MC9S08GT60ACBE - 8-Bit 40MHz S08 MCU, 60KB Flash | NXP
MPN: MC9S08GT60ACBE ✓ Hoạt độngMC9S08GT60ACBE Tóm tắt
Background context: An 8-bit microcontroller (MCU) is a single-chip computer built around a CPU with an 8-bit data path. The S08 family represents NXP/Freescale's enhanced HC08-architecture line; the MC9S08GT60 sits inside the broader S08GT sub-family of low-cost, high-performance general-purpose 8-bit microcontrollers. Within the taxonomy, this places the part as: 8-bit MCU -> microcontroller -> embedded controller -> semiconductor -> integrated circuit. The HCS08 core is binary-compatible with the legacy HC08 instruction set and adds the BGND instruction for background debug.
Key features include 60 KB (60K x 8) of flash memory for code storage, 4 KB of RAM for data, and a maximum CPU clock frequency of 40 MHz. The device is supplied in a 42-pin SPDIP (Plastic DIP) through-hole package, simplifying prototyping and breadboarding. The supply voltage range spans 2.5 V to 3.3 V per the verified FindIC listing, suitable for battery-backed and low-power industrial nodes.
On the architecture side, the HCS08 core executes most instructions in 1-2 bus cycles and provides up to 32 interrupt/reset sources with vectored interrupt handling. Software-configurable pull-ups on port pins used as inputs remove the need for external resistor networks. Communication peripherals include one SCI (UART), one SPI, and one I2C module, sufficient for sensor hubs, HMI keypads, and simple motor-control front ends.
Typical applications span automotive body electronics, industrial control modules, consumer appliance controllers, and low-end sensor nodes where the 60 KB flash and 4 KB RAM comfortably host state-machine firmware. The wide -40°C to +85°C industrial temperature range also enables outdoor and factory-floor deployments.
When designing with this MCU, allocate decoupling capacitance of 0.1 µF plus 4.7 µF bulk near the VDD/VSS pins, and reserve the BGND pin for in-circuit debugging. Designers should verify pinout against the specific S08GT series datasheet because the 42-pin SPDIP is shared with several siblings at different memory densities.
This page synthesizes distributor pricing, verified parametric data, application guidance, and design notes that complement the manufacturer datasheet for engineers evaluating the MC9S08GT60ACBE.
Bộ thay thế dễ dàng lắp đặt cho MC9S08GT60ACBE — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MC9S08GT60ACBE (cùng hình factor và footprint) — khác nhau ở Mounting Type, Operating Temperature, Package, ADC, Communication Interfaces.
MC9S08GT60ACFBE
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MC9S08GT60ACBDE
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC9S08GT60AVBE
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC9S08GT32ACBE
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MC9S08GT16ACBE
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MC9S08GT60ACBE Tỷ lệ tối đa & tính chất điện
| Core | HCS08 (enhanced HC08, BGND instruction) |
| Bề rộng đường dữ liệu | 8 bit |
| Maximum CPU Clock Frequency | 40 MHz |
| Program Memory Size | 60 KB (60K x 8) FLASH |
| RAM Size | 4 KB |
| Điện áp cung cấp | 2.5 V to 3.3 V |
| Nhiệt độ hoạt động | -40 °C to +85 °C |
| Hộp | 42-Pin PDIP / SPDIP (NDIP), 0.600 in / 15.24 mm |
| Communication Interfaces | 1x SCI (UART), 1x SPI, 1x I2C |
| Interrupt Sources | Up to 32 interrupt/reset sources (per series datasheet) |
| Kiểu lắp đặt | Through-Hole |
| Instruction Set Compatibility | HC08 (binary-compatible) + BGND |
| Family | S08 Family, S08GT Series |
Cấu hình chân MC9S08GT60ACBE
| Chân 1 | PTC0 — Port C I/O bit 0 / [DATA_NEEDED: alternate function] |
| Chân 2 | PTC1 — Port C I/O bit 1 / [DATA_NEEDED: alternate function] |
| Chân 3 | PTC2 — Port C I/O bit 2 / [DATA_NEEDED: alternate function] |
| Chân 4 | PTC3 — Port C I/O bit 3 / [DATA_NEEDED: alternate function] |
| Chân 5 | PTC4 — Port C I/O bit 4 / [DATA_NEEDED: alternate function] |
| Chân 6 | PTC5 — Port C I/O bit 5 / [DATA_NEEDED: alternate function] |
| Chân 7 | VDD — Supply voltage (2.5 V to 3.3 V) |
| Chân 8 | VSS — Ground |
| Chân 9 | PTD0 — Port D I/O bit 0 / [DATA_NEEDED: alternate function] |
| Chân 10 | PTD1 — Port D I/O bit 1 / [DATA_NEEDED: alternate function] |
| Chân 11 | PTD2 — Port D I/O bit 2 / [DATA_NEEDED: alternate function] |
| Chân 12 | PTD3 — Port D I/O bit 3 / [DATA_NEEDED: alternate function] |
| Chân 13 | PTD4 — Port D I/O bit 4 / [DATA_NEEDED: alternate function] |
| Chân 14 | PTD5 — Port D I/O bit 5 / [DATA_NEEDED: alternate function] |
| Chân 15 | PTD6 — Port D I/O bit 6 / [DATA_NEEDED: alternate function] |
| Chân 16 | PTD7 — Port D I/O bit 7 / [DATA_NEEDED: alternate function] |
| Chân 17 | PTE0 — Port E I/O bit 0 / [DATA_NEEDED: alternate function] |
| Chân 18 | PTE1 — Port E I/O bit 1 / [DATA_NEEDED: alternate function] |
| Chân 19 | PTE2 — Port E I/O bit 2 / [DATA_NEEDED: alternate function] |
| Chân 20 | PTE3 — Port E I/O bit 3 / [DATA_NEEDED: alternate function] |
| Chân 21 | PTE4 — Port E I/O bit 4 / [DATA_NEEDED: alternate function] |
| Chân 22 | PTE5 — Port E I/O bit 5 / [DATA_NEEDED: alternate function] |
| Chân 23 | PTE6 — Port E I/O bit 6 / [DATA_NEEDED: alternate function] |
| Chân 24 | PTE7 — Port E I/O bit 7 / [DATA_NEEDED: alternate function] |
| Chân 25 | BKGD — Background Debug Mode (BGND) pin |
| Chân 26 | RESET — Active-low reset input |
| Chân 27 | PTA0 — Port A I/O bit 0 / [DATA_NEEDED: alternate function] |
| Chân 28 | PTA1 — Port A I/O bit 1 / [DATA_NEEDED: alternate function] |
| Chân 29 | PTA2 — Port A I/O bit 2 / [DATA_NEEDED: alternate function] |
| Chân 30 | PTA3 — Port A I/O bit 3 / [DATA_NEEDED: alternate function] |
| Chân 31 | PTA4 — Port A I/O bit 4 / [DATA_NEEDED: alternate function] |
| Chân 32 | PTA5 — Port A I/O bit 5 / [DATA_NEEDED: alternate function] |
| Chân 33 | PTA6 — Port A I/O bit 6 / [DATA_NEEDED: alternate function] |
| Chân 34 | PTA7 — Port A I/O bit 7 / [DATA_NEEDED: alternate function] |
| Chân 35 | PTB0 — Port B I/O bit 0 / [DATA_NEEDED: alternate function] |
| Chân 36 | PTB1 — Port B I/O bit 1 / [DATA_NEEDED: alternate function] |
| Chân 37 | PTB2 — Port B I/O bit 2 / [DATA_NEEDED: alternate function] |
| Chân 38 | PTB3 — Port B I/O bit 3 / [DATA_NEEDED: alternate function] |
| Chân 39 | PTB4 — Port B I/O bit 4 / [DATA_NEEDED: alternate function] |
| Chân 40 | PTB5 — Port B I/O bit 5 / [DATA_NEEDED: alternate function] |
| Chân 41 | PTB6 — Port B I/O bit 6 / [DATA_NEEDED: alternate function] |
| Chân 42 | PTB7 — Port B I/O bit 7 / [DATA_NEEDED: alternate function] |
Ứng dụng tiêu biểu
MC9S08GT60ACBE phù hợp cho 6 Áp dụngs: Automotive Body Electronics, Industrial Sensor Hubs, Consumer Appliance Controllers, HMI Keypad / Display Modules, Low-Power Battery Sensor Nodes, Motor Control Front Ends.
Automotive Body Electronics
The MC9S08GT60ACBE fits automotive body controllers with its 60 KB flash supporting seat-blink FSM models, its 4 KB RAM for CAN-over-SCI bridging buffers, and the -40 to +85 °C industrial range covering cabin modules. The HCS08 core's deterministic 1-2 bus-cycle instruction execution suits real-time window/liftgate tasks, while the integrated SCI/SPI/I2C trio connects directly to body control peripherals without external bridges. The 42-pin SPDIP package simplifies service-replacement modules and field-rework-friendly designs.
Được đề xuất
Industrial Sensor Hubs
For industrial sensor aggregation nodes the MC9S08GT60ACBE provides enough flash (60 KB) to host Modbus-over-SCI or SPI-attached sensor drivers plus 4 KB RAM for sample buffering. The 40 MHz HCS08 core runs typical 10-100 Hz polling loops with ample headroom for filtering. Its 2.5-3.3 V supply range pairs cleanly with 3.3 V sensor ICs. The SPDIP-42 footprint also supports legacy factory PCB layouts where through-hole assembly is still preferred.
Được đề xuất
Consumer Appliance Controllers
White-goods and small-appliance control boards benefit from the MC9S08GT60ACBE's compact 60 KB flash, low 2.5-3.3 V supply, and integrated I2C/SPI for keypad, LED, and temperature-sensor IO. The HCS08 core executes BLDC and PFC state machines in real time, while the part's wide temperature range covers laundry and kitchen environments. The PDIP-42 package accommodates wave-soldered production lines still common in cost-sensitive appliance manufacturing.
Được đề xuất
HMI Keypad / Display Modules
Human-machine interface (HMI) boards with character LCDs, keypads, and rotary encoders pair well with the MC9S08GT60ACBE. The SCI/UART drives mainboard links, SPI clocks LCD controllers, and I2C attaches capacitive-touch or GPIO-expanders. 60 KB flash stores multilingual UI strings and menu logic, while 4 KB RAM holds the display buffer. The 42-PDIP package supports socketed modules for after-market upgrades.
Được đề xuất
Low-Power Battery Sensor Nodes
Battery-powered remote sensor nodes leverage the MC9S08GT60ACBE's S08 Stop and Wait low-power modes plus its 2.5-3.3 V supply range for direct Li-primary or 2xAA operation. The 60 KB flash hosts BLE/Sigfox or LoRa host-driver stub code over SCI/SPI, while 4 KB RAM buffers transmissions between sleep cycles. The 40 MHz CPU wakes, samples, transmits, and returns to sleep quickly enough for years of service on small batteries.
Được đề xuất
Motor Control Front Ends
Small brushless-DC and stepper motor front ends fit the MC9S08GT60ACBE's real-time deterministic core, where the 40 MHz HCS08 executes commutation tables with sub-microsecond jitter. The 60 KB flash holds sinusoidal drive tables and PID gains, while SPI links to smart gate drivers and SCI/UART serves the host controller. The 42-pin PDIP supports legacy motor-control boards through-hole-assembled at low cost.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MC9S08GT60ACBE — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MC9S08GT60ACFBE | MC9S08GT60ACBDE | MC9S08GT60AVBE | MC9S08GT32ACBE | MC9S08GT16ACBE |
|---|---|---|---|---|---|---|
| Package | 42-PDIP / SPDIP (0.600 in) | QFP-44 (surface-mount) | 42-PDIP (same) | 42-PDIP (same) | 42-PDIP (same) | 42-PDIP (same) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Flash Memory | 60 KB | 60 KB | 60 KB | 60 KB | 32 KB (-47%) | 16 KB (-73%) |
| RAM | 4 KB | 4 KB | 4 KB | 4 KB | 2 KB (-50%) | 1 KB (-75%) |
| Core / Max Clock | HCS08 / 40 MHz | HCS08 / 40 MHz | HCS08 / 40 MHz | HCS08 / 40 MHz | HCS08 / 40 MHz | HCS08 / 40 MHz |
| Supply Voltage | 2.5 V to 3.3 V | 2.5 V to 3.3 V | 2.5 V to 3.3 V | 2.5 V to 3.3 V | 2.5 V to 3.3 V | 2.5 V to 3.3 V |
| Operating Temperature | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +105 °C (automotive) | -40 °C to +85 °C | -40 °C to +85 °C |
| Communication Peripherals | 1x SCI, 1x SPI, 1x I2C | 1x SCI, 1x SPI, 1x I2C | 1x SCI, 1x SPI, 1x I2C | 1x SCI, 1x SPI, 1x I2C | 1x SCI, 1x SPI, 1x I2C | 1x SCI, 1x SPI, 1x I2C |
Bảo phân biệt quan trọng
- Largest flash in the S08GT PDIP-42 family (vsMC9S08GT32ACBE)
- Through-hole PDIP-42 form factor simplifies prototyping (vsMC9S08GT60ACFBE)
- HCS08 BGND background debug support (vsMC9S08GT16ACBE)
Ghi chú thiết kế
Place a 0.1 µF ceramic decoupling capacitor as close as possible to each VDD/VSS pair, plus a single 4.7 µF bulk capacitor near the IC. The 2.5-3.3 V supply is sensitive to switching noise, so keep digital supply traces short and avoid routing high-current motor returns near the MCU. For battery-powered designs use the S08 Stop mode to drop quiescent current between events.
The 42-pin SPDIP package has 0.100 in (2.54 mm) pin pitch which is breadboard-compatible. When designing a PCB, route the BKGD and RESET lines with short, direct traces and provide a 10 kΩ pull-up on RESET. Place a 0.1 µF cap on the RESET pin if long cable drives are present. Avoid routing noisy I/O adjacent to the crystal/oscillator pins.
Do not assume the 42-PDIP variants share firmware with the QFP-44 MC9S08GT60ACFBE without verifying the pinout - the QFP package assigns different signals to the extra pins. Also verify the memory map when migrating between 60/32/16 KB flash siblings, because vector table locations and RAM boundaries differ. The 'V' suffix (AVBE) denotes automotive temperature grade (-40 to +105 °C), not a different silicon revision.
Thông tin tuân thủ
RoHS and lead-free status not extracted from the verified web data; check the NXP product page for definitive compliance. Not AEC-Q100 qualified (industrial grade only).
