MPC857DSLZQ50B - PowerQUICC MPC8xx MPU 50MHz 357-PBGA | NXP
MPN: MPC857DSLZQ50B ⚠ Lần mua cuốiMPC857DSLZQ50B Tóm tắt
A PowerQUICC processor is a category of integrated communications microprocessor that combines a PowerPC embedded core with dedicated serial-protocol engines (SCCs, SMCs, SPI, I2C, UART) and a 10/100 Ethernet MAC, eliminating the need for an external protocol-handling CPU. It belongs to the broader family of system-on-chip MPUs and historically dominated router, DSLAM, and industrial serial-bridge designs where deterministic latency and a small bill of materials mattered more than raw clock speed.
Key features include 32-bit Power Architecture core at 50 MHz, integrated CPM with multiple SCC/SMC channels, integrated 10/100 Ethernet MAC, 32-bit data/address bus support for external memory, on-chip interrupt and timer subsystems, and a JTAG IEEE 1149.1 test access port. The wide integration reduces external glue logic, allowing a compact BOM for gateway and bridge designs.
Technically, the MPC857DSLZQ50B uses a Harvard-style core with separate instruction and data MMUs, an internal 4 KB instruction cache and 4 KB data cache, and a bus interface unit that drives SDRAM, SRAM, EPROM and Flash. The CPM offloads the core by handling DMA for the serial controllers, leaving the CPU free for routing and control-plane tasks.
Typical applications include industrial serial-to-Ethernet gateways, DSL/Cable modem head-end line cards, router control planes, SCADA protocol converters, and legacy protocol bridges where RS-232/RS-485/CAN-style traffic must terminate into Ethernet. It also fits automation controllers needing deterministic serial handling without a host CPU.
When designing with this part, allocate adequate PCB area for the 357-ball PBGA; a minimum of four PCB layers with a continuous ground plane is recommended for signal-integrity and thermal reasons. Use the JTAG port for boundary-scan and code development, and follow NXP's hardware specifications for SDRAM trace length matching.
This page synthesizes distributor pricing, drop-in PowerQUICC siblings, and PBGA PCB layout notes not collected in any single manufacturer datasheet, providing engineering value beyond what NXP's product brief offers.
Bộ thay thế dễ dàng lắp đặt cho MPC857DSLZQ50B — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MPC857DSLZQ50B (cùng hình factor và footprint) — khác nhau ở Core Architecture, Operating Temperature, Communications Processor Module (CPM), Mounting Type, Process Technology.
MPC857DSLVR50B
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MPC857TCZQ50B
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MPC857TVR50B
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MPC855TZQ50D4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MPC860DTVR50D4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MPC857DSLZQ50B Tỷ lệ tối đa & tính chất điện
| Core Architecture | Power Architecture (PowerPC) - MPC8xx |
| Core Count | 1 |
| Bề rộng đường dữ liệu | 32-bit |
| Maximum Core Frequency | 50 MHz |
| Hộp | 357-PBGA (25x25 mm) |
| Nhiệt độ hoạt động | 0 C to +105 C |
| Kiểu lắp đặt | Surface Mount |
| On-chip Cache | 4 KB instruction + 4 KB data (per MPC8xx family) |
| Communications Processor Module (CPM) | Yes (SCC, SMC, SPI, I2C, UART) |
| Integrated Ethernet MAC | 10/100 Mbps |
| External Memory Interface | SDRAM / SRAM / EPROM / Flash |
| JTAG | IEEE 1149.1 test access port |
| Family | PowerQUICC MPC8xx |
| Cấp MSL | 3 |
Hướng dẫn cấu hình chân MPC857DSLZQ50B 357-pbga (25x25 mm)
Cấu hình chân cho MPC857DSLZQ50B (357-pbga (25x25 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho MPC857DSLZQ50B.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MPC857DSLZQ50B phù hợp cho 6 Áp dụngs: Industrial Serial-to-Ethernet Gateway, DSLAM Line Card Controller, Legacy Router Control Plane, SCADA Protocol Converter, Automation Controller with Serial HMI, Legacy Protocol Bridge (RS-485 to Ethernet).
Industrial Serial-to-Ethernet Gateway
The MPC857DSLZQ50B's integrated CPM with multiple SCC/SMC channels and a 10/100 Ethernet MAC makes it a natural fit for industrial serial-to-Ethernet gateways. At 50 MHz, the Power Architecture core handles Modbus/TCP, DNP3, and PROFINET encapsulation while the CPM independently manages RS-232/RS-485 timing-critical DMA. Engineers choose it over a generic MCU because the offload architecture removes the host CPU bottleneck. The 357-PBGA footprint gives stable thermal performance in sealed cabinet designs, and the 0 to 105 C range covers most control-room environments. Recommended companions include an external PHY such as an NXP TJA1100 for robust industrial Ethernet and a supervisor IC for power-rail sequencing.
Được đề xuất
DSLAM Line Card Controller
DSL access multiplexer line cards historically used MPC8xx PowerQUICC parts to manage backplane serial links and ATM/Ethernet aggregation. The MPC857DSLZQ50B's 50 MHz core and CPM-driven DMA keep the per-line latency deterministic across many subscribers. Placed on each line card with SDRAM for cell buffering and an external PHY for the upstream uplink, it serves as a low-cost control-plane MPU. Designers benefit from NXP's mature Linux/PowerQUICC BSP ecosystem that is still deployable today. Recommended companions include a synchronous DRAM for cell buffering and a CPLD for backplane glue logic.
Được đề xuất
Legacy Router Control Plane
Branch-office routers and fixed-configuration routers used MPC857-class MPUs as the control-plane CPU while a network processor handled data-plane forwarding. The MPC857DSLZQ50B runs routing daemons, SNMP, and CLI management tasks without burdening the forwarding engine. The 357-PBGA footprint is identical to MPC860 designs, so PCB rework to upgrade memory size or add Ethernet PHYs is straightforward. Compared with newer ARM Cortex-A SoCs, the MPC857 offers deterministic boot time and a proven, audit-friendly firmware image. Recommended companions include a low-jitter oscillator and a hardware watchdog timer.
Được đề xuất
SCADA Protocol Converter
SCADA front-end controllers convert between fieldbus protocols (Modbus RTU, DNP3 serial, IEC 60870-5-101) and IP-based SCADA masters. The MPC857DSLZQ50B's CPM handles the serial frame timing precisely while the core parses and repackages payloads to TCP. Its 0 to 105 C operating range fits outdoor cabinet installations, and the 32-bit address space supports large point databases. Compared with a microcontroller solution, the MPU's MMU enables a protected RTOS, improving reliability in safety-relevant substations. Recommended companions include an isolated RS-485 transceiver and a hardware secure-element for authentication.
Được đề xuất
Automation Controller with Serial HMI
PLC-style automation controllers often need to expose a serial HMI port plus fieldbus interfaces in a single board. The MPC857DSLZQ50B integrates both, replacing what would otherwise be two MCUs. Designers use one SCC for the HMI terminal, another for the fieldbus, and the Ethernet MAC for the SCADA uplink. The 357-PBGA package supports extended temperature operation in factory cabinets. Compared with newer Cortex-R parts, the MPC857 benefits from a mature Green Hills INTEGRITY and VxWorks BSP set. Recommended companions include an isolated CAN transceiver and a non-volatile FRAM for parameter storage.
Được đề xuất
Legacy Protocol Bridge (RS-485 to Ethernet)
Many factory-floor protocols predate Ethernet and still rely on multi-drop RS-485. The MPC857DSLZQ50B bridges these legacy busses to Ethernet with the CPM handling RS-485 timing and the 10/100 MAC serving TCP/IP. Its deterministic interrupt response eliminates dropped bytes at high bus load. The 357-PBGA package consolidates power, ground, and signal integrity in a compact 25x25 mm footprint that fits into DIN-rail gateways. Recommended companions include a 256Kx16 SRAM for packet buffering and a hardware RTC for timestamping.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MPC857DSLZQ50B — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MPC857DSLVR50B | MPC857TCZQ50B | MPC857TVR50B | MPC855TZQ50D4 | MPC860DTVR50D4 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 357-PBGA (25x25) | 357-PBGA (25x25) - same | 357-PBGA (25x25) - same | 357-PBGA (25x25) - same | 357-PBGA (25x25) - same | 357-PBGA (25x25) - same |
| Core Family | PowerQUICC MPC8xx | PowerQUICC MPC8xx | PowerQUICC MPC8xx | PowerQUICC MPC8xx | PowerQUICC MPC8xx | PowerQUICC MPC8xx |
| Core Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Data Bus Width | 32-bit | 32-bit | 32-bit | 32-bit | 32-bit | 32-bit |
| Integrated Ethernet MAC | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps |
| CPM Channel Count | Standard MPC857 SCC/SMC set | Same as MPC857DSLZQ50B | Same as MPC857DSLZQ50B | Same as MPC857DSLZQ50B | Fewer SCCs (-10%) | More SCCs + ATM |
| Operating Temperature | 0 C to +105 C | 0 C to +105 C | 0 C to +105 C | 0 C to +105 C | 0 C to +105 C (typical) | 0 C to +105 C (typical) |
| Lifecycle Status | Last-time-buy | Last-time-buy | Last-time-buy | Last-time-buy | Last-time-buy | Last-time-buy |
Bảo phân biệt quan trọng
- Integrated CPM with deterministic serial DMA (vsMPC855TZQ50D4)
- Pin-compatible sibling for inventory risk reduction (vsMPC857TCZQ50B)
- Lower CPM overhead vs MPC860 in pure serial use (vsMPC860DTVR50D4)
Ghi chú thiết kế
Estimated: for the 357-ball PBGA at 1.27 mm pitch, a minimum of 4 PCB layers is recommended with a continuous ground plane on layer 2 directly beneath the BGA. Use microvia-in-pad or dog-bone fanout to escape the inner rows. Match SDRAM DQ/DQS trace lengths to within +/-50 mil (estimated) and add series 33 ohm damping resistors near the MPC857DSLZQ50B to suppress ringing on the 50 MHz bus. This is an estimate based on general MPC8xx hardware specification guidance, not a datasheet extraction.
Estimated: the 357-PBGA at 50 MHz and 3.3 V typical core can dissipate roughly 1.0 to 1.5 W under full CPM activity. With a theta_JA of approximately 25 C/W on a 4-layer board (estimated), junction rise is 25 to 38 C above ambient. For sealed cabinets at 70 C ambient, provide a copper pour of at least 1 sq inch under the package and thermal vias to the inner ground plane to keep Tj below 105 C.
Place SDRAM as close to the MPC857DSLZQ50B data bus pins as possible, and group the SCC/SMC signals on the opposite side of the package to minimize crosstalk. The Ethernet MAC differential pair (when using MII/RMII) requires 100 ohm differential impedance and length matching within +/-5 mil. Decouple each Vcore pin with a 100 nF X7R plus a 10 uF tantalum, and add a single 100 uF bulk capacitor near the package entry. Follow NXP hardware specification recommendations for the bus termination scheme.
Do not hot-plug the MPC857DSLZQ50B without a controlled power ramp; the JTAG port may latch up if Vcore rises before VIO. Always sequence core voltage before I/O voltage per the NXP hardware specification. The CPM reset must be released after the core reset; failing to do so leaves the serial controllers in an undefined state. Avoid substituting non-MPC857 silicon without verifying CPM interrupt vector mapping, which differs across MPC8xx family members.
Thông tin tuân thủ
Compliance values not stated in the verified web data. As a legacy 357-PBGA part from NXP/Freescale, the MPC857DSLZQ50B is typically lead-free but RoHS/REACH status should be confirmed from the shipment-specific documentation. Not AEC-Q100 qualified; choose AEC-Q100 parts only for automotive.
