MIC4452ZT - 12A Non-Inverting Low-Side MOSFET Driver | Microchip
MPN: MIC4452ZT ✓ Hoạt độngMIC4452ZT Tóm tắt
A MOSFET gate driver is a specialized power-management IC that converts a low-current logic command into the high peak-current charge and discharge pulses required by a power MOSFET gate. In the broader hierarchy, the MIC4452ZT is a gate driver, then a power MOSFET driver, a power management IC, and a semiconductor. Low-side placement means the driver sits on the same supply side as the MOSFET source referenced to ground.
Key verified characteristics include a 12 A peak output, low-side configuration, non-inverting input operation, and approximately 15 ns propagation delay. The manufacturer states that MIC4451 and MIC4452 accept any logic input from 2.4 V up to the supply voltage without external speed-up capacitors or resistor networks. This simplifies control interfaces across different logic-voltage domains.
The CMOS output stage can charge and discharge large MOSFET gates rapidly, reducing switching transition time and associated conduction or switching losses. Its 12 A peak capability provides a substantial drive-current margin over the average gate current required during switching. The MIC4452 is the non-inverting member of the family, whereas MIC4451 uses an inverting input configuration.
Typical uses include DC motor control, power-converter switching, load drivers, and general high-current MOSFET switching. The TO-220-5 construction also offers a larger thermal path than small surface-mount driver packages, although exact junction-temperature and thermal-resistance limits must be taken from the manufacturer datasheet.
Designers should verify absolute maximum voltage, input thresholds, output behavior, and thermal conditions against the official datasheet before production use. Gate resistance, dead time, layout inductance, and the selected MOSFET remain critical to switching performance. The verified material does not provide complete pricing or a complete pin-level mapping, so those details are marked as needed rather than inferred.
Bộ thay thế dễ dàng lắp đặt cho MIC4452ZT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MIC4451ZT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MIC4452YT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TC4452
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TC4452VAT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MIC4452ZT Tỷ lệ tối đa & tính chất điện
| Product Type | Non-inverting low-side CMOS MOSFET gate driver |
| Supply Voltage Range | 4.5 V to 18 V |
| Peak Output Current | 12 A |
| Propagation Delay | 15 ns |
| Input Logic Range | 2.4 V to VS |
| Negative Input Swing Tolerance | Up to 5 V |
| Configuration | Low-side |
| Input Polarity | Non-inverting |
| Process Technology | Bipolar, CMOS, and DMOS process |
| Hộp | TO-220-5 with tab |
| Số lượng chân | 5 pins plus tab |
| Packaging | Tube |
| Kiểu lắp đặt | Through-hole |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân MIC4452ZT to-220-5 with tab
Cấu hình chân cho MIC4452ZT (to-220-5 with tab gói). Động cơ điện này có chân cổng, nguồn và đầu ra. Đối với các gói không phân極, tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết hướng dẫn chính xác của chân 1 và chi tiết về vân footprint. Các ứng dụng phổ biến bao gồm thiết kế nguồn cung cấp điện, điều khiển động cơ và chuyển đổi tải.
Không có dữ liệu chân cụ thể sẵn có cho MIC4452ZT.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MIC4452ZT phù hợp cho 6 Áp dụngs: DC Motor Control, Power Converter Switching, High-Current Load Drivers, Motor Driver Power Stage, Power MOSFET Switching in Industrial Systems, Power Supplies and Output Switching.
DC Motor Control
The MIC4452ZT fits low-side N-channel MOSFET switching in DC motor-control circuits because it provides 12 A peak gate-drive current and non-inverting control. The driver can rapidly charge and discharge the MOSFET gate, reducing transition time and helping the switch reach its intended state efficiently. A controller output can drive the input when its voltage falls within the verified 2.4 V-to-VS input range. Place the driver close to the MOSFET and use a properly sized gate resistor to control edge rate, ringing, and motor-current switching behavior.
Được đề xuất
Power Converter Switching
The MIC4452ZT can drive a low-side power MOSFET in DC-DC converter and power-conversion switching stages where rapid gate transitions and 12 A peak capability are useful. Its CMOS output stage supplies high transient current without requiring external gate speed-up networks, while the 4.5 V to 18 V supply range supports conventional low-voltage power systems. The exact switching frequency, dead time, and MOSFET selection must be verified against the converter design, since the supplied data does not specify those limits.
Được đề xuất
High-Current Load Drivers
For high-current inductive or capacitive loads, the MIC4452ZT provides a non-inverting, low-side MOSFET interface with up to 12 A peak output. This peak current primarily serves the MOSFET gate transition, not a continuous 12 A load rating, so the external MOSFET and copper path determine actual load capability. Use short, wide gate and power traces to minimize parasitic inductance, and select a gate resistor or clamp strategy that limits overvoltage while preserving the required switching speed.
Được đề xuất
Motor Driver Power Stage
The MIC4452ZT is suitable for the switching element of a compact motor-driver power stage when the system uses a non-inverting low-side command. Its 12 A peak output and approximately 15 ns propagation delay help the gate transition respond quickly to controller commands. The device does not determine motor current direction by itself, so flyback paths, braking, and protection must be designed around the MOSFET topology. Validate thermal rise and switching losses for the intended duty cycle.
Được đề xuất
Power MOSFET Switching in Industrial Systems
Industrial control boards often use discrete low-side MOSFET switches for relays, heaters, solenoids, and auxiliary power rails. The MIC4452ZT offers a simple non-inverting interface, 4.5 V to 18 V supply range, and 12 A peak gate-drive capability in a through-hole TO-220-5 package. The package supports mechanical mounting and heat spreading, but the design still needs a suitable MOSFET, adequate copper area, and protection against inductive kickback. Confirm the driver’s operating-temperature limits before deployment.
Được đề xuất
Power Supplies and Output Switching
The MIC4452ZT can be used in power-supply output stages or auxiliary switching circuits where a controller needs more gate current than its I/O pin can provide. Its 12 A peak output helps drive a large MOSFET gate rapidly, while the non-inverting input simplifies connection to suitable logic. The driver’s behavior must be checked against the controller voltage, supply sequencing, and fault conditions. Keep the gate loop compact and account for dead time when multiple switches can conduct during transitions.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MIC4452ZT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MIC4451ZT | MIC4452YT | TC4452 | TC4452VAT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
Bảo phân biệt quan trọng
- Non-inverting control (vsMIC4451ZT)
- Verified 12 A peak output (vsTC4452VAT)
- TO-220-5 through-hole package (vsTC4452)
Ghi chú thiết kế
Place the MIC4452ZT close to the MOSFET gate and power terminals. Keep the gate-drive loop short, use a low-inductance return path, and avoid routing the gate trace through long shared planes. This reduces switching-node ringing and helps the driver’s 12 A peak capability reach the MOSFET efficiently. The tab connection and thermal path must follow the manufacturer package drawing.
The 12 A rating is a peak output capability for charging and discharging the MOSFET gate, not a continuous 12 A regulator or load-current rating. Select the MOSFET, copper traces, connector, and thermal solution for the actual load. For an inductive load, include an appropriate freewheeling path and verify its reverse-voltage stress and switching speed against the driver limits.
Do not assume that any gate driver with similar current capability is pin-compatible. MIC4452ZT is non-inverting, while MIC4451 is the inverting family member. Check the TO-220-5 pin names, tab connection, input thresholds, output polarity, supply range, and absolute maximum ratings in the datasheet before substituting any candidate. The supplied search data does not establish compatibility for TC4452 or TC4452VAT.
Use an external gate resistor to control the switching edge and manage conducted and radiated emissions. Increase resistance when ringing or overshoot is excessive, and reduce it only after checking MOSFET gate voltage, switching loss, and driver capability. A gate-source resistor or other passive clamp may be useful, but its value and voltage rating must be selected from the actual MOSFET and circuit conditions.
Thông tin tuân thủ
The verified PartGenie result states RoHS compliant. REACH, AEC-Q100 status, lead-free status, halogen-free status, and conflict-minerals information are not established by the supplied manufacturer data.
