onsemi

LM2903DMR2G - Dual Low Offset Voltage Comparator | onsemi

MPN: LM2903DMR2G ✓ Hoạt động
2 V to 36 V (single supply) Vdss 700 uA (typ) Id 8-MSOP (Micro8), Case Outline 846A-02 Package
MOQ: 1 |

LM2903DMR2G Tóm tắt

The onsemi LM2903DMR2G is a dual independent precision voltage comparator with 2 mV typical input offset voltage, 1.3 us typical response time, and a wide 2 V to 36 V supply range, housed in an 8-pin MSOP (Micro8) surface-mount package.

A voltage comparator is an analog building block that compares two input voltages and drives its output to indicate which input is higher. Comparators form the lowest tier of the amplifier IC hierarchy (comparator -> amplifier IC -> analog signal chain IC -> semiconductor) and differ from op-amps by their open-collector outputs and fast, unsaturated switching behavior. The LM2903 belongs to the industry-standard LM393 comparator family, which has been the default choice for level detection, threshold monitoring, and limit sensing across consumer, automotive, and industrial electronics for decades.

Key features include low input offset voltage as low as 2.0 mV, input common-mode range extending down to ground (V-) level even under single-supply operation, low supply current of approximately 700 uA per package, and open-collector outputs compatible with TTL, MOS, and CMOS logic levels. The wide 2 V to 36 V single-supply range (or equivalent split-supply operation) allows direct connection to automotive 12 V and industrial 24 V rails without preconditioning.

Architecturally, the device integrates two fully independent comparator channels that share only the supply pins, permitting simultaneous use without channel-to-channel interaction. The open-collector output stage requires an external pull-up resistor, which lets designers set the logic interface level independently of the supply - a 5 V pull-up on a 12 V-powered comparator interfaces directly with TTL logic.

Typical applications include limit comparators and threshold detectors in power supplies, window comparators in battery chargers and over-voltage protection circuits, sensor conditioning for industrial automation, and level translation and oscillator timing circuits in consumer electronics.

A key design consideration: because the output is open-collector, forgetting the pull-up resistor produces a permanently floating output; select the pull-up value for the required rise time and sink current, typically 3 k to 15 k. Also keep input differential voltage within the absolute maximum rating.

This page consolidates verified electrical specifications, drop-in alternatives, application guidance, and practical design notes not found in a single manufacturer document.

Bộ thay thế dễ dàng lắp đặt cho LM2903DMR2G — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2903DMR2G (cùng hình factor và footprint) — khác nhau ở Output Type, Package, Comparator Type, Number of Channels, Input Common-Mode Range.

Texas Instruments
Output Type: Open-collector
Package: 8-VSSOP (8-MSOP, 0.118 inch width)
Comparator Type: Dual differential comparator
So sánh với LM2903DMR2G →
Texas Instruments
Output Type: Open-collector, rail-to-rail
Package: TSSOP (PW), 8 pins
Comparator Type: Dual differential comparator
So sánh với LM2903DMR2G →
onsemi
Output Type: Open collector
Package: 8-MSOP
Comparator Type: Dual, independent precision voltage comparator
So sánh với LM2903DMR2G →

LM393DMR2G

✅ Drop-In
onsemi
📦 8-MSOP (Micro8)
Dual, independent precision voltage comparator · 2 channels · 2 V to 36 V · As low as 2.0 mV · Rail-to-rail · Open collector · Single or split supply · 8-MSOP

Liên hệ để biết giá

Xem tài liệu →

LM2903DGKRG4

✅ Drop-In
Texas Instruments
📦 8-MSOP (VSSOP-8)
Dual differential comparator · 2 channels · 2 V to 36 V · 2 V to 36 V · 300 ns · Open-collector · Rail-to-rail · 0.4 mA typical

Liên hệ để biết giá

Xem tài liệu →

LM2903QPWRQ1

✅ Drop-In
Texas Instruments
📦 8-MSOP (VSSOP-8)
Dual differential comparator · 2 channels · Open-collector, rail-to-rail · 36 V · Single or dual supply · 0.4 mA typical per comparator · 25 nA typical · 3 nA typical

Liên hệ để biết giá

Xem tài liệu →

LM2903DMR2G Tỷ lệ tối đa & tính chất điện

Comparator Type Precision, General Purpose
Number of Channels 2
Response Time / Propagation Delay 1.3 us to 1.5 us (typ)
Supply Voltage Range 2 V to 36 V (single supply)
Input Common-Mode Range Includes ground (V-) level, single supply
Điện áp cung cấp 700 uA (typ)
Kiểu đầu ra Open-Collector, compatible with TTL, MOS, CMOS
Input Bias Current 25 nA to 250 nA class
Khoảng nhiệt độ hoạt động -40C to +105C
Hộp 8-MSOP (Micro8), Case Outline 846A-02
Kiểu lắp đặt Surface Mount
MSL Rating MSL 1 (Unlimited), 260C reflow
Packaging / Container Tape and Reel, 4000 units per reel
Trạng thái RoHS RoHS3 Compliant
REACH Status Unaffected

Cấu hình chân LM2903DMR2G

MSOP-8 Package Pinout Diagram MSOP-8 3x3mm, P0.65mm, JEDEC MO-187. 1 8 2 7 3 6 4 5 MSOP-8
Chân 1 OUT A — Comparator A output (open-collector, requires pull-up)
Chân 2 IN A- — Comparator A inverting input
Chân 3 IN A+ — Comparator A non-inverting input
Chân 4 GND / V- — Ground or negative supply
Chân 5 IN B+ — Comparator B non-inverting input
Chân 6 IN B- — Comparator B inverting input
Chân 7 OUT B — Comparator B output (open-collector, requires pull-up)
Chân 8 VCC / V+ — Positive supply, 2 V to 36 V

Ứng dụng tiêu biểu

LM2903DMR2G phù hợp cho 6 Áp dụngs: Power Supply Undervoltage / Overvoltage Protection, Battery Management and Charging Control, Industrial Sensor Threshold Detection, Automotive Electronics, Relaxation Oscillators and Timing Circuits, Consumer Electronics Level Translation and Detection.

⚡

Power Supply Undervoltage / Overvoltage Protection

The LM2903DMR2G is a natural fit for supply-rail supervision because its 2 V to 36 V supply range tolerates industrial 24 V buses directly and its 700 uA quiescent current adds negligible standby drain to always-on protection circuits. One channel monitors an undervoltage threshold via a resistor divider, while the second channel independently watches for overvoltage, implementing a full window supervisor in a single MSOP-8 package. The 2.0 mV typical input offset keeps the trip point accurate to within millivolts of the divider setting, and the open-collector output drives an optocoupler, relay, or microcontroller interrupt line after pull-up. Designers should add a small amount of hysteresis (a feedback resistor from output to the non-inverting input, typically generating 10-50 mV) to prevent chatter near the threshold, and filter the sense divider against rail noise with a 100 nF capacitor.

🔋

Battery Management and Charging Control

In battery chargers and battery-powered systems, the LM2903DMR2G detects cell voltage thresholds for charge termination, low-battery warning, and discharge cutoff. The -40C to +105C temperature range covers automotive and outdoor equipment enclosures, and the common-mode input range reaching ground allows sensing the low cell of a stack referenced to system ground. The dual channels enable independent charge-complete and fault detection from one package, halving the comparator count of discrete designs. Because battery monitors run continuously, the 700 uA supply current is a direct battery-life saving compared with op-amp-based comparators drawing several milliamps. A typical circuit divides the cell voltage against a TL431 or bandgap reference into the inverting input, with the open-collector output pulling up to the MCU supply, so a 12 V-domain comparator safely signals a 3.3 V microcontroller.

🏭

Industrial Sensor Threshold Detection

Factory automation frequently needs to convert analog sensor outputs - pressure switches, photodiodes, NTC thermistor bridges, current loops - into clean logic signals, and the LM2903DMR2G performs this conversion with 2.0 mV typical offset accuracy and common-mode operation down to ground. Its 1.3 us response time is fast enough for process-level event detection while rejecting fast noise spikes through optional input RC filtering. The wide 36 V supply rating allows direct connection on 24 V industrial panels, simplifying the power architecture where 5 V rails are not present. The two independent channels in one MSOP-8 body consolidate dual-limit monitoring (e.g., pressure high and pressure low) on a single footprint. Open-collector outputs wire-OR conveniently into shared fault buses on PLC I/O boards, and the -40C to +105C rating survives control-cabinet temperature extremes.

🚗

Automotive Electronics

Automotive subsystems - lamp-failure detectors, coolant-level sensors, seat-position switches, and 12 V rail monitors - rely on the LM2903 family's heritage in vehicle environments. The LM2903DMR2G operates from -40C to +105C, spanning underhood-adjacent and cabin modules, and its 2 V to 36 V supply range absorbs the 12 V battery's normal operating excursions within absolute maximum ratings. The ground-sensing common-mode range is valuable in vehicle chassis-referenced circuits where sensor signals swing near 0 V. Open-collector outputs interface directly with ECU logic after pull-up and can share a wired-OR fault line across multiple monitored channels. Designers should verify load-dump conditions with series input resistors, add hysteresis for switch-contact debounce, and follow the onsemi datasheet application circuits for chopper-stabilized level detection in noisy vehicle grounds.

🔧

Relaxation Oscillators and Timing Circuits

The LM2903DMR2G builds simple, robust square-wave and sawtooth oscillators: one channel with a feedback resistor from output to the non-inverting input and an RC network on the inverting input generates relaxation oscillation at frequencies from sub-hertz to roughly the 100 kHz region, bounded by the 1.3 us propagation delay. Such oscillators drive switch-mode LED flashers, charge-pump clocks, watchdog heartbeats, and tone generators in cost-sensitive consumer products. The 700 uA total supply current suits battery-operated timing circuits, and the 36 V rating permits direct operation from rectified high-voltage rails in appliance designs. Compared with the classic 555 timer, the comparator oscillator offers rail-independent output logic via the pull-up and dual channels, letting the second comparator double as a level monitor in the same 8-pin footprint.

📱

Consumer Electronics Level Translation and Detection

Consumer product boards use the LM2903DMR2G for logic-level decision points: detecting tape-end or cover-closed switches, monitoring USB or adapter insertion voltages, and comparing sensor outputs against microcontroller-referenced thresholds. The open-collector output is the key advantage - it lets a circuit powered at one voltage (e.g., a 12 V adapter sense node) produce a clean signal at the MCU's 3.3 V or 5 V domain simply by choosing the pull-up rail, eliminating level-shifter ICs. The MSOP-8 footprint occupies under 15 mm2 of board area, fitting dense handheld and appliance PCBs, while MSL 1 packaging (unlimited floor life) simplifies high-volume SMT assembly logistics. The 2.0 mV typical offset supports accurate discrimination of small adapter-voltage differences, and RoHS3 compliance satisfies global consumer-market environmental regulations.

Tóm tắt các sản phẩm được đề xuất

TL431 Precision shunt reference for comparator thresholds Được sử dụng trong: Power Supply Undervoltage / Overvoltage Protection, Battery Management and Charging Control, Industrial Sensor Threshold Detection, Automotive Electronics, Relaxation Oscillators and Timing Circuits, Consumer Electronics Level Translation and Detection MC3403DR Texas Instruments Được sử dụng trong: Power Supply Undervoltage / Overvoltage Protection, Battery Management and Charging Control, Automotive Electronics TS321IDR Texas Instruments Được sử dụng trong: Industrial Sensor Threshold Detection, Relaxation Oscillators and Timing Circuits, Consumer Electronics Level Translation and Detection
What is the LM2903DMR2G and what are its key specifications?
The LM2903DMR2G is an onsemi dual precision voltage comparator in an 8-pin MSOP (Micro8) package. Key specifications: two independent comparators, 2.0 mV typical input offset voltage, 1.3 us typical response time, 2 V to 36 V single-supply range, 700 uA typical supply current, open-collector TTL/CMOS-compatible outputs, and -40C to +105C operation. According to the onsemi LM2903 datasheet, it belongs to the industry-standard LM393 family for threshold detection in automotive and industrial electronics.
What is the supply voltage range of the LM2903DMR2G?
The LM2903DMR2G operates from a single supply of 2 V to 36 V. According to the onsemi datasheet, operation from split (dual) supplies is also possible as long as the difference between the two supplies is 2 V to 36 V. This wide range allows direct connection to automotive 12 V rails and industrial 24 V systems without a pre-regulator, and the input common-mode range extends down to the ground (V-) level during single-supply operation.
What is the difference between LM2903DMR2G and LM393DMR2G?
Both are onsemi dual comparators in the same MSOP-8 package with identical pinout and open-collector outputs; the main difference is the operating temperature range and grade. The LM2903 device is specified for -40C to +105C, covering the automotive 'A' grade range, while the LM393DMR2G is the general-purpose commercial/industrial version with a narrower temperature range. Electrically, both share the LM393-family architecture, 1.3 us typical response, and 2 V to 36 V supply range, so substitution is straightforward within the temperature requirement.
Can the TI LM2903DGKR replace the onsemi LM2903DMR2G?
Yes, the Texas Instruments LM2903DGKR is a pin-compatible MSOP-8 (VSSOP-8) dual comparator that can replace the onsemi LM2903DMR2G in most designs. Both offer two channels, open-collector outputs, 2 V to 36 V supply range, and approximately 1.3 us propagation delay. Published comparisons of the two parts list matching channel count, output type, and offset class. Verify the pull-up configuration and the exact offset maximum in the TI datasheet before committing a production change, as second-source qualification is always recommended.
What is the best drop-in replacement for the LM2903DMR2G?
The best drop-in replacements are the onsemi LM393DMR2G (same MSOP-8 footprint, same pinout, narrower temperature range) and the Texas Instruments LM2903DGKR (same MSOP-8 footprint, same LM2903 functionality). Both require no PCB changes because the pinout, package, and output stage are identical. If the application operates below 0C or above 85C ambient, prefer the LM2903DGKR, which carries the same -40C to +105C rating as the original part.
Is the LM2903DMR2G suitable for automotive applications?
Yes. The LM2903DMR2G is specified from -40C to +105C, which covers the standard automotive A-grade ambient range, and its 2 V to 36 V supply range tolerates automotive 12 V rail transients such as load-dump clamp levels within the absolute maximum rating. onsemi positions the LM2903 family explicitly for consumer, automotive, and industrial electronics. For safety-critical or AEC-Q100-mandated designs, confirm the specific qualification level with onsemi documentation, since the LM2903 family is a general-purpose rather than a dedicated automotive-qualified series.
Why does the LM2903DMR2G output need a pull-up resistor?
The LM2903DMR2G has open-collector outputs that can only sink current, not source it, so an external pull-up resistor to the desired logic rail is mandatory. Without a pull-up, the output floats and will not present a defined logic level. Choose the resistor for the required rise time and sink current: typical values are 3 k to 15 k. A smaller resistor improves rise time but increases current when the output is low. This arrangement lets a 12 V-powered comparator interface directly to 5 V or 3.3 V TTL or CMOS logic.
What is the response time of the LM2903DMR2G?
The LM2903DMR2G has a typical response time of approximately 1.3 us, with some published specification sheets listing 1.5 us depending on measurement conditions such as input overdrive. This makes the device a general-purpose comparator suited to threshold detection, limit monitoring, and relaxation oscillators at low-to-moderate frequencies, not high-speed applications. For nanosecond-class switching, use a dedicated fast comparator instead; for the LM2903's typical level-sensing roles, the 1.3 us delay is more than adequate.
What is the input offset voltage of the LM2903DMR2G?
The LM2903DMR2G has an input offset voltage specified as low as 2.0 mV per the onsemi datasheet, which is the family's headline precision characteristic. Low offset means the comparator can discriminate small differential signals near its switching threshold, improving accuracy in window comparators and battery-level monitors. For designs requiring tighter threshold accuracy, add external trimming or select a precision comparator family with a sub-millivolt maximum offset specification.
Where to download the LM2903DMR2G datasheet PDF?
Download the LM2903DMR2G datasheet PDF directly from the onsemi product page at onsemi.com under the LM2903 product listing; onsemi publishes the current revision covering the full LM193/LM293/LM393/LM2903 family. The datasheet contains the complete electrical characteristics, absolute maximum ratings, package outline drawing 846A-02 for the MSOP-8, and typical application circuits. Copies are also mirrored on aggregator sites, but the onsemi original is the authoritative, up-to-date source for production design.
Where can I find the LM2903DMR2G pinout?
In the 8-pin MSOP (Micro8) package, the LM2903DMR2G pinout is: pin 1 = Output A, pin 2 = Inverting Input A, pin 3 = Non-Inverting Input A, pin 4 = GND/V-, pin 5 = Non-Inverting Input B, pin 6 = Inverting Input B, pin 7 = Output B, pin 8 = VCC/V+. This follows the standard dual-comparator arrangement of the LM393 family, confirmed in the onsemi datasheet pin description table and the package outline drawing 846A-02.
Is the LM2903DMR2G RoHS compliant?
Yes, the LM2903DMR2G is RoHS3 compliant and REACH unaffected, according to the onsemi product compliance information. The device is also lead-free with an MSL 1 rating (unlimited floor life) and supports 260C lead-free reflow profiles, making it suitable for standard SMT assembly processes without special handling or baking requirements. Compliance documentation is available through the onsemi product page for customer environmental reporting.
What is the supply current of the LM2903DMR2G?
The LM2903DMR2G draws approximately 700 uA of typical supply current for the whole package, independent of how many channels are active, which is the hallmark of the low-power LM393 family. This low quiescent current makes the device suitable for battery-powered monitors, always-on supervisor circuits, and any design where comparator power budget matters. Note that additional current flows through the external output pull-up resistors only when an output is in the low (sinking) state.
Can the LM2903DMR2G operate from a single 5V supply?
Yes, the LM2903DMR2G operates from any single supply between 2 V and 36 V, so a 5 V supply is fully within range. Its key single-supply advantage is that the input common-mode range extends down to ground (V-) level, meaning inputs referenced to 0 V are sensed correctly without a negative rail. In single-supply operation, pin 4 connects to ground, and the open-collector outputs pull up to any logic rail up to the supply rating, typically 5 V for TTL-compatible systems.
Where to buy the LM2903DMR2G and what is the lead time?
The LM2903DMR2G can be ordered through the Request a Quote form on this XAIPART product page; the team will confirm current stock, pricing, and lead time for your required quantity. The part ships in tape-and-reel packaging with 4000 units per reel, and cut tape quantities are typically available for prototype builds. As of the last verification date shown on this page, the device is an active onsemi product in volume production, so lead times are normally standard distribution schedules rather than allocation.

Dữ liệu tham khảo kỹ thuật cho LM2903DMR2G — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the onsemi LM2903DMR2G when you need a dual comparator spanning -40C to +105C in the smallest common footprint (MSOP-8) at low cost - typical cases are automotive 12 V monitors, industrial 24 V threshold detection, and battery supervisors. Choose the LM393DMR2G instead if your ambient never leaves the commercial/industrial range and unit cost dominates; it is the same die in the same package with a narrower temperature rating. Choose the TI LM2903DGKR as a second source when supply-chain dual-sourcing is required - it is footprint-compatible and functionally equivalent, but review its offset specification for precision thresholds. For formally AEC-Q100-mandated automotive platforms, the TI LM2903QPWRQ1 provides Q1 qualification in the same footprint class; confirm body pitch before committing the layout. In all cases the open-collector output and 2 V to 36 V supply range are preserved, so pull-up design carries over unchanged.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này LM393DMR2G LM2903DGKR LM2903QPWRQ1
Package 8-MSOP (Micro8) 8-MSOP (Micro8) - same 8-MSOP (VSSOP-8) - same footprint 8-MSOP (VSSOP-8) - same footprint
Brand onsemi onsemi Texas Instruments Texas Instruments
Number of Channels 2 2 2 2
Supply Voltage Range 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V
Response Time (typ) 1.3 us 1.3 us 1.3 us 1.3 us
Operating Temperature -40C to +105C 0C to +70C class (narrower) -40C to +125C -40C to +125C (AEC-Q100)
Output Type Open-Collector Open-Collector Open-Collector Open-Collector
Automotive Grade No (A-grade temp range) No No Yes (Q1)

Bảo phân biệt quan trọng

  • Extended -40C to +105C automotive A-grade temperature range (vsLM393DMR2G)
  • 2.0 mV typical input offset voltage (vsLM2903DGKR)
  • Dual channels in a 3x3 mm MSOP-8 footprint (vsLM393DMR2G)

Ghi chú thiết kế

The most frequent field failure with this part is omitting the pull-up resistor on the open-collector outputs (pins 1 and 7). Without a pull-up, the output never reaches a defined high level and downstream logic reads floating noise. Always tie each output to its required logic rail through 3 k to 15 k, sized for the sink current (the output can sink roughly 16 mA per the datasheet class) and the required rise time with board capacitance.

Comparators operating near their threshold without hysteresis will chatter on slowly ramping or noisy inputs, producing multiple output transitions. Add positive feedback: connect a resistor (typically 100 k to 1 M) from the output to the non-inverting input to create 10-50 mV of hysteresis, scaling with the pull-up voltage and the feedback divider ratio. Place the hysteresis resistor close to the input pins and keep the reference divider impedance below about 10 k so bias current (up to the 250 nA class) does not shift the trip point.

Place a 100 nF ceramic decoupling capacitor directly across pins 4 and 8 (GND to VCC) within 3 mm of the package, and route the input traces away from switching nodes and clock lines - comparator inputs are high-impedance and will couple millivolt-level errors from adjacent aggressors. For split-supply or high-voltage (up to 36 V) operation, verify creepage clearance on the MSOP-8 pin pitch per your production IPC class. The exposed lead frame of the Micro8 package needs no thermal pad connection; standard solder mask-defined lands per the onsemi 846A-02 outline apply.

Respect the input differential voltage limit: the absolute maximum input differential voltage of the LM2903 family is below the 36 V supply rating, so inputs driven from separate domains (e.g., a 24 V sense node while the comparator runs on 5 V) require series current-limiting resistors. This is the second most common misuse after the missing pull-up and can cause parasitic substrate conduction and latent damage. Consult the absolute maximum ratings table in the onsemi datasheet before interfacing across voltage domains.

Thông tin tuân thủ

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
Không chì
Yes
Không halogen
Unknown
Khoáng vật xung đột
Unknown

RoHS3 compliant, REACH unaffected, MSL 1 (Unlimited) with 260C reflow, per onsemi product compliance information (PartGenie compliance summary).

Dữ liệu được xác minh vào: 2026-11-08 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

LM2903DMR2G datasheet LM2903DMR2G datasheet pdf LM2903DMR2G pinout onsemi LM2903DMR2G LM2903DMR2G equivalent LM2903DMR2G replacement LM2903DMR2G vs LM393DMR2G LM2903DMR2G cross reference LM2903 dual comparator MSOP-8 LM2903DMR2G price LM2903DMR2G stock buy LM2903 low offset voltage dual comparator LM2903 application circuit what is the response time of LM2903DMR2G

Các bộ phận và thuật ngữ liên quan

onsemi LM2903DMR2G LM2903 LM393 LM393DMR2G LM2903DGKR LM2903QPWRQ1 Texas Instruments voltage comparator dual comparator analog comparator amplifier IC open-collector output input offset voltage propagation delay 8-MSOP Micro8 MSOP package family surface mount RoHS REACH MSL 1 automotive electronics industrial automation battery management
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ