LAN8700C-AEZG-TR - 10/100 Ethernet PHY | Microchip
MPN: LAN8700C-AEZG-TR ✓ Hoạt độngLAN8700C-AEZG-TR Tóm tắt
An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, is the component that converts digital data between a host controller and the physical copper network. It belongs to the network-interface hierarchy: Ethernet transceiver → Ethernet interface IC → integrated circuit. The LAN8700C handles the MII or RMII digital signaling and analog signaling required for 10BASE-T and 100BASE-TX networks, while HP Auto-MDIX simplifies cabling by allowing the PHY to negotiate transmit and receive pairs automatically.
Key features include support for both MII and RMII host interfaces, HP Auto-MDIX operation, and ±15 kV ESD protection. The 36-QFN package measures 6 x 6 mm, making the device suitable for compact embedded platforms. Variable I/O voltage helps the PHY interface with a wider range of host logic, while the single-supply option simplifies power planning when only 3.3 V is readily available.
The architecture supports a 50 MHz reference-clock arrangement with a permitted tolerance of ±50 ppm and a duty cycle from 40% to 60%. In an RMII design, the host controller supplies the reference clock and handles the parallel data interface. The integrated regulator can then produce the required 1.8 V internal rail from a 3.3 V input. Designers must still observe the recommended capacitor values, layout geometry, clocking, and decoupling arrangements in the manufacturer datasheet.
Typical applications include industrial Ethernet controllers, embedded routers, programmable logic controllers, factory automation equipment, motor-control systems, security appliances, and compact network-connected sensors. The MII interface offers broader compatibility with conventional Ethernet controllers, while RMII reduces the number of host-side signals and is often preferred for compact systems with an integrated Ethernet MAC.
The main design consideration is PCB implementation. A 36-QFN device has short leads and a compact thermal pad, so accurate footprint alignment, clean ground return paths, short high-frequency connections, and uninterrupted ground-plane continuity are important. Magnetic isolation, RJ45 integration, and ESD protection must be designed according to the applicable Ethernet physical-layer requirements and the manufacturer reference guidance.
This product page combines the manufacturer electrical description with package information, focused application guidance, practical layout considerations, and same-footprint alternatives. It is intended to help engineers determine whether the LAN8700C-AEZG-TR fits an existing embedded Ethernet design before requesting a quote or committing the component to a bill of materials.
Bộ thay thế dễ dàng lắp đặt cho LAN8700C-AEZG-TR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LAN8700C-AEZG-TR (cùng hình factor và footprint) — khác nhau ở Host Interface, Package.
LAN8700C-AEZG
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LAN8700IC-AEZG
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LAN8700C-AEZG-AR2
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LAN8700C-AEZG-TR Thông số kỹ thuật
| Ethernet Support | 10BASE-T and 100BASE-TX |
| Host Interface | MII and RMII |
| ESD Protection | ±15 kV |
| Auto-MDIX Support | HP Auto-MDIX |
| Reference Clock Frequency | 50 MHz ±50 ppm |
| Reference Clock Duty Cycle | 40% to 60% |
| Single-Supply Configuration | 3.3 V |
| Integrated Regulator Output | 1.8 V from 3.3 V input |
| Temperature Grade | Industrial temperature |
| Hộp | 36-QFN, 6 x 6 mm |
| Số chân | 36 pins |
| Kiểu lắp đặt | Surface mount |
| Trạng thái RoHS | Compliant |
| Lead-Free Status | Lead-free |
| Supply Configuration | Single 3.3 V supply or variable I/O voltage |
Hướng dẫn cấu hình chân LAN8700C-AEZG-TR 36-qfn, 6 x 6 mm
Cấu hình chân cho LAN8700C-AEZG-TR (36-qfn, 6 x 6 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho LAN8700C-AEZG-TR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LAN8700C-AEZG-TR phù hợp cho 6 Áp dụngs: Industrial Automation Controllers, Embedded Network Gateways, Programmable Logic Controllers, Network Security Appliances, Motor Control and Condition Monitoring, Connected Sensors and Test Equipment.
Industrial Automation Controllers
The LAN8700C-AEZG-TR fits industrial automation controllers that need a compact 10/100 Ethernet connection beside a microcontroller or application processor. Its MII and RMII interfaces let the same PHY support controllers with different parallel-network architectures, while HP Auto-MDIX removes manual transmit-pair and receive-pair configuration. The 36-QFN 6 x 6 mm package preserves board area in compact PLC and factory-control products. A design using a single 3.3 V rail can also use the integrated 3.3 V-to-1.8 V regulator, subject to the manufacturer power and decoupling guidance. Industrial qualification should cover the complete enclosure temperature range, Ethernet magnetics, surge environment, and production-test process.
Được đề xuất
Embedded Network Gateways
LAN8700C-AEZG-TR is appropriate for embedded gateways that connect local control electronics to an Ethernet backbone. RMII is useful when minimizing host-side pins is important, while MII remains available for controllers requiring the conventional parallel interface. HP Auto-MDIX supports installation with either conventional pair arrangement, which is valuable in field-wired industrial systems. The device’s 50 MHz reference-clock requirement should be included in the host clock-budget analysis, with oscillator accuracy, tolerance, and temperature drift combined so the final clock remains within ±50 ppm. The PCB should provide a continuous ground reference and short connections around the compact 36-QFN footprint.
Được đề xuất
Programmable Logic Controllers
The LAN8700C-AEZG-TR can add 10/100 Ethernet connectivity to programmable logic controllers without requiring a large modular communications package. MII provides a direct path for controllers with a conventional Ethernet MAC interface, and RMII provides a lower-pin-count alternative for more integrated designs. The compact 36-QFN 6 x 6 mm package is useful when the PLC main board has limited connector and component space. For reliable operation, the design should account for the 50 MHz ±50 ppm reference-clock requirement, provide the required bypass and filtering capacitors, and keep magnetic-component and trace-routing decisions separate from the digital host interface.
Được đề xuất
Network Security Appliances
The LAN8700C-AEZG-TR can serve as the 10/100 Ethernet network interface in compact security controllers, access points, and monitoring equipment. Its ±15 kV ESD protection supports protection-aware designs, while Auto-MDIX improves installation flexibility for devices connected through varied field cabling. RMII is especially relevant to security appliances based on application processors that minimize peripheral pin count. The PHY remains a 100 Mb/s component, so it should be selected where throughput requirements are modest or where a higher-bandwidth interface would not justify its complexity. Layout must maintain a low-impedance ground path and follow the manufacturer’s analog and digital partitioning recommendations near the QFN pads.
Được đề xuất
Motor Control and Condition Monitoring
LAN8700C-AEZG-TR is suitable for motor-drive controllers and condition-monitoring equipment that must report operating data over Ethernet. A 10/100 link can carry supervisory information such as temperature, vibration, fault status, and configuration updates without determining the primary motor-control timing path. The industrial-temperature characterization supports its use in embedded industrial equipment, while HP Auto-MDIX reduces cabling errors in field installations. Designers should separate noisy switching and motor-power areas from the Ethernet PHY, observe the recommended magnetic-component placement, and validate conducted and radiated emissions in the final enclosure rather than treating PHY ESD protection as a complete system-level surge solution.
Được đề xuất
Connected Sensors and Test Equipment
The LAN8700C-AEZG-TR enables connected sensors, data loggers, and test equipment to join a 10/100 Ethernet network while keeping the physical interface compact. MII or RMII compatibility makes it suitable for host processors with an embedded Ethernet MAC, and the single-3.3 V option can simplify power architecture in portable or distributed systems. The reference clock must meet the manufacturer’s 50 MHz ±50 ppm frequency tolerance and 40% to 60% duty-cycle limits. Layout planning should minimize digital return paths beneath the PHY, maintain the exposed-pad ground connection, and use controlled copper geometry to support repeatable high-speed Ethernet performance.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LAN8700C-AEZG-TR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LAN8700C-AEZG | LAN8700IC-AEZG | LAN8700C-AEZG-AR2 |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 36-QFN (6x6) | 36-QFN (6x6) | 36-QFN (6x6) | 36-QFN (6x6) |
| Ethernet Speed | 10/100 Ethernet | 10/100 Ethernet | 10/100 Ethernet | 10/100 Ethernet |
| Host Interface | MII and RMII | MII and RMII | MII and RMII | MII and RMII |
| Auto-MDIX | HP Auto-MDIX | HP Auto-MDIX | HP Auto-MDIX | HP Auto-MDIX |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV | ±15 kV |
| Single-Supply Configuration | 3.3 V with integrated 1.8 V regulator | 3.3 V with integrated 1.8 V regulator | 3.3 V with integrated 1.8 V regulator | 3.3 V with integrated 1.8 V regulator |
| Reference Clock | 50 MHz ±50 ppm, 40% to 60% duty cycle | 50 MHz ±50 ppm, 40% to 60% duty cycle | 50 MHz ±50 ppm, 40% to 60% duty cycle | 50 MHz ±50 ppm, 40% to 60% duty cycle |
Bảo phân biệt quan trọng
- Supports both common embedded-host Ethernet interfaces (vsLAN8700C-AEZG)
- Single-3.3 V operation simplifies compact power architectures (vsLAN8700IC-AEZG)
- Industrial-temperature operation with network-installation flexibility (vsLAN8700C-AEZG-AR2)
Ghi chú thiết kế
Implement the LAN8700C-AEZG-TR on a multilayer board with an uninterrupted ground plane and a low-impedance connection from the QFN exposed pad to ground. Keep the 50 MHz reference-clock route short and controlled, separate it from Ethernet magnetics and switching-power stages, and follow the manufacturer footprint dimensions directly. Because the package is only 6 x 6 mm, land-pattern errors can become assembly defects or impedance discontinuities, so verify pad geometry against the current package drawing before release.
Apply the manufacturer’s recommended input, output, and bypass capacitors directly at the relevant power pins. For a single-3.3 V configuration, confirm that the integrated 3.3 V-to-1.8 V regulator has adequate input decoupling and does not create unacceptable supply ripple in the host system. Validate the power-up sequence, 50 MHz clock availability, and operating current across the required temperature range. Use estimated calculations for board-level dissipation and check them against the device thermal limits before production release.
Do not assume that any LAN8700C suffix is automatically interchangeable. Compare the exact ordering code, package drawing, temperature grade, reference-clock arrangement, qualification status, and tape-and-reel format. The related LAN8700C-AEZG, LAN8700IC-AEZG, and LAN8700C-AEZG-AR2 share the 36-QFN form factor, but an engineering change must still be approved against the manufacturer datasheet and the company’s component-qualification process.
Plan the Ethernet analog path around the manufacturer’s recommended magnetics and filtering arrangement, and keep high-current digital and switching circuitry away from the PHY’s analog pins. ESD protection provides a defined device-level withstand rating, but it does not replace system-level surge, common-mode, or emission validation. Test the assembled product with its final enclosure, connector, cable, power supply, and ground configuration because those elements can materially change coupling into the Ethernet interface.
Thông tin tuân thủ
The manufacturer LAN8700/LAN8700i documentation identifies a lead-free, RoHS-compliant 36-pin QFN package. The target is described as an industrial-temperature product, so automotive qualification under AEC-Q100 is not indicated.