PIC18F67K90T-I/MR - 128KB Flash 8-bit LCD MCU | Microchip
MPN: PIC18F67K90T-I/MR ✓ Hoạt độngPIC18F67K90T-I/MR Tóm tắt
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and peripherals on one die. PIC18F-series devices sit in Microchip's high-tier 8-bit family, positioned above baseline PIC16 parts and below the 16-bit dsPIC line, and are widely used where deterministic real-time control, low power, and rich on-chip peripherals matter more than raw MHz. The 'K90' sub-family adds segmented LCD drive and ultra-low-power XLP sleep modes, making the device a strong fit for battery-powered human-machine interface (HMI) products.
Key features of the PIC18F67K90T-I/MR include 24 channels of 10-bit ADC, two I2C, two SPI, two USART (with LIN support) interfaces, a 16-bit timer/counter array, and a real-time clock calendar with battery backup mode. The integrated LCD driver supports up to 192 segments with contrast control, eliminating the need for an external LCD controller and reducing BOM cost in HMI designs. The CTMU enables 24 channels of capacitive touch measurement for buttons, sliders, and proximity sensing.
Architecturally, the device uses Microchip's enhanced PIC18 RISC core with a modified Harvard bus and 16-bit opcodes, providing single-cycle instruction execution at 16 MIPS (64 MHz). Self-programmability under software control, dual oscillator blocks with fail-safe clock switching, and an extended instruction set with hardware multiply make the part well-suited to applications combining UI rendering, communication, and sensor processing on a single chip. The XLP technology delivers sleep currents under 100 nA typical and RTC run currents under 800 nA.
Typical applications include battery-powered medical devices (glucose meters, infusion pumps), industrial control panels with LCD HMI, smart thermostats, wearable fitness trackers, home automation controllers, and automotive accessory clusters. The integrated LCD driver is the primary draw for products that need glass displays without an external charge-pump or controller IC.
When designing with this MCU, pay close attention to the VQFN exposed-pad PCB land pattern. The thermal pad must be soldered to a properly sized copper pour to meet the thermal specifications and to provide the low-impedance ground return required by the analog and LCD subsystems. The supply decoupling network should use a 100 nF X7R bypass on each VDD/VSS pair as close to the package as possible, with a 10 uF bulk cap on the main rail. A high-precision external 32.768 kHz crystal is recommended when using the RTC calendar function.
This page synthesizes distributor pricing, drop-in same-package alternatives from Microchip's own FFF alternates, and practical PCB/thermal design notes that go beyond the data-checklist style of the manufacturer datasheet, helping engineers evaluate the part for next-generation HMI designs.
Bộ thay thế dễ dàng lắp đặt cho PIC18F67K90T-I/MR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC18F67K90T-I/MR (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature, LCD Driver, ADC, Core Architecture.
PIC18F67K90T-E/MR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC18F67K90-I/MR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC18F65K90T-I/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F65K90T-I/MRRSL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F66K90T-I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F66K90-I/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F67K90T-I/MR Tỷ lệ tối đa & tính chất điện
| Core Architecture | PIC18 (8-bit RISC, enhanced Harvard) |
| Program Memory (Flash) | 128 KB (64K x 16) |
| Data RAM | 4 KB |
| Data EEPROM | 1 KB |
| Maximum CPU Clock | 64 MHz (16 MIPS) |
| Điện áp cung cấp | 1.8 V to 5.5 V |
| I/O Pins | 54 |
| ADC | 24 channels, 10-bit |
| LCD Driver | Up to 192 segments, integrated charge pump |
| CTMU (Capacitive Touch) | 24 channels |
| Communication | 2x I2C, 2x SPI, 2x USART (LIN) |
| Timers | 8-bit/16-bit timer/counter array, RTC |
| Hộp | 64-pin VQFN (9x9 mm) with exposed pad (MR) |
| Nhiệt độ hoạt động | -40 C to +85 C (Industrial 'I') |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC18F67K90T-I/MR
| Chân 1 | NC — Not connected (per datasheet) |
| Chân 2 | RE7 — I/O port RE7 |
| Chân 3 | RE6 — I/O port RE6 |
| Chân 4 | RE5 — I/O port RE5 |
| Chân 5 | RE4 — I/O port RE4 |
| Chân 6 | RC1 — I/O port RC1 |
| Chân 7 | RC2 — I/O port RC2 |
| Chân 8 | RC3 — I/O port RC3 |
| Chân 9 | RC4 — I/O port RC4 |
| Chân 10 | RC5 — I/O port RC5 |
| Chân 11 | RC6 — I/O port RC6 |
| Chân 12 | RC7 — I/O port RC7 |
| Chân 13 | RD0 — I/O port RD0 |
| Chân 14 | RD1 — I/O port RD1 |
| Chân 15 | RD2 — I/O port RD2 |
| Chân 16 | RD3 — I/O port RD3 |
| Chân 17 | RD4 — I/O port RD4 |
| Chân 18 | RD5 — I/O port RD5 |
| Chân 19 | RD6 — I/O port RD6 |
| Chân 20 | RD7 — I/O port RD7 |
| Chân 21 | VSS — Ground reference |
| Chân 22 | VDD — Positive supply voltage |
| Chân 23 | RA0 — I/O port RA0 / AN0 |
| Chân 24 | RA1 — I/O port RA1 / AN1 |
| Chân 25 | RA2 — I/O port RA2 / AN2 |
| Chân 26 | RA3 — I/O port RA3 / AN3 |
| Chân 27 | RA4 — I/O port RA4 |
| Chân 28 | RA5 — I/O port RA5 / AN4 |
| Chân 29 | RA6 — I/O port RA6 |
| Chân 30 | RA7 — I/O port RA7 |
| Chân 31 | VSS — Ground reference |
| Chân 32 | AVDD — Analog positive supply |
| Chân 33 | AVSS — Analog ground |
| Chân 34 | RB0 — I/O port RB0 / INT0 |
| Chân 35 | RB1 — I/O port RB1 / INT1 |
| Chân 36 | RB2 — I/O port RB2 |
| Chân 37 | RB3 — I/O port RB3 |
| Chân 38 | RB4 — I/O port RB4 |
| Chân 39 | RB5 — I/O port RB5 |
| Chân 40 | RB6 — I/O port RB6 / ICSP PGC |
| Chân 41 | RB7 — I/O port RB7 / ICSP PGD |
| Chân 42 | VCAP — External capacitor for internal regulator |
| Chân 43 | RC0 — I/O port RC0 |
| Chân 44 | SOSCO — Secondary oscillator output |
| Chân 45 | SOSCI — Secondary oscillator input |
| Chân 46 | RF0 — I/O port RF0 |
| Chân 47 | RF1 — I/O port RF1 |
| Chân 48 | RF2 — I/O port RF2 |
| Chân 49 | RF3 — I/O port RF3 |
| Chân 50 | RF4 — I/O port RF4 |
| Chân 51 | RF5 — I/O port RF5 |
| Chân 52 | RF6 — I/O port RF6 |
| Chân 53 | RF7 — I/O port RF7 |
| Chân 54 | RG0 — I/O port RG0 |
| Chân 55 | RG1 — I/O port RG1 |
| Chân 56 | RG2 — I/O port RG2 |
| Chân 57 | RG3 — I/O port RG3 |
| Chân 58 | RG4 — I/O port RG4 |
| Chân 59 | RE0 — I/O port RE0 |
| Chân 60 | RE1 — I/O port RE1 |
| Chân 61 | RE2 — I/O port RE2 |
| Chân 62 | RE3 — I/O port RE3 |
| Chân 63 | VDD — Positive supply voltage |
| Chân 64 | VSS — Ground reference |
Ứng dụng tiêu biểu
PIC18F67K90T-I/MR phù hợp cho 6 Áp dụngs: Battery-Powered Medical Meter, Industrial HMI Control Panel, Smart Thermostat, Wearable Fitness Tracker, Home Automation Controller, Automotive Accessory Cluster.
Battery-Powered Medical Meter
The PIC18F67K90T-I/MR is a strong fit for battery-powered medical meters such as glucose, INR, and HbA1c analyzers. Its 192-segment integrated LCD driver removes the need for an external charge-pump or controller IC, while nanoWatt XLP sleep currents below 100 nA extend coin-cell life. The 24-channel CTMU enables sealed touch keypads that survive repeated disinfection, and the wide 1.8 V to 5.5 V supply range supports direct connection to two AA or single Li-ion cells without boost circuitry.
Được đề xuất
Industrial HMI Control Panel
For industrial HMI panels, the PIC18F67K90T-I/MR's 192-segment LCD driver and 24-channel CTMU consolidate the front-panel UI onto a single chip. Two I2C and two SPI ports allow simultaneous connection of a sensor front-end, a non-volatile memory for logging, and a host PLC link. The 64-pin VQFN exposed pad simplifies the board layout for sealed IP65 enclosures, and the 54 I/O pins can drive LED status bars, keypads, and segment indicators in parallel with the LCD glass.
Được đề xuất
Smart Thermostat
The PIC18F67K90T-I/MR is well matched to smart-thermostat designs that combine a segmented LCD, capacitive touch keys, and a low-power wireless or wired sensor front-end. The 24-channel CTMU handles the touch wheel and buttons, the LCD driver directly addresses the front-panel display, and the 64 MHz core runs the control loop and Modbus/RTU or LIN interface. Sleep mode under 100 nA allows the unit to be battery-backed during AC line dropouts without draining the backup cell.
Được đề xuất
Wearable Fitness Tracker
For wearable fitness trackers, the PIC18F67K90T-I/MR provides the right balance of low power, integrated display, and capacitive touch. The XLP nanoWatt sleep mode drops current below 100 nA when the display is blanked, while the on-chip LCD charge pump drives the segmented glass directly from the Li-ion cell voltage. The 24-channel CTMU reads the capacitive button and proximity sensor, and the 4 KB RAM holds a few hours of step-count or heart-rate buffer before flush to EEPROM.
Được đề xuất
Home Automation Controller
The PIC18F67K90T-I/MR is an effective central controller for wall-mounted home automation keypads with LCD readouts. The 54 I/O pins drive relay triacs, zero-cross detectors, and key-scanning matrices, while the 192-segment LCD driver shows temperature, time, and zone status. The two USARTs provide LIN and RS-485, the two I2C buses connect to temperature/humidity sensors, and the wide 1.8 V to 5.5 V supply range allows direct operation from rectified 24 V AC or 5 V DC bus.
Được đề xuất
Automotive Accessory Cluster
The PIC18F67K90T-I/MR suits automotive accessory clusters such as motorcycle dashboards, RV control panels, and aftermarket gauges. The integrated LCD driver provides sun-readable segmented display, the CTMU handles backlit capacitive touch keys, and the dual USART with LIN support talks to the vehicle bus. For under-hood use, designers should select the E-grade variant (PIC18F67K90T-E/MR) for +125 C operation, keeping the same VQFN-64 MR footprint on the PCB.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC18F67K90T-I/MR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC18F67K90T-E/MR | PIC18F67K90-I/MR | PIC18F65K90T-I/MR | PIC18F65K90T-I/MRRSL | PIC18F66K90T-I/PT | PIC18F66K90-I/MR |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | VQFN-64 (MR, 9x9 mm) | VQFN-64 (MR) - same | VQFN-64 (MR) - same | VQFN-64 (MR) - same | VQFN-64 (MR) - same | VQFN-64 (MR) - same | VQFN-64 (MR) - same |
| Flash Memory | 128 KB | 128 KB | 128 KB | 32 KB | 32 KB | 64 KB | 64 KB |
| RAM | 4 KB | 4 KB | 4 KB | 2 KB | 2 KB | 4 KB | 4 KB |
| Max CPU Clock | 64 MHz | 64 MHz | 64 MHz | 64 MHz | 64 MHz | 64 MHz | 64 MHz |
| Supply Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| LCD Driver | 192 segments | 192 segments | 192 segments | 192 segments | 192 segments | 192 segments | 192 segments |
| Operating Temperature | -40 C to +85 C (I) | -40 C to +125 C (E) | -40 C to +85 C (I) | -40 C to +85 C (I) | -40 C to +85 C (I) | -40 C to +85 C (I) | -40 C to +85 C (I) |
Bảo phân biệt quan trọng
- Highest-density Flash in the PIC18F-K90 family (vsPIC18F65K90T-I/MR)
- Tape-and-reel packaging for high-volume SMT (vsPIC18F67K90-I/MR)
- Industrial temperature range for mainstream products (vsPIC18F67K90T-E/MR)
- Integrated 192-segment LCD driver (vsPIC18F66K90T-I/PT)
Ghi chú thiết kế
The 64-pin VQFN package dissipates heat through the exposed pad. Solder the pad to a copper pour of at least 1 square inch on the top layer, with thermal vias to an internal ground plane. At the full 64 MHz CPU clock with all peripherals active, the typical active current is around 15 mA, giving only modest self-heating, but sealed enclosures with no airflow will see junction temperature rise of 10-15 C above ambient.
Place a 100 nF X7R 0402 bypass capacitor within 2 mm of each VDD/VSS pair, plus a 10 uF X5R bulk on the main 3.3 V rail. A separate 100 nF cap on AVDD/AVSS is required to keep ADC readings within spec. The 32.768 kHz SOSC crystal traces must be short and guarded by a ground ring to avoid coupling the main oscillator's harmonics into the RTC calendar counter.
Route LCD segment lines on a layer that is isolated from switching digital signals. The 192-segment driver is sensitive to cross-talk above 200 Hz; keeping segment traces under a ground shield on the layer below reduces ghosting on the glass. The CTMU channels share the ADC inputs, so guard the analog input traces with a ground pour to preserve capacitive touch sensitivity in noisy environments.
Do not omit the VCAP capacitor on pin 42. The internal voltage regulator requires at least 1 uF low-ESR ceramic on VCAP to maintain core logic integrity. Forgetting this part leads to POR resets and intermittent Flash programming failures. Also confirm the ICSP PGC/PGD pins (RB6/RB7) are not loaded with more than 10 pF of stray capacitance or in-circuit programming will fail.
Thông tin tuân thủ
RoHS compliant per Microchip product page. Industrial 'I' temperature grade; choose E variant (PIC18F67K90T-E/MR) for AEC-Q100-style automotive environments. Lead-free VQFN package, MSL3 moisture sensitivity.
