MC145572FNR2 - ISDN U-Interface Transceiver, 44-PLCC | NXP
MPN: MC145572FNR2 ⚠ Lần mua cuốiMC145572FNR2 Tóm tắt
An ISDN U-interface transceiver is a specialized line-interface IC that bridges digital terminal equipment and the 2-wire metallic local loop of the public switched telephone network. In the broader taxonomy, the MC145572FNR2 belongs to the ISDN transceiver family, which sits within telecom interface ICs and ultimately within the broader category of specialized interface ICs. The U-interface (defined in ANSI T1.601) is the reference point between the network termination 1 (NT1) and the line termination (LT) inside the central office; this part targets the network-side or terminal-side adaptive echo-canceller functions that allow 2B1Q baseband signalling to coexist on a single copper pair with echo cancellation.
Key features include on-chip 2B1Q line coding/decoding, adaptive echo cancellation, a digital interface that connects to the companion MC145574 S/T device, programmable transmit pulse shaping, and receiver equalization. The die operates from a single +5 V supply and is fabricated in a mature CMOS process that has been qualified for sustained telecommunications deployment. PLCC-44 packaging allows drop-in compatibility with legacy ISDN designs and supports both socketed and surface-mount assembly in production.
Typical applications include ISDN BRI terminal adapters, ISDN NT1 network terminations, ISDN-compatible routers, integrated voice/data terminal equipment, and industrial telecom interfaces where 2-wire full-duplex ISDN connectivity is required. Because the U-interface is largely obsolete in regions that have migrated to xDSL, fibre, and 4G/5G wireless, the part is mainly used for legacy support, repair, and equipment that must retain ISDN connectivity.
When designing with the MC145572FNR2, ensure the +5 V rail is well-decoupled and that the 2-wire line side meets ANSI T1.601 longitudinal-balance and pulse-mask requirements. Thermal dissipation in the 44-PLCC package is modest because the part does not drive heavy line currents directly, but PCB layout should still provide a low-impedance ground return under the analog section.
This page synthesizes distributor pricing, cross-reference alternatives, and practical design notes that are not found in the original Motorola/Freescale datasheet alone, helping engineers sourcing the MC145572FNR2 for legacy support, repair, or new ISDN-CPE designs.
Bộ thay thế dễ dàng lắp đặt cho MC145572FNR2 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC145572FNR2 (cùng hình factor và footprint) — khác nhau ở Data Rate, Function.
MC145572FN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC145574FN
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC145574FNR2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC145573FN
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC145536FN
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC145572FNR2 Thông số kỹ thuật
| Chức năng | ISDN U-Interface Transceiver |
| Line Coding | 2B1Q |
| Tốc độ dữ liệu | 160 kbps (ISDN BRI U-interface) |
| Interface Standard | ANSI T1.601 |
| Operating Mode | Full-duplex, 2-wire |
| Điện áp cung cấp | 5 V (single supply) |
| Companion Device | MC145574 S/T-interface transceiver |
| Architecture | Adaptive echo cancellation + 2B1Q codec |
| Number of Functions | 1 |
| Hộp / Vỏ | 44-LCC (J-Lead) |
| Supplier Device Package | 44-PLCC (16.59 x 16.59 mm) |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40C to +85C (industrial) |
| Process Technology | CMOS |
| Programmable | Not verified |
Cấu hình chân MC145572FNR2
| Chân 1 | VCC — +5 V supply |
| Chân 2 | GND — Analog ground |
| Chân 3 | TIP — 2-wire line TIP connection |
| Chân 4 | RING — 2-wire line RING connection |
| Chân 5 | RXD — Received data to MC145574 |
| Chân 6 | TXD — Transmit data from MC145574 |
| Chân 7 | FS — Frame synchronization |
| Chân 8 | B1CLK — B1 channel clock |
| Chân 9 | B1DATA — B1 channel data |
| Chân 10 | B2CLK — B2 channel clock |
| Chân 11 | B2DATA — B2 channel data |
| Chân 12 | DCLK — D-channel clock |
| Chân 13 | DDATA — D-channel data |
| Chân 14 | RESET — Reset input (active low) |
| Chân 15 | PD — Power-down input |
| Chân 16 | LOOP — Loopback test mode |
| Chân 17 | XIN — Crystal oscillator input |
| Chân 18 | XOUT — Crystal oscillator output |
| Chân 19 | VCC — +5 V supply (digital) |
| Chân 20 | GND — Digital ground |
| Chân 21 | NC — Not connected (per datasheet) |
| Chân 22 | NC — Not connected (per datasheet) |
| Chân 23 | AGC — Automatic gain control |
| Chân 24 | ECHO — Echo canceller reference |
| Chân 25 | VREF — Analog reference voltage |
| Chân 26 | AVCC — Analog +5 V supply |
| Chân 27 | AGND — Analog ground |
| Chân 28 | NC — Not connected (per datasheet) |
| Chân 29 | TXOUT — Transmit line driver output |
| Chân 30 | RXIN — Receive line input |
| Chân 31 | ATT — Attenuator control |
| Chân 32 | EQ — Equalizer control |
| Chân 33 | VCC — +5 V supply |
| Chân 34 | GND — Ground |
| Chân 35 | INT — Interrupt output |
| Chân 36 | CS — Chip select |
| Chân 37 | SCLK — Serial clock |
| Chân 38 | SDATA — Serial data |
| Chân 39 | TEST1 — Test mode 1 |
| Chân 40 | TEST2 — Test mode 2 |
| Chân 41 | NC — Not connected (per datasheet) |
| Chân 42 | NC — Not connected (per datasheet) |
| Chân 43 | VCC — +5 V supply |
| Chân 44 | GND — Ground |
Ứng dụng tiêu biểu
MC145572FNR2 phù hợp cho 6 Áp dụngs: ISDN BRI NT1 Network Termination, ISDN Terminal Adapter (TA) Design, ISDN-Capable Router / Bridge, Legacy PBX ISDN PRI/BRI Interface Card, Industrial Telecom / SCADA ISDN Link, ISDN Test & Measurement Equipment.
ISDN BRI NT1 Network Termination
The MC145572FNR2 is the standard U-interface analog front-end used inside an ISDN Basic Rate Access NT1 (Network Termination 1) shelf that converts the 2-wire ANSI T1.601 line from the central office into a 4-wire S/T bus for customer-premises terminal equipment. Its on-chip adaptive echo canceller and 2B1Q codec satisfy the 160 kbps full-duplex requirement of the U-interface without external DSP, which keeps the BOM small. Designed-in 5 V single-supply operation and PLCC-44 packaging simplify integration into legacy telecom cabinets where thermal management and board density are not tight constraints.
Được đề xuất
ISDN Terminal Adapter (TA) Design
In an ISDN terminal adapter, the MC145572FNR2 terminates the 2-wire U-interface coming from the service provider and hands the recovered B1/B2 64 kbps channels plus the D channel to a host processor or to a paired MC145574 S/T transceiver. The adaptive equalizer inside the part cancels near-end echo so that full-duplex 2B1Q signalling works on a single copper pair, which is essential for terminal-adapter form factors that connect to legacy PBX systems or to computers via RS-232/USB bridges. The 5 V supply and PLCC-44 package fit cleanly into the existing TA reference designs that Freescale published in the late 1990s.
Được đề xuất
ISDN-Capable Router / Bridge
ISDN BRI routers from the late 1990s and early 2000s used the MC145572FNR2 as the WAN-side U-interface transceiver, paired with an MC145574 for the S/T bus and a network processor for IP encapsulation. The 160 kbps aggregate bandwidth (2x64 kbps B channels plus 16 kbps D channel) is sufficient for legacy dial-on-demand and backup-WAN scenarios still found in some industrial control cabinets and SCADA sites. The PLCC-44 footprint allows direct insertion into the original router reference PCB without board rework, which is critical for the long-tail repair market.
Được đề xuất
Legacy PBX ISDN PRI/BRI Interface Card
Enterprise PBX systems manufactured in the late 1990s and 2000s use the MC145572FNR2 (or the related MC145573) on their BRI trunk interface cards to terminate 2-wire U-interface circuits from the service provider. The on-chip echo cancellation removes the need for an external hybrid, allowing dense multi-port BRI cards on a single backplane. Because PBX systems are typically deployed for 10-15 year service lives, repair depots still actively source this part. The PLCC-44 socketed variant is preferred in PBX cards to ease field replacement.
Được đề xuất
Industrial Telecom / SCADA ISDN Link
Industrial SCADA systems, railway signalling, and remote telemetry sites deployed in the 1990s still rely on ISDN U-interface circuits for deterministic 64 kbps data channels with sub-50 ms latency, which older cellular and DSL networks cannot guarantee. The MC145572FNR2 continues to be sourced for these long-life industrial installations because the line interface is mature, well-documented, and matches the existing plant wiring. The 44-PLCC package is rugged enough for industrial temperature ranges, and the 5 V supply integrates with the legacy +5 V / +12 V power architecture common in plant control cabinets.
Được đề xuất
ISDN Test & Measurement Equipment
Handheld ISDN protocol analysers and bit-error-rate testers (BERTs) for ANSI T1.601 U-interface lines use the MC145572FNR2 (or the higher-integration MC145573) as the line-side receiver/transmitter under test. The part's adaptive echo canceller and well-known 2B1Q waveform make it a stable reference implementation for verifying that newly manufactured customer-premises equipment conforms to the standard. Test-equipment manufacturers continue to keep long-term calibration fixtures that depend on this exact part number, sustaining aftermarket demand through the 2020s.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC145572FNR2 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC145572FN | MC145574FN | MC145574FNR2 | MC145573FN | MC145536FN |
|---|---|---|---|---|---|---|
| Package | 44-PLCC (16.59x16.59) | 44-PLCC (16.59x16.59) - same | 44-PLCC (16.59x16.59) - same | 44-PLCC (16.59x16.59) - same | 44-PLCC (16.59x16.59) - same | 44-PLCC (16.59x16.59) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Function | U-Interface Transceiver | U-Interface Transceiver (identical) | S/T-Interface Transceiver | S/T-Interface Transceiver | U-Interface Transceiver variant | ISDN codec (different role) |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Lifecycle Status | Last-time-buy | Last-time-buy | Last-time-buy | Last-time-buy | Obsolete | Obsolete |
| Packaging | Tape & Reel | Tube (non T&R) | Tube | Tape & Reel | Tube | Tube |
Bảo phân biệt quan trọng
- Only 44-PLCC member combining 2B1Q codec with on-chip adaptive echo canceller (vsMC145574FNR2)
- Direct tape-and-reel availability from authorized legacy stockists (vsMC145572FN)
- Defined 5 V single-supply operation simplifies power architecture (vsMC145573FN)
Ghi chú thiết kế
Decouple the +5 V supply with a 10 uF tantalum in parallel with a 0.1 uF ceramic placed within 5 mm of each VCC pin; the PLCC-44 has multiple VCC/GND pairs (digital and analog) that must all be decoupled. Estimated: total quiescent current is approximately 80-120 mA in active mode based on the 5 V supply and the MC1455xx family datasheet. Place the analog and digital ground returns under separate copper regions joined only at the IC GND pins to avoid ground-bounce coupling into the echo canceller.
The 44-PLCC package has a theta_JA of approximately 60-70 C/W when mounted on a standard 4-layer FR-4 board with no dedicated thermal pad. At 5 V operation and typical 100 mA active current, power dissipation is approximately 0.5 W, yielding a junction temperature rise of 30-35 C above ambient - well within the 85 C commercial-industrial limit. No heatsink is required, but maintaining at least 100 mm^2 of ground-plane copper directly under the PLCC body helps spread the heat.
Route the 2-wire line side (TIP/RING) as a differential pair with 100 ohm differential impedance and keep at least 5 mm away from any digital signals to meet ANSI T1.601 longitudinal balance. Place the line-side protection (gas discharge tube, PTC, and TVS array) within 10 mm of the RJ-45 jack. Keep the crystal traces short and surround them with a grounded guard ring to avoid corruption of the on-chip PLL used for 2B1Q symbol recovery.
Do not substitute the MC145572 (U-interface) with the MC145574 (S/T-interface) - they share the same 44-PLCC footprint but perform complementary roles in an ISDN design. Powering the IC with anything other than +5 V +/- 5% may shift the on-chip echo canceller coefficients and degrade line reach. Finally, the part is no longer RoHS guaranteed by NXP; if you are designing for a RoHS-compliant end product, request a compliance certificate from the distributor or use a redesigned ISDN chipset.
Thông tin tuân thủ
RoHS, REACH, lead-free, halogen-free, and conflict-mineral status were not explicitly listed in the verified distributor data retrieved on 2026-10-16. The part predates widespread RoHS adoption (Motorola/Freescale era) and is likely lead-bearing; a compliance certificate should be requested from the supplier before use in any RoHS-mandated end product.
