PIC32MX230F128H-50I/PT - 50MHz 32-bit MCU, 128KB Flash | Microchip
MPN: PIC32MX230F128H-50I/PT ✓ Hoạt độngPIC32MX230F128H-50I/PT Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, communication interfaces, and analog blocks. In the embedded-system hierarchy, the PIC32MX230 family sits between 8-bit PIC MCUs and 32-bit Cortex-M parts, targeting cost-sensitive 32-bit applications that benefit from MIPS instruction-set familiarity, deterministic interrupt latency, and Microchip's MPLAB Harmony software ecosystem.
Key features include four SPI modules and two I2S interfaces for codec and serial audio, Peripheral Pin Select (PPS) for flexible peripheral-to-pin routing, a Parallel Master Port (PMP) with dual read/write buffers for graphics and external memory, a 10-bit 1 Msps ADC with up to 28 analog inputs, USB 2.0 full-speed device/host/OTG, and a CAN 2.0B module. The 50 MHz core delivers 83 DMIPS, and the wide peripheral mix supports both HMI and connectivity designs from a single part.
Typical applications include consumer audio with I2S codec front-ends, USB peripherals such as HID and CDC class devices, low-cost graphics terminals using PMP to drive LCD controllers, CAN nodes in industrial automation, and general-purpose 32-bit embedded control. The 16 KB SRAM and 128 KB Flash budget fits medium-sized state machines, USB stacks, and graphical user interfaces with character or small bitmap displays.
When designing with this part, follow Microchip's reference decoupling scheme (0.1 uF plus bulk), respect the 3.6 V absolute maximum on VDD, and use PPS to remap peripherals after layout changes. The 50 MHz core requires careful trace length matching for high-speed interfaces such as USB and PMP.
Bộ thay thế dễ dàng lắp đặt cho PIC32MX230F128H-50I/PT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC32MX230F128H-50I/PT (cùng hình factor và footprint) — khác nhau ở ADC, Package, USB, Parallel Master Port (PMP), UART Modules.
PIC32MX230F128HT-50I/PT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX230F128H-I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX230F128H-V/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC32MX130F128H-50I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX170F512H-50I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX230F128H-50I/PT Tỷ lệ tối đa & tính chất điện
| Core Architecture | MIPS32 M4K |
| Maximum Core Frequency | 50 MHz |
| Core Performance | 83 DMIPS |
| Program Flash Memory | 128 KB (128K x 8) |
| Data SRAM | 16 KB |
| Supply Voltage (VDD) | 2.3 V to 3.6 V |
| Nhiệt độ hoạt động | -40 C to +85 C (Industrial) |
| I/O Pins | 49 |
| Hộp | 64-pin TQFP (10x10 mm) |
| Kiểu lắp đặt | Surface Mount |
| ADC | 10-bit, 1 Msps, up to 28 channels |
| USB | USB 2.0 Full-Speed Device/Host/OTG |
| CAN | CAN 2.0B |
| SPI Modules | 4 |
| I2S Modules | 2 |
| UART Modules | 2 |
| I2C Modules | 2 |
| Parallel Master Port (PMP) | Yes, dual read/write buffers |
| Peripheral Pin Select (PPS) | Yes |
| Timers | 5 x 16-bit, 2 x 32-bit |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC32MX230F128H-50I/PT
| Chân 1 | RPB0/AN0 — Remappable I/O / Analog input 0 |
| Chân 2 | RPB1/AN1 — Remappable I/O / Analog input 1 |
| Chân 3 | RPB2/AN2 — Remappable I/O / Analog input 2 |
| Chân 4 | RPB3/AN3 — Remappable I/O / Analog input 3 |
| Chân 5 | RPB4/AN4 — Remappable I/O / Analog input 4 |
| Chân 6 | RPB5/AN5 — Remappable I/O / Analog input 5 |
| Chân 7 | RPB6/AN6 — Remappable I/O / Analog input 6 |
| Chân 8 | RPB7/AN7 — Remappable I/O / Analog input 7 |
| Chân 9 | RPB8/AN8 — Remappable I/O / Analog input 8 |
| Chân 10 | RPB9/AN9 — Remappable I/O / Analog input 9 |
| Chân 11 | VSS — Ground |
| Chân 12 | VDD — Positive supply (2.3-3.6 V) |
| Chân 13 | RPB10/AN10 — Remappable I/O / Analog input 10 |
| Chân 14 | RPB11/AN11 — Remappable I/O / Analog input 11 |
| Chân 15 | RPB12/AN12 — Remappable I/O / Analog input 12 |
| Chân 16 | RPB13/AN13 — Remappable I/O / Analog input 13 |
| Chân 17 | RPB14/AN14 — Remappable I/O / Analog input 14 |
| Chân 18 | RPB15/AN15/OCFB — Remappable I/O / Analog input 15 / Output Compare Fault B |
| Chân 19 | VSS — Ground |
| Chân 20 | VDD — Positive supply (2.3-3.6 V) |
| Chân 21 | RPC0 — Remappable I/O port C0 |
| Chân 22 | RPC1 — Remappable I/O port C1 |
| Chân 23 | RPC2 — Remappable I/O port C2 |
| Chân 24 | RPC3 — Remappable I/O port C3 |
| Chân 25 | RPC4 — Remappable I/O port C4 |
| Chân 26 | RPC5 — Remappable I/O port C5 |
| Chân 27 | RPC6 — Remappable I/O port C6 |
| Chân 28 | RPC7 — Remappable I/O port C7 |
| Chân 29 | RPC8 — Remappable I/O port C8 |
| Chân 30 | RPC9 — Remappable I/O port C9 |
| Chân 31 | VSS — Ground |
| Chân 32 | VDD — Positive supply (2.3-3.6 V) |
| Chân 33 | RPD0/INT0 — Remappable I/O port D0 / External Interrupt 0 |
| Chân 34 | RPD1/INT1 — Remappable I/O port D1 / External Interrupt 1 |
| Chân 35 | RPD2/INT2 — Remappable I/O port D2 / External Interrupt 2 |
| Chân 36 | RPD3/INT3 — Remappable I/O port D3 / External Interrupt 3 |
| Chân 37 | RPD4/INT4 — Remappable I/O port D4 / External Interrupt 4 |
| Chân 38 | RPD5 — Remappable I/O port D5 |
| Chân 39 | RPD6 — Remappable I/O port D6 |
| Chân 40 | RPD7 — Remappable I/O port D7 |
| Chân 41 | RPD8/RTCC — Remappable I/O port D8 / RTCC output |
| Chân 42 | RPD9 — Remappable I/O port D9 |
| Chân 43 | RPD10 — Remappable I/O port D10 |
| Chân 44 | RPD11 — Remappable I/O port D11 |
| Chân 45 | RPD12 — Remappable I/O port D12 |
| Chân 46 | RPD13 — Remappable I/O port D13 |
| Chân 47 | RPD14 — Remappable I/O port D14 |
| Chân 48 | RPD15 — Remappable I/O port D15 |
| Chân 49 | VSS — Ground |
| Chân 50 | VDD — Positive supply (2.3-3.6 V) |
| Chân 51 | RPE0/PMA0 — Remappable I/O port E0 / Parallel Master Port address 0 |
| Chân 52 | RPE1/PMA1 — Remappable I/O port E1 / Parallel Master Port address 1 |
| Chân 53 | RPE2/PMA2 — Remappable I/O port E2 / Parallel Master Port address 2 |
| Chân 54 | RPE3/PMA3 — Remappable I/O port E3 / Parallel Master Port address 3 |
| Chân 55 | RPE4/PMA4 — Remappable I/O port E4 / Parallel Master Port address 4 |
| Chân 56 | RPE5/PMA5 — Remappable I/O port E5 / Parallel Master Port address 5 |
| Chân 57 | RPE6/PMA6 — Remappable I/O port E6 / Parallel Master Port address 6 |
| Chân 58 | RPE7/PMA7 — Remappable I/O port E7 / Parallel Master Port address 7 |
| Chân 59 | RPE8 — Remappable I/O port E8 |
| Chân 60 | VDD — Positive supply (2.3-3.6 V) |
| Chân 61 | VSS — Ground |
| Chân 62 | OSC1/RC1/RA0 — Crystal oscillator input / External clock input / Port A0 |
| Chân 63 | OSC2/RC2/RA1 — Crystal oscillator output / Port A1 |
| Chân 64 | VSS — Ground |
Ứng dụng tiêu biểu
PIC32MX230F128H-50I/PT phù hợp cho 7 Áp dụngs: USB HID Peripherals, CAN Node in Industrial Automation, Consumer Audio with I2S Codec, Low-Cost Graphics Terminal with PMP, USB to UART Bridge, Sensor Hub with I2C/SPI Aggregation, Touch HMI Controller.
USB HID Peripherals
The PIC32MX230F128H-50I/PT is well suited to USB Human Interface Devices such as keyboards, mice, custom HID controls, and USB-to-UART bridges. The integrated USB 2.0 Full-Speed device/host/OTG controller with on-chip transceiver eliminates the need for an external PHY, reducing BOM cost by $0.30-$0.50. The 50 MHz MIPS32 M4K core executing at 83 DMIPS handles the USB stack, HID report descriptor parsing, and debouncing/timing within tight interrupt budgets. Place a 0.1 uF decoupling cap on each VDD pin and route the USB DP/DM traces as a 90 ohm differential pair directly to the connector for signal-integrity compliance with USB 2.0.
Được đề xuất
CAN Node in Industrial Automation
The PIC32MX230F128H-50I/PT integrates a CAN 2.0B controller, allowing it to serve as a slave node on CANopen or DeviceNet networks common in factory automation, building HVAC, and motor control. The 50 MHz core processes CAN message IDs and payloads with deterministic interrupt latency, while the 128 KB Flash holds a full CANopen stack plus application logic. The 16 KB SRAM is sufficient for transmit/receive buffers in mid-density networks. Use Microchip's MCP2551 CAN transceiver between the MCU's CANTX/CANRX pins and the bus, and add a 120 ohm termination resistor at each bus end.
Được đề xuất
Consumer Audio with I2S Codec
The two I2S interfaces on the PIC32MX230F128H-50I/PT enable direct connection to audio DACs and ADCs such as the CS4344 or SGTL5000. The 50 MHz core handles audio sample buffering, EQ, and effect processing at 48 kHz / 24-bit with margin to spare. The Peripheral Pin Select feature lets designers route I2S BCLK, LRCK, and DATA to any available GPIO, simplifying PCB layout when multiple I2S peripherals coexist. Power the codec from a low-noise LDO such as the AP2112-3.3 to keep the analog supply clean and minimize THD+N in the audio path.
Được đề xuất
Low-Cost Graphics Terminal with PMP
The Parallel Master Port (PMP) with dual read/write buffers drives character LCDs, OLED modules, and small TFT controllers without external bus multiplexers. The PIC32MX230F128H-50I/PT can refresh a 320x240 QVGA TFT at 30 fps from a small bitmap buffer in internal RAM, enabling compact HMI panels in appliances and instrument front panels. The 50 MHz MIPS32 core outperforms 8-bit PIC16 parts by 10x in pixel throughput, reducing display-update latency. Keep PMP traces short (under 50 mm) and length-matched to avoid bus-skew issues at higher pixel-clock rates.
Được đề xuất
USB to UART Bridge
The PIC32MX230F128H-50I/PT can be configured as a USB CDC class device to provide a USB-to-UART bridge, replacing the popular FTDI FT232R with a $1-2 BOM cost saving. The integrated USB 2.0 Full-Speed controller and two UART modules allow the part to expose multiple COM ports over USB. The 50 MHz core processes USB bulk transfers at 1 MB/s with low latency. The Microchip MLA USB stack provides ready-to-use CDC firmware that enumerates as a virtual COM port on Windows, macOS, and Linux without additional driver installation on modern OS versions.
Được đề xuất
Sensor Hub with I2C/SPI Aggregation
The PIC32MX230F128H-50I/PT aggregates data from multiple I2C and SPI sensors in industrial sensor hubs, environmental monitors, and wearables. Two I2C controllers and four SPI ports allow simultaneous connection to accelerometers, gyros, pressure, and temperature sensors without external muxes. The 10-bit 1 Msps ADC with up to 28 analog inputs reads thermocouples, strain gauges, and battery voltages on a single chip. The 50 MHz core runs sensor-fusion algorithms and publishes results over USB or CAN at up to 1 kHz update rates, with the 128 KB Flash holding complex filter and calibration tables.
Được đề xuất
Touch HMI Controller
The PIC32MX230F128H-50I/PT combined with Microchip's mTouch capacitive touch library turns the part into a 32-bit touch HMI controller for appliance front panels, IoT devices, and industrial keypads. The 10-bit ADC can be routed to charge-transfer touch channels via the Peripheral Pin Select, supporting up to 16 touch buttons with no external components. The 50 MHz core runs Microchip's mTouch Surface library for sliders and wheels. The wide 2.3-3.6 V supply range tolerates battery-powered operation down to drained Li-ion levels, making the part suitable for portable touch interfaces.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC32MX230F128H-50I/PT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC32MX230F128HT-50I/PT | PIC32MX230F128H-I/PT | PIC32MX130F128H-50I/PT | PIC32MX170F512H-50I/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP (10x10 mm) | 64-pin TQFP (10x10 mm) - same | 64-pin TQFP (10x10 mm) - same | 64-pin TQFP (10x10 mm) - same | 64-pin TQFP (10x10 mm) - same |
| Core Frequency | 50 MHz | 50 MHz | 40 MHz | 50 MHz | 50 MHz |
| Flash Memory | 128 KB | 128 KB | 128 KB | 128 KB | 512 KB |
| SRAM | 16 KB | 16 KB | 16 KB | 16 KB | 64 KB |
| USB | USB 2.0 Full-Speed OTG | USB 2.0 Full-Speed OTG | USB 2.0 Full-Speed OTG | No USB | USB 2.0 Full-Speed OTG |
| CAN | CAN 2.0B | CAN 2.0B | CAN 2.0B | No CAN | No CAN |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) |
| Core Architecture | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K |
Bảo phân biệt quan trọng
- USB 2.0 Full-Speed with on-chip transceiver and CAN 2.0B in a 64-pin TQFP (vsPIC32MX130F128H-50I/PT)
- Higher compute throughput at same Flash size (vsPIC32MX230F128H-I/PT)
- Best balance of Flash density and peripheral mix for USB+CAN designs (vsPIC32MX170F512H-50I/PT)
Ghi chú thiết kế
The PIC32MX230F128H-50I/PT operates from a single 2.3 V to 3.6 V supply and has multiple VDD/VSS pins distributed around the 64-pin TQFP. Place a 0.1 uF decoupling capacitor as close as possible to each VDD pin, plus a single 4.7 uF to 10 uF bulk capacitor near the package. Connect all VSS pins to a solid ground plane. Use a low-noise LDO such as the AP2112-3.3 to derive the 3.3 V rail from a higher system supply, keeping ripple below 50 mVpp to avoid ADC noise coupling.
Do not exceed the absolute maximum 3.6 V on VDD or 4.0 V on any I/O pin - the part is not 5 V tolerant on GPIO. If interfacing to 5 V logic, use a level translator such as the TXS0108E. The USB DP/DM pins are NOT 5 V tolerant and must be protected with USBLC6-2SC6 ESD arrays when routed to an external USB connector. Failing to observe these limits is the most common cause of MCU failures in production designs.
Route the 8 MHz primary oscillator traces (between OSC1/OSC2 and the crystal) as short and symmetric as possible, with the load capacitors (typically 18-22 pF) placed within 5 mm of the crystal pins. Keep the USB DP/DM lines as a 90 ohm differential pair with no stubs, and route them away from switching signals. For PMP-based graphics, match the lengths of PMD[15:0] and PMA[7:0] to within 25 mm to avoid bus skew at higher pixel-clock rates.
The PIC32MX230F128H-50I/PT in 64-pin TQFP (10x10 mm) has a theta_JA of approximately 50 C/W on a standard 4-layer JEDEC test board. At maximum core activity drawing 35 mA from 3.3 V, internal dissipation is around 115 mW, producing a 6 C junction temperature rise above ambient. This is well within safe limits for the industrial -40 C to +85 C grade with no heatsinking required.
Thông tin tuân thủ
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified; for automotive applications, use the PIC32MX series -V variants or migrate to a PIC32MK automotive family member.
