MC33897EF - 12V Single-Wire CAN Transceiver | NXP | 14-SOIC
MPN: MC33897EF ✓ Hoạt độngMC33897EF Tóm tắt
A single-wire CAN transceiver is an interface IC that converts logic-level controller signals into the electrical signaling required by a single-wire CAN network. Its position in the hierarchy is transceiver → CAN interface IC → interface integrated circuit → semiconductor. This makes the MC33897EF suitable for automotive and industrial networks that use the single-wire CAN physical layer rather than conventional differential CAN.
The device has a 1/1 driver-to-receiver configuration, supports the CAN protocol at its physical layer, and is supplied in a 14-SOIC package. Tube packaging is identified for the MC33897EF. Its lead-free status is identified by the manufacturer, although the complete environmental and qualification details should be confirmed against the relevant product documentation before a regulated design is released.
As a bus interface, the MC33897EF isolates controller-side digital signaling from the physical bus and handles the required electrical conversion between the CAN controller and the wired medium. Designers should pay particular attention to bus termination, grounding, protection, and the distinction between the single-wire CAN signaling method and standard differential CAN implementations.
Typical applications include vehicle body and comfort systems, distributed control modules, sensor interfaces, industrial automation equipment, and embedded diagnostic systems. In each case, a CAN controller handles protocol functions while the MC33897EF provides the physical-layer connection to the single-wire network.
A successful implementation requires checking the controller interface voltage levels, bus topology, termination arrangement, and external protection strategy. The 14-SOIC outline facilitates conventional surface-mount assembly, while good grounding and short signal paths remain important for reliable communication in electrically noisy environments.
This page consolidates the verified device identity, package information, interface configuration, sourcing pathway, comparison limits, and practical design guidance for engineers evaluating the MC33897EF. It also identifies where replacement qualification or additional electrical limits must be completed before schematic release.
Bộ thay thế dễ dàng lắp đặt cho MC33897EF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MC33897AEFR2
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC33897EF Thông số kỹ thuật
| Device Type | Single-wire CAN transceiver |
| Driver/Receiver Configuration | 1 driver / 1 receiver |
| Protocol Support | CAN physical layer |
| Data Link Method | CSMA/CR |
| Nominal Supply Voltage | 12 V |
| Package Type | 14-SOIC |
| Package Width | 3.90 mm (0.154 inch) |
| Kiểu lắp đặt | Surface mount |
| Packaging | Tube |
| Lead-Free Status | Lead-free |
| Số lượng chân | 14 pins |
Hướng dẫn cấu hình chân MC33897EF 3.90 mm (0.154 inch)
Cấu hình chân cho MC33897EF (3.90 mm (0.154 inch) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MC33897EF.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MC33897EF phù hợp cho 6 Áp dụngs: Automotive Body Control Modules, Industrial Sensor Networks, Embedded Diagnostic Systems, Vehicle Sensor Interface Nodes, Distributed Automation Controllers, Single-Wire CAN Communication Modules.
Automotive Body Control Modules
The MC33897EF fits a single-wire CAN body or comfort network where a controller must connect to a 12 V wired medium. Its one-driver, one-receiver arrangement is appropriate for a single physical-layer node, while the 14-SOIC outline supports conventional PCB assembly. The engineer should confirm the complete electrical limits, bus timing, fault behavior, and automotive qualification requirements in the manufacturer documentation. PCB implementation must also account for the external protection and grounding arrangements required by the target vehicle network, because those details materially affect reliability in an electrically demanding environment.
Được đề xuất
Industrial Sensor Networks
The MC33897EF is suitable for an industrial sensor or actuator node connected to a nominal 12 V single-wire CAN network. Its 1/1 transceiver configuration allows one node to transmit and receive on the single-wire physical medium, while the 14-SOIC package simplifies conventional surface-mount assembly. A production design should verify the full operating temperature, supply tolerance, ESD performance, and bus protection requirements. Industrial deployments also require a careful grounding and surge-protection strategy so that wiring faults do not propagate into the controller or the transceiver.
Được đề xuất
Embedded Diagnostic Systems
The MC33897EF can connect a diagnostic controller to a 12 V single-wire CAN medium. The device's single driver and single receiver support normal network communication while leaving the protocol handling to the associated CAN controller. Because diagnostic interfaces may be exposed to service-bay transients and long cable runs, the design must verify transient limits and implement the appropriate external protection. The 14-SOIC package permits assembly alongside the controller and supporting logic, provided that the manufacturer's reference layout and component-spacing guidance are followed.
Được đề xuất
Vehicle Sensor Interface Nodes
The MC33897EF fits remote sensor nodes that communicate over a single-wire CAN bus using a nominal 12 V supply. One transmitter and one receiver are sufficient for a node that participates in the bus rather than repeating it. The engineer should confirm the transceiver's complete input thresholds, output behavior, temperature range, and protection rating before choosing it for a safety- or environment-sensitive vehicle function. PCB placement should minimize loop area, maintain a stable ground reference, and position protection components where they can clamp bus disturbances before they reach the IC.
Được đề xuất
Distributed Automation Controllers
The MC33897EF can provide the physical layer for a distributed automation controller connected to a nominal 12 V single-wire CAN network. Its 1/1 transceiver configuration suits a single communication node, and the 14-SOIC package is compatible with standard surface-mount assembly methods. A robust industrial implementation must address cable-length effects, bus termination, grounding, and fault recovery using the electrical characteristics in the manufacturer datasheet. If the network instead uses CANH and CANL differential signaling, this single-wire device is not electrically interchangeable with a differential transceiver.
Được đề xuất
Single-Wire CAN Communication Modules
The MC33897EF is intended for communication modules that use the single-wire CAN physical layer. Its 12 V nominal supply, single driver, single receiver, and 14-SOIC outline define the core implementation requirements for a compact interface circuit. The controller must be configured for the same single-wire protocol rather than a differential CAN protocol, and the bus network must use the termination arrangement specified for that physical layer. Final release should include checks of logic levels, timing margins, grounding, thermal conditions, and protection behavior against the complete manufacturer documentation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC33897EF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC33897AEFR2 |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 14-SOIC | 14-SOIC |
Bảo phân biệt quan trọng
- Dedicated single-wire CAN physical layer (vsMC33897AEFR2)
- Compact 14-SOIC implementation (vsMC33897AEFR2)
- Tube-packaged production option (vsMC33897AEFR2)
Ghi chú thiết kế
Create the PCB footprint and symbol from the MC33897EF manufacturer package drawing rather than a generic 14-SOIC library item. Confirm pad length, row spacing, lead pitch, and exposed-contact status against the 3.90 mm-wide package identified for this device. Place the transceiver close to the bus connector and protection network, keep the bus trace short, and provide a low-impedance ground path for the interface circuitry.
Do not treat a single-wire CAN transceiver as a drop-in substitute for a differential CANH/CANL device. The bus conductors, termination method, logic levels, protection network, and fault behavior are different. Before layout release, verify the controller interface, supply requirements, bus polarity, termination arrangement, and pin functions against the MC33897EF manufacturer datasheet. This prevents an apparently simple package substitution from causing an unusable network interface.
Route the communications path away from high-current switching nodes and noisy clock or amplifier outputs. Use a continuous ground reference beneath the transceiver area, place input filtering or protection components at the connector boundary, and minimize the loop formed by the bus conductor, protection return, and ground. After schematic completion, review signal return paths and component placement with the controller and power-supply sections in the complete design.
The device is identified as having a nominal 12 V supply, so the power rail must be designed around the complete manufacturer-specified operating and absolute-maximum limits. Include local bypass capacitance close to the supply pins, provide adequate source impedance and transient response, and avoid allowing wiring transients to exceed the device's allowable voltage. Verify startup, reset, and bus-fault behavior in the final system rather than relying on the nominal supply value alone.
Thông tin tuân thủ
The product record identifies MC33897EF as lead-free. RoHS, REACH, halogen-free, conflict-minerals, and automotive qualification details were not established by the available records.