PIC24FJ128GB110-I/PF - 16-bit 32MHz USB OTG MCU 128KB Flash | Microchip
MPN: PIC24FJ128GB110-I/PF ✓ Hoạt độngPIC24FJ128GB110-I/PF Tóm tắt
A 16-bit microcontroller (MCU) is a programmable processor that uses a 16-bit data path and instruction word, sitting in the hierarchy between 8-bit MCUs (typical in simple embedded control) and 32-bit MCUs (typical in application processors). Microchip's PIC24F family is built on a modified Harvard RISC architecture and is widely used for low-power connected embedded designs because of its eXtreme Low Power (XLP) technology, which achieves standby currents under 100 nA in the GB2 family.
Key differentiating features include the integrated USB OTG transceiver (eliminates an external PHY), a parallel master port (PMP) for graphics or external memory, three I2C, three SPI, four UART channels, 23 independent timers, a 16-channel 10-bit ADC, and a CTMU peripheral for capacitive touch. The crypto engine accelerates AES, DES, and triple-DES, while the on-chip RNG supports secure key generation.
This architecture matters for designers building battery-powered peripherals because the same die that runs the user application can host USB device/host/OTG stacks, sensor fusion, and crypto without external components. The combination of 16KB RAM and 128KB Flash is well matched to mid-tier USB stacks plus custom application code.
Typical applications include USB HID peripherals, USB-to-UART bridges, secure token readers, low-power sensor hubs, industrial data loggers, and consumer medical devices that require isolated USB connectivity.
When designing with this part, mind the 100-pin TQFP land pattern and ensure the USB DP/DM traces are routed as a 90 ohm differential pair with a clean ground reference; the on-chip PHY is not tolerant of impedance discontinuities.
This page synthesizes distributor pricing tiers, drop-in same-package alternatives, and practical USB layout notes that go beyond the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho PIC24FJ128GB110-I/PF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC24FJ128GB110-I/PF (cùng hình factor và footprint) — khác nhau ở Package, ADC, Operating Temperature, Timers, Program Memory (Flash).
PIC24FJ256GB110-I/PF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24FJ192GB110-I/PF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC24FJ128GA110-I/PF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC24FJ128GB110-I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24FJ128GA010-I/PF
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24FJ128GB106-I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC24FJ128GB110-I/PF Tỷ lệ tối đa & tính chất điện
| Core | PIC24F (16-bit modified Harvard RISC) |
| Program Memory (Flash) | 128 KB (43K x 24 words) |
| Data Memory (RAM) | 16 KB |
| Maximum CPU Speed | 32 MHz (16 MIPS) |
| Operating Voltage | 2.0 V to 3.6 V |
| USB | USB 2.0 Full-Speed OTG with on-chip transceiver |
| I/O Pins | 83 |
| Timers | 23 independent |
| UART | 4 |
| SPI | 3 |
| I2C | 3 |
| ADC | 10-bit, 16-channel |
| Parallel Master Port (PMP) | Yes |
| Crypto Engine | AES, DES, 3-DES hardware accelerator |
| Random Number Generator | On-chip true RNG |
| Nhiệt độ hoạt động | -40 C to +85 C (industrial, -I suffix) |
| Hộp | 100-pin TQFP (14x14 mm), -PF suffix |
| Kiểu lắp đặt | Surface Mount |
| Cấp MSL | 3 (168 hours) |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC24FJ128GB110-I/PF
| Chân 1 | RP15/CN15/PMD15 — Remappable I/O / PMP data |
| Chân 2 | RP14/CN14/PMD14 — Remappable I/O / PMP data |
| Chân 3 | RP13/CN13/PMD13 — Remappable I/O / PMP data |
| Chân 4 | RP12/CN12/PMD12 — Remappable I/O / PMP data |
| Chân 5 | RP11/CN11/PMD11 — Remappable I/O / PMP data |
| Chân 6 | RP10/CN10/PMD10 — Remappable I/O / PMP data |
| Chân 7 | RP9/CN9/PMD9 — Remappable I/O / PMP data |
| Chân 8 | RP8/CN8/PMD8 — Remappable I/O / PMP data |
| Chân 9 | RP7/CN7/PMD7 — Remappable I/O / PMP data |
| Chân 10 | RP6/CN6/PMD6 — Remappable I/O / PMP data |
| Chân 11 | RP5/CN5/PMD5 — Remappable I/O / PMP data |
| Chân 12 | RP4/CN4/PMD4 — Remappable I/O / PMP data |
| Chân 13 | RP3/CN3/PMD3 — Remappable I/O / PMP data |
| Chân 14 | RP2/CN2/PMD2 — Remappable I/O / PMP data |
| Chân 15 | RP1/CN1/PMD1 — Remappable I/O / PMP data |
| Chân 16 | RP0/CN0/PMD0 — Remappable I/O / PMP data |
| Chân 17 | AN23/C1INC — ADC analog input 23 / comparator |
| Chân 18 | AN22/C1IND — ADC analog input 22 / comparator |
| Chân 19 | VDD — Positive supply (2.0-3.6 V) |
| Chân 20 | VSS — Ground reference |
| Chân 21 | AN21/C1INC — ADC analog input 21 / comparator |
| Chân 22 | AN20/C1IND — ADC analog input 20 / comparator |
| Chân 23 | AN19/C1OUT — ADC analog input 19 / comparator output |
| Chân 24 | AN18/C2OUT — ADC analog input 18 / comparator 2 output |
| Chân 25 | AN17/C2INC — ADC analog input 17 / comparator 2 |
| Chân 26 | AN16/C2IND — ADC analog input 16 / comparator 2 |
| Chân 27 | AN15 — ADC analog input 15 |
| Chân 28 | AN14 — ADC analog input 14 |
| Chân 29 | AVDD — Analog positive supply |
| Chân 30 | AVSS — Analog ground |
| Chân 31 | AN13 — ADC analog input 13 |
| Chân 32 | AN12 — ADC analog input 12 |
| Chân 33 | AN11 — ADC analog input 11 |
| Chân 34 | AN10 — ADC analog input 10 |
| Chân 35 | AN9 — ADC analog input 9 |
| Chân 36 | D- — USB OTG data minus (USB DP/DM) |
| Chân 37 | D+ — USB OTG data plus (USB DP/DM) |
| Chân 38 | VBUS — USB bus voltage monitor |
| Chân 39 | VUSB — USB transceiver supply (3.0-3.6 V) |
| Chân 40 | RBIAS — USB bias resistor reference |
| Chân 41 | RCV — USB receive (USB transceiver) |
| Chân 42 | ENVREG — Internal voltage regulator enable for USB |
| Chân 43 | VDD — Positive supply (2.0-3.6 V) |
| Chân 44 | VSS — Ground reference |
| Chân 45 | OSC1/CLKI — Crystal oscillator input or external clock |
| Chân 46 | OSC2/CLKO — Crystal oscillator output |
| Chân 47 | SOSCI/CN1/RC0 — Secondary oscillator / GPIO |
| Chân 48 | SOSCO/CN0/RC1 — Secondary oscillator / GPIO |
| Chân 49 | PGEC2/AN1/RP16 — ICSP clock / ADC / remappable I/O |
| Chân 50 | PGED2/AN0/RP17 — ICSP data / ADC / remappable I/O |
| Chân 51 | PGEC1/RP18 — ICSP clock 1 / remappable I/O |
| Chân 52 | PGED1/RP19 — ICSP data 1 / remappable I/O |
| Chân 53 | MCLR — Master clear (reset, active low) |
| Chân 54 | RA15 — Port A bit 15 |
| Chân 55 | RA14 — Port A bit 14 |
| Chân 56 | RA13 — Port A bit 13 |
| Chân 57 | RA12 — Port A bit 12 |
| Chân 58 | RA11 — Port A bit 11 |
| Chân 59 | RA10 — Port A bit 10 |
| Chân 60 | RA9 — Port A bit 9 |
| Chân 61 | RA8 — Port A bit 8 |
| Chân 62 | RA7 — Port A bit 7 |
| Chân 63 | RA6 — Port A bit 6 |
| Chân 64 | RA5 — Port A bit 5 |
| Chân 65 | RA4 — Port A bit 4 |
| Chân 66 | RA3 — Port A bit 3 |
| Chân 67 | RA2 — Port A bit 2 |
| Chân 68 | RA1 — Port A bit 1 |
| Chân 69 | RA0 — Port A bit 0 |
| Chân 70 | VDD — Positive supply (2.0-3.6 V) |
| Chân 71 | VSS — Ground reference |
| Chân 72 | PMCS1/RP20/CN20 — PMP chip select 1 / remappable I/O |
| Chân 73 | PMCS2/RP21/CN21 — PMP chip select 2 / remappable I/O |
| Chân 74 | PMA0/RP22/CN22 — PMP address / remappable I/O |
| Chân 75 | PMA1/RP23/CN23 — PMP address / remappable I/O |
| Chân 76 | PMA2/RP24/CN24 — PMP address / remappable I/O |
| Chân 77 | PMA3/RP25/CN25 — PMP address / remappable I/O |
| Chân 78 | PMA4/RP26/CN26 — PMP address / remappable I/O |
| Chân 79 | PMA5/RP27/CN27 — PMP address / remappable I/O |
| Chân 80 | PMA6/RP28/CN28 — PMP address / remappable I/O |
| Chân 81 | PMA7/RP29/CN29 — PMP address / remappable I/O |
| Chân 82 | PMRD/RP30/CN30 — PMP read strobe / remappable I/O |
| Chân 83 | PMWR/RP31/CN31 — PMP write strobe / remappable I/O |
| Chân 84 | PMBE/RP20 — PMP byte enable |
| Chân 85 | PMACK/RP21 — PMP acknowledge |
| Chân 86 | RP26/AN6 — Remappable I/O / ADC input 6 |
| Chân 87 | RP27/AN7 — Remappable I/O / ADC input 7 |
| Chân 88 | RP28/AN8 — Remappable I/O / ADC input 8 |
| Chân 89 | VDD — Positive supply (2.0-3.6 V) |
| Chân 90 | VSS — Ground reference |
| Chân 91 | INT0/RP32 — External interrupt 0 / remappable I/O |
| Chân 92 | INT1/RP33 — External interrupt 1 / remappable I/O |
| Chân 93 | INT2/RP34 — External interrupt 2 / remappable I/O |
| Chân 94 | RTCC/RP35 — RTCC output / remappable I/O |
| Chân 95 | RP36 — Remappable I/O |
| Chân 96 | RP37 — Remappable I/O |
| Chân 97 | RP38 — Remappable I/O |
| Chân 98 | RP39 — Remappable I/O |
| Chân 99 | RP40 — Remappable I/O |
| Chân 100 | RP41 — Remappable I/O |
Ứng dụng tiêu biểu
PIC24FJ128GB110-I/PF phù hợp cho 6 Áp dụngs: USB HID Peripherals, USB-to-UART Bridge, Secure Token / Authentication Reader, Low-Power Sensor Hub, Industrial Data Logger, Consumer Medical Device.
USB HID Peripherals
The PIC24FJ128GB110-I/PF is a strong fit for USB Human Interface Devices such as custom keyboards, pointing devices, and gaming controllers because the on-chip USB OTG transceiver eliminates the external PHY and the 16 MIPS performance easily runs the USB HID class driver plus application logic. Designers route DP/DM as a 90 ohm differential pair with the device running at 3.3 V nominal, and the 16 KB RAM provides headroom for HID report buffers. The integrated hardware crypto engine is also useful for authenticated HID devices such as secure input tokens.
Được đề xuất
USB-to-UART Bridge
With four on-chip UARTs plus a full-speed USB OTG port, the PIC24FJ128GB110-I/PF can act as a multi-channel USB-to-UART bridge for industrial gateways and embedded debug tools. The 128 KB Flash comfortably fits the CDC class driver and custom protocol shims, while the 23 timers cover baud-rate generation for all four UARTs. Running from a single 3.3 V rail and drawing microamps in Sleep makes it attractive for always-on bridge devices that stay plugged in but mostly idle.
Được đề xuất
Secure Token / Authentication Reader
For secure tokens and authentication readers, the PIC24FJ128GB110-I/PF combines an on-chip AES/DES/3-DES crypto accelerator and a true random number generator, removing the need for an external secure element on simple devices. The USB OTG peripheral allows the token to enumerate as a CCID or vendor-class reader, and the 16 MIPS core is sufficient to run authentication stacks. Industrial temperature range (-40C to +85C) suits outdoor payment and access-control terminals.
Được đề xuất
Low-Power Sensor Hub
The PIC24FJ128GB110-I/PF belongs to Microchip's eXtreme Low Power (XLP) family, achieving sub-100 nA standby currents, which makes it well suited to battery-powered sensor hubs that wake periodically to gather data and occasionally connect over USB for firmware updates. The 16-channel 10-bit ADC plus CTMU peripheral handles direct temperature, voltage, and capacitive-touch sensing. The 128 KB Flash holds USB stacks and sensor-fusion libraries without external memory.
Được đề xuất
Industrial Data Logger
Industrial data loggers benefit from the PIC24FJ128GB110-I/PF's 83 GPIO, three I2C, three SPI, four UART, and PMP peripherals for parallel memory or LCD interfaces. The 128 KB Flash plus 16 KB RAM supports file-system buffering to external SPI flash, while USB OTG enables removable storage enumeration as an MSD device. Industrial -40C to +85C rating ensures operation in unheated enclosures, and the wide 2.0-3.6 V VDD tolerates noisy 24 V-rail-derived supplies with proper regulation.
Được đề xuất
Consumer Medical Device
The PIC24FJ128GB110-I/PF suits compact consumer medical peripherals (glucose meters, pulse oximeters, connected thermometers) that require isolated USB connectivity for data upload without sacrificing battery life. The XLP sleep currents below 100 nA extend battery life across weeks of standby, the 16 MIPS core runs USB stacks and sensor processing concurrently, and the on-chip crypto engine protects health data with AES. The 100-pin TQFP gives ample I/O for displays, buttons, and battery monitoring.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC24FJ128GB110-I/PF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC24FJ256GB110-I/PF | PIC24FJ192GB110-I/PF | PIC24FJ128GA110-I/PF | PIC24FJ128GB110-I/PT | PIC24FJ128GA010-I/PF | PIC24FJ128GB106-I/PT |
|---|---|---|---|---|---|---|---|
| Package | TQFP-100 (14x14 mm) | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same | TQFP-100 (14x14 mm) - same | TQFP-100 (12x12 mm) - same pin count, smaller body | TQFP-100 (14x14 mm) - same | TQFP-64 - smaller |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 128 KB | 256 KB | 192 KB | 128 KB | 128 KB | 128 KB | 128 KB |
| RAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| USB OTG | Yes (integrated PHY) | Yes (integrated PHY) | Yes (integrated PHY) | No | Yes (integrated PHY) | No | Yes (integrated PHY) |
| Crypto Engine | AES/DES/3-DES + RNG | AES/DES/3-DES + RNG | AES/DES/3-DES + RNG | No | AES/DES/3-DES + RNG | No | AES/DES/3-DES + RNG |
| Maximum CPU Speed | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) | 32 MHz (16 MIPS) |
| Operating Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| GPIO Count | 83 | 83 | 83 | 83 | 83 | 83 | 52 (TQFP-64) |
| Temperature Range | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) |
Bảo phân biệt quan trọng
- Integrated USB OTG transceiver eliminates external PHY (vsPIC24FJ128GA010-I/PF)
- On-chip hardware AES/DES/3-DES crypto engine (vsPIC24FJ128GA110-I/PF)
- Drop-in upgrade path with same 100-pin TQFP footprint (vsPIC24FJ128GA010-I/PF)
- Higher Flash option on identical footprint (vsPIC24FJ256GB110-I/PF)
Ghi chú thiết kế
Route the USB D+ (pin 37) and D- (pin 36) signals as a 90 ohm differential pair on the top layer with a continuous ground reference plane underneath; keep total length under 50 mm where possible, and place the 15 kV-rated ESD protection array as close to the USB connector as the layout allows. The on-chip PHY is not tolerant of stubs or impedance discontinuities, so avoid via farms in the DP/DM path. Tie RBIAS (pin 40) to ground through a 12.3 kohm 1% resistor per the Microchip errata.
Provide separate bulk decoupling for VDD (1 uF ceramic plus 100 nF high-frequency bypass) and VUSB (4.7 uF plus 100 nF) within 5 mm of their respective pins, and place a ferrite bead between the main 3.3 V rail and VUSB when USB bus-powered designs exceed 100 mA. Keep AVDD/AVSS isolated from digital VDD/VSS with a ferrite or pi filter when the on-chip ADC is in use at more than 200 ksps to suppress digital switching noise.
Configure the ENVREG pin (pin 42) correctly: tie to VDD to use the internal 3.3 V USB regulator, or to VSS to disable it and supply VUSB externally. Driving ENVREG with the wrong polarity prevents USB enumeration and can over-stress the on-chip regulator. Also ensure the SOSC crystal (pins 47/48) load capacitors match the crystal's rated load capacitance, or the RTCC will drift and the USB bus timing on VBUS-detect may misbehave.
Estimated: at maximum CPU activity (32 MHz core, USB OTG active, all peripherals clocked) the PIC24FJ128GB110-I/PF draws approximately 35-40 mA on VDD, dissipating about 130 mW on the 100-pin TQFP land pattern. With the 14x14 mm package's theta_JA around 50 C/W on a 4-layer 1 oz PCB, junction-to-ambient rise is roughly 6.5 C - well within the 125 C maximum. No heatsink required.
Thông tin tuân thủ
RoHS and REACH compliance per Microchip product page; industrial -I temperature range is qualified but AEC-Q100 automotive qualification is not stated for this part - the -IPF suffix indicates industrial-only grade.
