and footprint. The 100-LQFP package supports a 14 mm x 14 mm land pattern but requires careful assembly planning because of its fine pitch.
This page combines manufacturer specifications, sourced product information, application guidance, pin-package considerations, and engineering-focused comparisons to support component selection and PCB planning. It also identifies the limitations of available drop-in alternatives so engineers can distinguish electrically similar replacements from verified, package-compatible choices.
Bộ thay thế dễ dàng lắp đặt cho EFM32G880F32-QFP100 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
EFM32G880F32-QFP100T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EFM32G880F64
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EFM32G880F32G-E-QFP100R
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EFM32G880F32-QFP100 Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit ARM Cortex-M3 Gecko microcontroller |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 32 kB |
| RAM | 8 kB |
| Digital I/O Pins | 86 pins |
| Timers | 3 x 16-bit timers |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Core Architecture | ARM Cortex-M3, 32-bit |
| Hộp | 100-LQFP (14 mm x 14 mm) |
| Kiểu lắp đặt | Surface mount |
| LCD Support | 4 x 40 LCD |
| Encryption Support | AES encryption |
| Program Memory Organization | 32K x 8 |
| Series | EFM32 Gecko |
| Interface and Security Features | AES encryption and graphical or LCD application support |
Hướng dẫn cấu hình chân EFM32G880F32-QFP100 100-lqfp (14 mm x 14 mm)
Cấu hình chân cho EFM32G880F32-QFP100 (100-lqfp (14 mm x 14 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho EFM32G880F32-QFP100.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
EFM32G880F32-QFP100 phù hợp cho 6 Áp dụngs: Industrial Sensor and Control Node, Building Automation Controller, Portable Medical Monitoring Device, LCD Human-Interface Controller, Low-Power Data Acquisition Unit, Energy Metering and Smart Grid Interface.
Industrial Sensor and Control Node
The EFM32G880F32-QFP100 fits distributed industrial sensor nodes because its 86 digital I/O pins can connect discrete inputs, output drivers, status indicators, and local control signals without requiring a large companion I/O device. The 32 MHz ARM Cortex-M3 core supports responsive acquisition and control tasks, while three 16-bit timers provide timing resources for pulse measurement, periodic sampling, or motor and actuator timing. Its 1.98 V to 3.8 V operating range supports low-voltage industrial rails. Use the low-power Gecko modes for duty-cycled installations, but verify temperature range, isolation requirements, EMC expectations, and long-term availability for the deployed environment.
Được đề xuất
Building Automation Controller
The EFM32G880F32-QFP100 is suitable for building automation equipment that coordinates lighting inputs, occupancy sensors, relays, and communications in a centralized controller. Its 86 digital I/O pins provide broad local connectivity, while the 32-bit Cortex-M3 core can process protocol stacks and maintain multiple control tasks. Three 16-bit timers support timing functions associated with delays, pulse detection, and periodic system updates. The Gecko architecture's fast wake-up and energy-saving modes benefit controllers that spend substantial time idle. Confirm the required bus interfaces, isolation boundaries, supply regulation, and safety margins in the manufacturer documentation before integrating it with mains-connected equipment.
Được đề xuất
Portable Medical Monitoring Device
The EFM32G880F32-QFP100 can support portable monitoring equipment that combines sensor acquisition, local indication, user input, and data processing. Its 32-bit Cortex-M3 core handles control logic efficiently, and the 86 digital I/O pins are useful for sensor selection lines, buttons, alarms, and display connections. The low-power Gecko platform helps reduce energy use between measurements, enabling battery-oriented designs when the duty cycle permits it. AES encryption support may assist protected data workflows. Medical deployment still requires validation of the exact ordering variant's temperature range, applicable quality documentation, electrical safety, and patient-contact isolation requirements; the MCU qualification alone does not certify the finished medical system.
Được đề xuất
LCD Human-Interface Controller
The EFM32G880F32-QFP100 is a natural fit for LCD-equipped controls because Silicon Labs identifies support for a 4 x 40 LCD alongside the 32-bit Cortex-M3 core. The MCU can consolidate display updates, front-panel buttons, status LEDs, and local control logic in one package. Its 86 digital I/O pins leave ample interface capacity for switch inputs, relay outputs, and communications, while the 32 kB Flash and 8 kB RAM provide space for the interface firmware. Validate LCD segment mapping, contrast voltage, update timing, and multiplexing settings in the manufacturer reference manual. Check boot behavior and watchdog requirements so the display recovers predictably after power interruptions.
Được đề xuất
Low-Power Data Acquisition Unit
The EFM32G880F32-QFP100 fits low-power data-acquisition units that need flexible digital signal routing, timer-based sampling, and local control. The 86 digital I/O pins allow multiple sensor channels, multiplexers, and status signals to be connected directly, while three 16-bit timers can establish repeatable acquisition intervals or measure input pulses. At a maximum CPU frequency of 32 MHz, the Cortex-M3 core has ample capacity for filtering and data preparation before buffered transmission. Energy-saving modes and fast wake-up are valuable when the instrument operates mostly between samples. Use the datasheet to size external input networks, choose the supply architecture, and verify ADC requirements because the target MPN is primarily a general-purpose MCU.
Được đề xuất
Energy Metering and Smart Grid Interface
The EFM32G880F32-QFP100 is appropriate for energy-metering front ends that combine pulse counting, status detection, local calibration, and communication control. Its three 16-bit timers can support metering pulse capture, and the 86 digital I/O pins can manage tamper inputs, relay controls, indicators, and isolated interface signals. The 32-bit Cortex-M3 core can run the main control loop, while Gecko energy-saving modes reduce consumption during long idle intervals. The 1.98 V to 3.8 V supply range allows operation from a suitably regulated low-voltage rail. Verify metering accuracy, isolation, safety standards, communications timing, and EMC performance against the finished instrument requirements before production use.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EFM32G880F32-QFP100 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EFM32G880F32-QFP100T | EFM32G880F64 | EFM32G880F32G-E-QFP100R |
|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 100-LQFP (14x14) | 100-LQFP - same package | 100-LQFP - same package | 100-LQFP - same package |
| CPU Core | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit | ARM Cortex-M3, 32-bit |
| Maximum Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 32 kB | 32 kB | 64 kB | 32 kB |
| Timers | 3 x 16-bit timers | 3 x 16-bit timers | 3 x 16-bit timers | 3 x 16-bit timers |
| Supply Voltage Range | 1.98 V to 3.8 V | 1.98 V to 3.8 V | 1.98 V to 3.8 V | 1.98 V to 3.8 V |
| Encryption and Display Support | AES encryption and 4 x 40 LCD support | AES encryption and 4 x 40 LCD support | AES encryption and 4 x 40 LCD support | AES encryption and 4 x 40 LCD support |
Bảo phân biệt quan trọng
- Lower on-device memory than the F64 family member (vsEFM32G880F64)
- Closest ordering match in the documented comparison (vsEFM32G880F32-QFP100T)
- Same 100-LQFP footprint and 32 kB memory family (vsEFM32G880F32G-E-QFP100R)
Ghi chú thiết kế
Use the manufacturer 100-LQFP land pattern and pin table as the authoritative PCB references. Place the required supply decoupling capacitors adjacent to the corresponding power pins and route them over a continuous ground plane. With 86 digital I/O pins and a 14 mm x 14 mm footprint, preserve access for fine-pitch assembly inspection and avoid routing high-speed or switching signals beneath sensitive analog inputs.
Design the supply around the documented 1.98 V to 3.8 V operating range rather than treating it as the absolute-maximum limit. Confirm regulator headroom, startup sequencing, and voltage ramp behavior against the application. The MCU supports energy-saving modes, so test whether peripherals can remain powered while the core sleeps and verify that wake-up sources remain functional across the full supply range.
Do not assume that every EFM32G880 orderable suffix is interchangeable. Confirm the F32 memory capacity, 100-LQFP pin arrangement, temperature grade, environmental ordering suffix, and assembly format separately. A footprint match alone does not guarantee firmware compatibility because memory size, peripheral configuration, ordering options, and qualification requirements can differ.
Thông tin tuân thủ
No explicit compliance declaration was identified for the exact MPN. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status with Silicon Labs or the authorized supply source for the ordered configuration.