ISL8490IP - 5Mbps RS-485/RS-422 Transceiver | Renesas
MPN: ISL8490IP ✗ Cuối đờiISL8490IP Tóm tắt
A transceiver is an interface IC that converts digital logic signals into balanced differential signals for reliable communication over noisy or long cable runs. In the hierarchy, the ISL8490IP is a line transceiver, a type of interface IC and communications semiconductor. RS-485 supports multiple drivers and receivers on a shared bus, whereas RS-422 commonly uses a dedicated driver and receiver for point-to-point or multidrop networks. This transceiver supports both protocols and therefore provides a useful interface between CMOS/TTL logic and balanced cabling.
The verified headline specifications are a 5 V supply, 5 Mbps maximum data rate, 70 mV receiver hysteresis, 1 driver, 1 receiver, full-duplex operation, and support for RS-422 and RS-485. These parameters place the part in the low-power, high-speed or slew-rate-limited transceiver category described by the manufacturer documentation. The 8-pin PDIP format also permits conventional through-hole PCB assembly rather than requiring a fine-pitch surface-mount land pattern.
Technically, the balanced driver and receiver provide noise immunity over longer interconnects than ordinary single-ended logic. Receiver hysteresis helps distinguish signaling states in the presence of noise, while the 5 Mbps capability supports communication rates beyond the slow speeds commonly used by legacy RS-485 systems. Because the exact input capacitance, output timing, supply-current limits, and slew-rate settings are not included in the supplied verified excerpts, design engineers should confirm them in the manufacturer datasheet before finalizing timing, termination, and decoupling.
Typical uses include industrial controllers, building automation equipment, data acquisition systems, instrumentation, industrial networking equipment, and embedded control links. For an RS-485 bus, the circuit requires suitable line termination and biasing. For RS-422, driver and receiver connections should follow the source and destination topology specified by the system architecture rather than being treated as a multi-drop RS-485 bus.
The principal design consideration is signal integrity at 5 Mbps. Layout should minimize the distance between the transceiver, protection devices, connector, and differential pair, while keeping the two conductors of each balanced pair closely coupled. Decoupling close to the supply pin, controlled ground return paths, and appropriate surge protection help maintain reliable operation in industrial environments.
This page consolidates the verified distributor and manufacturer-document information with lifecycle status, procurement guidance, application fit, package details, and honest replacement limitations. It distinguishes confirmed facts from specifications that still require verification from the full Renesas datasheet.
Bộ thay thế dễ dàng lắp đặt cho ISL8490IP — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ISL8490IP (cùng hình factor và footprint) — khác nhau ở Number of Drivers, Number of Receivers, Package, Product Type.
ISL8480IP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ISL8481IP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ISL8482IP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ISL8491IP
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ISL8492IP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ISL8490IP Thông số kỹ thuật
| Product Type | RS-485/RS-422 transceiver |
| Điện áp cung cấp | 5 V |
| Maximum Data Rate | 5 Mbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Duplex Mode | Full duplex |
| Supported Protocols | RS-422 and RS-485 |
| Receiver Hysteresis | 70 mV |
| Khoảng nhiệt độ hoạt động | -40°C to +85°C |
| Hộp | 8-PDIP |
| Kiểu lắp đặt | Through-hole |
| Packaging Type | Tube/Rail |
| Logic Level | CMOS-compatible |
| Differential Signal Type | Balanced |
Hướng dẫn cấu hình chân ISL8490IP 8-pdip
Cấu hình chân cho ISL8490IP (8-pdip gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ISL8490IP.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ISL8490IP phù hợp cho 6 Áp dụngs: Industrial RS-485 Control Networks, Industrial Automation and Factory Equipment, Building Automation and HVAC Equipment, Data Acquisition and Instrumentation, RS-422 Point-to-Point Communication, Legacy Communication Equipment Maintenance.
Industrial RS-485 Control Networks
The ISL8490IP fits legacy industrial control links that use a 5 V supply, balanced RS-485 signaling, and a maximum data rate of 5 Mbps. Its one-driver, one-receiver arrangement provides a full-duplex interface between controller logic and a field bus or remote I/O module. The 8-PDIP package also suits through-hole industrial boards that are difficult to re-layout. Because the device is obsolete, engineers should reserve it primarily for maintenance of proven equipment and verify availability before committing to new production.
Industrial Automation and Factory Equipment
Factory machinery commonly distributes control and diagnostic information over balanced differential buses, where the ISL8490IP's RS-485 support and 5 Mbps data rate are useful. The transceiver can connect a controller or data-acquisition unit to motor controls, sensors, remote I/O, or supervisory equipment while reducing susceptibility to common-mode noise. Its documented -40°C to +85°C operating range supports industrial temperature conditions. Board-level surge and ESD protection should nevertheless be selected separately for the installation environment.
Building Automation and HVAC Equipment
The ISL8490IP is applicable to building-control panels, HVAC controllers, and supervisory systems that distribute commands over RS-485 or RS-422 links. Balanced differential signaling is valuable when cables pass near motors, lighting equipment, and other electrical noise sources, while the 5 Mbps ceiling supports more demanding control traffic than low-speed legacy buses. The through-hole 8-PDIP format is useful when servicing an existing controller. For new equipment, lifecycle availability and verified electrical equivalence must be checked before the part is approved.
Data Acquisition and Instrumentation
The ISL8490IP can bridge laboratory or field instrumentation to a host computer through a balanced RS-485 network. Its single transmitter and receiver suit point-to-point or bus-based acquisition, and the 5 Mbps maximum rate provides ample margin for many sensor and monitoring data streams. Differential signaling helps preserve data integrity over longer cable runs. Engineers should confirm receiver thresholds, timing margins, input capacitance, and cable-length limits in the full manufacturer datasheet before selecting termination and topology.
RS-422 Point-to-Point Communication
The ISL8490IP supports RS-422 in addition to RS-485, making it appropriate for dedicated links between a transmitter and receiver when a multidrop bus is unnecessary. Full-duplex capability allows send and receive paths to operate independently where the system architecture provides separate conductors for each direction. The 5 V supply and 5 Mbps capability are compatible with many legacy logic systems, but exact driver impedance, output levels, and propagation timing must be checked against the verified datasheet before sign-off.
Legacy Communication Equipment Maintenance
The obsolete ISL8490IP is most practical for repairing or extending equipment whose PCB already uses the 8-PDIP footprint and whose original design depends on the documented electrical behavior. It can avoid a risky board redesign when a qualified replacement has not yet been validated. Maintenance teams should match the full MPN, inspect device markings, confirm supply and pin compatibility, and document the substitution process. Because pricing and lifecycle supply are uncertain, stocking a small number of traceable parts may be more practical than assuming long-term availability.
Dữ liệu tham khảo kỹ thuật cho ISL8490IP — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ISL8480IP | ISL8481IP | ISL8482IP | ISL8491IP | ISL8492IP |
|---|---|---|---|---|---|---|
| Package | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
Bảo phân biệt quan trọng
- Five-megabit interface capability (vsISL8480IP)
- Documented receiver hysteresis (vsISL8481IP)
- Full-duplex RS-485 and RS-422 support (vsISL8482IP)
- Through-hole PCB compatibility (vsISL8491IP)
Ghi chú thiết kế
Route the RS-485 and RS-422 signals as a closely coupled differential pair with continuous ground reference, and minimize the distance from the ISL8490IP to the connector and any series protection components. Avoid routing the pair through switching-power or high-current motor nodes. The transceiver supports 5 Mbps, so uncontrolled stubs, long breaks in the ground path, and asymmetric trace geometry can reduce signal margin even when the logic-side wiring is correct.
Do not treat RS-422 point-to-point wiring and RS-485 multidrop wiring as electrically interchangeable. RS-485 may require bias resistors to establish a stable idle state when multiple receivers are connected, while termination belongs at the physical ends of the bus. Confirm whether the DE and RE pins are exposed in the design and control them properly before asserting the driver. Always use the manufacturer pinout because the supplied excerpts do not provide verified numbered pin assignments.
Place the required supply-decoupling capacitor immediately adjacent to the transceiver’s power and ground pins, and keep the return current path short and continuous. The ISL8490IP is identified as a 5 V low-power device, but its complete supply tolerance and current limits are not present in the supplied excerpts. Verify those values in the manufacturer datasheet and ensure the upstream 5 V rail has adequate transient response for the transceiver and any protection circuitry.
The part is marked obsolete, so inventory condition and provenance can vary. Purchase by the exact ISL8490IP MPN, request lot traceability where available, and perform incoming inspection before installation. For maintenance work, compare the replacement’s pinout, logic levels, receiver thresholds, propagation delay, output impedance, and supply requirements rather than relying only on the RS-485 and RS-422 labels.
Thông tin tuân thủ
The supplied verified excerpts do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The product was published in 2003, but publication date does not establish regulatory compliance.
