PIC18C452T-I/PT - 8-Bit 40MHz 32KB OTP MCU 44-TQFP | Microchip
MPN: PIC18C452T-I/PT ✗ Cuối đờiPIC18C452T-I/PT Tóm tắt
A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, data memory, and programmable I/O peripherals. The PIC18C family extends the legacy PIC16 architecture with a 16-bit wide instruction word, 77 single-word instructions, a hardware multiplier, and an extended 16-level stack, positioning the part as an upgrade path for PIC16C5X, PIC12CXXX, PIC16CXX, and PIC17CXX designs while maintaining source-code compatibility at the architectural level.
Key features include OTP program memory for fast prototyping and small-to-medium volume production, hardware USART for full-duplex asynchronous serial, Master Synchronous Serial Port (MSSP) supporting SPI and I2C, capture/compare/PWM (CCP) modules, a 10-bit ADC with up to 8 input channels, and a Parallel Slave Port for direct microprocessor bus attachment. The wide operating voltage range of 4.2 V to 5.5 V supports standard 5 V embedded designs.
Typical applications include industrial control and automation, sensor interface boards, motor control front-ends, instrumentation and data acquisition, consumer appliances with display/keypad interfaces, and embedded communication gateways requiring USART plus SPI/I2C peripherals. The PSP allows the MCU to behave as a memory-mapped peripheral to an external host processor.
Designers should plan OTP programming into the production flow (windowed JW package is required for code iteration), budget for the 1.5 KB RAM ceiling when selecting higher-protocol stacks, and use the ICD (In-Circuit Debug) variants PIC18C452-I/PT or PIC18F452-I/PT for development before committing to OTP volume. Pin-compatible Flash alternatives exist if field firmware update is required.
This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho PIC18C452T-I/PT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC18C452T-I/PT (cùng hình factor và footprint) — khác nhau ở Package, Timers, ADC, Operating Temperature, CCP Modules.
PIC18C452-I/PT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC18C452T-E/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F452-I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC18F46J50-I/PT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC18F452T-I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC18F4525-I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC18C452T-I/PT Tỷ lệ tối đa & tính chất điện
| Core | PIC18C 8-bit |
| Instruction Set Architecture | 16-bit wide, 77 single-word instructions |
| Maximum CPU Speed | 40 MHz (10 MIPS) |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 32 KB (16K x 16) |
| RAM Size | 1.5 KB (1536 bytes) |
| EEPROM | None (OTP device) |
| I/O Pins | 34 |
| ADC | 10-bit, up to 8 channels |
| Timers | 2 x 8-bit, 3 x 16-bit |
| CCP Modules | 2 (Capture/Compare/PWM) |
| Serial Interfaces | 1 x USART, 1 x MSSP (SPI / I2C) |
| Parallel Slave Port (PSP) | Yes |
| Operating Voltage | 4.2 V to 5.5 V |
| Nhiệt độ hoạt động | -40C to +85C (Industrial) |
| Hộp | 44-TQFP (10x10 mm) |
| Kiểu lắp đặt | Surface Mount |
| Cấp MSL | 3 |
| Lead-Free / RoHS | Lead-Free finish (check lot for full RoHS) |
| ICSP / ICD Support | Yes (In-Circuit Serial Programming) |
Cấu hình chân PIC18C452T-I/PT
| Chân 1 | MCLR/VPP/RA5 — Master Clear / Programming Voltage / Port A bit 5 |
| Chân 2 | RA0/AN0 — Port A bit 0 / Analog input 0 |
| Chân 3 | RA1/AN1 — Port A bit 1 / Analog input 1 |
| Chân 4 | RA2/AN2/VREF- — Port A bit 2 / Analog input 2 / ADC VREF- |
| Chân 5 | RA3/AN3/VREF+ — Port A bit 3 / Analog input 3 / ADC VREF+ |
| Chân 6 | RA4/TOCKI — Port A bit 4 / Timer 0 clock input |
| Chân 7 | RA5/SS/AN4 — Port A bit 5 / SPI Slave Select / Analog input 4 |
| Chân 8 | RE0/RD/AN5 — Port E bit 0 / Parallel Slave Port read / Analog input 5 |
| Chân 9 | RE1/WR/AN6 — Port E bit 1 / Parallel Slave Port write / Analog input 6 |
| Chân 10 | RE2/CS/AN7 — Port E bit 2 / Parallel Slave Port chip select / Analog input 7 |
| Chân 11 | VDD — Digital supply voltage (4.2V-5.5V) |
| Chân 12 | VSS — Digital ground |
| Chân 13 | OSC1/CLKIN — Oscillator crystal input / external clock in |
| Chân 14 | OSC2/CLKOUT — Oscillator crystal output / clock out |
| Chân 15 | RC0/T1OSO/T1CKI — Port C bit 0 / Timer 1 oscillator output / T1 clock in |
| Chân 16 | RC1/T1OSI/CCP2 — Port C bit 1 / Timer 1 oscillator input / CCP2 |
| Chân 17 | RC2/CCP1 — Port C bit 2 / CCP1 PWM output |
| Chân 18 | RC3/SCK/SCL — Port C bit 3 / SPI clock / I2C clock |
| Chân 19 | RD0/PSP0 — Port D bit 0 / Parallel Slave Port bit 0 |
| Chân 20 | RD1/PSP1 — Port D bit 1 / Parallel Slave Port bit 1 |
| Chân 21 | RD2/PSP2 — Port D bit 2 / Parallel Slave Port bit 2 |
| Chân 22 | RD3/PSP3 — Port D bit 3 / Parallel Slave Port bit 3 |
| Chân 23 | RC4/SDI/SDA — Port C bit 4 / SPI data in / I2C data |
| Chân 24 | RC5/SDO — Port C bit 5 / SPI data out |
| Chân 25 | RC6/TX/CK — Port C bit 6 / USART TX / USART clock |
| Chân 26 | RC7/RX/DT — Port C bit 7 / USART RX / USART data |
| Chân 27 | RD4/PSP4 — Port D bit 4 / Parallel Slave Port bit 4 |
| Chân 28 | RD5/PSP5 — Port D bit 5 / Parallel Slave Port bit 5 |
| Chân 29 | RD6/PSP6 — Port D bit 6 / Parallel Slave Port bit 6 |
| Chân 30 | RD7/PSP7 — Port D bit 7 / Parallel Slave Port bit 7 |
| Chân 31 | VSS — Digital ground |
| Chân 32 | VDD — Digital supply voltage (4.2V-5.5V) |
| Chân 33 | RB0/INT0 — Port B bit 0 / External interrupt 0 |
| Chân 34 | RB1/INT1 — Port B bit 1 / External interrupt 1 |
| Chân 35 | RB2/INT2 — Port B bit 2 / External interrupt 2 |
| Chân 36 | RB3/CCP2 — Port B bit 3 / CCP2 alternate |
| Chân 37 | RB4 — Port B bit 4 (interrupt-on-change) |
| Chân 38 | RB5 — Port B bit 5 (interrupt-on-change) |
| Chân 39 | RB6/PGC — Port B bit 6 / ICSP clock |
| Chân 40 | RB7/PGD — Port B bit 7 / ICSP data |
| Chân 41 | AVSS — Analog ground |
| Chân 42 | AVDD — Analog supply voltage |
| Chân 43 | NC — Not connected (per datasheet, no bond-out) |
| Chân 44 | NC — Not connected (per datasheet, no bond-out) |
Ứng dụng tiêu biểu
PIC18C452T-I/PT phù hợp cho 6 Áp dụngs: Industrial Control & Automation, Sensor Interface & Data Acquisition, Consumer Appliances with Display Interfaces, Embedded Communication Gateways, Motor Control Front-Ends, Instrumentation & Test Equipment.
Industrial Control & Automation
The PIC18C452T-I/PT is well-suited for industrial control and PLC-style I/O modules thanks to its 40 MHz core (10 MIPS), 34 digital I/O, and 4.2V to 5.5V 5V-native operation that interfaces directly to industrial sensors and 24V-tolerant optocouplers with simple resistor dividers. Its 32 KB OTP program memory stores deterministic control firmware, while the 10-bit ADC with up to 8 channels reads analog process variables (temperature, pressure, flow) at sufficient resolution for closed-loop PID. The USART plus MSSP (SPI/I2C) enables connection to HMI displays and remote I/O expansion modules. Compared with PIC18F452-I/PT, the OTP variant offers one-time-program security that prevents reverse engineering of proprietary control algorithms. For new industrial designs, however, the Flash-based PIC18F452-I/PT is preferred because field firmware updates are critical for deployed industrial assets.
Được đề xuất
Sensor Interface & Data Acquisition
For data acquisition front-ends, the PIC18C452T-I/PT provides 10-bit ADC resolution across 8 input channels, sample-and-hold, and a programmable acquisition timer adequate for low-bandwidth sensor arrays (temperature, strain gauge, light, gas). The 1.5 KB RAM supports small circular acquisition buffers, while the USART streams packets to a host computer. Combined with the MSSP in SPI mode, the MCU can read digital sensors (accelerometers, pressure ICs) on the same board. The OTP memory ensures measurement calibration routines cannot be tampered with after deployment, a regulatory benefit for medical or metering applications. Migration tip: pairing this part with a precision external ADC such as MCP3421 yields higher dynamic range when 12-bit or 16-bit accuracy is needed.
Được đề xuất
Consumer Appliances with Display Interfaces
Household appliances (washing machines, microwave ovens, HVAC thermostats) commonly use PIC18C452T-I/PT as the main controller driving character LCDs, keypads, and rotary encoders. The 34 I/O pins comfortably handle a 4x4 keypad matrix, an 8-character LCD parallel bus, and indicator LEDs with spare lines for relay drivers. The two CCP (Capture/Compare/PWM) channels generate PWM signals for motor speed control or TRIAC phase-angle firing. The 40 MHz CPU executes 10 MIPS, allowing real-time debouncing and PID temperature control. The OTP memory secures brand-specific firmware; the 5 V I/O tolerance directly drives standard character LCD modules without level shifters.
Được đề xuất
Embedded Communication Gateways
Protocol-conversion gateways (RS-232 to RS-485, SPI to UART bridges, MODBUS slaves) are a natural fit for PIC18C452T-I/PT. The USART implements RS-232/RS-485 with external transceivers, while the MSSP in I2C mode connects to EEPROM, RTC, or temperature sensors. The PSP (Parallel Slave Port) allows an external host processor to read the gateway's status registers as if it were memory, easing integration into larger systems. With 32 KB of code space, the MCU can host MODBUS RTU, DMX512, or simple custom protocols. For wireless gateway upgrades, designers can pair the MCU with MRF24J40 (ZigBee) or RN171 (WiFi) modules via SPI. The industrial temperature range ensures deployment in uncontrolled enclosures.
Được đề xuất
Motor Control Front-Ends
Low-power DC motor and stepper control benefit from PIC18C452T-I/PT's two CCP modules generating complementary PWM outputs, plus a third timer for commutation sequencing. The 10 MIPS throughput handles trapezoidal commutation profiles for small BLDC motors used in fans, pumps, or robotic actuators. The 10-bit ADC samples back-EMF or current-sense amplifiers at the PWM zero-crossing, closing the speed/torque loop. The 5 V I/O directly interfaces to IR2104 half-bridge gate drivers without level shifting. Designers who need field updates for tuning motor parameters should target PIC18F452-I/PT, which keeps the same PWM/timer architecture but adds Flash for in-application reprogramming.
Được đề xuất
Instrumentation & Test Equipment
Bench-top instrumentation (logic analyzers, signal generators, educational lab kits) historically used PIC18C452T-I/PT to manage front-panel keypads, character LCDs, and USB-to-UART bridges. The 32 KB OTP fits full protocol stacks for SCPI command parsing, while the USART streams captured data to a PC at 115.2 kbps. The MSSP in SPI mode drives DACs or digital potentiometers for waveform synthesis. For modern lab equipment requiring firmware updates as features are added, designers should plan migration to PIC18F452-I/PT or PIC18F46J50-I/PT, both of which are pin-compatible 44-TQFP Flash replacements. The PIC18C452T-I/PT remains useful when the firmware is locked and cost-sensitive educational equipment is being manufactured in volume.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC18C452T-I/PT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC18C452-I/PT | PIC18C452T-E/PT | PIC18F452-I/PT | PIC18F46J50-I/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-TQFP (10x10 mm) | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same | 44-TQFP (10x10 mm) - same |
| Program Memory Type | 32 KB OTP | 32 KB OTP | 32 KB OTP | 32 KB Flash | 64 KB Flash |
| CPU Speed | 40 MHz (10 MIPS) | 40 MHz (10 MIPS) | 40 MHz (10 MIPS) | 40 MHz (10 MIPS) | 48 MHz |
| RAM Size | 1.5 KB | 1.5 KB | 1.5 KB | 1.5 KB | 3.8 KB |
| Operating Voltage | 4.2 V - 5.5 V | 4.2 V - 5.5 V | 4.2 V - 5.5 V | 4.2 V - 5.5 V | 2.0 V - 3.6 V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +125C | -40C to +85C | -40C to +85C |
| ADC Channels / Resolution | 8 ch / 10-bit | 8 ch / 10-bit | 8 ch / 10-bit | 8 ch / 10-bit | 13 ch / 10-bit |
| Special Peripherals | PSP, MSSP (SPI/I2C), USART | PSP, MSSP, USART | PSP, MSSP, USART | PSP, MSSP, USART, ICD | USB 2.0 FS, PSP, MSSP, USART, ICD |
Bảo phân biệt quan trọng
- One-Time-Programmable memory provides firmware IP protection (vsPIC18F452-I/PT)
- Industrial temperature range with full 5 V native I/O (vsPIC18F46J50-I/PT)
- Drop-in migration to Flash with same pinout (vsExternal 8051-based MCUs)
Ghi chú thiết kế
PIC18C452T-I/PT is OTP (One-Time Programmable): code is written once and cannot be erased. Use the PIC18C452-I/PT (non-T) or PIC18F452-I/PT for development with ICD debugging, then program the OTP version for production. Plan ICSP programming jig time into your SMT line budget since OTP parts cannot be reworked in the field.
The MCU operates from 4.2 V to 5.5 V. Place a 100 nF ceramic decoupling capacitor within 5 mm of each VDD pin (pins 11 and 32) and a bulk 10 uF tantalum or aluminum cap on the supply rail. The analog AVDD pin (42) requires its own 100 nF + 10 uF filter with a ferrite bead to isolate ADC noise from digital switching.
Keep the 40 MHz crystal (or external oscillator) traces to pins 13-14 short and symmetric, with the load capacitors (typically 15-33 pF) placed within 3 mm of the OSC pins. Avoid routing signal traces under the crystal or its capacitors. For high-EMI environments, use a 4-layer PCB with a continuous ground plane beneath the TQFP to reduce radiated emissions.
The 10-bit ADC achieves its rated accuracy only when the source impedance is below 2.5 kohm. Add an op-amp buffer (MCP6001 or similar) for high-impedance sensors. Use the RA3/AN3 pin as the dedicated VREF+ input and decouple it with 100 nF + 10 uF; do not tie VREF+ directly to VDD if absolute ADC accuracy matters.
Thông tin tuân thủ
Lead-free (Pb-free) finish; RoHS compliance verified per Microchip product page. Industrial temperature grade only - not AEC-Q100 qualified (use PIC18C452T-E/PT for extended temp).