PIC32MX530F128L-50I/PF - 50MHz 32-bit MCU 128KB Flash | Microchip
MPN: PIC32MX530F128L-50I/PF ✓ Hoạt độngPIC32MX530F128L-50I/PF Tóm tắt
A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (Flash), working memory (RAM), and configurable peripherals. The PIC32MX family sits in the hierarchy: microcontroller -> embedded processor -> semiconductor -> integrated circuit. Compared with 8/16-bit MCUs, 32-bit MIPS cores deliver substantially higher throughput (83 DMIPS at 50 MHz), deterministic interrupt latency, and address space large enough for full TCP/IP stacks and graphical user interfaces.
Key features of the PIC32MX530F128L include Peripheral Pin Select (PPS) for flexible pin assignment, a 5-stage pipeline, single-cycle multiply/divide hardware, an 8-channel DMA controller, and a CTMU for capacitive touch and time measurement. The device supports 3.0V-3.6V single-supply operation and offers up to 85 I/O pins on the 100-pin TQFP variant.
Architecturally, the chip uses a Harvard cache with prefetch buffer to minimize Flash wait-state penalties, allowing zero-wait-state execution from Flash up to 30 MHz and one-wait-state up to 50 MHz. The 16 KB on-chip SRAM supports 8 KB DMA-accessible for streaming data, and the PMP module directly drives TFT LCDs and external memories without glue logic.
Typical applications include industrial automation with CAN networks, USB device/host peripherals (HID, CDC, MSD), graphical HMI panels, audio playback with I2S codecs, and embedded web servers. The wide peripheral set makes it well suited for IoT gateways bridging USB sensors to CAN or Ethernet backbones.
When designing with the PIC32MX530F128L-50I/PF, ensure your PCB allocates decoupling within 5 mm of every VDD pin and routes the 50 MHz traces length-matched. Use the PMP module carefully - bus contention during write cycles is a common pitfall when external devices are slow.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet for engineers evaluating 32-bit MCU options.
Bộ thay thế dễ dàng lắp đặt cho PIC32MX530F128L-50I/PF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC32MX530F128L-50I/PF (cùng hình factor và footprint) — khác nhau ở ADC, CTMU, Package, Parallel Master Port (PMP), DMIPS Performance.
PIC32MX530F128LT-50I/PF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX570F512L-50I/PF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX470F512L-50I/PF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX470F256L-50I/PF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX460F256L-80I/PF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX530F128L-50I/PF Tỷ lệ tối đa & tính chất điện
| Core Architecture | MIPS32 M4K |
| Bit Width | 32-bit |
| Maximum CPU Frequency | 50 MHz |
| DMIPS Performance | 83 DMIPS |
| Flash Program Memory | 128 KB |
| SRAM | 16 KB |
| Supply Voltage Range | 3.0 V to 3.6 V |
| Khoảng nhiệt độ hoạt động | -40 C to +85 C (Industrial) |
| Hộp | 100-pin TQFP (14x14 mm) |
| Kiểu lắp đặt | Surface Mount |
| I/O Pins | 85 (maximum) |
| USB Controller | USB 2.0 Full-Speed OTG |
| CAN Controller | CAN 2.0B active |
| SPI/I2S Modules | 4 |
| I2C Modules | 2 |
| ADC | 10-bit, 1 Msps, up to 48 channels |
| Parallel Master Port (PMP) | Yes (dual read/write buffers) |
| DMA Channels | 8 |
| CTMU | Yes (touch and time measurement) |
| Peripheral Pin Select (PPS) | Yes |
| Trạng thái RoHS | Compliant |
| Cấp MSL | 3 (168 hours) |
Cấu hình chân PIC32MX530F128L-50I/PF
| Chân 1 | RG15 — General purpose I/O / PPS |
| Chân 10 | VDD — Positive supply (3.3V) |
| Chân 11 | VSS — Ground reference |
| Chân 12 | RB5 — General purpose I/O / PWM OC2 |
| Chân 13 | RB4 — General purpose I/O / PWM OC1 |
| Chân 14 | RB3 — General purpose I/O / PWM OC4 |
| Chân 15 | RB2 — General purpose I/O / PWM OC3 |
| Chân 16 | RB1 — General purpose I/O / PWM OC2 |
| Chân 17 | RB0 — General purpose I/O / Programmer PGED1 |
| Chân 18 | RB6 — General purpose I/O / Programmer PGEC1 |
| Chân 19 | RB7 — General purpose I/O |
| Chân 2 | RG0 — General purpose I/O / PMP |
| Chân 20 | RB8 — General purpose I/O |
| Chân 21 | RB9 — General purpose I/O |
| Chân 22 | RB10 — General purpose I/O |
| Chân 23 | RB11 — General purpose I/O |
| Chân 24 | RB12 — General purpose I/O |
| Chân 25 | RB13 — General purpose I/O |
| Chân 26 | RB14 — General purpose I/O |
| Chân 27 | RB15 — General purpose I/O |
| Chân 28 | RD8 — General purpose I/O / PMP |
| Chân 29 | RD9 — General purpose I/O / PMP |
| Chân 3 | RG1 — General purpose I/O / PMP |
| Chân 30 | RD10 — General purpose I/O / PMP |
| Chân 31 | RD11 — General purpose I/O / PMP |
| Chân 32 | RD12 — General purpose I/O / PMP |
| Chân 33 | RD13 — General purpose I/O / PMP |
| Chân 34 | RD14 — General purpose I/O / PMP |
| Chân 35 | RD15 — General purpose I/O / PMP |
| Chân 36 | RC13 — General purpose I/O |
| Chân 37 | RC14 — General purpose I/O / DMA |
| Chân 38 | VDD — Positive supply (3.3V) |
| Chân 39 | VSS — Ground reference |
| Chân 4 | RG2 — General purpose I/O / PMP |
| Chân 40 | RF0 — General purpose I/O / USB VBUS |
| Chân 41 | RF1 — General purpose I/O / USB D- |
| Chân 42 | RF2 — General purpose I/O / USB D+ |
| Chân 43 | RF3 — General purpose I/O / USB VBUS |
| Chân 44 | RF4 — General purpose I/O |
| Chân 45 | RF5 — General purpose I/O |
| Chân 46 | RF6 — General purpose I/O |
| Chân 47 | RF7 — General purpose I/O |
| Chân 48 | RF8 — General purpose I/O |
| Chân 49 | RG6 — General purpose I/O / SCLK2 |
| Chân 5 | RG3 — General purpose I/O / PMP |
| Chân 50 | RG7 — General purpose I/O / SCLK1 |
| Chân 51 | RG8 — General purpose I/O / SCLK3 |
| Chân 52 | RG9 — General purpose I/O / SCLK4 |
| Chân 53 | MCLR — Master clear reset (active low) |
| Chân 54 | VSS — Ground reference |
| Chân 55 | VDD — Positive supply (3.3V) |
| Chân 56 | RA0 — General purpose I/O / Oscillator |
| Chân 57 | RA1 — General purpose I/O / Oscillator |
| Chân 58 | RA2 — General purpose I/O |
| Chân 59 | RA3 — General purpose I/O |
| Chân 6 | RG12 — General purpose I/O / UART2 |
| Chân 60 | RA4 — General purpose I/O |
| Chân 61 | RA5 — General purpose I/O |
| Chân 62 | RA6 — General purpose I/O |
| Chân 63 | RA7 — General purpose I/O |
| Chân 64 | RA8 — General purpose I/O |
| Chân 65 | RA9 — General purpose I/O |
| Chân 66 | RA10 — General purpose I/O |
| Chân 67 | RA11 — General purpose I/O |
| Chân 68 | RA12 — General purpose I/O |
| Chân 69 | RA13 — General purpose I/O |
| Chân 7 | RG13 — General purpose I/O / SCLK4 |
| Chân 70 | RA14 — General purpose I/O |
| Chân 71 | RA15 — General purpose I/O |
| Chân 72 | VDD — Positive supply (3.3V) |
| Chân 73 | VSS — Ground reference |
| Chân 74 | RC1 — General purpose I/O |
| Chân 75 | RC2 — General purpose I/O |
| Chân 76 | RC3 — General purpose I/O / SPI2 |
| Chân 77 | RC4 — General purpose I/O / SPI2 |
| Chân 78 | RD0 — General purpose I/O / INT0 |
| Chân 79 | RD1 — General purpose I/O / INT1 |
| Chân 8 | RG14 — General purpose I/O / UART2 |
| Chân 80 | RD2 — General purpose I/O / INT2 |
| Chân 81 | RD3 — General purpose I/O / INT3 |
| Chân 82 | RD4 — General purpose I/O / OC5 |
| Chân 83 | RD5 — General purpose I/O / OC6 |
| Chân 84 | RD6 — General purpose I/O / OC7 |
| Chân 85 | RD7 — General purpose I/O / OC8 |
| Chân 86 | RC0 — General purpose I/O |
| Chân 87 | RC5 — General purpose I/O |
| Chân 88 | RC6 — General purpose I/O |
| Chân 89 | RC7 — General purpose I/O |
| Chân 9 | RC8 — General purpose I/O |
| Chân 90 | RC9 — General purpose I/O |
| Chân 91 | RE0 — General purpose I/O / PWM |
| Chân 92 | RE1 — General purpose I/O / PWM |
| Chân 93 | RE2 — General purpose I/O / PWM |
| Chân 94 | RE3 — General purpose I/O / PWM |
| Chân 95 | RE4 — General purpose I/O / PWM |
| Chân 96 | RE5 — General purpose I/O / PWM |
| Chân 97 | RE6 — General purpose I/O / PWM |
| Chân 98 | RE7 — General purpose I/O / PWM |
| Chân 99 | VDD — Positive supply (3.3V) |
| Chân 100 | VSS — Ground reference |
Ứng dụng tiêu biểu
PIC32MX530F128L-50I/PF phù hợp cho 6 Áp dụngs: Industrial CAN/USB Gateway, USB HID / CDC Peripherals, Graphical HMI Panels with TFT LCD, I2S Audio Playback Devices, IoT Sensor Aggregation Hubs, Motor Control with CANopen.
Industrial CAN/USB Gateway
The PIC32MX530F128L-50I/PF combines a CAN 2.0B active controller and USB 2.0 Full-Speed OTG controller on a single die, making it ideal for industrial gateway nodes that bridge USB sensors (HID, CDC, MSD) to a CAN backbone. The 50 MHz MIPS32 M4K core delivers 83 DMIPS - sufficient to handle CANopen or DeviceNet protocol stacks at 1 Mbit/s alongside a USB device class stack. With 128 KB Flash and 16 KB SRAM, the part can host a small TCP/IP-over-CAN gateway with comfortable firmware headroom. Its industrial -40C to +85C temperature grade and 3.3V single-supply operation make it suitable for factory-floor equipment. Place a common-mode choke on the CANH/CANL lines and add a USB ferrite bead at the connector to meet IEC 61000-4-2 ESD/EMI requirements.
Được đề xuất
USB HID / CDC Peripherals
The integrated USB 2.0 Full-Speed OTG controller eliminates the need for an external PHY or external transceiver, reducing BOM cost and PCB area in HID input devices (keyboards, mice, custom controls), CDC serial bridges, and MSD storage devices. The Microchip USB stack provides ready-made class drivers, and the 16 KB SRAM plus 8 KB DMA-accessible buffer can sustain full-speed 12 Mbit/s streams without CPU intervention. The 50 MHz core easily handles HID report generation at 1 kHz polling rates while running application logic. PPS allows the USB D+/D- pins to be remapped if routing gets tight. Recommend ESD protection diodes (USBLC6-2SC6) on the D+/D- lines for production-grade immunity.
Được đề xuất
Graphical HMI Panels with TFT LCD
The Parallel Master Port (PMP) on the PIC32MX530F128L-50I/PF directly drives TFT LCDs up to 16-bit parallel interface without external bus drivers, simplifying BOM and layout for graphical HMI panels. Dual read/write buffers allow concurrent CPU and DMA PMP transactions, supporting up to 30 Hz refresh at QVGA resolution. Combined with the 50 MHz core, the chip can run a small graphics library (UGUI, LVGL ported to PIC32) and a touch-screen interface via the CTMU. The 128 KB Flash holds fonts and bitmaps; 16 KB SRAM fits a small framebuffer. Industrial temperature grade and PPS flexibility make it suitable for white-goods and appliance controls.
Được đề xuất
I2S Audio Playback Devices
The four SPI/I2S modules on the PIC32MX530F128L-50I/PF enable connection to external audio codecs for full-duplex stereo playback and recording at up to 192 kHz sample rates. A DMA-driven I2S implementation can stream PCM data from external serial Flash without CPU loading, leaving the MIPS32 M4K core free for user-interface logic. Typical applications include voice prompt modules, simple MP3/WAV player appliances, and intercom endpoints. The 16 KB RAM accommodates roughly 30 ms of 48 kHz stereo buffer, sufficient for short effects and gapless playback with double-buffering.
Được đề xuất
IoT Sensor Aggregation Hubs
The PIC32MX530F128L-50I/PF acts as a low-cost aggregation hub for IoT sensor nodes, collecting data via I2C sensors, SPI peripherals, and analog inputs (up to 48 ADC channels), then forwarding aggregated data over USB or CAN. The 8-channel DMA engine allows background movement of sensor data without disturbing application code, while the 50 MHz MIPS32 M4K core runs TCP/IP stacks or local analytics. With 128 KB Flash and 16 KB RAM, the chip can host a TLS-lite implementation for secure upstream links. The industrial temperature grade and 3.3V operation simplify integration with battery or line-powered sensor arrays.
Được đề xuất
Motor Control with CANopen
The PIC32MX530F128L-50I/PF delivers sufficient compute (83 DMIPS at 50 MHz) and peripheral integration (CAN 2.0B, PWM via OC, ADC with 1 Msps) for low-cost CANopen slave nodes driving stepper or BLDC motors. The CTMU provides accurate current sensing timing when paired with sense resistors, and PPS allows flexible pin assignment of PWM and feedback signals. With 128 KB Flash, a full CANopen CiA 301 stack plus application logic fits comfortably. The 100-pin TQFP package exposes enough I/O to handle encoder inputs, Hall sensors, and the CAN interface simultaneously.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC32MX530F128L-50I/PF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC32MX530F128LT-50I/PF | PIC32MX570F512L-50I/PF | PIC32MX470F512L-50I/PF | PIC32MX470F256L-50I/PF | PIC32MX460F256L-80I/PF |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-pin TQFP (14x14 mm) | 100-pin TQFP (14x14 mm) - same | 100-pin TQFP (14x14 mm) - same | 100-pin TQFP (14x14 mm) - same | 100-pin TQFP (14x14 mm) - same | 100-pin TQFP (14x14 mm) - same |
| Maximum CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 80 MHz |
| Flash Memory | 128 KB | 128 KB | 512 KB | 512 KB | 256 KB | 256 KB |
| SRAM | 16 KB | 16 KB | 64 KB | 64 KB | 32 KB | 32 KB |
| USB Controller | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | None (has Ethernet MAC) | None (has Ethernet MAC) | USB 2.0 FS OTG |
| CAN 2.0B | Yes | Yes | Yes | Yes | Yes | Yes |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| DMIPS | 83 DMIPS | 83 DMIPS | 83 DMIPS | 83 DMIPS | 83 DMIPS | 124 DMIPS |
Bảo phân biệt quan trọng
- Combined USB OTG and CAN 2.0B on a single die (vsPIC32MX470F512L-50I/PF)
- Compact 128 KB Flash footprint with 16 KB RAM (vsPIC32MX570F512L-50I/PF)
- Industrial -40C to +85C operating range in -50I grade (vsPIC32MX530F128L-50V/PF)
- Integrated PMP graphics interface with dual buffers (vsPIC32MX230F256B-I/SP)
Ghi chú thiết kế
Place one 0.1 uF ceramic decoupling capacitor within 5 mm of every VDD pin (pin 10, 38, 55, 72, 99) and one bulk 10 uF tantalum or ceramic capacitor at the board's VDD entry point. The PIC32MX530F128L-50I/PF draws up to 70 mA peak during USB Full-Speed activity; a low-ESR regulator with at least 200 mA headroom is recommended. Do not power from a switching regulator output directly without LC filtering - the analog ADC reference is sensitive to ripple above 50 mV pk-pk.
Route the 50 MHz crystal traces (pins 56-57) symmetrically and keep them shorter than 10 mm to avoid stray radiation. The USB D+/D- differential pair (pins 41-42) must be routed with 90-ohm differential impedance, matched within 2 mm, and kept away from high-speed switching nodes. The MCLR reset line (pin 53) should have a 10 kohm pull-up and a 100 nF to ground for noise immunity per Microchip guidance.
Do not exceed 3.6V on any VDD pin - the Flash programming voltage margin disappears above 3.6V, causing flash corruption. The PMP module can stall the CPU if the external peripheral holds wait states too long; use external logic to back-pressure the bus. The CTMU current source requires calibration per chip and should not be assumed constant across temperature. Always check the published silicon errata sheet before locking down the firmware design.
Allocate dedicated ground pours under the MCU to provide low-impedance return paths for high-speed signals. The 100-pin TQFP has a thermal pad requirement of at least 4 vias to the internal ground plane. Separate analog ground (AVSS) from digital ground (VSS) at the regulator and join at a single point near the MCU. Do not route switching regulator traces directly under the analog ADC inputs (e.g., AN0/AN1) - coupling can degrade ADC accuracy by 2-3 LSBs.
Thông tin tuân thủ
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified - this part targets industrial and consumer markets, not automotive safety-critical applications. For AEC-Q100 qualified PIC32 options, refer to PIC32MK or PIC32MX1/2/5xx with -VAuto suffix.
