PIC16F723T-I/MV - 28-Pin XLP 8-Bit MCU, 7KB Flash | Microchip
MPN: PIC16F723T-I/MV ✓ Hoạt độngPIC16F723T-I/MV Tóm tắt
An 8-bit microcontroller (MCU) is a compact computer-on-a-chip built around an 8-bit data path. Within the broader semiconductor taxonomy, an MCU sits below microprocessor (MPU) and above application-specific integrated circuit (ASIC); the PIC16 family in particular is a mature mid-range RISC architecture from Microchip widely used for control loops, sensor interfacing, and human-machine interface (HMI) tasks. The PIC16F723 belongs to the "F72X" subset that adds nanoWatt XLP peripherals for ultra-low-power sleep modes.
Key features of the PIC16F723T-I/MV include an enhanced mid-range 16-bit instruction set with 49 instructions, 11-channel 8-bit ADC, two 8-bit and one 16-bit timers, EUSART, MSSP (SPI/I2C), and ultra-low-power sleep currents in the nanoamp range. The 28-pin UQFN package is the same 4x4 mm land pattern shared across the family, enabling footprint-compatible migration.
The device is built on Microchip's enhanced mid-range core running up to 20 MHz at 5V, with a wide 1.8V-5.5V supply that simplifies single-cell Li-ion or 3.3V system designs. XLP technology provides Sleep currents under 20 nA typical and an integrated low-power watchdog, allowing years of operation on coin-cell batteries.
Typical applications include battery-powered sensor nodes, consumer appliances, LED lighting controllers, remote controls, and low-end industrial control. The compact UQFN package suits space-constrained handheld products where board area is at a premium.
When designing with this part, derate the maximum clock at lower VDD (16 MHz at 2.5V, 8 MHz at 1.8V). Ensure MCLR is properly tied or configured as a digital input to avoid unintentional reset.
This page synthesizes distributor pricing, drop-in UQFN-28 alternatives from the PIC16F family, and practical design notes not found in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho PIC16F723T-I/MV — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC16F723T-I/MV (cùng hình factor và footprint) — khác nhau ở ADC, I/O Pins, Package, Program Memory (Flash), Timers.
PIC16F723A-I/MV
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16F722T-I/MV
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16F726-I/MV
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC16F722A-I/MV
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC16F1847-I/MV
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC16F723T-I/MV Tỷ lệ tối đa & tính chất điện
| Core Architecture | 8-bit PIC enhanced mid-range |
| Program Memory (Flash) | 7 KB |
| Data RAM | 192 bytes |
| Data EEPROM | 0 bytes (not present on this family variant per datasheet) |
| Maximum CPU Speed | 20 MHz |
| Supply Voltage (VDD) | 1.8 V to 5.5 V |
| Nhiệt độ hoạt động | -40 C to +85 C (Industrial) |
| I/O Pins | 25 (typical for 28-pin package) |
| ADC | 11-channel, 8-bit |
| Timers | 2 x 8-bit, 1 x 16-bit |
| Communication | EUSART, MSSP (SPI / I2C) |
| Low-Power Technology | nanoWatt XLP |
| Hộp | UQFN-28 (MV) 4x4 mm |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC16F723T-I/MV
| Chân 1 | RA0/AN0 — Bidirectional I/O / ADC input channel 0 |
| Chân 2 | RA1/AN1 — Bidirectional I/O / ADC input channel 1 |
| Chân 3 | RA2/AN2 — Bidirectional I/O / ADC input channel 2 |
| Chân 4 | RA3/AN3/VREF+ — Bidirectional I/O / ADC input / voltage reference |
| Chân 5 | RA4/AN4/T0CKI — Bidirectional I/O / ADC input / Timer0 clock |
| Chân 6 | RA5/AN5/SS/HLVDIN — Bidirectional I/O / ADC / SPI slave select / HLVD |
| Chân 7 | RA6/OSC2/CLKOUT — I/O / oscillator output / clock output |
| Chân 8 | RA7/OSC1/CLKIN — I/O / oscillator input / external clock |
| Chân 9 | VSS — Ground reference |
| Chân 10 | VDD — Positive supply voltage |
| Chân 11 | RB0/AN12/INT — I/O / ADC / external interrupt |
| Chân 12 | RB1/AN10 — I/O / ADC |
| Chân 13 | RB2/AN8 — I/O / ADC |
| Chân 14 | RB3/AN9/PGM — I/O / ADC / low-voltage programming |
| Chân 15 | RB4/AN11 — I/O / ADC |
| Chân 16 | RB5/AN13 — I/O / ADC |
| Chân 17 | RB6/PGC — I/O / ICSP clock |
| Chân 18 | RB7/PGD — I/O / ICSP data |
| Chân 19 | VSS — Ground reference |
| Chân 20 | VDD — Positive supply voltage |
| Chân 21 | RC0/SOSCO — I/O / secondary oscillator output |
| Chân 22 | RC1/SOSCI — I/O / secondary oscillator input |
| Chân 23 | RC2/CCP1 — I/O / capture/compare/PWM |
| Chân 24 | RC3/SCK/SCL — I/O / SPI clock / I2C clock |
| Chân 25 | RC4/SDI/SDA — I/O / SPI data in / I2C data |
| Chân 26 | RC5/SDO — I/O / SPI data out |
| Chân 27 | RC6/TX/CK — I/O / EUSART TX / clock |
| Chân 28 | RC7/RX/DT — I/O / EUSART RX / data |
| Chân 29 | EP (Exposed Pad) — Must be soldered to ground plane for thermal/electrical performance |
Ứng dụng tiêu biểu
PIC16F723T-I/MV phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Nodes, Consumer Appliance Control, LED Lighting Controllers, Remote Controls and HMI, Industrial Control and Monitoring, Low-End Medical and Wellness Devices.
Battery-Powered Sensor Nodes
The PIC16F723T-I/MV suits wireless sensor nodes where nanoWatt XLP sleep currents under 20 nA typical extend coin-cell battery life to years. Its 1.8 V to 5.5 V supply supports single-cell Li-ion or 2x AA chemistries without boost converters, and the 11-channel 8-bit ADC handles multiple temperature, light, or humidity sensors in environmental monitors. The 7 KB Flash accommodates small RTOS-free control loops with state machines, and the 20 MHz core processes sensor filtering in real time. Pair with a 2.4 GHz transceiver module for complete IoT nodes; the low active current keeps total system consumption minimal.
Được đề xuất
Consumer Appliance Control
The PIC16F723T-I/MV is well matched to consumer appliances such as coffee makers, microwave ovens, washing machines, and air purifiers, where the 25 I/O pins drive relays, keypads, seven-segment displays, and triac interfaces. The 8-bit core executes PID-like control loops at 20 MHz with predictable latency, and the EUSART plus MSSP (SPI/I2C) interface to sensors, Wi-Fi modules, and LED drivers. Industrial temperature grade (-40 to +85 C) handles under-cabinet appliance environments. The UQFN-28 package fits compact PCBs behind displays or inside small enclosures.
Được đề xuất
LED Lighting Controllers
The PIC16F723T-I/MV drives multi-channel LED strings in architectural and decorative lighting via hardware PWM or firmware bit-banging, while the 11-channel ADC reads ambient light sensors for closed-loop dimming. NanoWatt XLP technology enables always-on occupancy sensors that wake the MCU only when motion is detected, preserving the EUP standby directives. The wide 1.8 V to 5.5 V supply simplifies designs that run from a 3.3 V regulated rail or directly from rectified mains via capacitive dropper. The 7 KB Flash holds color-mixing tables and DMX-512 style protocols for commercial fixtures.
Được đề xuất
Remote Controls and HMI
Infrared and RF remote controls benefit from the PIC16F723T-I/MV's XLP sleep mode, which allows multi-year operation on a coin cell while supporting wake-on-keypad interrupts. The MSSP peripheral drives SPI/I2C OLED displays for status feedback, and the EUSART interfaces with sub-GHz RF modules such as the Microchip MRF89XA. The 25 I/O pins scan keypads up to 5x5 matrix without additional logic. The compact UQFN-28 4x4 mm package fits inside handheld enclosures where every square millimeter matters.
Được đề xuất
Industrial Control and Monitoring
Industrial sensor hubs and small PLCs leverage the PIC16F723T-I/MV's 11-channel ADC for monitoring pressure, flow, and level transducers across 4-20 mA loops with external signal conditioning. The wide supply range survives 24 V industrial bus voltage drops after regulator stages, and the -40 to +85 C industrial temperature grade meets IEC 60068-2 environmental requirements for control cabinets. The 8-bit core executes Modbus RTU framing on the EUSART for SCADA integration, while the small UQFN package supports dense I/O boards with multiple MCUs networked together.
Được đề xuất
Low-End Medical and Wellness Devices
The PIC16F723T-I/MV powers personal wellness devices such as digital thermometers, pulse oximeters, and medication reminders, where the nanoWatt XLP technology extends battery life and the 11-channel ADC reads multiple biometric sensors. The 1.8 V minimum supply supports single-cell alkaline or coin-cell operation directly, simplifying BOM cost. The IEC 60730 Class B-ready diagnostics features in the PIC16F72X family support household medical devices, though FDA-cleared designs should select the PIC16F188xx family with formal IEC 60730 library support rather than this general-purpose F72X part.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC16F723T-I/MV — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC16F723A-I/MV | PIC16F722T-I/MV | PIC16F726-I/MV | PIC16F1847-I/MV |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | UQFN-28 (MV) 4x4 mm | UQFN-28 (MV) 4x4 mm - same | UQFN-28 (MV) 4x4 mm - same | UQFN-28 (MV) 4x4 mm - same | UQFN-28 (MV) 4x4 mm - same |
| Flash Program Memory | 7 KB | 7 KB | 3.5 KB (-50%) | 14 KB (+100%) | 14 KB (+100%) |
| RAM | 192 bytes | 192 bytes | 192 bytes | 368 bytes (+92%) | 1024 bytes (+433%) |
| Maximum CPU Speed | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 32 MHz (+60%) |
| Supply Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| ADC | 11-channel 8-bit | 11-channel 8-bit | 11-channel 8-bit | 11-channel 8-bit | 12-channel 10-bit (improved) |
| Low-Power Technology | nanoWatt XLP | nanoWatt XLP | nanoWatt XLP | nanoWatt XLP | nanoWatt XLP |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) |
| Approx. Unit Price (Qty 1000) | 1.05 USD | Similar ~1.05 USD | ~0.95 USD (-10%) | ~1.25 USD (+19%) | ~1.65 USD (+57%) |
Bảo phân biệt quan trọng
- Recommended upgrade part with minor silicon revision (vsPIC16F723A-I/MV)
- Higher memory headroom in same footprint (vsPIC16F726-I/MV)
- Cost-optimized for memory-light applications (vsPIC16F722T-I/MV)
- Highest feature density alternative in UQFN-28 (vsPIC16F1847-I/MV)
Ghi chú thiết kế
Estimated: at 20 MHz active and 3.3 V VDD, the PIC16F723 draws approximately 2.5 mA (active current per datasheet electrical characteristics). In Sleep with WDT disabled, XLP sleep current is typically under 20 nA, enabling multi-year battery life on a 220 mAh coin cell. Place a 100 nF decoupling capacitor within 5 mm of each VDD pin and a 10 uF bulk capacitor near the IC. For battery applications, add a low-Iq LDO such as Microchip MCP1700 to provide clean 3.3 V from a discharging Li-ion source.
The UQFN-28 (MV) package has a center exposed thermal pad on pin 29 that must be soldered to a ground plane for thermal dissipation and electrical performance. Use a 4x4 array of 0.3 mm thermal vias under the pad to stitch to the inner ground layer. Keep traces short and direct to minimize EMI on high-speed signals; for crystal traces (RA6/RA7), surround them with a ground guard ring and keep total length under 10 mm to avoid oscillator startup issues.
Do not leave MCLR floating - tie it to VDD through a 10 kohm resistor or drive it with the ICSP programmer's reset line. Avoid exceeding the maximum ICSP clock frequency during in-circuit programming; the PIC16F72X family supports up to 4 MHz ICSP clock. When using the ADC, allow adequate acquisition time by setting the TACQ register appropriately for source impedance - approximately 4 us for 10 kohm sources. Do not program the configuration bits to disable the watchdog without an explicit fallback reset strategy in firmware.
Route the ICSP signals (PGC on RB6, PGD on RB7) so that a programming header can be accessed without removing the device from the board. Avoid placing the programming header behind tall components. Keep analog and digital ground domains separated where possible, joining them at a single point near the IC's VSS pin. The MSSP peripheral shares RB4/RB3/SDA/SCL pins; ensure I2C pull-ups are sized appropriately (typically 4.7 kohm at 100 kHz, 2.2 kohm at 400 kHz).
Thông tin tuân thủ
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified - choose PIC16F193x or PIC16F188xx automotive-grade variants for vehicle applications. Halogen-free status not explicitly stated in the verified data.
