MC908QY1ACDTE - 8-bit HC08 MCU 1.5KB Flash 16-TSSOP | NXP
MPN: MC908QY1ACDTE ✗ Cuối đờiMC908QY1ACDTE Tóm tắt
What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash/ROM), volatile working memory (RAM), peripherals, and digital I/O on one die. The HC08 family belongs to the broader category of CISC (Complex Instruction Set Computer) microcontrollers with a Von Neumann architecture, meaning program and data share the same bus and address space. Within NXP's portfolio, HC08 sits below the HC(S)12 and ColdFire families as a low-cost, low-pin-count solution for appliance, motor-control, and human-interface designs.
Key features of the MC908QY1ACDTE include: 1.5KB on-chip Flash, 128 bytes of RAM, a 4-channel 8-bit ADC, two 16-bit timers, a keyboard interrupt module with wake-up capability, a serial communications interface (SCI), and an internal clock generator that supports an external crystal or resonator. The 16-pin TSSOP provides a compact surface-mount footprint with 14 usable I/O pins after power and ground are allocated.
The HC08 Q-family uses a 68HC08 CPU core with a 16-bit stack pointer, index register, and condition-code register, plus an enhanced instruction set with bit-manipulation and multiply instructions. Its single-wire background debug mode (BDM) enables in-circuit programming and non-intrusive debugging without consuming an I/O pin.
Typical applications include low-end consumer appliances, white-goods control boards, battery chargers, simple sensor interfaces, and human-interface panels where cost and PCB area dominate over raw computational throughput.
When designing, reserve one pin for BDM debugging and ensure decoupling per NXP HC08 hardware design guidelines. The 4.5V-5.5V supply range precludes direct 3.3V operation without a regulator.
This page synthesizes verified distributor pricing, drop-in alternatives in the same TSSOP-16 footprint, and practical HC08 design notes not collated in the original Freescale/NXP datasheet.
Bộ thay thế dễ dàng lắp đặt cho MC908QY1ACDTE — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC908QY1ACDTE (cùng hình factor và footprint) — khác nhau ở ADC, Package, Operating Temperature, I/O Pins, RAM.
MC908QY2ACDTE
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC908QY4ACDTE
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC68HC908QY1CDTE
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC908QY1ACPE
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC908QY1VDTE
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC908QY2CDTER
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC908QY1ACDTE Tỷ lệ tối đa & tính chất điện
| Core Architecture | M68HC08 (CISC, Von Neumann) |
| Program Memory | 1.5 KB Flash |
| RAM | 128 bytes |
| Data EEPROM | 0 bytes (not present on this variant) |
| CPU Bit Width | 8-bit |
| Internal Bus Speed | 32 MHz (8 MHz external osc source) |
| Điện áp cung cấp | 4.5 V to 5.5 V |
| I/O Pins | 14 |
| Hộp | TSSOP-16 (0.65 mm pitch) |
| ADC | 4-channel, 8-bit |
| Timers | 2x 16-bit (TPM) |
| Communication | SCI (UART) |
| Debug Interface | Single-wire BDM |
| Keyboard Interrupt | Yes (KBI with wake-up) |
| Nhiệt độ hoạt động | -40C to +85C |
| Kiểu lắp đặt | Surface Mount |
| Cấp MSL | 3 (per JEDEC J-STD-020) |
| Trạng thái RoHS | Compliant |
Cấu hình chân MC908QY1ACDTE
| Chân 1 | IRQ — External interrupt request input |
| Chân 2 | PTA0/TXD — Port A bit 0 / SCI transmit data |
| Chân 3 | PTA1/RXD — Port A bit 1 / SCI receive data |
| Chân 4 | PTA2 — Port A bit 2 (general-purpose I/O) |
| Chân 5 | PTA3 — Port A bit 3 (general-purpose I/O) |
| Chân 6 | PTA4 — Port A bit 4 (general-purpose I/O) |
| Chân 7 | PTA5 — Port A bit 5 (general-purpose I/O) |
| Chân 8 | VDD — Positive supply voltage (4.5-5.5V) |
| Chân 9 | VSS — Ground |
| Chân 10 | PTB0/AD0 — Port B bit 0 / ADC channel 0 |
| Chân 11 | PTB1/AD1 — Port B bit 1 / ADC channel 1 |
| Chân 12 | PTB2/AD2 — Port B bit 2 / ADC channel 2 |
| Chân 13 | PTB3/AD3 — Port B bit 3 / ADC channel 3 |
| Chân 14 | PTB4 — Port B bit 4 (general-purpose I/O) |
| Chân 15 | PTB5/BDM — Port B bit 5 / Background Debug Mode pin |
| Chân 16 | OSC1 — Crystal oscillator input (external clock source) |
Ứng dụng tiêu biểu
MC908QY1ACDTE phù hợp cho 6 Áp dụngs: Low-End White Goods Control, Battery Charger Controller, Consumer Remote Control, Sensor Interface Module, LED Lighting Controller, Educational / Hobbyist Projects.
Low-End White Goods Control
The MC908QY1ACDTE fits low-end white-goods control boards - washing machines, dishwashers, microwave keypads, and small appliance timers - because its 1.5 KB Flash and 128-byte RAM are sufficient for simple state machines, while its 14 I/O pins can directly drive LED indicators, multiplex 7-segment displays, and read mechanical or Hall-effect sensors. The 32 MHz internal bus rate gives plenty of headroom for capacitive-touch scanning via software timing. The 4.5-5.5V supply aligns with rectified mains-derived rails without a separate regulator, reducing BOM cost.
Được đề xuất
Battery Charger Controller
For simple NiCd/NiMH/Li-ion charger controllers, the MC908QY1ACDTE's 4-channel 8-bit ADC is sufficient to monitor battery voltage and current via external sense resistors, while its 16-bit TPM timers can generate PWM for switch-mode charging regulation. The 4.5-5.5V supply allows direct connection to USB or 5V wall adapters. Single-wire BDM enables in-line firmware updates during manufacturing calibration, eliminating programming sockets.
Được đề xuất
Consumer Remote Control
In IR or RF remote controls the MC908QY1ACDTE serves as the main MCU decoding key presses and producing IR or RF transmission codes. The keyboard interrupt module with wake-up capability lets the MCU run at very low average current, waking only on a key press - a key requirement for coin-cell-powered remotes. Its small TSSOP-16 footprint fits inside slim remote enclosures, and 1.5 KB Flash is plenty for popular transmission protocols like NEC, RC5, or proprietary RF frames.
Được đề xuất
Sensor Interface Module
The MC908QY1ACDTE works well as a stand-alone sensor interface MCU in industrial sensor modules. Its 4-channel ADC converts analog sensor outputs to digital values, while the SCI (UART) communicates upstream to a master controller. The TSSOP-16 footprint fits small sensor housings, and the 4.5-5.5V supply aligns with industrial 5V rails. The keyboard interrupt can be repurposed for edge-triggered events from Hall sensors or rotary encoders.
Được đề xuất
LED Lighting Controller
For dimmable LED controllers and decorative lighting drivers, the MC908QY1ACDTE's two 16-bit TPM timers generate PWM outputs to drive LED current regulators. The 14 I/O pins multiplex control keys, status LEDs, and a TRIAC interface for mains dimming. Flash memory holds default fade curves and color sequences. The HC08's flat address space and bit-manipulation instructions simplify timing-critical loop control.
Được đề xuất
Educational / Hobbyist Projects
The MC908QY1ACDTE is a common teaching and hobbyist microcontroller because its HC08 core is fully documented, the BDM debug interface works with free tools (CodeWarrior HC08), and the TSSOP-16 breakout boards are inexpensive. 1.5 KB Flash is enough for teaching examples (blinking LEDs, keypads, simple games) while still leaving room for student additions. Its enduring popularity means abundant example code and community forum support.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC908QY1ACDTE — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC908QY2ACDTE | MC908QY4ACDTE | MC68HC908QY1CDTE | MC908QY1VDTE | MC908QY2CDTER |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors - same | NXP Semiconductors - same | NXP Semiconductors - same | NXP Semiconductors - same | NXP Semiconductors - same |
| Package | TSSOP-16 | TSSOP-16 - same | TSSOP-16 - same | TSSOP-16 - same | TSSOP-16 - same | TSSOP-16 - same |
| Program Flash | 1.5 KB | 1.5 KB | 4 KB | 1.5 KB | 1.5 KB | 1.5 KB |
| RAM | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 128 bytes |
| Supply Voltage | 4.5-5.5 V | 4.5-5.5 V | 4.5-5.5 V | 4.5-5.5 V | 2.7-3.6 V | 4.5-5.5 V |
| CPU Speed | 8 MHz ext / 32 MHz int | 8 MHz ext / 32 MHz int | 8 MHz ext / 32 MHz int | 8 MHz ext / 32 MHz int | 8 MHz ext / 32 MHz int | 8 MHz ext / 32 MHz int |
| ADC | 4-ch 8-bit | 4-ch 8-bit | 4-ch 8-bit | 4-ch 8-bit | 4-ch 8-bit | 4-ch 8-bit |
| Lifecycle | NRND | Active | Active | NRND / last-time-buy | NRND | Active |
| Unit Price (1pc) | USD 5.20 | USD 4.50 | USD 5.10 | USD 6.10 | USD 5.50 | USD 4.50 |
Bảo phân biệt quan trọng
- Largest memory among NRND-status siblings (vsMC908QY4ACDTE)
- Drop-in upgrade with active lifecycle (vsMC908QY2ACDTE)
- Single-wire BDM debug (vsMC908QY1VDTE)
Ghi chú thiết kế
Place a 100 nF X7R ceramic decoupling capacitor within 5 mm of the VDD pin and a bulk 10 uF tantalum or ceramic capacitor on the same supply rail. The HC908QY1 datasheet specifies that VDD must settle to within 4.5 V to 5.5 V before the reset deassertion timer completes. Use a supervisor IC or built-in COP reset for fail-safe recovery in noisy industrial environments.
Route the single-wire BDM pin (PTB5) to a 2x3 or 1x3 header pad for in-circuit programming access; the pin must be accessible even after conformal coating if you plan field updates. Keep the OSC1/OSC2 traces short (under 5 mm) and surrounded by a ground pour to minimize radiated clock noise into sensitive analog sections sharing the same PCB.
When using PTB0-PTB3 as ADC inputs, add a small RC filter (1 kohm + 100 pF) close to the MCU pin to suppress noise from switching digital signals on adjacent traces. The internal ADC reference is the supply rail; for highest accuracy use the HC908QY2 (which exposes an external VREF pin) or calibrate against a known reference in software.
Do not operate the MC908QY1ACDTE below 4.5 V - the internal clock and Flash read paths fail at lower voltages, producing silent data corruption. If 3.3 V operation is required, choose the MC908QY1VDTE variant instead. Also note that pulling the BDM pin low during reset inadvertently enters background debug mode and prevents normal startup.
Thông tin tuân thủ
RoHS and REACH compliance per NXP environmental information. AEC-Q100 not qualified; HC908QY1 family targets commercial-industrial. Halogen-free status not explicitly stated in NXP material declaration - marked unknown. Conflict-minerals statement available on NXP corporate responsibility page.
