EFM32WG232F64-QFP64 - 48MHz Cortex-M4F MCU | Silicon Labs
MPN: EFM32WG232F64-QFP64 ✓ Hoạt độngEFM32WG232F64-QFP64 Tóm tắt
A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interfaces into one device. The EFM32WG232F64-QFP64 belongs to the Wonder Gecko family and is designed for compact, low-power embedded systems. Its architecture supports real-time control, communications, sensor acquisition, and human-interface functions without requiring a separate processor and supporting digital components.
Key features include a 48 MHz ARM Cortex-M4F core, full DSP instruction support, a single-precision floating-point unit, and 64 KB of flash. AES acceleration supports efficient cryptographic operations. The specified 1.98 V to 3.8 V operating-supply range accommodates low-voltage 3.3 V systems, while configurable peripheral input and output locations help designers place communication and control functions on available pins.
The Cortex-M4F architecture combines a 32-bit ARM instruction set with deterministic exception handling and DSP capabilities. At clock speeds up to 48 MHz, the device provides more computational headroom than slower general-purpose microcontrollers while retaining an event-driven operating model suited to battery-operated equipment. The floating-point unit accelerates common signal-processing operations without requiring software emulation.
Typical uses include industrial sensor nodes, connected measurement equipment, building controls, compact motor controllers, low-power IoT terminals, and handheld instruments. Its 64 KB flash capacity is appropriate for moderate firmware workloads, while the AES peripheral is useful in designs that require encrypted data transfer or protected firmware-related communications. Board design must still confirm memory, peripheral, and security requirements against the complete device documentation.
For a new layout, place decoupling capacitors close to the supply and ground pins, route sensitive signals away from fast-switching nodes, and preserve the manufacturer’s recommended exposed-pad connection and thermal land pattern. Because the orderable marking includes QFP64 while the manufacturer listing identifies a 64-QFN 9x9 mm package, verify the physical symbol, pin table, and land pattern before fabrication rather than inferring geometry from the suffix alone.
This product record combines exact manufacturer and distributor attributes, supply-voltage and memory details, package information, application guidance, and practical design considerations. It also separates confirmed characteristics from parameters that require a direct datasheet check, helping engineers plan sourcing and PCB review with fewer specification assumptions.
Bộ thay thế dễ dàng lắp đặt cho EFM32WG232F64-QFP64 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếEFM32WG232F64-QFP64 Tỷ lệ tối đa & tính chất điện
| Device Type | 32-bit microcontroller |
| Processor Core | ARM Cortex-M4F |
| Architecture | ARM 32-bit |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 64 KB |
| Flash Organization | 64K x 8 bits |
| DSP Support | Full DSP instruction set |
| Floating-Point Unit | Single-precision floating-point unit |
| Security Accelerator | AES hardware accelerator |
| Điện áp cung cấp hoạt động | 1.98 V to 3.8 V |
| Manufacturer Package | 64-QFN (9x9 mm) |
| Product Family | Wonder Gecko |
| Peripheral Input and Output | Configurable peripheral I/O locations |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân EFM32WG232F64-QFP64 64-qfn (9x9 mm)
Cấu hình chân cho EFM32WG232F64-QFP64 (64-qfn (9x9 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho EFM32WG232F64-QFP64.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
EFM32WG232F64-QFP64 phù hợp cho 6 Áp dụngs: Industrial Sensor Nodes, Connected Measurement Equipment, Building Control Modules, Compact Motor Control, Battery-Powered IoT Terminals, Handheld Test Instruments.
Industrial Sensor Nodes
The EFM32WG232F64-QFP64 fits compact industrial sensor nodes that combine periodic sensing, local filtering, and secure communications. Its 48 MHz ARM Cortex-M4F core includes full DSP instructions and a floating-point unit, allowing common filtering and scaling operations to run locally without an external processor. The 64 KB flash supports moderate protocol and control firmware, while the hardware AES accelerator can offload encrypted communication. The 1.98 V to 3.8 V operating range is suitable for 3.3 V sensor platforms. Confirm the device’s low-power mode behavior against the node’s duty cycle because average battery consumption will also depend on the radio, sensor, and external circuitry.
Connected Measurement Equipment
The EFM32WG232F64-QFP64 is well suited to connected measurement equipment that must acquire sensor data, run real-time calculations, and communicate with a host. At up to 48 MHz, the Cortex-M4F core provides deterministic processing for filtering, calibration, and control functions. Its full DSP instruction set and single-precision floating-point unit accelerate common numeric operations, while 64 KB flash accommodates a focused firmware image. AES hardware support can accelerate protected data transfer. The 64-QFN 9x9 mm package preserves board area in compact instruments, but the physical footprint, exposed-pad connection, and pin assignments must be checked against the manufacturer drawing before layout release.
Building Control Modules
The EFM32WG232F64-QFP64 can serve as the local controller in building-control modules for lighting, occupancy, environmental sensing, and actuator interfaces. The 48 MHz Cortex-M4F processor handles protocol tasks and control logic, while configurable peripheral I/O locations help route communication and timing functions among available pins. Its 64 KB flash is appropriate for a focused embedded application rather than a large graphical user interface. The 1.98 V to 3.8 V supply range supports low-voltage system rails. For motor, relay, or mains-connected equipment, validate isolation, transient protection, grounding, and thermal margins independently because those protections are not inherent to the microcontroller package.
Compact Motor Control
The EFM32WG232F64-QFP64 is applicable to compact motor-control subsystems where fast control-loop execution, compact size, and secure parameter handling are important. The Cortex-M4F core runs at up to 48 MHz and provides full DSP instructions plus a floating-point unit for transforms and control calculations. AES hardware acceleration can support protected configuration or communications. With 64 KB flash, the device targets embedded control firmware rather than large data logging. The 64-QFN 9x9 mm package helps minimize board area, but power-stage design, current sensing, protection, and thermal performance depend on the external motor electronics and must be evaluated as a complete system.
Battery-Powered IoT Terminals
The EFM32WG232F64-QFP64 is a candidate for battery-powered IoT terminals that need more local computation than a basic sensor interface but must remain compact. Its 48 MHz Cortex-M4F core can process acquired data before transmission, while AES hardware acceleration supports encrypted communication without using the core for every cryptographic operation. The 64 KB flash provides space for networking, device management, and application logic, and configurable peripheral I/O locations assist compact board routing. Actual battery life depends on the selected sleep states, radio duty cycle, sensor load, and regulator efficiency. Validate sleep-mode current and wake-up timing on the final hardware rather than estimating them from processor frequency alone.
Handheld Test Instruments
The EFM32WG232F64-QFP64 fits handheld and portable test instruments where signal processing, responsive control, and compact packaging are important. The single-precision floating-point unit and full DSP instruction set support common filtering and numerical routines at up to 48 MHz, reducing dependence on external computation. Its 64 KB flash is suited to compact instrument firmware, while AES hardware acceleration can protect stored or transmitted data. The 64-QFN 9x9 mm package supports space-constrained handheld layouts. USB, display, keypad, and analog interface requirements must be checked individually against the device peripheral set and pin map, along with battery power consumption and thermal behavior during sustained operation.
Dữ liệu tham khảo kỹ thuật cho EFM32WG232F64-QFP64 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Package | 64-QFN (9x9 mm) |
| Brand | Silicon Labs |
| Processor Core | ARM Cortex-M4F |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 64 KB |
| Operating Supply Voltage | 1.98 V to 3.8 V |
| DSP Instruction Support | Full DSP instruction set |
| Floating-Point Support | Single-precision floating-point unit |
| Security Accelerator | AES hardware accelerator |
| Product Family | Wonder Gecko |
Ghi chú thiết kế
Confirm the physical package against the Silicon Labs package drawing before releasing the PCB. The orderable name contains QFP64, while the manufacturer listing identifies a 64-QFN 9x9 mm package. Create the schematic symbol and land pattern from the manufacturer pin table, verify pin 1 orientation, and follow the prescribed exposed-pad and thermal-via layout rather than selecting a footprint solely from the order-code suffix.
Place the recommended bypass capacitors close to the device supply and ground pins and keep the supply-loop area as small as practical. The device operates from 1.98 V to 3.8 V, so validate startup, brownout behavior, and rail tolerance across the complete system supply range. Use the manufacturer’s recommended capacitor values and ESR requirements because generic decoupling assumptions may not preserve oscillator, ADC, or digital timing performance.
Separate clock, sensor, and communication signals from high-current switching nodes and preserve a continuous ground reference beneath the device footprint. Route sensitive analog inputs away from digital return currents and the exposed-pad connection. If the 64-QFN package requires an exposed thermal pad, connect it according to the manufacturer drawing and evaluate the pad’s effect on return paths as well as heat removal.
Do not treat the 64 KB flash figure as the complete memory budget without checking RAM and peripheral requirements in the device documentation. The Cortex-M4F core, AES accelerator, communications peripherals, firmware stack, and application code must all fit the device configuration. Similarly, confirm the exact operating-temperature grade, qualification status, and package dimensions before committing a design to industrial or automotive environments.
Thông tin tuân thủ
The current manufacturer and distributor records do not provide explicit compliance declarations for this exact orderable device. Request the relevant Silicon Labs product declarations before using the component in a regulated production program.