MC33079DG - 16MHz Low-Noise Quad Op Amp | onsemi
MPN: MC33079DG ✓ Hoạt độngMC33079DG Tóm tắt
An operational amplifier is an active analog component that uses negative feedback to amplify the difference between two input voltages. The quad configuration places four amplifiers in one package, reducing board area for multichannel audio preamplifiers, sensor-conditioning circuits, active filters, and low-level signal-processing systems. The MC33078/79 family uses bipolar circuitry and high-frequency PNP input transistors to combine low input-voltage noise with useful high-frequency performance.
The MC33079DG provides 4.5 nV/sqrt(Hz) voltage-noise density, a 16 MHz gain-bandwidth product, and a 7 V/us slew rate. Its typical harmonic-distortion figure is 0.002%, while common-mode rejection is 80 dB. The low-noise input stage is particularly useful when amplifying weak signals from microphones, sensors, and audio sources without adding unnecessary broadband noise. The output stage supports large voltage swings for improved dynamic range in line-level circuits.
The amplifier's 16 MHz bandwidth makes it suitable for signal paths operating well above the audio band. Its 7 V/us slew rate also allows comparatively rapid transitions when driving higher-impedance loads. The family specification identifies ESD protection of 2 kV, a macromodel for circuit simulation, and excellent frequency stability. These characteristics make the device suitable for precision audio, active filtering, low-level instrumentation, and mixed analog-signal processing.
Typical uses include four-channel audio preamplification, microphone conditioning, active low-pass or band-pass filters, buffered sensor outputs, and general-purpose dual-supply amplification. Because all four amplifiers share one package, PCB space and supply routing can be organized efficiently. The 14-SOIC outline is also convenient for through-hole assembly and conventional prototype-board layouts.
Design with adequate supply decoupling near pins 4 and 11 and confirm that the required output swing remains inside the amplifier's operating limits. The 80 dB common-mode rejection helps reject common-mode interference, but input and output layout still determines actual system noise performance. Avoid excessive capacitive loading because it can reduce stability and alter the practical slew rate.
This product summary combines the manufacturer amplifier specifications, package information, operating limits, drop-in family options, and practical design guidance. It also distinguishes electrical and packaging variants so engineers can identify a suitable replacement without changing the 14-SOIC footprint.
Bộ thay thế dễ dàng lắp đặt cho MC33079DG — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC33079DG (cùng hình factor và footprint) — khác nhau ở Gain-Bandwidth Product, Slew Rate, Amplifier Type, Maximum Supply Voltage, Package.
MC33079D
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC33179D
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC3403D
✅ Drop-In✓ Còn hàng
$0.4102 / Đơn vị
Xem tài liệu →MC33079DR2G
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC33079DG Tỷ lệ tối đa & tính chất điện
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifiers | 4 circuits |
| Technology | Bipolar |
| Gain-Bandwidth Product | 16 MHz |
| Slew Rate | 7 V/us |
| Voltage-Noise Density | 4.5 nV/sqrt(Hz) |
| Harmonic Distortion | 0.002% |
| Common-Mode Rejection Ratio | 80 dB |
| Recommended Dual-Supply Range | +/-2.5 V to +/-9 V |
| Maximum Operating Voltage | +/-18 V |
| Large Output Voltage Swing | V/-14.6 V |
| ESD Protection | 2 kV |
| Hộp | 14-SOIC, 3.90 mm body width |
| Kiểu lắp đặt | Surface mount |
| Circuit Simulation Model | Macromodel included |
Cấu hình chân MC33079DG
| Chân 1 | OUT1 — Amplifier 1 output |
| Chân 2 | IN1- — Amplifier 1 inverting input |
| Chân 3 | IN1+ — Amplifier 1 non-inverting input |
| Chân 4 | V- — Negative supply connection |
| Chân 5 | IN2+ — Amplifier 2 non-inverting input |
| Chân 6 | IN2- — Amplifier 2 inverting input |
| Chân 7 | OUT2 — Amplifier 2 output |
| Chân 8 | OUT3 — Amplifier 3 output |
| Chân 9 | IN3- — Amplifier 3 inverting input |
| Chân 10 | IN3+ — Amplifier 3 non-inverting input |
| Chân 11 | V+ — Positive supply connection |
| Chân 12 | IN4- — Amplifier 4 inverting input |
| Chân 13 | IN4+ — Amplifier 4 non-inverting input |
| Chân 14 | OUT4 — Amplifier 4 output |
Ứng dụng tiêu biểu
MC33079DG phù hợp cho 6 Áp dụngs: Low-Noise Audio Preamplifier, Microphone Signal Conditioning, Active Audio Filters, Industrial Sensor Conditioning, Precision Analog Signal Processing, Data Acquisition Front End.
Low-Noise Audio Preamplifier
The MC33079DG fits low-level audio preamplification because its 4.5 nV/sqrt(Hz) voltage-noise density and 0.002% harmonic-distortion figure support accurate signal amplification with limited added noise and distortion. Each of the four amplifiers can process an independent channel, reducing the number of packages required by a multichannel audio board. Use the device around ±5 V to ±9 V supplies, place supply bypass capacitors near pins 4 and 11, and keep input traces short to preserve the low-noise benefit.
Được đề xuất
Microphone Signal Conditioning
The MC33079DG is appropriate for microphone and low-level instrumentation conditioning where the 4.5 nV/sqrt(Hz) input-noise density can improve the signal-to-noise ratio of weak source signals. Its four channels allow several microphone or sensor paths to share one package while retaining a 16 MHz gain-bandwidth product and 7 V/us slew rate. Connect the non-inverting input to the biased source, the inverting input to the gain-setting network, and verify common-mode range and output swing before selecting the gain.
Được đề xuất
Active Audio Filters
The MC33079DG can implement active low-pass, high-pass, and band-pass filters because its 16 MHz gain-bandwidth product provides useful loop gain above the audio range, while the 7 V/us slew rate supports signal transitions with low distortion. Four independent amplifiers in one 14-SOIC package simplify multi-stage or multi-channel filter layouts. Select component values for the intended closed-loop bandwidth and confirm phase margin using the manufacturer macromodel, particularly for high-Q sections or capacitive loads.
Được đề xuất
Industrial Sensor Conditioning
The MC33079DG can amplify and filter low-level industrial sensor outputs where low input noise, moderate bandwidth, and dual-supply operation are useful. Its 80 dB common-mode rejection helps reduce common-mode disturbance, while four channels can serve multiple transducers or sensing stages. Place the amplifier close to the sensor connector, maintain a quiet ground return, and bypass the supply pins locally. Confirm the sensor output range against the amplifier input common-mode limits before applying gain.
Được đề xuất
Precision Analog Signal Processing
The MC33079DG is suited to general precision analog signal-processing tasks that combine low noise, 80 dB common-mode rejection, and a 16 MHz gain-bandwidth product. Possible circuits include difference amplifiers, gain stages, integrators, and signal conditioners for instrumentation systems. Keep the feedback network close to the relevant amplifier pins and avoid routing high-current return paths beneath the input traces. Verify offset, bias current, and output-current limits from the complete manufacturer specification before finalizing the circuit.
Được đề xuất
Data Acquisition Front End
The MC33079DG can form the analog input-conditioning section of a multichannel data-acquisition system, particularly when signals are small and require amplification before digitization. The four amplifiers provide channel parallelism, 16 MHz closed-loop bandwidth, and 7 V/us slew rate, allowing the same package to perform gain and filtering stages. Use short input paths, solid grounding, and symmetrical layouts across channels to minimize crosstalk. Confirm the acquisition system's input bandwidth, settling requirements, and allowed distortion before choosing the gain.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC33079DG — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC33079D | MC33179D | MC3403D | MC33079DR2G |
|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Number of Amplifiers | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Primary Application | Audio and data signal processing | Audio and data signal processing | Audio and data signal processing | General-purpose amplification | Audio and data signal processing |
Bảo phân biệt quan trọng
- Higher documented gain-bandwidth product within the same onsemi quad-amplifier family (vsMC3403D)
- Low-noise input characteristics are explicitly specified (vsMC33179D)
- Closest same-family electrical and pin configuration (vsMC33079D)
Ghi chú thiết kế
Place the positive and negative supply bypass capacitors close to pins 11 and 4, respectively, and connect them to a low-impedance ground or supply plane. Keep the four amplifier channels physically separated where possible, particularly when one channel handles a weak sensor input and another drives a larger signal. Short feedback traces and symmetrical input routing help prevent channel-to-channel pickup and preserve the device's low 4.5 nV/sqrt(Hz) voltage-noise performance.
Do not assume that every 14-SOIC quad operational amplifier is an exact electrical substitute. Confirm pin functions, input-common-mode range, output swing, input bias current, offset voltage, noise, slew rate, and supply limits in the current manufacturer datasheet. The MC33079D is the closest same-family option, while the MC33179D and MC3403D require careful review of noise, distortion, bandwidth, and output-stage differences.
Use the manufacturer macromodel to evaluate closed-loop stability and frequency response before committing to high-Q active filters. The 16 MHz gain-bandwidth product and 7 V/us slew rate provide substantial speed for audio and instrumentation, but excessive capacitive loading or an unsuitable feedback network can reduce phase margin. Simulate the intended source impedance, load, component tolerances, and supply configuration rather than relying on open-loop bandwidth alone.
Thông tin tuân thủ
The available manufacturer and distributor results do not explicitly state the compliance status of MC33079DG. AEC-Q100 is not applicable because this is a general-purpose operational amplifier rather than an automotive-qualified device.