LPC1837JET100E - 180MHz Cortex-M3 MCU | NXP Semiconductors
MPN: LPC1837JET100E ✓ Hoạt độngLPC1837JET100E Tóm tắt
An ARM Cortex-M3 microcontroller is a 32-bit reduced-instruction-computing core designed for embedded control. Within the product hierarchy, the Cortex-M3 is an ARM processor core, while the LPC1837 is a flash-based microcontroller integrating that core with memory, communications, timing, and GPIO resources. The LPC1800 family architecture gives designers a compact platform for connected industrial, communications, consumer, and control applications without requiring a separate external processor for each protocol function.
The LPC1837JET100E combines a maximum CPU frequency of 180 MHz with 1 MB of flash and up to 136 kB of SRAM. Integrated Ethernet supports network-connected equipment, while two high-speed USB interfaces can support host or device peripherals depending on the implemented design. LCD connectivity is also available for human-machine interfaces. These integrated functions reduce system complexity by consolidating communications and display control around one microcontroller.
The 100-TFBGA package is designed for compact, high-density assemblies and provides 100 terminals in a 9 mm by 9 mm footprint. NXP identifies the LPC1837JET100 family as active, and distributor information identifies the LPC1837JET100E as an industrial-temperature part in tray packaging. Because the package uses an area-array layout, PCB design must follow the manufacturer’s land pattern, ball assignments, and multilayer construction requirements rather than treating the device as a conventional leaded package.
Typical uses include industrial Ethernet controllers, USB-connected data-acquisition equipment, networked embedded modules, and compact HMI systems with LCD output. In these applications, the 180 MHz Cortex-M3 core can process protocol and control tasks, the 1 MB flash supports firmware and embedded resources, and the integrated connectivity reduces external component count. Firmware and peripheral configuration should be validated against the complete NXP data sheet and errata before production release.
A critical design step is to use the exact NXP package drawing and pin-multiplexing table for the 100-TFBGA layout. Validate power, ground, decoupling, Ethernet PHY integration, USB routing, and programming access in the PCB stack-up before release. This page combines the available manufacturer and distributor information with engineering-focused selection, application, and integration guidance for the LPC1837JET100E.
Bộ thay thế dễ dàng lắp đặt cho LPC1837JET100E — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LPC1837JET100E (cùng hình factor và footprint) — khác nhau ở Package, Product Type, Maximum CPU Frequency, Mounting Type, Flash Memory.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếLPC1837JET100E Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit ARM Cortex-M3 flash-based microcontroller |
| Maximum CPU Frequency | 180 MHz |
| Processor Core | ARM Cortex-M3 |
| Word Size | 32-bit |
| Flash Memory | 1 MB (1M x 8) |
| SRAM | Up to 136 kB |
| Ethernet | Integrated |
| High-Speed USB Interfaces | 2 |
| LCD Support | Integrated |
| EMC Features | Integrated |
| Điện áp cung cấp | 3.3 V |
| Hộp | 100-TFBGA (9 mm x 9 mm) |
| Terminal Count | 100 terminals |
| Kiểu lắp đặt | Surface-mount ball-grid array |
| Temperature Grade | Industrial |
| Trạng thái vòng đời | Active |
| Maximum Operating Frequency | 180 MHz |
Hướng dẫn cấu hình chân LPC1837JET100E 100-tfbga (9 mm x 9 mm)
Cấu hình chân cho LPC1837JET100E (100-tfbga (9 mm x 9 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho LPC1837JET100E.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LPC1837JET100E phù hợp cho 6 Áp dụngs: Industrial Ethernet Control Systems, USB Data-Acquisition Equipment, Networked Human-Machine Interfaces, Industrial Sensor Gateway, USB Connectivity Hub Controller, Secure Embedded Communications Module.
Industrial Ethernet Control Systems
The LPC1837JET100E fits industrial Ethernet controllers because it combines an ARM Cortex-M3 core rated up to 180 MHz with 1 MB of flash, up to 136 kB of SRAM, and integrated Ethernet connectivity. It can coordinate protocol processing, local control logic, diagnostics, and data handling without requiring a separate communications processor. The 100-TFBGA package also supports compact control assemblies, although designers must follow the exact NXP land pattern and determine the required external Ethernet physical-layer components from the manufacturer documentation.
Được đề xuất
USB Data-Acquisition Equipment
The LPC1837JET100E is suitable for USB-connected measurement and control equipment because it provides two high-speed USB interfaces, a 180 MHz Cortex-M3 core, and 1 MB of flash. Firmware can acquire and process local sensor information while exposing a communications interface to a host system. The 136 kB SRAM ceiling supports moderate buffering and protocol workloads, while the compact 100-TFBGA construction helps reduce board area. USB routing still requires careful impedance control and validation against the selected device configuration.
Được đề xuất
Networked Human-Machine Interfaces
The LPC1837JET100E supports compact human-machine interface controllers by combining LCD connectivity, Ethernet, USB, and substantial on-chip memory. The Cortex-M3 core can manage graphics updates, touch or keypad input, local supervision, and network messaging at up to 180 MHz. Its 1 MB flash capacity provides room for interface firmware and assets, while the 100-TFBGA package helps minimize the footprint. Display timing, electrical levels, and connector protection must be established in the final schematic and PCB design.
Được đề xuất
Industrial Sensor Gateway
The LPC1837JET100E can act as a gateway between local sensors and an Ethernet or USB-based network because it integrates multiple communication interfaces and sufficient flash for embedded protocol firmware. The 180 MHz processor supports concurrent acquisition, filtering, data formatting, and network-stack tasks, while up to 136 kB of SRAM accommodates working buffers. The design must account for the limited RAM budget, use deterministic peripheral assignments, and validate EMC behavior in the target enclosure to maintain reliable industrial operation.
Được đề xuất
USB Connectivity Hub Controller
The LPC1837JET100E is appropriate for intelligent USB hub or embedded connectivity equipment because it provides two high-speed USB interfaces and a high-performance 32-bit core. One USB interface can serve a host connection while the other manages downstream traffic, subject to the device’s supported role and configuration. Its 1 MB flash can retain firmware and configuration data, and the 100-TFBGA package supports compact assemblies. Designers should verify enumeration behavior, power requirements, shared-device limits, and USB signal integrity in the target system.
Được đề xuất
Secure Embedded Communications Module
The LPC1837JET100E can serve as the communications controller in a compact embedded module because Ethernet, two high-speed USB interfaces, LCD support, and EMC features are integrated into one device. The 180 MHz Cortex-M3 core supports networking, protocol translation, local diagnostics, and user-interface tasks, while 1 MB of flash accommodates a substantial firmware image. The module designer should define the intended USB roles, isolate external interfaces appropriately, and implement the required production programming, recovery, and security procedures in firmware.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LPC1837JET100E — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Package | 100-TFBGA (9 mm x 9 mm) |
| Brand | NXP Semiconductors |
| Processor Core | ARM Cortex-M3 |
| Maximum CPU Frequency | 180 MHz |
| Flash Memory | 1 MB (1M x 8) |
| SRAM | Up to 136 kB |
| Ethernet | Integrated |
| High-Speed USB Interfaces | 2 |
| LCD Support | Integrated |
| Supply Voltage | 3.3 V |
| Temperature Grade | Industrial |
| Lifecycle Status | Active |
Bảo phân biệt quan trọng
- Higher flash capacity than the documented LPC1813JET100E option (vsLPC1813JET100E)
- Broader connectivity feature set than the documented LPC1813JET100E option (vsLPC1813JET100E)
- Same 100-TFBGA family geometry with differentiated memory configuration (vsLPC1823JET100E)
Ghi chú thiết kế
Use the exact NXP 100-TFBGA land pattern and recommended PCB stack-up rather than a generic BGA footprint. Confirm ball pitch, pad size, solder-mask definition, paste aperture, via-in-pad policy, and component placement orientation against the package documentation. A 9 mm by 9 mm land pattern can be placed successfully and still fail electrically if escape routing, ground-plane continuity, or assembly rules differ from the manufacturer recommendations.
Route Ethernet and high-speed USB connections as controlled-impedance signals on the stack-up used for production. Keep device escapes short, provide continuous reference planes, avoid unnecessary vias, and observe the interface-specific spacing and via guidance in the manufacturer documentation. Place decoupling capacitors close to the applicable supply balls and keep high-current return paths away from sensitive clock and communication lines.
Plan the 3.3 V supply network around transient response, startup, and the maximum operating conditions of the selected board configuration. Follow the NXP recommended decoupling network and separate sensitive analog or clock supplies where the device provides them. Validate startup sequencing, brownout behavior, and the source-impedance margin against the clocking scheme rather than assuming that a nominal 3.3 V rail alone guarantees stable operation.
Do not substitute an LPC1800 family member solely because it uses a 100-TFBGA package. Confirm the ordering code, temperature suffix, flash size, SRAM configuration, pin multiplexing, USB roles, Ethernet implementation, and boot behavior against the complete manufacturer feature tables. The documented LPC1813JET100E comparison shows 512 KB of flash rather than 1 MB, demonstrating why package similarity alone does not establish drop-in replacement.
Evaluate the assembled PCB as the thermal path for this 100-TFBGA device. Preserve the recommended ground-ball layout and use adequate copper and via distribution beneath and around the package to support heat spreading into the board. Actual junction and case temperatures depend on ambient conditions, copper area, airflow, and operating duty cycle, so use the manufacturer thermal model with the final stack-up and enclosure rather than relying on package dimensions alone.
Thông tin tuân thủ
The retrieved manufacturer excerpt lists environmental-quality information but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. Obtain the current NXP material-compliance record for the exact ordering code.