ICS525R-11 User-Configurable Clock Generator | Renesas
MPN: ICS525R-11 ✗ Cuối đờiICS525R-11 Tóm tắt
A clock generator is a clock-and-timing integrated circuit that converts one reference source into one or more synchronized output frequencies. In the broader semiconductor hierarchy, the ICS525R-11 belongs to the clock generator and frequency synthesizer family, which supports microprocessors, programmable logic, network interfaces, communications equipment, and test systems. Its differential PECL outputs are suited to systems requiring a high-speed, low-noise clock rather than a conventional CMOS clock.
The principal features are hardware-selectable configuration, a 40 MHz reference frequency, differential PECL clock generation, CMOS bus interfacing, and a 28-pin SSOP package. Grounding or floating the select pins allows the output frequency to be configured without firmware, software, or a device programmer. This makes the device useful where deterministic clock setup is preferred over programmable PLL control and where field configuration without a microcontroller is advantageous.
Technically, the ICS525R-11 uses an inexpensive crystal or external clock as its frequency reference and derives a high-frequency differential output through the clock-generation architecture described for the ICS525 family. Differential signaling helps reduce susceptibility to common-mode noise on high-speed interconnects. Because the part is obsolete, existing installations can use it as a known-good supply source, but new designs should account for its limited product life-cycle availability.
Typical applications include telecommunications and networking equipment, serial-interface clocking, FPGA or ASIC clock distribution, instrumentation, industrial control, and legacy data-acquisition systems. It is particularly appropriate when a fixed or selectable output frequency is needed, multiple dependent circuits require a coherent clock, and hardware-based configuration simplifies system startup.
For PCB design, use the manufacturer pin-description table when assigning tracks, verify the selected-pin logic for the required output frequency, and provide clean reference-clock routing. Differential PECL traces should be routed as a matched pair with controlled impedance and short return paths to reduce edge degradation and jitter.
This product summary consolidates electrical characteristics, package information, configuration details, lifecycle status, validated replacement information, and practical clock-routing guidance. It supports faster design review while preserving the distinction between confirmed device data and parameters that require confirmation from the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho ICS525R-11 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ICS525R-11 (cùng hình factor và footprint) — khác nhau ở Device Type, Package Body Width.
ICS525R-11LF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ICS525R-11 Thông số kỹ thuật
| Device Type | User-configurable clock generator |
| Manufacturer | Integrated Circuit Systems, now Renesas Electronics |
| Reference Frequency | 40 MHz |
| Output Architecture | Differential PECL clock output |
| Bus Interface | CMOS |
| Supply Voltage Range | 3 V to 5.5 V |
| Related 5 V Operating Range | 4.5 V to 5.5 V |
| Package Type | 28-pin SSOP |
| Package Body Width | 3.90 mm |
| Lead Pitch | 0.025 inch |
| Kiểu lắp đặt | Surface mount |
| Configuration Method | Grounded or floating select pins |
| Programming Requirement | No microcontroller, software, or device programmer |
| Trạng thái RoHS | Compliant |
| Trạng thái vòng đời | Obsolete |
| Manufacturer Document Reference | 525-01-02 |
Hướng dẫn cấu hình chân ICS525R-11 3.90 mm
Cấu hình chân cho ICS525R-11 (3.90 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ICS525R-11.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ICS525R-11 phù hợp cho 6 Áp dụngs: Telecommunications Clock Distribution, FPGA and ASIC Clocking, Network Interface Clocking, Industrial Control Systems, Test and Measurement Equipment, Data Acquisition and Conversion.
Telecommunications Clock Distribution
The ICS525R-11 suits legacy telecommunications equipment that requires a selectable, low-skew clock derived from a 40 MHz crystal or external reference. Its differential PECL output provides a common-mode-rejecting clock interface for line cards, interface controllers, and data-conversion equipment. Hardware selection of the output frequency simplifies startup because no device programmer is required. In a new telecommunications platform, confirm the obsolete part’s lifecycle constraints and validate the receiver’s PECL termination, clock amplitude, and jitter tolerance before committing the design.
Được đề xuất
FPGA and ASIC Clocking
The ICS525R-11 can provide a stable, selectable clock source for legacy FPGA or ASIC designs using differential PECL inputs. The 40 MHz reference architecture and hardware-configurable output allow several dependent logic domains to receive a coherent clock without software configuration. In implementation, place the generator near the receiving device, route the differential pair over a continuous plane, and follow the manufacturer’s termination requirements. Because the -11 reference is obsolete, it is best suited to sustaining existing platforms rather than new FPGA launches.
Được đề xuất
Network Interface Clocking
The ICS525R-11 is applicable to legacy network-interface and line-card designs requiring a deterministic reference-derived clock. Differential PECL signaling reduces common-mode pickup when the trace pair is routed with controlled impedance, while select-pin configuration permits hardware-level frequency setup. This is useful in equipment where an external processor should not be required to program a PLL during startup. Before use in a network appliance, verify input frequency tolerance, output jitter, receiver thresholds, and supply sequencing against the complete manufacturer documentation.
Được đề xuất
Industrial Control Systems
The ICS525R-11 can clock legacy industrial control, motion, and acquisition circuitry that accepts differential PECL timing. Its hardware-selectable outputs simplify deterministic boot behavior, while a 40 MHz reference can support compatible frequency-conversion requirements. Differential routing should be kept short and symmetrical within the controller enclosure to limit coupling from switching nodes and motor-control circuitry. For new industrial equipment, assess whether an active clock generator with a current product-life-cycle commitment provides a better sourcing path than this obsolete family member.
Được đề xuất
Test and Measurement Equipment
The ICS525R-11 is suitable for maintaining laboratory and industrial test systems that require multiple logic functions to share a selectable clock. Differential PECL outputs can feed compatible counters, converters, or acquisition circuits when the receiver threshold and termination are correct. The select-pin method also permits board-level frequency choices without firmware, which can simplify maintenance of multi-rate test fixtures. For new instruments, compare the obsolete device with active clock generators offering documented jitter, temperature range, calibration, and long-term lifecycle support.
Được đề xuất
Data Acquisition and Conversion
The ICS525R-11 can provide a reference-derived clock for legacy data-acquisition, analog-conversion, and digital-processing systems using differential PECL. Synchronizing converter and logic sections to one selectable clock can reduce timing uncertainty across the acquisition chain. The implementation should account for the 3 V to 5.5 V supply capability and the stated 4.5 V to 5.5 V range for related 5 V variants. Confirm output amplitude, jitter, and edge timing at the intended receiver before applying the clock to precision converters.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ICS525R-11 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ICS525R-11LF |
|---|---|---|
| Package | SSOP-28 | SSOP-28 |
| Brand | Renesas Electronics | Renesas Electronics |
| Device Type | User-configurable clock generator | User-configurable clock generator |
| Reference Frequency | 40 MHz | 40 MHz |
| Output Architecture | Differential PECL clock output | Differential PECL clock output |
| Bus Interface | CMOS | CMOS |
| Supply Voltage Range | 3 V to 5.5 V | 4.5 V to 5.5 V stated operating range |
| Configuration Method | Grounded or floating select pins | Hardware-selectable configuration |
| Programming Requirement | No microcontroller, software, or device programmer | No microcontroller, software, or device programmer |
Bảo phân biệt quan trọng
- Validated drop-in replacement path (vsICS525R-11LF)
- Hardware-only frequency configuration (vsICS525R-11LF)
- Differential PECL clock interface (vsICS525R-11LF)
Ghi chú thiết kế
Route each differential PECL output as a tightly coupled pair over a continuous reference plane. Keep the pair short, maintain symmetrical spacing, avoid stubs, and minimize layer transitions. Apply the manufacturer’s recommended termination at the receiving device and verify the completed trace impedance against the PCB stack-up. Differential signal quality directly affects edge timing and jitter, so a nominally correct schematic does not guarantee a clean clock at the receiver.
Do not select output frequencies from memory. Use the manufacturer’s select-pin truth table to determine which pins must be grounded or floating for each supported frequency, then test the resulting waveform with a scope or frequency counter. The 3 V to 5.5 V supply capability and the related 4.5 V to 5.5 V operating range for 5 V variants must also be reconciled with the circuit’s voltage levels before layout release.
Place the reference-crystal or clock-input network, the clock generator, and the receiving logic in a compact signal path. Keep the crystal loop small and maintain symmetrical output routing to reduce parasitic inductance and skew. Confirm decoupling values, supply sequencing, and grounding in the manufacturer application guidance. For obsolete-device maintenance, preserve the original footprint and pin assignment exactly so the validated ICS525R-11LF replacement can be used without board changes.
Thông tin tuân thủ
RoHS compliance is stated for the SSOP-28 ICS525R-11 variant documentation. The obsolete family classification does not constitute automotive qualification.