LM224KNE4 - Quad 30V 1.2MHz Op Amp | Texas Instruments
MPN: LM224KNE4 ✓ Hoạt độngLM224KNE4 Tóm tắt
An operational amplifier is a high-gain analog building block used to amplify small voltage signals, buffer sensors, implement active filters, and drive higher-impedance loads. The LM224 belongs to the broader hierarchy of operational amplifiers, analog amplifiers, and integrated analog signal-processing ICs. Its four amplifiers share a power supply while operating independently, allowing one package to implement several stages of a signal chain while conserving PCB area.
The LM224KNE4 provides a 1.2 MHz gain-bandwidth product, a 30 V maximum supply capability, and approximately 3 mV typical input-offset voltage. Typical input-offset current is 2 nA, while input-bias current is approximately 20 nA. The device also offers improved 2 kV ESD protection. These characteristics support accurate closed-loop amplification when appropriate external feedback and compensation components are selected according to the manufacturer's application guidance.
The four amplifiers are internally frequency compensated, simplifying basic gain configurations without requiring external compensation in ordinary closed-loop operation. The LM224 series supports operation from a single supply, and its common-mode input range includes ground, which is useful for signals referenced to the lower supply rail. Low input-bias and input-offset currents also reduce errors when the source impedance is relatively high.
Typical uses include sensor-signal conditioning, process-control instrumentation, active analog filtering, low-frequency audio and communications circuitry, and general industrial control systems. Because the package contains four amplifiers, applications such as instrumentation amplifiers, multi-stage filters, bridge amplifiers, and four-channel signal-conditioning boards can reduce both component count and board space. Input and output signal ranges must remain within the electrical limits for the selected supply voltage.
For reliable PCB implementation, follow the manufacturer pinout and place input, output, and supply connections to minimize noise pickup and unwanted oscillation. Keep sensitive input traces short, provide adequate decoupling across the supply pins, and avoid placing high-impedance signal routes beside fast-switching nodes. Stable feedback-network layout is particularly important when the amplifier operates near its 1.2 MHz gain-bandwidth product.
This product summary combines the manufacturer device information, ordering details, distributor listings, and documented cross-reference results into an engineering-oriented view of the LM224KNE4. It also identifies same-footprint alternatives, highlights parameter differences, and adds practical guidance for power bypassing, input routing, feedback layout, and replacement qualification.
Bộ thay thế dễ dàng lắp đặt cho LM224KNE4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM224KNE4 (cùng hình factor và footprint) — khác nhau ở Package, Maximum Supply Voltage, Operating Temperature Range, Amplifier Count, Input Offset Voltage.
LM224NE4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM224N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM224KAN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM224AN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM224KNE4 Tỷ lệ tối đa & tính chất điện
| Amplifier Count | 4 amplifiers |
| Product Type | Quad operational amplifier |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Khoảng nhiệt độ hoạt động | -25°C to +85°C |
| ESD Protection | 2 kV |
| Typical Input Offset Voltage | 3 mV |
| Typical Input Offset Current | 2 nA |
| Typical Input Bias Current | 20 nA |
| Typical Supply Current | 0.8 mA |
| Internal Frequency Compensation | Internally frequency compensated |
| Common-Mode Input Range | Includes ground |
| Supply Configuration | Single supply |
| Hộp | 14-pin PDIP |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân LM224KNE4 14-pin pdip
Cấu hình chân cho LM224KNE4 (14-pin pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM224KNE4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM224KNE4 phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Active Analog Filters, Process Control Interfaces, Power-Supply Monitoring, Audio Preamplifier Stages, Portable Measurement Equipment.
Industrial Sensor Signal Conditioning
The LM224KNE4 is well suited to conditioning low-level sensor signals because it combines approximately 20 nA typical input-bias current with a 1.2 MHz gain-bandwidth product per amplifier. Its common-mode input range includes ground, which permits operation with sensors referenced close to the lower supply rail. Four amplifiers in one 14-pin PDIP can implement stages such as instrumentation amplification, level shifting, buffering, and active filtering. The circuit designer should still verify the sensor output range, source impedance, and required precision against the complete electrical characteristics. Feedback resistors should be placed close to the amplifier inputs, and sensitive input traces should be kept away from switching nodes to minimize coupled noise.
Được đề xuất
Active Analog Filters
The four internally compensated amplifiers in the LM224KNE4 provide a practical way to implement multiple active-filter sections without occupying four separate packages. Its 1.2 MHz gain-bandwidth product provides useful bandwidth for precision, control, and low-frequency communications applications, while the approximately 3 mV typical input-offset voltage can influence DC accuracy in high-gain stages. Select resistor and capacitor values according to the manufacturer’s guidance and verify stability with the intended gain and load. Close physical placement of feedback components is especially important because parasitic resistance and capacitance can alter cutoff frequency and phase margin. The same package can also combine filtering with a final output buffer for driving a downstream measurement circuit.
Được đề xuất
Process Control Interfaces
The LM224KNE4 can serve as the analog interface between low-power sensors and a control MCU in industrial process-control equipment. Its single-supply operation, ground-inclusive common-mode input range, and approximately 0.8 mA typical supply current suit low-power analog sections, while four independent amplifiers allow signal amplification, filtering, offsetting, and output buffering to share one package. The -25°C to +85°C operating range covers many commercial and industrial environments. For reliable operation, the selected supply must keep every amplifier input and output within its permitted ranges, and the board layout should isolate sensitive analog routing from digital and power-conversion signals.
Được đề xuất
Power-Supply Monitoring
The LM224KNE4 can amplify the difference between a monitored supply and a reference signal, then buffer that result for an ADC or comparator. Its 1.2 MHz gain-bandwidth product is more than adequate for many monitoring loops, and the common-mode input range including ground is useful for measurements near the bottom rail. However, the input offset voltage and input bias current determine the achievable measurement resolution, so source impedance and resistor matching must be considered. The four-amplifier package can implement an instrumentation stage, anti-alias filter, gain stage, and output buffer in one footprint. Decouple the supply pins locally and maintain short feedback paths to reduce measurement error.
Được đề xuất
Audio Preamplifier Stages
The LM224KNE4 can implement low-frequency audio preamplifier and mixing stages where a 1.2 MHz gain-bandwidth product and four amplifiers provide a useful combination of gain and integration. The ground-inclusive common-mode input range supports single-supply operation, allowing input and output signals to be biased near the lower rail. Designers must account for approximately 3 mV typical input-offset voltage, which can influence headroom and distortion in small-signal stages, and should select suitable coupling capacitors and bias networks. The internally compensated amplifiers simplify closed-loop gain stages, but stable feedback layout and clean grounding remain essential for low-noise performance.
Được đề xuất
Portable Measurement Equipment
For portable instruments, the LM224KNE4 offers four amplifiers, approximately 0.8 mA typical supply current, and operation from a single supply in one 14-pin PDIP package. These characteristics are useful in handheld probes, portable test equipment, and compact sensor interfaces where component count and current consumption influence battery life. The -25°C to +85°C rating and 2 kV ESD protection support robust general-purpose designs, while the common-mode input range including ground simplifies measurements near the supply’s lower rail. Designers should minimize input-node capacitance, stabilize feedback loops, and provide local supply bypassing to reduce noise and maintain predictable operation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM224KNE4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM224NE4 | LM224N | LM224KAN | LM224AN |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin PDIP | 14-pin PDIP - same footprint | 14-pin PDIP - same footprint | 14-pin PDIP - same footprint | 14-pin PDIP - same footprint |
| Amplifier Count | 4 | 4 | 4 | 4 | 4 |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Internal Frequency Compensation | Yes | Yes | Yes | Yes | Yes |
Bảo phân biệt quan trọng
- Four amplifiers share one 14-pin PDIP package (vsLM224N)
- Documented 2 kV ESD-protection rating (vsLM224AN)
- Exact KNE4 ordering option for BOM continuity (vsLM224NE4)
- Single-supply operation with ground-inclusive common-mode input (vsLM224KAN)
Ghi chú thiết kế
Place the LM224KNE4 close to the protected signal source and place input-biasing, feedback, and compensation networks directly beside the associated amplifier pins. A 14-pin PDIP provides convenient through-hole access, but long exposed input loops can act as antennas. Route the four amplifier channels separately when their source impedances differ, and avoid sharing a high-impedance node between channels.
Use a single supply that keeps all amplifier inputs and outputs within the manufacturer’s permitted ranges. Decouple the supply pins locally with a suitable bypass network, following the manufacturer’s guidance for ceramic and bulk capacitance. Because the LM224KNE4 typically draws about 0.8 mA, supply-demand calculations must also include output-current and load-path losses; package heating depends on the actual operating current and voltage drop.
Keep feedback resistors short and symmetrical, especially in high-gain or precision stages. The 1.2 MHz gain-bandwidth product limits practical closed-loop bandwidth, but parasitic capacitance in the feedback network can still reduce phase margin and produce ringing. Use a ground reference that returns directly beneath the circuit, avoid routing sensitive inputs beside the clocked digital section, and verify stability with the actual load and source impedance.
Do not assume that every LM224 suffix is automatically interchangeable in production. LM224KNE4, LM224NE4, LM224N, LM224KAN, and LM224AN are closely related, but package code, temperature grade, ordering conditions, and marking can differ. Confirm the manufacturer ordering table, package drawing, pin assignments, operating-temperature range, and qualification requirements before revising a production bill of materials.
Thông tin tuân thủ
The device is a general-purpose -25°C to +85°C industrial-temperature amplifier rather than an automotive-qualified product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer’s current product documentation or declaration.