LM2901SNG - Quad Comparator, ±18V/36V, 14-PDIP | onsemi
MPN: LM2901SNG ✓ Hoạt độngLM2901SNG Tóm tắt
An analog comparator is a semiconductor that compares two input voltages and produces a logic-level output indicating which input is higher. The LM2901 family combines four independent comparator channels on one monolithic integrated circuit. Its common-mode input range includes ground, allowing the device to operate from single-supply or dual-supply arrangements while comparing signals near 0 V.
The LM2901SNG supports general-purpose comparison with an open-collector output structure, as identified in manufacturer-family information for the LM2901 series. Open-collector outputs require an external pull-up resistor and allow several outputs to be wired together when the system needs a wired-AND function. Each channel has independent inputs, making the quad configuration useful when four threshold decisions are required in one package.
A typical implementation places a reference voltage on one input and a sensor or divided signal on the other. The comparator output changes state when the signal crosses the reference. Because comparator accuracy and behavior depend on input common-mode voltage, supply voltage, output pull-up value, and source impedance, designers should consult the onsemi LM2901 datasheet for recommended operating conditions and electrical characteristics.
Typical uses include industrial sensor thresholding, battery voltage monitoring, overvoltage and undervoltage detection, window-comparison circuits, and general control logic. The 14-pin PDIP format is particularly suitable for through-hole industrial assemblies, prototypes, repair work, and educational platforms where socketed components or easy inspection are preferred.
When laying out a circuit, place input resistors close to the relevant comparator pins and route the open-collector output away from high-impedance analog inputs to reduce switching transients. Select the pull-up resistor for the required sink current and logic family, and account for the output's open-collector state during fault analysis.
This product record combines the onsemi family description, package information, source references, drop-in candidates, and practical design guidance. It also distinguishes true 14-pin PDIP replacements from similarly named devices offered in SOIC or other packages, helping engineers evaluate PCB compatibility before making a design change.
Bộ thay thế dễ dàng lắp đặt cho LM2901SNG — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2901SNG (cùng hình factor và footprint) — khác nhau ở Comparator Type, Logic Compatibility, Supply Configuration, Supply Voltage Range, Mounting Type.
LM2901NG
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2901N/PB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM339AN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2901SNG Tỷ lệ tối đa & tính chất điện
| Comparator Type | General-purpose quad comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | ±18 V |
| Maximum Total Supply Voltage | 36 V |
| Common-Mode Input Voltage Range | Includes ground V |
| Kiểu đầu ra | Open-collector |
| Hộp | 14-pin PDIP |
| Kiểu lắp đặt | Through-hole |
| Supply Configuration | Single or dual supply |
Hướng dẫn cấu hình chân LM2901SNG 14-pin pdip
Cấu hình chân cho LM2901SNG (14-pin pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM2901SNG.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM2901SNG phù hợp cho 6 Áp dụngs: Industrial Sensor Thresholding, Battery Voltage Monitoring, Power-Supply Window Comparison, Motor and Actuator Control, Consumer Level Detection, Automotive and Heavy Equipment Logic.
Industrial Sensor Thresholding
The LM2901SNG is well suited to industrial threshold detection because it combines four independent comparator channels with a common-mode input range that includes ground. A sensor output can be divided to a suitable reference level and applied to one input, while the reference voltage drives the other. The open-collector result can drive a pull-up-based digital input or a transistor stage. Its ±18 V, or 36 V total, supply description also supports systems with wider rails than conventional 5 V logic, although every input and output must remain within its operating limits.
Được đề xuất
Battery Voltage Monitoring
The LM2901SNG can implement overvoltage, undervoltage, or battery-state detection by comparing a divided pack voltage against a reference. The ground-inclusive common-mode range is valuable when the monitored signal approaches 0 V, while four channels allow multiple pack thresholds to be evaluated in parallel. Each open-collector output requires a pull-up, and the circuit should include hysteresis or filtering when battery impedance and temperature variation could move the comparison point repeatedly. The 36 V total supply capability accommodates higher-energy packs, subject to the manufacturer's detailed operating limits.
Được đề xuất
Power-Supply Window Comparison
A pair of LM2901SNG channels can establish upper and lower thresholds for a power rail, creating a voltage window rather than a single set point. The comparator inputs receive a divided rail voltage and two references, and their open-collector outputs can be combined through pull-ups to indicate whether operation is inside or outside the acceptable range. This arrangement supports sequencing, fault flags, and system-enable logic. Because comparator offset and input bias affect the threshold, the design should use appropriate resistor values and verify margin at the expected supply tolerance and temperature.
Được đề xuất
Motor and Actuator Control
The LM2901SNG can compare a control signal against a reference and produce an open-collector command for a motor-driver or actuator interface. The four independent channels make it possible to monitor more than one motion or safety condition without adding separate comparator packages. An external pull-up establishes the digital output level, and a driver transistor can provide the current required by a motor, relay, or solenoid. Layout must keep switching-node wiring away from comparator inputs, and the chosen driver should provide isolation from inductive transients and back-emf.
Được đề xuất
Consumer Level Detection
The LM2901SNG can compare a scaled control signal with a reference to detect button, selector, or accessory levels in a consumer system. Its common-mode range including ground simplifies comparisons around a zero-volt baseline, and the four-channel architecture consolidates several independent decisions into one 14-pin device. Open-collector outputs are useful when driving a common pull-up bus or wired-AND status line. Designers should add appropriate input filtering, account for the external pull-up's loading, and confirm that the selected ordering code meets the product's environmental and lifecycle requirements.
Được đề xuất
Automotive and Heavy Equipment Logic
The LM2901SNG can support threshold logic in automotive, agricultural, and heavy-equipment control modules when its operating limits and qualification requirements match the design. The wide stated supply capability of ±18 V, or 36 V total, is useful for systems with protected vehicle rails, but the designer must still analyze transient suppression and ensure every comparator pin remains within its absolute limits. The PDIP package supports through-hole production and field-replaceable assemblies. Automotive programs should verify the exact onsemi ordering code, temperature grade, qualification status, and production-life requirements before release.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2901SNG — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2901NG | LM2901N/PB | LM339AN |
|---|---|---|---|---|
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Package | 14-PDIP | 14-PDIP | 14-DIP | 14-DIP |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Product Family | LM2901 | LM2901 | LM2901 | LM339 |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole |
Bảo phân biệt quan trọng
- Exact onsemi LM2901-family 14-PDIP replacement candidate (vsLM2901NG)
- Preferred same-family source for cross-manufacturer review (vsLM2901N/PB)
- Ground-inclusive input characteristic for zero-volt thresholding (vsLM339AN)
Ghi chú thiết kế
Do not treat every LM2901-family ordering code as a PCB-compatible substitute. LM2901SNG is specified in a 14-PDIP package, while similarly named LM2901 devices may use SOIC packages with a different footprint. Before replacement, compare every numbered pin, the open-collector output arrangement, common-mode input range, supply limits, input offset, response time, and operating temperature grade. A matching package count alone does not guarantee identical pin functions.
Place input compensation or bias resistors close to the associated comparator pins to limit parasitic pickup and input-current errors. Keep the pull-up resistor near the output pin, route open-collector nets away from sensitive analog inputs, and provide a stable return path for the power supply. In through-hole layouts, maintain adequate spacing between adjacent pins and provide solder-joint access that does not obstruct the package or nearby components.
An open-collector output transitions rapidly from the pull-up voltage toward the low output level, so the external resistor and input capacitance determine the rising-edge speed. Choose a pull-up that satisfies the logic family's sink-current requirement without being so weak that leakage produces excessive rise time. If several comparator outputs share a bus, include the aggregate sink current in the calculation and verify that fault conditions do not pull the shared node below its valid logic level.
Thông tin tuân thủ
The LM2901SNG product and family information does not establish a complete compliance profile. Automotive suitability depends on the exact ordering code and qualification documentation.