Intel

EPF6024AQC240-4N - FLEX 6000 FPGA, 24K Gates | Intel (Altera)

Name: EPF6024AQC240-4N - FLEX 6000 FPGA, 24K Gates | Intel (Altera)
Brand: Intel
SKU: EPF6024AQC240-4N

MPN: EPF6024AQC240-4N ✗ Cuối đời

3.3 V Vdss PQFP-240 (240-pin PowerQuad Flat Package) Package up to 172 MHz Speed

Yêu cầu báo giá

MOQ: 1 |

Xem tài liệu kỹ thuật (PDF) Xem các bộ thay thế

Số lượng

EPF6024AQC240-4N Tóm tắt

The Intel (formerly Altera) EPF6024AQC240-4N is a member of the FLEX 6000 family of CMOS SRAM-based Field-Programmable Gate Arrays (FPGAs), providing up to 24,000 typical gates in a 240-pin PowerQuad Flat Package (PQFP-240). The "-4" speed grade denotes the fastest available in the family, and the "N" suffix indicates a lead-free / Pb-free finish. The FLEX 6000 family uses a fine-grained Look-Up Table (LUT) architecture with continuous routing and OptiFLEX expansion, targeting low-cost, high-volume programmable logic designs where fast design changes during prototyping are required.

An FPGA (Field-Programmable Gate Array) is a type of programmable logic device (PLD) that lets designers configure digital logic through a four-step flow (design entry, place-and-route, simulation, programming) without fabricating a custom ASIC. FPGAs occupy the tier between small SPLDs/CPLDs and full ASIC mask sets in the digital design hierarchy: programmable logic -> PLD -> CPLD -> FPGA -> ASIC. The FLEX 6000 series sits at the low-density end of the FPGA taxonomy, intended as a low-cost alternative to gate arrays in glue logic, bus interface, and state-machine applications.

Key features of the EPF6024AQC240-4N include 1,960 logic elements (LEs) and 199 user I/Os, supplied by a 3.3 V core supply with 5 V-tolerant I/O. The device is configured via the IEEE 1149.1 (JTAG) boundary-scan port or the Altera passive serial/parallel configuration scheme, and it stores configuration in a serial configuration EEPROM. The device also supports in-system reprogrammability, allowing design changes without removing the part from the board.

The FLEX 6000 architecture implements each LE as a 4-input LUT plus a programmable register, with FastTrack continuous routing interconnect and MegaLAB structures grouping 16 LEs together. The I/O structure supports per-pin enable, slew-rate control, and PCI-compliant drive. With the -4 speed grade, the EPF6024AQC240-4N delivers the highest toggle performance of the family, with internal frequency targets up to 172 MHz.

Typical applications include bus-interface bridges (e.g., ISA-to-PCI glue), peripheral controllers, custom state machines, and low-cost prototyping of what would later become a mask-programmed gate array. The 240-pin PQFP package is easy to hand-solder and rework, which suits prototype and low-volume production runs.

When designing with this device, ensure configuration storage is sized for the bitstream (configuration memory requirement depends on the design). A JTAG chain is recommended for boundary-scan testability and in-system reconfiguration. Note that the FLEX 6000 family is a legacy part and is no longer recommended for new designs; consider Cyclone or MAX series for new projects.

This page synthesizes distributor pricing, same-package drop-in alternatives from the FLEX 6000 family, and practical design notes not found in the manufacturer datasheet.

Bộ thay thế dễ dàng lắp đặt cho EPF6024AQC240-4N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EPF6024AQC240-4N (cùng hình factor và footprint) — khác nhau ở Package, Speed Grade, Configuration Method, Device Type, Process Technology.

EPF6024AQC240-1N

Intel

Package: 240-pin PQFP (BFQFP)

Device Type: FPGA (Field Programmable Gate Array)

Process Technology: 0.42 µm CMOS