THÔNG BÁO MUA LẦN CUỐI: EPF10K30EQI208-3 sắp tới cuối cuộc sống. Ngày đặt hàng cuối cùng: Liên hệ với chúng tôi. Xem các bộ phận thay thế có sẵn →
EPF10K30EQI208-3 - FLEX 10KE FPGA, 30K Gates, 208-Pin QFP | Intel EPF10K30EQI208-3 bởi Intel - thành phần điện tử
Intel

EPF10K30EQI208-3 - FLEX 10KE FPGA, 30K Gates, 208-Pin QFP | Intel

MPN: EPF10K30EQI208-3 ⚠ Lần mua cuối
2.5 V Vdss 208-BFQFP / Power-QFP (RQ208) Package 909.09 MHz Speed
Yêu cầu báo giá
MOQ: 1 |
Xem tài liệu kỹ thuật (PDF) Xem các bộ thay thế

EPF10K30EQI208-3 Tóm tắt

The Intel (formerly Altera) EPF10K30EQI208-3 is a FLEX 10KE family Field Programmable Gate Array delivering approximately 30,000 equivalent ASIC gates, 1,728 logic elements, and 24,576 RAM bits in a 208-pin Power-QFP (BFQFP, RQ208) package. It provides 147 user I/O pins, a 12.5 ns pin-to-pin propagation delay, and operates from a nominal 2.5 V core supply across the industrial -40C to +85C temperature range. The device is built on a 0.22 um CMOS SRAM process with embedded array architecture.

What is an FPGA? A Field Programmable Gate Array is a reprogrammable semiconductor device whose logic functionality is defined by user-loaded configuration bitstreams rather than hard-wired mask layers. FPGAs sit in the broader hierarchy programmable logic device (PLD) -> CPLD -> FPGA -> programmable SoC, and they integrate configurable logic blocks (LEs), embedded array blocks (EABs), programmable interconnect, and I/O elements on a single die. The FLEX 10KE family was Altera's second-generation embedded-array SRAM FPGA line, designed for moderate-density glue logic, bus interfacing, and small state-machine consolidation.

Key features include 1,728 logic elements (LEs), six Embedded Array Blocks providing 24,576 bits of synchronous dual-port RAM, MultiVolt I/O supporting 2.5 V, 3.3 V, and 5.0 V interfaces on the same die, in-system programmability via the serial passive or JTAG configuration chain, and four Low-Skew Clock networks. The on-chip EABs can be configured as 256x8, 512x4, 1024x2, or 2048x1 memory blocks and are also usable as product-term logic arrays for wide fan-in functions.

Technical depth: The FLEX 10KE architecture uses a continuous, segmented routing fabric with FastTrack Interconnect, allowing predictable timing closure for designs up to ~30K gates. The device supports IEEE 1149.1 boundary-scan test and 4 mA drive strength per I/O with slew-rate control. The -3 speed grade is the fastest commercial grade available for this family, optimizing for synchronous datapath throughput rather than area efficiency.

Typical applications for the EPF10K30EQI208-3 include telecom line-card glue logic, peripheral bus bridges (PCI to local bus), industrial motor-control and PLC interface boards, and legacy equipment retrofits. The 208-pin PQFP footprint also made the device common in 1990s-vintage networking and instrumentation gear that is now being redesigned for long-life-cycle support.

Design consideration: When designing with this part, ensure your configuration bitstream is stored in a compatible PROM (EPC2, EPC8, or EPC16) or loaded via JTAG at power-up, because the SRAM-based FLEX 10KE loses its configuration on every power-down. The MultiVolt I/O bank requires separate VCCIO rails for mixed-voltage interfacing; do not tie VCCIO directly to VCCINT.

This page synthesizes distributor pricing, drop-in alternative MPNs from the same Altera FLEX 10KE family, and practical design notes not consolidated in the original manufacturer datasheet, giving engineers a faster path to source this mature FPGA for new builds and legacy redesigns.

Bộ thay thế dễ dàng lắp đặt cho EPF10K30EQI208-3 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EPF10K30EQI208-3 (cùng hình factor và footprint) — khác nhau ở Process Technology, Package, Family, Operating Temperature, Propagation Delay.

Altera
Process Technology: 0.30 µm CMOS
Family: FLEX 10KA
Operating Temperature: -40 °C to +85 °C (Industrial)
So sánh với EPF10K30EQI208-3 →
Altera
Process Technology: 0.30 µm CMOS SRAM
Package: 208-BFQFP (PQFP, surface mount)
Family: FLEX-10KA
So sánh với EPF10K30EQI208-3 →
Intel
Process Technology: CMOS
Package: 208-PQFP (BFQFP)
Family: FLEX 10KE
So sánh với EPF10K30EQI208-3 →
Intel
Process Technology: 0.22 µm CMOS
Package: 208-pin PQFP (BFQFP, plastic)
Family: FLEX 10KE
So sánh với EPF10K30EQI208-3 →
Intel
Process Technology: 0.42 µm CMOS SRAM
Package: 208-PQFP (BFQFP)
Family: FLEX 10KE
So sánh với EPF10K30EQI208-3 →
Altera
Process Technology: 0.22 µm CMOS, SRAM-based
Package: 208-pin BFQFP / PQFP (gull-wing)
Family: FLEX 10KE
So sánh với EPF10K30EQI208-3 →

EPF10K30EQI208-2

✅ Drop-In
Intel
📦 208-BFQFP (RQ208)
FLEX 10KE · 1,728 · 216 · 30,000 · 119,000 · 24,576 · 147 · 208-PQFP (BFQFP)

Liên hệ để biết giá

Xem tài liệu →

EPF10K30EQI208-2N

✅ Drop-In
Altera
📦 208-BFQFP (RQ208)
FLEX 10KE · 1,728 · 30,000 · 147 · 24,576 · 216 · 6 · 0.22 µm CMOS, SRAM-based

Liên hệ để biết giá

Xem tài liệu →

EPF10K30AQI208-3N

✅ Drop-In
Altera
📦 208-BFQFP (RQ208)
FLEX-10KA · 1,728 · 30,000 · 12,288 bits (6 × 2,048 bits) · 216 · 147 · 208-BFQFP (PQFP, surface mount) · 3.3 V

Liên hệ để biết giá

Xem tài liệu →

EPF10K30AQI208-3

✅ Drop-In
Altera
📦 208-BFQFP (RQ208)
FLEX 10KA · 1,728 · 12,288 · 30,000 · 147 · 1,728 · 3.3 V · 0.30 µm CMOS

Liên hệ để biết giá

Xem tài liệu →

EPF10K30EQC208-3

✅ Drop-In
Intel
📦 208-BFQFP (RQ208)
FPGA (Field Programmable Gate Array) · FLEX 10KE · 1,728 · 30,000 · 24,576 · 12 · 246 · 208-PQFP (BFQFP)

Liên hệ để biết giá

Xem tài liệu →

EPF10K30EQC208-3N

✅ Drop-In
Intel
📦 208-BFQFP (RQ208)
FLEX 10KE · 1,728 · 30,000 · 24,576 · 216 · 147 · 200 MHz

Liên hệ để biết giá

Xem tài liệu →

EPF10K30EQI208-3 Tỷ lệ tối đa & tính chất điện

Series FLEX 10KE
Family FLEX 10KE (FLEX 10K Embedded Array)
Logic Elements 1,728
Equivalent Gates 30,000 (typical)
Embedded Array Blocks (EAB) 6
Total RAM Bits 24,576
User I/O 147
Total Inputs 151
Propagation Delay 12.5 ns
Tần số xung maksimum 909.09 MHz
Core Supply Voltage (VCCINT) 2.5 V
I/O Supply Voltage (VCCIO) 2.5 V / 3.3 V / 5.0 V (MultiVolt)
Nhiệt độ hoạt động -40C to +85C (Industrial)
Hộp 208-BFQFP / Power-QFP (RQ208)
Kiểu lắp đặt Surface Mount (Gull Wing)
Process Technology 0.22 um CMOS SRAM
Configuration SRAM, serial passive / JTAG
Trạng thái RoHS Compliant (Pb-free suffix variants available)

Cấu hình chân EPF10K30EQI208-3

Generic Component Pin Configuration Generic integrated-circuit pinout placeholder. Pin 1 indicated by dot; exact pin count and functions in the pin table below. 1 N 2 N-1 3 N-2 4 N-3 Pin Configuration See pin table below for pin functions Package-specific diagram not available
Chân 1 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 2 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 3 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 4 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 5 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 6 VCCIO1 — I/O supply voltage bank 1 (MultiVolt 2.5V/3.3V/5.0V)
Chân 7 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 8 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 9 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 10 GND — Ground
Chân 11 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 12 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 13 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 14 nCONFIG — Configuration control (active-low reset)
Chân 15 VCCINT — Core supply voltage 2.5V
Chân 16 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 17 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 18 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 19 GND — Ground
Chân 20 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 21 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 22 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 23 MSEL0 — Configuration mode select 0
Chân 24 MSEL1 — Configuration mode select 1
Chân 25 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 26 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 27 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 28 VCCIO1 — I/O supply voltage bank 1 (MultiVolt 2.5V/3.3V/5.0V)
Chân 29 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 30 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 31 I/O — User I/O (bank 1) - exact function depends on user configuration
Chân 32 GND — Ground
Chân 33 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 34 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 35 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 36 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 37 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 38 VCCIO2 — I/O supply voltage bank 2 (MultiVolt 2.5V/3.3V/5.0V)
Chân 39 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 40 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 41 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 42 GND — Ground
Chân 43 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 44 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 45 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 46 VCCINT — Core supply voltage 2.5V
Chân 47 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 48 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 49 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 50 GND — Ground
Chân 51 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 52 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 53 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 54 CLK0 — Dedicated clock input 0
Chân 55 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 56 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 57 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 58 VCCIO2 — I/O supply voltage bank 2 (MultiVolt 2.5V/3.3V/5.0V)
Chân 59 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 60 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 61 I/O — User I/O (bank 2) - exact function depends on user configuration
Chân 62 GND — Ground
Chân 63 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 64 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 65 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 66 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 67 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 68 VCCIO3 — I/O supply voltage bank 3 (MultiVolt 2.5V/3.3V/5.0V)
Chân 69 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 70 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 71 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 72 GND — Ground
Chân 73 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 74 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 75 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 76 VCCINT — Core supply voltage 2.5V
Chân 77 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 78 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 79 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 80 GND — Ground
Chân 81 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 82 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 83 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 84 CLK1 — Dedicated clock input 1
Chân 85 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 86 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 87 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 88 VCCIO3 — I/O supply voltage bank 3 (MultiVolt 2.5V/3.3V/5.0V)
Chân 89 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 90 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 91 I/O — User I/O (bank 3) - exact function depends on user configuration
Chân 92 GND — Ground
Chân 93 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 94 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 95 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 96 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 97 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 98 VCCIO4 — I/O supply voltage bank 4 (MultiVolt 2.5V/3.3V/5.0V)
Chân 99 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 100 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 101 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 102 GND — Ground
Chân 103 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 104 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 105 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 106 VCCINT — Core supply voltage 2.5V
Chân 107 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 108 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 109 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 110 GND — Ground
Chân 111 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 112 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 113 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 114 CLK2 — Dedicated clock input 2
Chân 115 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 116 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 117 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 118 VCCIO4 — I/O supply voltage bank 4 (MultiVolt 2.5V/3.3V/5.0V)
Chân 119 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 120 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 121 I/O — User I/O (bank 4) - exact function depends on user configuration
Chân 122 GND — Ground
Chân 123 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 124 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 125 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 126 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 127 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 128 VCCIO5 — I/O supply voltage bank 5 (MultiVolt 2.5V/3.3V/5.0V)
Chân 129 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 130 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 131 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 132 GND — Ground
Chân 133 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 134 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 135 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 136 VCCINT — Core supply voltage 2.5V
Chân 137 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 138 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 139 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 140 GND — Ground
Chân 141 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 142 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 143 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 144 CLK3 — Dedicated clock input 3
Chân 145 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 146 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 147 I/O — User I/O (bank 5) - exact function depends on user configuration
Chân 148 VCCIO5 — I/O supply voltage bank 5 (MultiVolt 2.5V/3.3V/5.0V)
Chân 149 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 150 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 151 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 152 GND — Ground
Chân 153 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 154 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 155 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 156 VCCINT — Core supply voltage 2.5V
Chân 157 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 158 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 159 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 160 GND — Ground
Chân 161 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 162 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 163 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 164 nSTATUS — Configuration status (active-low)
Chân 165 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 166 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 167 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 168 VCCIO6 — I/O supply voltage bank 6 (MultiVolt 2.5V/3.3V/5.0V)
Chân 169 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 170 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 171 I/O — User I/O (bank 6) - exact function depends on user configuration
Chân 172 GND — Ground
Chân 173 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 174 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 175 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 176 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 177 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 178 VCCIO7 — I/O supply voltage bank 7 (MultiVolt 2.5V/3.3V/5.0V)
Chân 179 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 180 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 181 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 182 GND — Ground
Chân 183 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 184 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 185 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 186 VCCINT — Core supply voltage 2.5V
Chân 187 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 188 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 189 I/O — User I/O (bank 7) - exact function depends on user configuration
Chân 190 GND — Ground
Chân 191 I/O — User I/O (bank 8) - exact function depends on user configuration
Chân 192 I/O — User I/O (bank 8) - exact function depends on user configuration
Chân 193 I/O — User I/O (bank 8) - exact function depends on user configuration
Chân 194 CONF_DONE — Configuration complete (open-drain, pull-up required)
Chân 195 DCLK — Configuration clock input
Chân 196 I/O — User I/O (bank 8) - exact function depends on user configuration
Chân 197 I/O — User I/O (bank 8) - exact function depends on user configuration
Chân 198 I/O — User I/O (bank 8) - exact function depends on user configuration
Chân 199 GND — Ground
Chân 200 I/O — User I/O (bank 8) - exact function depends on user configuration
Chân 201 I/O — User I/O (bank 8) - exact function depends on user configuration
Chân 202 I/O — User I/O (bank 8) - exact function depends on user configuration
Chân 203 TCK — JTAG test clock
Chân 204 TMS — JTAG test mode select
Chân 205 TDI — JTAG test data in
Chân 206 TDO — JTAG test data out
Chân 207 I/O — User I/O (bank 8) - exact function depends on user configuration
Chân 208 I/O — User I/O (bank 8) - exact function depends on user configuration

Ứng dụng tiêu biểu

EPF10K30EQI208-3 phù hợp cho 6 Áp dụngs: Telecom Line-Card Glue Logic, Peripheral Bus Bridge (PCI / ISA to Local Bus), Industrial Motor-Control and PLC Interface, Legacy Test and Measurement Instrumentation, Aerospace and Defense Avionics Retrofit, Networking Router/Switch Line-Card Aggregation.

🌐

Telecom Line-Card Glue Logic

The EPF10K30EQI208-3's 1,728 logic elements and 147 user I/O pins make it well suited for telecom line-card glue-logic consolidation, where it can replace multiple discrete PAL/GAL devices with a single reprogrammable part. Its 12.5 ns propagation delay in the -3 speed grade comfortably meets T1/E1 framer interface timing. The embedded 24,576-bit RAM array is sufficient to implement small FIFO buffers, look-up tables, and protocol-state machines used in channel-associated signalling. MultiVolt I/O allows direct interface to 3.3 V and 5.0 V framers without level shifters. Industrial temperature grading and surface-mount PQFP packaging suit central-office equipment that must operate 24/7 for decades.

Được đề xuất

EPF10K30EQI208-2 · Intel EPC2LC20 · Altera
🖥️

Peripheral Bus Bridge (PCI / ISA to Local Bus)

The EPF10K30EQI208-3 is widely deployed as a peripheral bus bridge between legacy PCI or ISA buses and proprietary local buses on industrial motherboards. The 147 I/Os are sufficient to implement full 32-bit PCI master/target interfaces with parity, while the 6 EABs provide 24Kbits of dual-port RAM for transaction buffering. The 12.5 ns propagation delay enables 33 MHz PCI operation in the -3 grade. Embedded array architecture allows the same silicon to be reconfigured for different target bus protocols via bitstream swap. This application benefits from FLEX 10KE's robust MultiVolt I/O, which can mix 5 V PCI signalling with 3.3 V local-bus logic on the same die.

Được đề xuất

EPF10K30EQC208-3 · Intel EPC8QC100 · Altera
🏭

Industrial Motor-Control and PLC Interface

The EPF10K30EQI208-3's industrial temperature rating (-40C to +85C) and robust 208-PQFP package make it suitable for industrial motor-control and PLC interface boards. With 1,728 LEs, it can implement multi-axis PWM generators, quadrature decoder logic, encoder-interface state machines, and CAN/RS-485 bus bridges simultaneously. The 24Kbit embedded RAM supports capture buffers and trajectory look-up tables for servo loops. The 147 I/O pins easily accommodate multi-axis encoder inputs plus drive-enable outputs. SRAM-based configuration allows field reconfiguration for firmware upgrades over JTAG without removing the board from service.

Được đề xuất

EPF10K30EQI208-2N · Altera EPC16UC88 · Altera
🔧

Legacy Test and Measurement Instrumentation

In legacy test and measurement instruments such as bench-top oscilloscopes, logic analyzers, and protocol analyzers, the EPF10K30EQI208-3 serves as the central pattern-generator and timing-controller. Its 12.5 ns propagation delay and 909 MHz internal toggle rate allow direct synthesis of 40 MHz clock patterns and complex stimulus sequences. The 6 embedded array blocks provide 24Kbits of capture memory for logic-analyzer front-ends. The 208-PQFP package is easy to hand-rework on older through-hole-and-SMT-mix assemblies, simplifying field service. Long product life cycles in the T&M market (often 10-20 years) align with the FLEX 10KE family's mature-node reliability profile.

Được đề xuất

EPF10K30EQI208-3 · Intel EPC2LC20 · Altera
✈️

Aerospace and Defense Avionics Retrofit

The EPF10K30EQI208-3 is found in aerospace and defense avionics retrofit programs, where its industrial temperature range and MIL-STD-883 screening options make it suitable for harsh-environment cockpit and mission-computer upgrades. With 1,728 LEs, it can implement ARINC 429 / MIL-STD-1553 bus interfaces, discrete I/O expansion, and timing-synchronization logic. The 147 I/O pins handle multiple serial databuses plus parallel avionics discretes in a single device. The 208-PQFP package is mechanically robust and compatible with through-hole-style rework tools used in depot-level maintenance. Legacy long-lifecycle programs that cannot migrate to RoHS-only parts may continue to specify this device from LTB stock.

Được đề xuất

EPF10K30EQI208-2N · Altera EPC8QC100 · Altera
🌐

Networking Router/Switch Line-Card Aggregation

In legacy networking line cards, the EPF10K30EQI208-3 is commonly deployed as a packet-classification and queue-management co-processor alongside a network processor. Its 147 I/Os are sufficient to expose multiple SPI/UART/I2C management interfaces plus an 8-bit UTOPIA/POSPHY-style fabric interface. The 24Kbit EAB RAM supports small CAM emulations and statistics counters. The 12.5 ns propagation delay in -3 speed grade handles 50 MHz fabric-side clocks with comfortable margin. MultiVolt I/O lets the same device interface to 5 V legacy transceivers and 3.3 V ASICs without external level shifters. SRAM-based configuration enables per-linecard personality via factory-loaded bitstreams.

Được đề xuất

EPF10K30EQI208-2 · Intel EPC16UC88 · Altera

Tóm tắt các sản phẩm được đề xuất

EPF10K30EQI208-2 Intel Được sử dụng trong: Telecom Line-Card Glue Logic, Networking Router/Switch Line-Card Aggregation EPC2LC20 Altera Được sử dụng trong: Telecom Line-Card Glue Logic, Legacy Test and Measurement Instrumentation EPF10K30EQC208-3 Intel Được sử dụng trong: Peripheral Bus Bridge (PCI / ISA to Local Bus) EPC8QC100 Altera Được sử dụng trong: Peripheral Bus Bridge (PCI / ISA to Local Bus), Aerospace and Defense Avionics Retrofit EPF10K30EQI208-2N Altera Được sử dụng trong: Industrial Motor-Control and PLC Interface, Aerospace and Defense Avionics Retrofit EPC16UC88 Altera Được sử dụng trong: Industrial Motor-Control and PLC Interface, Networking Router/Switch Line-Card Aggregation EPF10K30EQI208-3 Intel Được sử dụng trong: Legacy Test and Measurement Instrumentation
What is the logic capacity of EPF10K30EQI208-3?
The EPF10K30EQI208-3 delivers approximately 30,000 equivalent ASIC gates organized as 1,728 logic elements (LEs), with six Embedded Array Blocks (EABs) providing 24,576 bits of synchronous dual-port RAM. This places it in the moderate-density tier of the Altera FLEX 10KE family. According to the Altera FLEX 10KE datasheet, the device targets glue-logic consolidation, peripheral bridging, and small state-machine integration rather than high-density datapath designs.
What package does the EPF10K30EQI208-3 use?
The EPF10K30EQI208-3 ships in a 208-pin Power-QFP package (BFQFP / RQ208) with gull-wing surface-mount leads. Pin 1 is located at the corner marked by the dot. According to the FLEX 10KE datasheet, the 208-PQFP variant exposes 147 user I/O pins, leaving the remaining pins for JTAG, configuration, power, and ground. The package is now considered legacy footprint and is being phased out across most distributors.
Is the EPF10K30EQI208-3 still in production?
The EPF10K30EQI208-3 is currently classified as Last Time Buy (LTB) by Intel PSG, with new orders accepted only until the published LTB date and final deliveries scheduled thereafter. The underlying FLEX 10KE family is part of Intel's mature-node FPGA portfolio that has been progressively superseded by Cyclone, MAX, and Agilex device families. Existing designs should plan a migration path before the LTB window closes.
What is the difference between EPF10K30EQI208-3 and EPF10K30EQC208-3?
The EPF10K30EQI208-3 is the industrial-temperature (-40C to +85C) variant in a 208-pin Industrial-PQFP, while the EPF10K30EQC208-3 is the commercial-temperature (0C to +70C) variant in a 208-pin Commercial-PQFP. Both share the same FLEX 10KE silicon die and 30K-gate capacity. The EQI vs EQC suffix encodes both temperature grade and speed grade; the 'I' suffix denotes industrial and 'C' denotes commercial.
What is the propagation delay of EPF10K30EQI208-3?
The EPF10K30EQI208-3 is rated at 12.5 ns pin-to-pin propagation delay in its -3 speed grade, which is the fastest speed grade offered for this part. Maximum toggle frequency is 909.09 MHz for internal logic. Speed grades of -2 and -1 are also available in the FLEX 10KE family, with progressively longer propagation delays of approximately 15 ns and 20 ns respectively. The -3 grade optimizes synchronous datapath throughput at the cost of higher dynamic power.
How do you configure the EPF10K30EQI208-3 at power-up?
The EPF10K30EQI208-3 is SRAM-based and must be configured at every power-on via the dedicated serial passive configuration chain or the JTAG (IEEE 1149.1) interface. According to Altera's configuration handbook, designers typically pair this device with an EPC2, EPC8, or EPC16 configuration PROM, or load the bitstream from a microcontroller through JTAG. Power-on reset timing must satisfy the 2.5 V VCCINT rise-time requirement before configuration begins.
Can EPF10K30EQI208-3 be replaced by a modern Altera/Intel FPGA?
Drop-in pin-compatible replacements within the FLEX 10KE family are limited, but functionally-equivalent modern replacements exist in the Intel Cyclone series. Cyclone IV EP4CE30 in F256 or similar BGA packages provides approximately the same LE count and more on-chip resources, but requires a PCB re-layout because the 208-PQFP footprint is not preserved. Engineers should treat this as a board redesign, not a drop-in swap. For true pin compatibility within the 208-PQFP, alternative FLEX 10KE speed-grade variants remain the only practical option.
What is the best drop-in replacement for EPF10K30EQI208-3?
Within the 208-pin PQFP footprint, the closest drop-in replacements are same-package FLEX 10KE speed-grade and temperature-grade variants such as EPF10K30EQI208-2 and EPF10K30EQI208-1. These share the identical die and pinout but trade off propagation delay for cost. Cross-brand pin-compatible replacements in the same footprint do not exist, because no other vendor replicated the FLEX 10KE 208-PQFP pinout; modern pin-compatible alternatives require PCB rework.
What is the price of EPF10K30EQI208-3 in 2026?
As of September 2026, EPF10K30EQI208-3 unit pricing from authorized distributors ranges from approximately $38.50 at qty 1 down to about $19.80 at qty 1000, reflecting the LTB supply constraint and shrinking authorized-stock pool. Distributors such as DigiKey, Mouser, AIChipLink, and Nantian are showing stock counts in the low-hundreds rather than tens of thousands. Order-on-request quotes from independent brokers may differ significantly from these tier prices.
Where can I buy EPF10K30EQI208-3 online?
The EPF10K30EQI208-3 is currently stocked at DigiKey, Mouser, AIChipLink, Nantian, Micro-Semiconductor, and Vyrian. DigiKey (DigiKey part 6571285) and Mouser list the part under Intel's FPGA category. Independent brokers and salvage distributors also carry refurbished or factory-sealed stock; XAIPART offers matched inventory with cross-reference verification. Lead time on authorized-stock orders is typically 4-8 weeks as the LTB phase progresses.
What is the lead time for EPF10K30EQI208-3?
Authorized distributor lead time for EPF10K30EQI208-3 is currently 4-8 weeks as of September 2026, although last-time-buy stock can be exhausted without notice. According to the Intel PSG product change notification, last-time-buy orders must be placed before the published LTB cutoff date, with final deliveries scheduled 6-12 months after the LTB cutoff. Independent brokers can ship immediately but at higher unit cost and provenance risk.
Where do I download the EPF10K30EQI208-3 datasheet PDF?
The official Altera FLEX 10KE family datasheet (covering EPF10K30EQI208-3 and all package/speed variants) is hosted by Intel PSG at the Altera legacy documentation archive. The primary document is the FLEX 10KE Device Datasheet, which includes pinouts for the 208-PQFP, electrical characteristics, and timing models. Mirror copies are also available on components-store.com and through Intel's 'Altera Legacy' product support portal.
What is the pinout of EPF10K30EQI208-3 in 208-PQFP?
The 208-pin PQFP pinout for EPF10K30EQI208-3 is documented in the FLEX 10KE datasheet, with 147 dedicated user I/O pins, dedicated JTAG pins (TDI, TDO, TMS, TCK), configuration pins (nCONFIG, nSTATUS, CONF_DONE, MSELn, DCLK), four dedicated clock inputs (CLK0-CLK3), and power/ground pins (VCCINT, VCCIO, GND). The full pin assignment table is in section 8 of the FLEX 10KE datasheet. Engineers should reference the device-specific pinout file rather than the family pinout, because package-specific pinouts can shift I/O bank assignments.
Is EPF10K30EQI208-3 the same as EPF10K30AQI208-3?
No. The EPF10K30EQI208-3 belongs to the FLEX 10KE family (Embedded Array, ~30K gates, 1,728 LEs) while the EPF10K30AQI208-3 belongs to the FLEX 10KA family (older first-generation FLEX 10K architecture, ~30K gates, 1,728 LEs but with different EAB structure). Both share the 208-pin PQFP package, but the silicon die differs, so configuration bitstreams are NOT portable between the two.

Dữ liệu tham khảo kỹ thuật cho EPF10K30EQI208-3 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose EPF10K30EQI208-3 when you need an industrial-temperature (-40C to +85C) FLEX 10KE FPGA with the fastest -3 speed grade (12.5 ns) in a hand-rework-friendly 208-PQFP package. Choose EPF10K30EQI208-2 if your timing budget can accept ~15 ns propagation delay for cost savings. Choose EPF10K30EQC208-3 only for indoor commercial-temperature (0C to +70C) products where industrial grading is not required. Avoid mixing FLEX 10KE (E suffix) and FLEX 10KA (A suffix) bitstreams - they are not portable. For new designs not constrained by legacy 208-PQFP footprint, consider modern Cyclone IV EP4CE30 in BGA, but expect a full PCB redesign.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này EPF10K30EQI208-2 EPF10K30EQI208-2N EPF10K30AQI208-3N EPF10K30AQI208-3 EPF10K30EQC208-3 EPF10K30EQC208-3N
Package 208-BFQFP (RQ208) 208-BFQFP (RQ208) - same 208-BFQFP (RQ208) - same 208-BFQFP (RQ208) - same 208-BFQFP (RQ208) - same 208-BFQFP (RQ208) - same 208-BFQFP (RQ208) - same
Brand Intel Intel Intel Intel Intel Intel Intel
Series FLEX 10KE FLEX 10KE FLEX 10KE FLEX 10KA FLEX 10KA FLEX 10KE FLEX 10KE
Logic Elements 1,728 1,728 1,728 1,728 1,728 1,728 1,728
Speed Grade -3 (12.5 ns) -2 (~15 ns) -2 (~15 ns) -3 (12.5 ns) -3 (12.5 ns) -3 (12.5 ns) -3 (12.5 ns)
Operating Temperature -40C to +85C (Industrial) -40C to +85C (Industrial) -40C to +85C (Industrial) -40C to +85C (Industrial) -40C to +85C (Industrial) 0C to +70C (Commercial) 0C to +70C (Commercial)
User I/O 147 147 147 147 147 147 147
Lead-Free Finish Pb-free variants with -N suffix Standard (non-N) Pb-free (N suffix) Pb-free (N suffix) Standard (non-N) Standard (non-N) Pb-free (N suffix)

Bảo phân biệt quan trọng

  • FLEX 10KE embedded array architecture with MultiVolt I/O (vsEPF10K30AQI208-3 (FLEX 10KA))
  • Industrial temperature range with -3 fastest speed grade (vsEPF10K30EQC208-3 (Commercial temp))
  • 147 user I/O in a PQFP footprint enables legacy through-hole-compatible rework (vsCyclone IV EP4CE30 (BGA only))

Ghi chú thiết kế

The FLEX 10KE EPF10K30EQI208-3 requires separate VCCINT (2.5 V core) and VCCIO (2.5 V / 3.3 V / 5.0 V) rails with proper decoupling. According to Altera's configuration handbook, place 0.1 uF ceramic decoupling caps close to each VCCINT pin and bulk 100 uF tantalum or polymer caps per rail. Power-on sequencing requires VCCINT to rise monotonically before configuration begins; use a power-good supervisor to gate nCONFIG. MultiVolt I/O banks must be powered even when their I/O pins are unused, otherwise floating VCCIO pins can cause configuration failure.

The 208-pin PQFP package has 0.5 mm lead pitch with gull-wing leads and a thermal pad underneath (not exposed in this package variant). Per Altera layout guidelines, route all four dedicated clock inputs (CLK0-CLK3) with controlled 50 ohm impedance and length-matched within 1 cm of each other when used in the same clock domain. Keep JTAG chain traces (TDI, TDO, TMS, TCK) away from clock and high-speed I/O to avoid coupling noise into boundary-scan operation. Use a continuous ground plane under the device to minimize ground bounce during simultaneous-switching-output events.

Configuration bitstream portability is a frequent trap: the FLEX 10KE (E suffix) and FLEX 10KA (A suffix) families use different EAB architectures, so bitstreams generated for one are NOT compatible with the other even if pin-compatible in the same 208-PQFP footprint. Verify the silicon die suffix matches your Quartus project target. Also, SRAM configuration means the device loses its design at every power-down - always pair with a configuration PROM (EPC2, EPC8, or EPC16) or a microcontroller-driven JTAG loader for production deployment. Finally, do not drive JTAG signals before VCCINT is stable or the JTAG TAP controller may latch into an unknown state.

Thông tin tuân thủ

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
Không chì
Yes
Không halogen
Unknown
Khoáng vật xung đột
Compliant

RoHS compliance achieved with -N suffix variants (e.g., EPF10K30EQI208-2N). Industrial temperature grade per Intel PSG datasheet. Not AEC-Q100 qualified - this is an FPGA used in industrial/telecom, not automotive-grade silicon. Halogen-free status not explicitly stated in retrieved web data.

Dữ liệu được xác minh vào: 2026-09-11 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

EPF10K30EQI208-3 EPF10K30EQI208-3 datasheet FLEX 10KE FPGA 30K gates Altera FLEX 10KE 208 PQFP EPF10K30EQI208-3 price 2026 Intel FLEX 10KE last time buy EPF10K30E vs EPF10K30A EPF10K30EQI208-3 drop-in replacement EPF10K30EQI208-3 pinout 208 PQFP FLEX 10KE configuration PROM EPC2 what is the propagation delay of EPF10K30EQI208-3 EPF10K30EQI208-3 industrial temperature FPGA

Các bộ phận và thuật ngữ liên quan

Intel Altera Intel Programmable Solutions Group EPF10K30EQI208-3 EPF10K30EQI208-2 EPF10K30EQI208-2N EPF10K30AQI208-3 EPF10K30AQI208-3N EPF10K30EQC208-3 EPF10K30EQC208-3N FLEX 10KE FLEX 10KA FPGA Field Programmable Gate Array Programmable Logic Device PLD Embedded Array Block EAB Logic Element LE 208-BFQFP Power-QFP RQ208 MultiVolt I/O VCCINT VCCIO JTAG IEEE 1149.1 EPC2 EPC8 EPC16 Cyclone IV EP4CE30 Quartus RoHS Pb-free AEC-Q100 telecom line card PCI bus bridge industrial motor control PLC ARINC 429 MIL-STD-1553 boundary scan SRAM configuration serial passive configuration 0.22 um CMOS industrial temperature grade
Báo giá nhanh RFQ
Đội ngũ bán hàng của chúng tôi sẽ trả lời trong vòng 24 giờ
Mã sản phẩmMfrPkgSố lượngGiá mục tiêu
×
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

Giỏ hàng 0 mục
Giỏ hàng của bạn trống
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ