MAX211IDW - 5V 120kbps RS-232 Transceiver | Texas Instruments
MPN: MAX211IDW ⚠ Lần mua cuốiMAX211IDW Tóm tắt
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into digital logic. Within the interface hierarchy, MAX211IDW is a multichannel RS-232 transceiver built around four RS-232 line drivers, five line receivers, and a dual charge-pump circuit. This topology allows multiple serial channels to share one supply while providing bipolar voltage generation for the driver outputs.
Key features include a 5 V supply, operation to 120 kbit/s, four line drivers, five line receivers, and ±15 kV ESD protection across the serial-port connection pins, including ground. The device is designed to meet the requirements of TIA/EIA-232-F and ITU V.28. Its additional fifth receiver provides flexibility for monitoring a modem handshake signal when the four main driver and receiver channels are already assigned.
The MAX211 architecture uses a dual charge-pump circuit to generate the positive and negative voltages required by RS-232 drivers. Four small external capacitors support charge-pump operation. The resulting interface can place a communication controller on the logic side and a DB9 or other RS-232 connector on the line side without requiring discrete level-shifting circuits. Pin-to-pin ESD protection extends robustness across exposed serial-port connections.
Typical uses include industrial serial-port adapters, data-acquisition equipment, POS terminals, service interfaces, and legacy computer peripherals. The 120 kbit/s operating rate supports moderate-speed asynchronous communication, while the four-driver and five-receiver arrangement is useful for systems requiring several handshake or control lines. The -40°C to +85°C range also suits industrial environments where commercial-temperature interface ICs may be insufficient.
Designers should use the manufacturer's charge-pump capacitor and bypass-capacitor recommendations, place the external capacitors close to their pins, and keep sensitive logic and communications routing separated from exposed connector and ESD paths. The device is marked last-time-buy by a verified distributor listing, so new designs should confirm availability and consider a supported modern interface before committing to a large production run.
This page combines verified manufacturer and distributor information with lifecycle context, drop-in alternatives, comparison parameters, and practical interface-design guidance. It highlights where MAX211IDW remains suitable for multichannel RS-232 and where supply availability or newer USB-to-serial solutions may be more appropriate.
Bộ thay thế dễ dàng lắp đặt cho MAX211IDW — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MAX211IDW (cùng hình factor và footprint) — khác nhau ở Driver Output Swing, Operating Temperature Range, Package, RoHS Status.
MAX211CDW
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX211CDWG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM211ARZ-REEL
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX211IDW Thông số kỹ thuật
| Điện áp cung cấp | 5 V |
| Maximum Data Rate | 120 kbit/s |
| Line Drivers | 4 |
| Line Receivers | 5 |
| ESD Protection | ±15 kV |
| Driver Output Swing | ±9 V |
| Hộp | 28-pin SOIC |
| Khoảng nhiệt độ hoạt động | -40°C to +85°C |
| Kiểu lắp đặt | Surface mount |
| Interface Standard | RS-232 |
| Compliance Standard | TIA/EIA-232-F and ITU V.28 |
| ESD Test Model | Human Body Model |
| ESD Protected Pins | Serial-port connection pins, including GND |
| Charge-Pump Topology | Dual charge-pump circuit |
| External Charge-Pump Capacitors | 4 capacitors |
| Shutdown Supply Current | Low; numerical value not provided |
| Trạng thái RoHS | RoHS3 |
Hướng dẫn cấu hình chân MAX211IDW 28-pin soic
Cấu hình chân cho MAX211IDW (28-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX211IDW.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX211IDW phù hợp cho 6 Áp dụngs: Industrial Serial Port Adapter, Data Acquisition Equipment, Point-of-Sale Terminal Interface, Legacy Computer Peripheral, Communication Controller Interface, RS-232 to RS-485 Gateway.
Industrial Serial Port Adapter
MAX211IDW fits an industrial RS-232 adapter that must translate between a 5 V controller and an exposed DB9 or terminal interface. Its four drivers and five receivers support several data and handshake lines, while the -40°C to +85°C range covers demanding industrial environments. The 120 kbit/s rate is appropriate for legacy configuration and diagnostic protocols rather than high-speed data transfer. Using the fifth receiver for an input-only modem-control signal adds channel flexibility without another transceiver. The ±15 kV ESD protection on serial-port connection pins, including ground, improves robustness when the cable is exposed to user contact or industrial transients.
Được đề xuất
Data Acquisition Equipment
MAX211IDW can provide the legacy control interface between a data-acquisition controller and external laboratory or field equipment. Four driver channels can carry commands or handshake signals, and five receiver channels can accept status, acknowledgment, or monitoring signals. The 120 kbit/s maximum is sufficient for low-bandwidth command traffic but not bulk sensor streaming. The -40°C to +85°C specification supports industrial instrumentation, while ±15 kV ESD protection adds an important layer of protection for externally accessible connector pins. A single dual charge-pump section serves all four drivers, simplifying the power architecture compared with multiple discrete interface devices.
Được đề xuất
Point-of-Sale Terminal Interface
MAX211IDW is appropriate for legacy point-of-sale equipment that still communicates through an RS-232 connector. The four-driver arrangement supports bidirectional data and control traffic, and the fifth receiver can monitor an additional handshake or status line. Its 120 kbit/s rate matches many peripheral-control protocols but requires careful cable and software support for modern point-of-sale networks. ESD protection is especially valuable in retail equipment where the connector may be handled frequently. The -40°C to +85°C range also allows use in kiosks and terminals installed beyond controlled room conditions. Because the verified lifecycle is last-time-buy, product planners should confirm supply before new deployments.
Được đề xuất
Legacy Computer Peripheral
MAX211IDW can preserve an RS-232 connection in legacy computer peripherals, test fixtures, and service equipment that require a direct bipolar serial interface. A modern USB-to-CDC or USB-to-UART bridge is simpler for new designs, but MAX211IDW remains useful when existing equipment expects RS-232 levels and existing cables are already deployed. The 120 kbit/s limit is adequate for configuration, control, and low-speed status transfers. Its four drivers and five receivers support common modem-control arrangements, while the integrated dual charge pump reduces component count. The -40°C to +85°C rating and ±15 kV connector-pin protection improve suitability for long-lived industrial peripherals.
Được đề xuất
Communication Controller Interface
MAX211IDW can connect an asynchronous communication controller to a physical RS-232 port while handling both transmit and receive conversion. The four line drivers generate the required bipolar levels, and the five line receivers restore received signals to logic-compatible levels for the controller. At up to 120 kbit/s, the device suits many control-oriented protocols but does not replace high-speed differential buses such as RS-485. The Texas Instruments documentation identifies TIA/EIA-232-F and ITU V.28 alignment, supporting design confidence for legacy serial communication. Correct implementation still requires appropriate connector grounding, cable design, and appropriate protection for the user environment.
Được đề xuất
RS-232 to RS-485 Gateway
MAX211IDW can serve as the host-facing RS-232 side of a gateway that connects legacy equipment to a longer-distance differential network. The controller uses the four driver and five receiver channels for serial control and handshake functions, while a separate differential transceiver handles the field-side bus. This partitioning is useful when an existing RS-232 host must communicate with modern RS-485 infrastructure. The 120 kbit/s ceiling limits traffic throughput and should be checked against the gateway protocol. ESD protection on exposed serial-port pins improves survival at the host connector, and the -40°C to +85°C range supports industrial enclosure temperatures. The last-time-buy status requires careful procurement planning.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX211IDW — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX211CDW | MAX211CDWG4 | ADM211ARZ-REEL |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices |
| Package | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V |
| Maximum Data Rate | 120 kbit/s | 120 kbit/s | 120 kbit/s | 120 kbit/s |
| Line Drivers | 4 | 4 | 4 | 4 |
| Line Receivers | 5 | 5 | 5 | 5 |
Bảo phân biệt quan trọng
- Verified industrial temperature coverage (vsMAX211CDW)
- Five receivers provide an additional monitoring channel (vsADM211ARZ-REEL)
- Documented 15 kV connector-side ESD protection (vsMAX211CDWG4)
Ghi chú thiết kế
Place the four charge-pump capacitors and the supply bypass capacitor directly beside their associated MAX211IDW pins. Keep the high-voltage RS-232 driver traces away from adjacent logic, clock, and sensitive analog nets. The verified manufacturer description confirms that the charge pump uses four small external capacitors, so following the exact capacitor values and layout in the MAX211 datasheet is necessary to achieve reliable operation.
Route connector-side and charge-pump-node traces conservatively because they can carry switching energy associated with ±9 V driver outputs. Avoid placing test points or long branches directly on charge-pump nodes, and provide a clear return path between the interface ground and connector ground. Keep the logic-side ground reference continuous while respecting the datasheet's guidance on charge-pump capacitor placement.
Do not substitute a modern USB bridge without reviewing the entire communication and power design. MAX211IDW supports legacy RS-232 electrical signaling at up to 120 kbit/s, whereas a USB-to-serial device changes the host interface, connector, driver support, and power requirements. For an actual repair, verify every PCB pin, the 5 V supply, charge-pump capacitors, logic levels, and the connector pinout before fitting a substitute.
Thông tin tuân thủ
The verified distributor listing identifies MAX211IDW as RoHS3. The manufacturer states that the interface meets TIA/EIA-232-F, and the verified listing references ITU V.28. No verified AEC-Q100, REACH, lead-free, halogen-free, or conflict-minerals statements were provided.