MCP6022-E/P - Dual 10 MHz Rail-to-Rail Op Amp | Microchip
MPN: MCP6022-E/P ✓ Hoạt độngMCP6022-E/P Tóm tắt
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The MCP6022 contains two amplifier channels in one package, providing a compact solution for filtering, buffering, gain stages, instrumentation, and general-purpose signal conditioning. In the broader power-management hierarchy, the device belongs to the amplifier IC class and is used to condition signals generated by sensors, converters, data-acquisition circuits, and communication equipment.
The MCP6022 family provides rail-to-rail input and output operation, which helps maximize usable signal range in single-supply designs. Its 10 MHz gain-bandwidth product supports moderate-speed amplification, and the reported 8.7 nV/√Hz input-noise density is useful for low-noise signal conditioning. The device also has low distortion, with the family documentation reporting 0.00053% THD+N. The dual configuration reduces board area by integrating two amplifier channels into one package.
Typical applications include sensor signal conditioning, low-voltage audio and communication interfaces, active filters, data converters, portable instrumentation, and industrial control modules. The 2.5 V minimum supply operation is beneficial for battery-powered and embedded systems, where the amplifier must operate directly from a low-voltage rail.
When designing a board around the MCP6022-E/P, check the required input common-mode range, output swing, load drive, stability, and noise performance against the application. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes and high-current return paths.
This product page consolidates verified manufacturer and distributor information, package information, pricing placeholders where verified pricing is unavailable, and engineering-focused selection guidance for the MCP6022-E/P.
Bộ thay thế dễ dàng lắp đặt cho MCP6022-E/P — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MCP6022-E/P (cùng hình factor và footprint) — khác nhau ở Gain-Bandwidth Product, Package, Typical Operating Current.
MCP6022-I/P
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MCP6022-E/P Tỷ lệ tối đa & tính chất điện
| Number of Amplifiers | 2 channels |
| Gain-Bandwidth Product | 10 MHz |
| Typical Operating Current | 1.0 mA per amplifier |
| Maximum Quiescent Current | Less than 1.35 mA per amplifier |
| Input Offset Voltage | Less than 0.5 mV |
| Input Noise Density | 8.7 nV/√Hz |
| THD+N | 0.00053% |
| Minimum Supply Voltage | 2.5 V |
| Maximum Supply Voltage | 5.5 V |
| Khoảng nhiệt độ hoạt động | -40C to +125C |
| Hộp | 8-lead PDIP |
| Kiểu lắp đặt | Through-hole |
| Country of Origin | Thailand |
Hướng dẫn cấu hình chân MCP6022-E/P 8-lead pdip
Cấu hình chân cho MCP6022-E/P (8-lead pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho MCP6022-E/P.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MCP6022-E/P phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Signal Conditioning, Low-Voltage Data Acquisition, Active Audio Filters, Communications Interface Buffering, Industrial Control Signal Conditioning, Portable Instrumentation.
Battery-Powered Sensor Signal Conditioning
The MCP6022-E/P fits low-voltage sensor front ends because its 2.5 V minimum supply and 1.0 mA typical operating current per amplifier suit compact battery-powered systems. Rail-to-rail input and output operation can help preserve signal range when the available supply headroom is limited. A dual amplifier can process one sensor channel or provide gain and filtering for two related signals. Designers should verify the input bias current, common-mode range, and output settling against the sensor impedance, then place supply bypass capacitors close to the package pins to control supply noise.
Được đề xuất
Low-Voltage Data Acquisition
The MCP6022-E/P is useful for amplifying small sensor or divider signals in compact data-acquisition systems because its 10 MHz gain-bandwidth product provides more bandwidth than a strictly low-frequency precision amplifier. The dual package offers channel-to-channel symmetry and reduces component count when two inputs must be conditioned. Input offset below 0.5 mV is also favorable for DC measurements, although the actual accuracy still depends on resistor tolerances, bias-current error, noise, and the chosen noise gain. Keep high-impedance input traces short and shield them from digital switching activity.
Được đề xuất
Active Audio Filters
The MCP6022-E/P can implement active filters and audio preamplifier stages where low voltage, low power, and modest signal bandwidth are more important than high-voltage output swing. Its reported 8.7 nV/√Hz input-noise density and 0.00053% THD+N provide useful starting points for audio signal integrity. The dual amplifier can support stereo or dual-polarity filter sections. Set the closed-loop gain and noise gain conservatively to preserve stability, verify capacitive-load limitations in the datasheet, and use a low-noise output path to avoid degrading the amplifier’s low-noise advantage.
Được đề xuất
Communications Interface Buffering
The MCP6022-E/P is appropriate for buffering and level-conditioning stages in low-voltage communication equipment because it combines rail-to-rail operation, a 10 MHz gain-bandwidth product, and low typical current. The dual channel count allows a transmit and receive path to share one package where channel matching and board area matter. Designers should verify output-current capability, output swing, slew rate, and stability with the intended load and cable capacitance. Route the amplifier close to the interface connector and maintain a continuous return path to minimize ground potential differences.
Được đề xuất
Industrial Control Signal Conditioning
The MCP6022-E/P can condition low-level control signals when the system operates from a 2.5 V to 5.5 V rail and requires two amplifier functions in a compact through-hole package. Its low typical operating current of 1.0 mA per channel reduces demand on constrained power budgets, while the -40C to +125C specification supports extended-temperature equipment. The -40C to +125C rating should be confirmed for the assembled system, along with input protection, output loading, noise, and EMC requirements. Use local filtering and grounding techniques to keep the signal chain immune to switching-node coupling.
Được đề xuất
Portable Instrumentation
The MCP6022-E/P suits portable measurement and instrumentation modules because its 2.5 V operating capability, dual-channel configuration, and 1.0 mA typical current per amplifier support compact, power-constrained designs. The 10 MHz bandwidth can handle moderate-frequency conditioning, while input offset below 0.5 mV supports low-level DC measurements. For portable equipment, evaluate the complete error chain—including sensor noise, input bias current, resistor tolerance, and leakage—rather than relying on offset voltage alone. Keep the analog section physically separated from display, switching-converter, and wireless circuitry.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MCP6022-E/P — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MCP6022-I/P |
|---|---|---|
| Package | 8-lead PDIP | 8-lead PDIP |
| Brand | Microchip Technology | Microchip Technology |
| Number of Amplifiers | 2 channels | 2 channels |
| Gain-Bandwidth Product | 10 MHz | 10 MHz |
| Minimum Supply Voltage | 2.5 V | 2.5 V |
| Maximum Supply Voltage | 5.5 V | 5.5 V |
| Typical Operating Current | 1.0 mA per amplifier | 1.0 mA per amplifier |
| Input Offset Voltage | Less than 0.5 mV | Less than 0.5 mV |
| Input Noise Density | 8.7 nV/√Hz | 8.7 nV/√Hz |
Bảo phân biệt quan trọng
- Extended-temperature identification (vsMCP6022-I/P)
- Dual-channel integration (vsMCP6022-I/P)
- Low-voltage operation with 10 MHz bandwidth (vsMCP6022-I/P)
Ghi chú thiết kế
Plan the dual amplifier's supply budget around the manufacturer-stated typical operating current of 1.0 mA per amplifier and maximum quiescent-current specification of less than 1.35 mA per amplifier. These figures exclude output-current demand and rise with output swing and frequency. Place the required bypass capacitors next to the supply and ground pins, use a low-impedance supply return, and verify startup current if the source has a current limit or slow ramp.
Keep high-impedance input nets short and away from switching nodes, inductors, clock traces, and the underside of noisy power stages. Connect the two channels in a way that minimizes differential ground-potential pickup, particularly in instrumentation circuits. Use a continuous ground reference beneath the analog section and place bypass capacitors at the pins rather than relying on a distant bulk capacitor to supply transient current.
Do not assume that a 10 MHz gain-bandwidth product guarantees 10 MHz closed-loop response at every gain and noise-gain setting. Confirm stability, output swing, slew behavior, load drive, and capacitive-load limits against the manufacturer datasheet. Also verify that the selected MCP6022 temperature grade meets the full system temperature requirement, because the -40C to +125C rating is specifically identified for MCP6022-E/P.
Thông tin tuân thủ
The verified sources confirm an operating temperature range of -40C to +125C and country of origin Thailand, but they do not provide explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statements. AEC-Q100 is marked not_applicable because the product is not identified as an automotive-qualified device in the supplied data.
