MP7748SGF - 2x30W Stereo Class D Amplifier | Monolithic Power Systems Inc.
MPN: MP7748SGF ✓ Hoạt độngMP7748SGF Tóm tắt
A Class D audio amplifier is a switching power amplifier that delivers energy to speakers through a continuously switching output stage. Compared with a linear Class A/B amplifier, its practical advantage is lower output-stage dissipation and higher efficiency, although filtering is still required to remove switching-frequency energy. In stereo mode, the MP7748SGF uses two independent single-ended speaker outputs; in mono mode, its outputs can be combined in bridge-tied-load configuration to double the voltage swing delivered to one speaker while avoiding a DC offset across the speaker.
Key verified features include integrated 200 mΩ power MOSFETs, startup and shutdown pop-elimination circuitry, and short-circuit protection. The manufacturer material describes a proprietary variable-frequency topology intended to provide high fidelity comparable to Class A/B amplification. Under 24 V VDD, the manufacturer material states capability for 30 W per channel into a 4 Ω load in single-ended operation and 60 W into an 8 Ω speaker in bridge-tied-load operation. The exposed pad supports heat transfer from the power stage, but thermal performance still depends on PCB copper, layer count, airflow, load duration, and adjacent heat sources.
Typical uses include consumer speakers, multimedia audio, compact stereo systems, sound bars, portable powered speakers, and mono subwoofer or full-range speaker designs. The MP7748SGF is appropriate when local analog amplification is preferred and a Class D efficiency advantage is useful, but it may not suit systems that require a digital input because the verified material identifies an analog-input family.
For layout, follow the manufacturer datasheet connection and thermal recommendations exactly. Keep the exposed-pad thermal path unobstructed, provide adequate input and output filtering, and account for switching-node layout and ground-return control. Do not assume a generic 28-pin footprint or replace the amplifier without checking exposed-pad geometry, pin names, thermal requirements, and load compatibility.
This page consolidates manufacturer specifications, distributor listings, cross-reference evidence, and practical Class D design guidance. Exact pricing, lifecycle status, complete electrical limits, and several physical details were not supplied by the verified sources and are therefore identified rather than guessed.
Bộ thay thế dễ dàng lắp đặt cho MP7748SGF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MP7748SGF (cùng hình factor và footprint) — khác nhau ở Input Type, Package, Stereo Output Power.
MP7748SGF-Z
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MP7748SGF Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Class D audio power amplifier |
| Channel Configuration | 1-channel mono or 2-channel stereo |
| Stereo Output Power | 2 x 30 W into 4 ohm at 24 V VDD |
| Mono Bridge-Tied-Load Output Power | 60 W into 8 ohm at 24 V VDD |
| Alternative Mono Output Power | 50 W into 6 ohm at 24 V VDD |
| Điện áp cung cấp | 24 V VDD cited for stated output-power conditions |
| Output Stage | Integrated 200 mOhm power MOSFETs |
| Cấu trúc | Proprietary variable-frequency Class D topology |
| Protection | Short-circuit protection |
| Startup/Shutdown Feature | Startup and shutdown pop-elimination circuits |
| Hộp | 28-pin TSSOP with exposed pad |
| Kiểu lắp đặt | Surface mount |
| Input Type | Analog audio input |
| Trạng thái RoHS | RoHS compliant |
Hướng dẫn cấu hình chân MP7748SGF 28-pin tssop with exposed pad
Cấu hình chân cho MP7748SGF (28-pin tssop with exposed pad gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho MP7748SGF.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MP7748SGF phù hợp cho 6 Áp dụngs: Compact Stereo Speaker, Mono Bridge-Tied-Load Speaker, Consumer Multimedia Speaker, Powered Sound Bar, Portable Powered Speaker, Analog Audio Subwoofer.
Compact Stereo Speaker
The MP7748SGF fits a compact powered stereo speaker because the manufacturer specifies 2 x 30 W per channel into 4 ohm at 24 V VDD in single-ended operation. Its integrated Class D power stage reduces the external output-component count, while the variable-frequency topology is intended to preserve high-fidelity audio performance. Use the recommended LC output filtering, local supply decoupling, and exposed-pad thermal layout from the manufacturer datasheet. The design must also accommodate amplifier heat and verify that the speaker enclosure and supply can sustain the stated output condition.
Được đề xuất
Mono Bridge-Tied-Load Speaker
For a single speaker, the MP7748SGF can be used in bridge-tied-load configuration, with the manufacturer citing 60 W into 8 ohm at 24 V VDD. BTL doubles the effective output voltage swing compared with a single-ended drive and removes the speaker's DC offset, which is useful in subwoofer and powered-monitor designs. The output network and filter must be designed for bridge operation, and the speaker must tolerate the resulting voltage and power. Confirm thermal conditions and protection behavior in the datasheet.
Được đề xuất
Consumer Multimedia Speaker
The MP7748SGF is suitable for consumer multimedia systems where an analog audio signal must drive stereo speakers efficiently. Its integrated 200 mOhm power MOSFETs, startup/shutdown pop-elimination circuits, and short-circuit protection address common implementation issues in compact powered speakers. The verified 24 V capability should be matched to the system supply rather than inferred from the package. Place filtering and decoupling exactly as recommended, maintain a short return path for power current, and validate audible artifacts across the full volume and startup range.
Được đề xuất
Powered Sound Bar
A sound bar can use the MP7748SGF when it needs efficient stereo amplification in a constrained enclosure and accepts an analog feed. The family's 2 x 30 W stereo capability at 24 V VDD provides a defined design target, while integrated power MOSFETs reduce board area. Sound-bar designs must account for multiple channels, chassis acoustics, idle behavior, and heat spreading across the complete amplifier board. Use the exposed pad as part of the thermal design and validate EMI behavior around the switching output nodes.
Được đề xuất
Portable Powered Speaker
The MP7748SGF can serve as the output stage in a portable powered speaker when its 24 V-class operating condition matches the available supply and the product accepts analog input. Class D operation is useful in portable equipment because it can improve power-conversion efficiency compared with a linear output stage. Battery range, peak-current capability, enclosure temperature, and startup behavior are as important as nominal speaker wattage. The verified material does not identify a portable qualification, so validate those requirements independently.
Được đề xuất
Analog Audio Subwoofer
The MP7748SGF's mono BTL capability makes it relevant for an analog subwoofer or compact full-range speaker enclosure. The manufacturer cites 60 W into 8 ohm at 24 V VDD, which is a useful starting point for enclosure and transformerless speaker matching, although actual output depends on supply, load tolerance, and thermal conditions. A BTL output must not be connected to ground, and the output filter must preserve signal integrity without excessive attenuation. Verify idle offset, protection recovery, and EMI in the finished system.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MP7748SGF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MP7748SGF-Z |
|---|---|---|
| Brand | Monolithic Power Systems | Monolithic Power Systems |
| Package | 28-TSSOP-EP | 28-TSSOP-EP |
| Amplifier Class | Class D | Class D |
| Channel Configuration | Mono or stereo | Mono or stereo |
| Stereo Output Power | 2 x 30 W into 4 ohm at 24 V VDD | 2 x 30 W into 4 ohm at 24 V VDD |
| Mono BTL Output Power | 60 W into 8 ohm at 24 V VDD | 60 W into 8 ohm at 24 V VDD |
| Output Stage | Integrated 200 mOhm power MOSFETs | Integrated 200 mOhm power MOSFETs |
| Protection | Short-circuit protection | Short-circuit protection |
| Startup and Shutdown | Pop-elimination circuits | Pop-elimination circuits |
| Topology | Proprietary variable-frequency Class D | Proprietary variable-frequency Class D |
| Price at Quantity 1 | Not provided | Not provided |
Bảo phân biệt quan trọng
- Single integrated family supports stereo and mono use (vsMP7748SGF-Z)
- Defined high-power output configurations (vsMP7748SGF-Z)
- Integrated protection and startup control (vsMP7748SGF-Z)
Ghi chú thiết kế
Use the exposed pad as a deliberate thermal structure, not merely a footprint feature. Preserve the manufacturer's solder-pad geometry, provide uninterrupted copper beneath the IC, and use the recommended thermal vias and copper spreading pattern. The verified family reaches 2 x 30 W stereo or 60 W mono BTL at 24 V VDD, so validate temperature rise in the actual enclosure and speaker-load duration rather than relying on nominal output power alone.
Place input, supply, ground, and output-filter components according to the manufacturer reference layout. Keep high-current output returns short and keep switching-node copper away from audio input traces. The MP7748S uses a proprietary variable-frequency Class D topology, so layout inductance and return-path discontinuities can increase EMI and audio artifacts. Do not improvise exposed-pad connections or output-filter values without checking the datasheet.
A bridge-tied-load output must never be connected to system ground or to another amplifier output. Confirm whether the design is stereo single-ended or mono BTL before wiring the speaker. Also verify the speaker's minimum impedance, the 24 V supply requirement stated by the manufacturer for the headline power figures, and the availability of startup/shutdown pop suppression. A nominally compatible amplifier can still fail if these system conditions are wrong.
Thông tin tuân thủ
RoHS compliance is stated in the verified distributor search result. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals information were not supplied for the exact MP7748SGF family.
