LM2904QDR - Dual 26V 700kHz Operational Amplifier | Texas Instruments
MPN: LM2904QDR ✓ Hoạt độngLM2904QDR Tóm tắt
An operational amplifier is an active analog signal-processing component that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. Within the broader hierarchy of analog and mixed-signal integrated circuits, the dual operational amplifier combines two amplifier channels with a shared power supply. The LM2904 family is commonly used where economical, general-purpose amplification is needed rather than high-speed, low-noise, or precision performance.
The LM2904QDR provides two independent amplifier circuits in one 8-pin SOIC package. Its stated 700 kHz gain-bandwidth product supports general-purpose feedback-based signal amplification, while the 26 V maximum supply rating accommodates conventional industrial and automotive-style supply environments. The dual configuration reduces package count when two amplifier channels are required in the same circuit board area.
The operating-temperature range of -40 °C to +125 °C makes the device suitable for temperature-extended industrial equipment, instrumentation, control systems, and vehicle electronics when the surrounding system also meets the required operating limits. The SOIC (D) package also supports conventional surface-mount assembly. Designers should use the manufacturer pin-description table when assigning PCB nets and must account for input common-mode range, output swing, input bias current, noise, and stability requirements in the final signal chain.
Typical uses include sensor-signal conditioning, low-frequency transducer amplification, audio preamplification, voltage buffering, loop filtering, and general industrial control interfaces. In a dual instrumentation circuit, one channel can amplify a sensor output while the other provides buffering, gain, or active filtering. Because the amplifier is intended for general-purpose use, its performance should be checked against the accuracy, bandwidth, noise, and common-mode requirements of the application rather than inferred from the maximum supply rating alone.
For PCB design, keep the feedback network and input nodes compact, provide normal supply bypassing, and avoid long traces that increase parasitic capacitance or pickup. Check whether the selected gain and capacitive loading require additional compensation. Use the manufacturer datasheet for the complete electrical characteristics, recommended operating conditions, pin functions, and application guidance.
This page combines the verified device identity, package information, operating-temperature data, source links, drop-in comparison options, and practical design guidance to support faster component selection and PCB implementation.
Bộ thay thế dễ dàng lắp đặt cho LM2904QDR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2904QDR (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Package, Number of Channels, Common-Mode Input Range, Input Offset Voltage.
LM2904DR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LP2904DR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2904D
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904DG
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904D
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904QDR Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifier Circuits | 2 circuits |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Khoảng nhiệt độ hoạt động | -40 °C to +125 °C |
| Package Type | 8-pin SOIC (D) |
| Số chân | 8 pins |
| Number of Inputs | 4 differential inputs for 2 amplifier channels |
| Số lượng đầu ra | 2 outputs |
| Kiểu lắp đặt | Surface mount |
Cấu hình chân LM2904QDR
| Chân 1 | OUT1 — Output of amplifier channel 1 |
| Chân 2 | IN1- — Inverting input of amplifier channel 1 |
| Chân 3 | IN1+ — Non-inverting input of amplifier channel 1 |
| Chân 4 | V- — Negative power supply or ground connection |
| Chân 5 | IN2+ — Non-inverting input of amplifier channel 2 |
| Chân 6 | IN2- — Inverting input of amplifier channel 2 |
| Chân 7 | OUT2 — Output of amplifier channel 2 |
| Chân 8 | V+ — Positive power supply connection |
Ứng dụng tiêu biểu
LM2904QDR phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Audio Preamplification, Voltage Buffering, Active Loop Filtering, Automotive Control Interfaces, Test and Measurement Equipment.
Industrial Sensor Signal Conditioning
The LM2904QDR fits two-stage industrial sensor conditioning because it provides two amplifier circuits, a 700 kHz gain-bandwidth product, and an operating-temperature range of -40 °C to +125 °C in one 8-pin SOIC package. One channel can amplify a low-level transducer signal while the other buffers or filters it before an ADC. The dual arrangement reduces package count, although the final design must verify the input common-mode range, output swing, input offset, bias current, and noise against the sensor and converter requirements.
Được đề xuất
Audio Preamplification
The LM2904QDR can serve as a general-purpose dual audio preamplifier for low-frequency source signals. Its 700 kHz gain-bandwidth product provides adequate bandwidth for many audio-control and line-level stages, while two channels can handle stereo or separate signal paths. The design should keep the feedback components close to the amplifier, avoid excessive capacitive loading, and verify input offset, noise, output swing, and slew behavior. The 26 V supply rating is useful for higher-voltage analog rails but does not by itself establish low-noise performance.
Được đề xuất
Voltage Buffering
The LM2904QDR is appropriate for buffering sensor outputs or high-impedance analog nodes where dual unity-gain stages are useful. The 700 kHz gain-bandwidth product supports moderate-bandwidth closed-loop operation, and the -40 °C to +125 °C specification covers temperature-extended equipment. In a voltage follower, verify output stability with the source impedance and any cable capacitance, confirm the output can reach the required signal level, and ensure the common-mode input voltage remains inside the valid operating range.
Được đề xuất
Active Loop Filtering
The two LM2904QDR amplifier channels can implement first- or second-order active filters for control, measurement, and interface circuits. A 700 kHz gain-bandwidth product allows useful loop gain well beyond typical low-frequency filter corners, leaving margin for component tolerances and closed-loop shaping. Select the resistor and capacitor values for the required pole and Q, check noise and offset contributions, and confirm that the selected noise gain and capacitive loading remain stable in the manufacturer's recommended operating region.
Được đề xuất
Automotive Control Interfaces
The LM2904QDR's -40 °C to +125 °C rating and dual general-purpose architecture make it a candidate for non-safety-critical vehicle control interfaces, subject to qualification and system requirements. It can condition low-bandwidth sensor signals or provide buffering within a controller subsystem. Automotive use requires checking the exact qualification status, production-change documentation, EMC behavior, load-dump protection at the board level, and input/output limits; the ordering code alone should not be treated as proof of AEC-Q100 qualification.
Được đề xuất
Test and Measurement Equipment
The LM2904QDR can provide general-purpose gain and buffering functions in low-frequency test and measurement equipment. Its dual channels support reusable analog front-end sections, while the 700 kHz gain-bandwidth product is appropriate for instrumentation bandwidths well below that value. Precision measurement designs should evaluate input offset, bias current, noise density, common-mode error, and drift against the measurement uncertainty budget. Stable feedback design and careful grounding are essential when the amplifier drives higher-impedance sources or cable-connected sensors.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2904QDR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2904DR | LP2904DR | LM2904D | LM2904DG | LM2904D |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics | onsemi | Toshiba |
| Package | SOIC-8 (D) | SOIC-8 (D) | SOIC-8 (D) | SOIC-8 | SOIC-8 | SOIC-8 |
| Amplifier Channels | 2 | 2 | 2 | 2 | 2 | 2 |
Bảo phân biệt quan trọng
- Extended temperature capability (vsLP2904DR)
- Two amplifier channels in one package (vsLM324ADR)
- Same-footprint family alternative availability (vsLM2904DG)
- Lower switching frequency for general-purpose signal paths (vsTS974IDT)
Ghi chú thiết kế
Place input, feedback, and decoupling connections so that the amplifier sees low parasitic capacitance and resistance. Connect each supply pin to a low-impedance ground or supply plane through normal bypassing practice, and keep the feedback loop compact. Long input traces can increase noise pickup and input-capacitance effects, while an inadequately grounded supply can shift the apparent output even when the amplifier itself is operating correctly.
Do not assume that a 26 V maximum supply rating permits a 26 V signal at every input and output. Check the recommended supply range, input common-mode range, and output swing against the actual circuit. For dual supplies, confirm the total voltage and the permitted negative supply condition. For single-supply operation, verify the input and output levels can meet the system's minimum signal requirements before committing to the device.
Evaluate closed-loop stability using the selected feedback network, source impedance, load, and PCB capacitance. The 700 kHz gain-bandwidth product is the main speed figure, but practical bandwidth and transient response also depend on gain, noise gain, slew rate, and compensation method. Avoid adding large capacitances directly to an output or high-impedance input node unless the datasheet conditions or a stability analysis support that loading.
The dual SOIC package exposes both amplifier channels to the board's thermal environment. Confirm that both channels are not driving sustained maximum-load conditions at the same time unless the output-current, common-mode, and thermal limits have been checked. Provide copper area around the package and maintain sensible airflow or board placement in enclosed equipment. The SOIC (D) package and -40 °C to +125 °C rating define mechanical and temperature constraints, not a complete thermal design.
Thông tin tuân thủ
The retrieved product information identifies the device and package but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals compliance.