Texas Instruments

MSP430F4361IPZ - 16-Bit 8MHz MCU with 24KB Flash | TI

MPN: MSP430F4361IPZ ✓ Hoạt động
3 V Vdss 0.1 uA Id 100-pin LQFP, 14 mm x 14 mm Package 8 MHz Speed 24 KB (24K x 8 + 256 B) Memory
MOQ: 1 |

MSP430F4361IPZ Tóm tắt

The Texas Instruments MSP430F4361IPZ is a mixed-signal 16-bit RISC microcontroller operating at up to 8 MHz, with 24 KB of Flash memory, 1 KB of SRAM, and a 100-pin LQFP package. The device integrates a comparator, SPI and UART interfaces, and a 160-segment LCD driver for embedded control systems requiring substantial mixed-signal integration.

A mixed-signal microcontroller combines a digital processor with analog and communication peripherals on one device. The MSP430F4361 belongs to the MSP430 mixed-signal microcontroller family, a 16-bit RISC architecture designed around low-power embedded control. Its integrated LCD driver is especially useful for segmented instrument panels, while the comparator supports threshold-based sensing and the serial interfaces provide flexible peripheral connectivity.

The MSP430F4361IPZ provides a 125 ns instruction cycle time and an 8 MHz maximum clock. Its five low-power operating modes support battery-powered operation, and the manufacturer documents wake-up from standby in less than 6 us. The device also includes a frequency-locked loop, known as FLL+, which supports stable clocking where precise timing is required. An active mode specification of 1 MHz is listed for operating-current characterization.

The integrated peripherals reduce the component count of a typical control board. A 160-segment LCD controller can drive a display directly, the comparator can perform hardware threshold comparisons, and SPI and UART provide paths to sensors, converters, memories, and service interfaces. These functions make the MCU suitable for metering, industrial panels, portable instruments, and embedded systems where board space and standby power are important considerations.

Typical uses include digital utility meters, programmable laboratory instruments, compact industrial controllers, battery-powered monitors, and sensing systems with local displays. An SPI-connected sensor or external memory can share the same bus with a UART link used for configuration or service communication. The LCD segment count should be checked against the physical display layout before PCB routing because segment and common outputs determine the available display functions.

A key design consideration is preserving low-power behavior across software and board-level decisions. Disable unused peripherals, select the appropriate low-power mode, and avoid floating inputs because they can increase current consumption. PCB layout should preserve the required decoupling arrangement, provide a stable reference and clock implementation, and route sensitive comparator inputs away from fast-switching nodes.

This product page consolidates the manufacturer specifications, exact-ordering information, interface characteristics, application guidance, package details, and verified family alternatives into an engineering-oriented reference. It also highlights practical considerations for firmware power management, LCD implementation, peripheral sharing, and drop-in replacement assessment.

Bộ thay thế dễ dàng lắp đặt cho MSP430F4361IPZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MSP430F4361IPZ (cùng hình factor và footprint) — khác nhau ở Package, SRAM, Serial Interfaces.

Texas Instruments
Package: 100-pin LQFP (PZ), 14 mm x 14 mm
SRAM: 1 KB (1024 B)
Serial Interfaces: SPI and UART/USART
So sánh với MSP430F4361IPZ →

MSP430F4481IPZR

✅ Drop-In
📦 100-LQFP (14 x 14 mm)
Same MSP430x4xx family and 100-LQFP package; exact memory, LCD, and peripheral deltas are not stated

📋 Tham chiếu thay thế (không có trong danh mục)

MSP430F4491IPZR

✅ Drop-In
📦 100-LQFP (14 x 14 mm)
Same MSP430x4xx family and 100-LQFP package; exact memory, LCD, and peripheral deltas are not stated

📋 Tham chiếu thay thế (không có trong danh mục)

MSP430F4361IPZ Tỷ lệ tối đa & tính chất điện

Device Type Mixed-signal 16-bit RISC microcontroller
Tần số xung maksimum 8 MHz
Flash Memory 24 KB (24K x 8 + 256 B)
SRAM 1 KB
CPU Architecture 16-bit RISC
Instruction Cycle Time 125 ns
Integrated Comparator Yes
Serial Interfaces SPI and UART
LCD Segment Drive 160 segments
Clocking Frequency-Locked Loop Plus (FLL+)
Low-Power Modes 5 modes
Standby Wake-Up Time Less than 6 us
Active Mode Characterization Frequency 1 MHz
RAM Retention Off Mode Current 0.1 uA
Điện áp cung cấp 3 V
Hộp 100-pin LQFP, 14 mm x 14 mm
Kiểu lắp đặt Surface mount

Hướng dẫn cấu hình chân MSP430F4361IPZ 100-pin lqfp, 14 mm x 14 mm

Cấu hình chân cho MSP430F4361IPZ (100-pin lqfp, 14 mm x 14 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.

Bảng cấu hình chân 100-pin lqfp, 14 mm x 14 mm cho MSP430F4361IPZ

Không có dữ liệu chân cụ thể sẵn có cho MSP430F4361IPZ.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

MSP430F4361IPZ phù hợp cho 6 Áp dụngs: Digital Utility Meter, Industrial Measurement Panel, Portable Environmental Monitor, Laboratory Instrument, Programmable Control Panel, Low-Power Data Logger.

🔋

Digital Utility Meter

The MSP430F4361IPZ is suitable for utility meters requiring a local segmented display and low-power standby behavior. Its documented 160-segment LCD controller can drive a glass display without a separate display-driver IC, while the 1 KB SRAM supports display buffers and working variables. The 8 MHz CPU and 125 ns instruction cycle provide ample headroom for measurement sequencing, calibration storage, and communication. Five low-power modes and standby wake-up in less than 6 us help reduce energy use between readings. The SPI interface can connect to a metering front end, and UART can provide configuration or data output.

🏭

Industrial Measurement Panel

The MSP430F4361IPZ fits industrial measurement panels that combine sensor input, a segmented display, and service communications. Its integrated comparator supports hardware threshold functions, while SPI and UART permit connection to transducers, isolated communications, and configuration equipment. The 24 KB Flash provides room for application code, calibration tables, and display routines, and the 1 KB SRAM can hold acquisition and processing buffers. Its 100-pin LQFP package also exposes more I/O than a compact mixed-signal MCU, allowing panel-level functions to be consolidated. Use careful analog grounding and guarded sensor traces when placing the comparator and communications circuitry.

🧩

Portable Environmental Monitor

The MSP430F4361IPZ can serve as the control hub for a portable environmental monitor that periodically samples sensors, displays status, and communicates results. The MCU's five low-power modes support duty-cycled operation, while its ability to wake from standby in less than 6 us enables responsive sampling schedules. SPI is suitable for compact sensors and serial memory, and UART can provide a direct connection to a host or radio module. A 160-segment display can show measurements, battery state, and status symbols without adding a display-driver package. Firmware should disable unused interfaces between samples to preserve the low-power benefit promised by the MCU family.

🔧

Laboratory Instrument

The MSP430F4361IPZ is appropriate for compact laboratory instruments that need local readout, control logic, and service connectivity. Its 8 MHz 16-bit RISC processor can execute instrument state machines, calibration routines, and user-interface updates, while the comparator handles simple threshold crossings and the SPI interface connects to precision converters or memories. The 160-segment LCD capability supports numeric and symbolic displays without a separate graphics controller. UART provides a straightforward configuration channel for calibration tools. Because this is a mixed-signal device, maintain clean separation between sensitive measurement paths and digital clock or switching signals on the PCB.

🖥️

Programmable Control Panel

The MSP430F4361IPZ can implement a programmable operator panel with status lamps, buttons, a segmented display, and serial-connected downstream controllers. The integrated LCD driver reduces the component count, while 24 KB of Flash accommodates menu logic, alarm handling, and communication protocols. The comparator can support simple switch-state or analog-threshold functions, and the available I/O in the 100-pin LQFP allows additional panel inputs and outputs. Use the SPI bus for a local codec, memory, or expansion device and UART for a supervisory controller. Validate the display segment mapping and pin multiplexing in firmware before the PCB layout is released.

📡

Low-Power Data Logger

The MSP430F4361IPZ fits a low-power data logger that wakes periodically, acquires sensor information, stores operational data, and presents status on a local LCD. Its 24 KB Flash and 1 KB SRAM support compact logging, buffering, and control code. The SPI interface can connect to serial sensors or external nonvolatile memory, while UART supports configuration retrieval. Five low-power modes let the firmware use shallow sleep during idle intervals and deeper retention states between acquisition events. Standby wake-up in less than 6 us supports responsive timing. Validate Flash write endurance, logging interval, and active-current measurements against the actual battery and sensor load.

What are the key specifications of MSP430F4361IPZ that engineers should know?
The MSP430F4361IPZ is an 8 MHz, 16-bit RISC mixed-signal microcontroller with 24 KB of Flash memory, 1 KB of SRAM, and a 100-pin LQFP package. According to the Texas Instruments product information, it integrates a comparator, SPI and UART interfaces, a 160-segment LCD driver, FLL+ clocking, and five low-power modes. Its 125 ns instruction cycle time supports efficient control workloads, while standby wake-up is specified in less than 6 us.
What is the operating voltage of MSP430F4361IPZ?
The MSP430F4361IPZ operates from a 3 V supply. The exact minimum and maximum supply limits are not stated in the available product summary, so consult the manufacturer datasheet's recommended operating conditions before defining the power rails or calculating regulator tolerances. This is especially important when the MCU shares a supply with sensors, display bias circuits, or communication peripherals.
What memory and processing resources does MSP430F4361IPZ provide?
The MSP430F4361IPZ provides 24 KB of Flash memory, consisting of 24K x 8 plus 256 bytes, and 1 KB of SRAM. Its CPU uses a 16-bit RISC architecture with a documented 125 ns instruction cycle time. According to the Texas Instruments product page, the maximum clock frequency is 8 MHz, giving the device sufficient performance for embedded control, display scanning, and moderate serial-data processing.
Which peripherals are integrated into MSP430F4361IPZ?
The MSP430F4361IPZ integrates a comparator, SPI, UART, and a controller for up to 160 LCD segments. According to the Texas Instruments product page, these peripherals support local sensing, display output, and serial communication without requiring separate interface devices. The exact comparator thresholds, UART electrical characteristics, and LCD output assignments should be selected from the manufacturer pin and electrical-characteristic tables.
Where can I download the MSP430F4361IPZ datasheet PDF?
The official MSP430F4361 product page at Texas Instruments is the preferred starting point for the manufacturer datasheet and supporting documents. The exact-ordering designation MSP430F4361IPZ identifies the 100-pin LQFP version, while the base MSP430F4361 page also lists ordering information, quality data, and related technical resources. Use the pin-description and electrical-characteristic sections to confirm board connections and operating limits.
Where can I find the MSP430F4361IPZ pinout?
The MSP430F4361IPZ pinout is defined by the 100-pin LQFP pin-description table in the Texas Instruments MSP430F4361 documentation. The package is a 14 mm by 14 mm surface-mount LQFP. Verify every LCD segment, common output, analog input, serial signal, clock, reset, power, and ground connection against the exact package drawing before routing the PCB or assigning firmware functions.
Is MSP430F4361IPZ suitable for battery-powered instruments?
The MSP430F4361IPZ is suitable for battery-powered instruments because it provides five low-power modes and a specified standby wake-up time of less than 6 us. Its active mode is also characterized at 1 MHz, and off-mode current with RAM retention is listed as 0.1 uA. Actual battery life depends on the selected clock, LCD duty cycle, analog activity, and firmware wake-up frequency.
When should I choose MSP430F4361IPZ over a smaller MSP430 device?
Choose the MSP430F4361IPZ when the design needs a relatively large LCD, multiple serial functions, 24 KB of Flash, and a substantial 100-pin mixed-signal peripheral set. A smaller MSP430 can be preferable for compact products with fewer display outputs and fewer I/O requirements. This selection favors the larger package only when its integrated LCD driver, comparator, SPI, UART, and memory capacity materially simplify the board.
Can MSP430F4481IPZR replace MSP430F4361IPZ on an existing PCB?
The MSP430F4481IPZR is a same-family candidate, but it must not be treated as an automatic replacement. The available comparison identifies both devices as MSP430 devices while the exact Flash, SRAM, LCD, peripheral, and pin-function differences are not numerically stated. Compare the manufacturer package drawings, pin table, memory configuration, clock settings, and application firmware before approving a substitution.
What can replace MSP430F4361IPZ?
The MSP430F4481IPZR and MSP430F4491IPZR are the same-family candidates identified for comparison with the MSP430F4361IPZ. They are not automatically drop-in replacements because the exact memory capacity, LCD configuration, peripheral differences, and pin assignments must be confirmed. Both use the IPZ family package ordering, but the R suffix identifies reel packaging and does not itself establish electrical equivalence.
Is MSP430F4361IPZ the same as MSP430F4361IPZR?
The MSP430F4361IPZ and MSP430F4361IPZR refer to the same underlying 100-pin LQFP device configuration, with the ordering suffix R indicating reel packaging for the latter. They should have matching electrical characteristics, but the physical packing method differs. Firmware, pinout, and electrical suitability are therefore the same, while handling and reel orientation must be checked during production planning.
MSP430F4361IPZ vs MSP430F4481IPZR - which is better for an LCD meter?
The MSP430F4361IPZ is the better documented choice for an LCD meter requiring a 160-segment display because the Texas Instruments product page explicitly identifies that display capability. The MSP430F4481IPZR may offer additional family resources, but its exact display and memory configuration must be checked. Use the F4361 unless the F4481 provides a specifically required feature, such as greater memory or a different LCD capacity.
MSP430F4361IPZ vs MSP430F4491IPZR - which is better for an industrial controller?
Select the MSP430F4361IPZ when its documented 160-segment LCD controller, 24 KB Flash, 1 KB SRAM, comparator, SPI, and UART satisfy the controller requirements. Consider the MSP430F4491IPZR only after confirming that its memory, display, and peripheral configuration solves an additional requirement. Neither part should be selected from family naming alone because detailed pin and electrical compatibility must be confirmed.
Where can I buy MSP430F4361IPZ and what is its current lead time?
Use the Request a Quote form on this page to request MSP430F4361IPZ availability, current lead time, and order quantities. The listing confirms a 100-pin LQFP device with 24 KB Flash and 1 KB SRAM, but it does not provide a fixed stock position or lead-time commitment. A current quotation is the appropriate way to confirm delivery timing for the exact MPN and package.
What is the price of MSP430F4361IPZ?
The current unit price and volume breaks for MSP430F4361IPZ should be requested through the Request a Quote form on this page. Pricing can vary with order quantity, packaging form, production volume, and supply status, so a static figure would not represent a dependable current quotation. Confirm that the quotation names MSP430F4361IPZ and the 100-pin LQFP package.
Is MSP430F4361IPZ in stock?
Current stock for MSP430F4361IPZ should be confirmed through the Request a Quote form on this page. The device is listed with a 100-pin LQFP package, 24 KB Flash, and 1 KB SRAM, but a listing page alone does not guarantee a current warehouse quantity. A stock confirmation should also identify the packaging format and the requested order quantity.

Dữ liệu tham khảo kỹ thuật cho MSP430F4361IPZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the MSP430F4361IPZ when an embedded product benefits from a 160-segment display, 24 KB of Flash, 1 KB of SRAM, an integrated comparator, SPI, UART, and five low-power modes. It is particularly suitable for utility meters, portable monitors, instrument panels, and programmable controllers that need a capable local interface without a separate display-driver IC. Consider the MSP430F4481IPZR or MSP430F4491IPZR only when a requirement calls for a different memory size, display configuration, or peripheral set from the F4361. A 100-LQFP outline alone is not proof of drop-in compatibility: verify the pin table, LCD mapping, clock configuration, supply limits, and device identifiers. For designs that need fewer display outputs or fewer I/O pins, a smaller MSP430 device may reduce board area and system complexity.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này MSP430F4481IPZR MSP430F4491IPZR
Brand Texas Instruments Texas Instruments Texas Instruments
Package 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm) 100-LQFP (14 x 14 mm)
CPU Architecture 16-bit RISC MSP430 16-bit mixed-signal MCU MSP430 16-bit mixed-signal MCU

Bảo phân biệt quan trọng

  • Large integrated segmented-LCD capability (vsMSP430F4481IPZR)
  • Defined mixed-signal peripheral set (vsMSP430F4491IPZR)
  • Defined memory and processing configuration (vsMSP430F4481IPZR)

Ghi chú thiết kế

Use the five low-power modes as part of the system power architecture rather than treating low-power operation as a firmware afterthought. Disable unused SPI, UART, comparator, LCD, and clock functions before entering standby. Keep the active-state duration and wake-up frequency short where possible, then measure current across startup, acquisition, display update, and sleep phases. The listed 0.1 uA off-mode current with RAM retention and less-than-6-us standby wake-up time provide useful design targets, but the complete battery calculation also includes sensors, pull resistors, and display bias current.

Route power, ground, clock, analog, and LCD signals according to the manufacturer package and layout guidance. Place decoupling capacitors at the supply pins with short, low-inductance connections, and provide a clean return path beneath or near the device ground network. The integrated comparator can be sensitive to switching-node coupling, so keep high-current and high-di/dt traces away from analog inputs. Validate LCD segment and common routing against the glass datasheet because an incorrect segment mapping can create visible artifacts even when the MCU operates correctly.

Do not approve a family member as a drop-in substitute solely because it uses the same 100-LQFP outline. Compare the complete pin table, LCD segment and common mapping, supply limits, clock configuration, memory organization, peripheral multiplexing, and device identifiers. The MSP430F4481IPZR and MSP430F4491IPZR are reasonable review candidates, but their exact electrical and peripheral differences must be confirmed before existing firmware and PCB artwork are reused without modification.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

Compliance status must be confirmed from the manufacturer product page or the specific device's material-declaration documentation.

Dữ liệu được xác minh vào: 2026-11-10 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

MSP430F4361IPZ datasheet MSP430F4361IPZ pinout MSP430F4361IPZ datasheet pdf MSP430F4361IPZ specifications MSP430F4361IPZ equivalent MSP430F4361IPZ replacement MSP430F4361IPZ vs MSP430F4481IPZR MSP430F4361IPZ vs MSP430F4491IPZR MSP430F4361IPZ price MSP430F4361IPZ stock Texas Instruments MSP430F4361IPZ MSP430F4361IPZ 100 LQFP MSP430F4361IPZ LCD application MSP430F4361IPZ schematic

Các bộ phận và thuật ngữ liên quan

Texas Instruments MSP430F4361IPZ MSP430F4361 MSP430F4481IPZR MSP430F4491IPZR MSP430x4xx mixed-signal microcontroller microcontroller embedded processor semiconductor 16-bit RISC architecture Frequency-Locked Loop Plus FLL+ SPI UART LCD controller 160-segment LCD comparator Flash memory SRAM LQFP-100 100-pin LQFP surface-mount package low-power mode standby wake-up
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ