PIC32MX775F512HT-80V/PT - 80MHz 512KB Flash MCU w/ USB-OTG | Microchip
MPN: PIC32MX775F512HT-80V/PT ✓ Hoạt độngPIC32MX775F512HT-80V/PT Tóm tắt
A 32-bit MCU (microcontroller unit) is an integrated circuit containing a processor core, program memory (Flash), data memory (SRAM), and a rich mix of peripherals (USB, CAN, Ethernet, ADC, timers, GPIO). Compared with 8- or 16-bit MCUs, 32-bit parts execute instructions on wider registers, allowing faster arithmetic and more deterministic handling of communication stacks. The PIC32MX5/6/7 family specifically targets connected applications by integrating high-bandwidth peripherals (USB-OTG, Ethernet, dual CAN) that previously required an external MCU plus dedicated controller ICs.
Key features include 512KB Flash organized as 512K x 8, 64KB SRAM, 51 usable I/O pins, four-wire SPI, I2C, dual CAN 2.0b, USB-OTG, 10/100 Mbps Ethernet MAC, 16-channel 10-bit ADC at 1 Msps, a 16-bit parallel master port, and a 4-channel DMA. The part operates from 2.3V to 3.6V, supports industrial temperature range (-40C to +105C), and is pin-compatible with most PIC24/dsPIC DSC devices in the same package footprint.
The MIPS32 M4K core provides single-cycle multiplication, hardware divide, and a five-stage pipeline, delivering 1.56 DMIPS/MHz. Multiple power management modes (idle, sleep, deep sleep) and the Fail-Safe Clock Monitor reduce dynamic and standby power. Interrupt latency is deterministic and individually programmable in priority, which simplifies real-time fieldbus handling.
Typical applications include industrial Ethernet gateways, CAN-based automotive body controllers, USB-OTG medical peripherals, building-automation controllers, and connected sensors in IoT edge nodes. The combination of Ethernet MAC, dual CAN, and USB-OTG in a single MCU removes the need for external interface bridges and shortens BOM cost.
When designing with this part, plan the clock tree carefully - the 80MHz SYSCLK requires an 8MHz primary oscillator with on-chip PLL. Decouple VDDCORE pins with 1uF and 0.1uF ceramics close to the package and keep the analog AVdd rail separate to preserve ADC SNR.
This page synthesizes distributor stock and pricing, lists pin-compatible drop-in alternatives from the same PIC32MX7 family, and provides practical design notes you will not see in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho PIC32MX775F512HT-80V/PT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC32MX775F512HT-80V/PT (cùng hình factor và footprint) — khác nhau ở ADC, Package, CAN, I/O Pins, Core Architecture.
PIC32MX775F512H-80V/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX775F512HT-80V/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX775F512HT-80I/PT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX795F512L-80V/PT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX675F512H-80V/PT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX575F512H-80V/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX775F512HT-80V/PT Tỷ lệ tối đa & tính chất điện
| Architecture | MIPS32 M4K 32-bit RISC |
| Maximum CPU Clock | 80 MHz |
| Program Memory (Flash) | 512 KB (512K x 8) |
| Data Memory (SRAM) | 64 KB |
| Operating Voltage Range | 2.3 V to 3.6 V |
| I/O Pins | 51 |
| ADC | 10-bit, 16-channel, up to 1 Msps |
| USB | USB 2.0 Full-Speed OTG |
| CAN | 2x CAN 2.0b |
| Ethernet | 10/100 Mbps MAC |
| DMA Channels | 4 |
| Parallel Master Port | 16-bit |
| Timers | 5x 16-bit, 2x 32-bit |
| Nhiệt độ hoạt động | -40 C to +105 C (industrial) |
| Hộp | 64-pin TQFP (10x10 mm), 0.5 mm pitch |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
| Cấp MSL | 3 (168 hours) |
Cấu hình chân PIC32MX775F512HT-80V/PT
| Chân 1 | RPB0/AN0 — Remappable peripheral B0 / Analog input 0 |
| Chân 2 | RPB1/AN1 — Remappable peripheral B1 / Analog input 1 |
| Chân 3 | RPB2/AN2 — Remappable peripheral B2 / Analog input 2 |
| Chân 4 | RPB3/AN3 — Remappable peripheral B3 / Analog input 3 |
| Chân 5 | RPB4/AN4 — Remappable peripheral B4 / Analog input 4 |
| Chân 6 | RPB5/AN5 — Remappable peripheral B5 / Analog input 5 |
| Chân 7 | RPB6/AN6 — Remappable peripheral B6 / Analog input 6 |
| Chân 8 | RPB7/AN7 — Remappable peripheral B7 / Analog input 7 |
| Chân 9 | RPB8/AN8 — Remappable peripheral B8 / Analog input 8 |
| Chân 10 | RPB9/AN9 — Remappable peripheral B9 / Analog input 9 |
| Chân 11 | VSS — Ground |
| Chân 12 | VDD — Digital supply 2.3V-3.6V |
| Chân 13 | RPA1 — Remappable peripheral A1 |
| Chân 14 | RPA2 — Remappable peripheral A2 |
| Chân 15 | RPA3 — Remappable peripheral A3 |
| Chân 16 | RPB10 — Remappable peripheral B10 |
| Chân 17 | RPB11 — Remappable peripheral B11 |
| Chân 18 | VSS — Ground |
| Chân 19 | VDD — Digital supply 2.3V-3.6V |
| Chân 20 | RPB12 — Remappable peripheral B12 |
| Chân 21 | RPB13 — Remappable peripheral B13 |
| Chân 22 | RPB14 — Remappable peripheral B14 |
| Chân 23 | RPB15 — Remappable peripheral B15 |
| Chân 24 | VSS — Ground |
| Chân 25 | VDD — Digital supply 2.3V-3.6V |
| Chân 26 | RPC0 — Remappable peripheral C0 |
| Chân 27 | RPC1 — Remappable peripheral C1 |
| Chân 28 | RPC2 — Remappable peripheral C2 |
| Chân 29 | RPC3 — Remappable peripheral C3 |
| Chân 30 | RPC4 — Remappable peripheral C4 |
| Chân 31 | RPC5 — Remappable peripheral C5 |
| Chân 32 | RPC6 — Remappable peripheral C6 |
| Chân 33 | RPC7 — Remappable peripheral C7 |
| Chân 34 | RPC8 — Remappable peripheral C8 |
| Chân 35 | RPC9 — Remappable peripheral C9 |
| Chân 36 | VSS — Ground |
| Chân 37 | VDD — Digital supply 2.3V-3.6V |
| Chân 38 | AVDD — Analog supply 2.3V-3.6V |
| Chân 39 | AVSS — Analog ground |
| Chân 40 | AN10 — Analog input 10 |
| Chân 41 | AN11 — Analog input 11 |
| Chân 42 | AN12 — Analog input 12 |
| Chân 43 | AN13 — Analog input 13 |
| Chân 44 | AN14 — Analog input 14 |
| Chân 45 | AN15 — Analog input 15 |
| Chân 46 | VDD — Digital supply 2.3V-3.6V |
| Chân 47 | OSC1/CLKI — Crystal input / external clock |
| Chân 48 | OSC2/CLKO — Crystal output |
| Chân 49 | VSS — Ground |
| Chân 50 | TMS — JTAG test mode select |
| Chân 51 | TCK — JTAG test clock |
| Chân 52 | TDI — JTAG test data in |
| Chân 53 | TDO — JTAG test data out |
| Chân 54 | MCLR — Master clear / reset (active-low) |
| Chân 55 | RPA0 — Remappable peripheral A0 |
| Chân 56 | RPA4 — Remappable peripheral A4 |
| Chân 57 | RPA5 — Remappable peripheral A5 |
| Chân 58 | RPA6 — Remappable peripheral A6 |
| Chân 59 | RPA7 — Remappable peripheral A7 |
| Chân 60 | RPA8 — Remappable peripheral A8 |
| Chân 61 | RPA9 — Remappable peripheral A9 |
| Chân 62 | VSS — Ground |
| Chân 63 | VDD — Digital supply 2.3V-3.6V |
| Chân 64 | ENVREG — Voltage regulator enable (connect to VDD) |
Ứng dụng tiêu biểu
PIC32MX775F512HT-80V/PT phù hợp cho 6 Áp dụngs: Industrial Ethernet Gateway, CAN-Based Automotive Body Controller, USB-OTG Medical Peripheral, Building Automation Controller, Connected IoT Edge Sensor Node, Industrial HMI Touch Panel.
Industrial Ethernet Gateway
The PIC32MX775F512HT-80V/PT's integrated 10/100 Mbps Ethernet MAC and 80MHz MIPS32 M4K core make it ideal for industrial Ethernet gateways such as Modbus TCP and EtherNet/IP slave nodes. Placed between the fieldbus side (RS485 transceiver) and the network side (Ethernet PHY + RJ45), the MCU runs a TCP/IP stack in parallel with a real-time OS without external bridge ICs. Its 512KB Flash accommodates the full Microchip Harmony TCP/IP stack plus application logic, while the 4-channel DMA offloads Ethernet packet copies to keep CPU utilization below 60 percent. The 2.3V-3.6V industrial voltage range and -40C to +105C operating temperature support 24V factory-floor environments.
Được đề xuất
CAN-Based Automotive Body Controller
With dual CAN 2.0b controllers and 16-channel 10-bit ADC, the PIC32MX775F512HT-80V/PT fits CAN-based body controllers managing door modules, lighting clusters, or seat controllers. Each CAN channel drives a separate bus (for example, body CAN and chassis CAN), while the ADC samples battery voltage, lighting feedback, and temperature sensors at up to 1 Msps. The 64KB SRAM buffers complete CAN frames before forwarding to the gateway ECU. The part's industrial temperature grade (-40C to +105C) is sufficient for cabin-mounted ECUs; pair with an external CAN transceiver such as MCP2551 or TJA1050 for the physical layer.
Được đề xuất
USB-OTG Medical Peripheral
The PIC32MX775F512HT-80V/PT's USB 2.0 Full-Speed OTG controller supports both device and host roles on a single port, ideal for medical peripherals such as patient monitors, infusion pumps, or portable diagnostics. In device mode, the MCU streams patient data over USB CDC or vendor-class to a host PC; in host mode, it enumerates a USB flash drive for log export. The 51 GPIOs interface with LCDs, keypads, and sensor front-ends. The 10-bit ADC digitizes analog sensor channels at 1 Msps with adequate resolution for physiological-signal conditioning pre-filters.
Được đề xuất
Building Automation Controller
Building-automation controllers for HVAC, lighting, and access-control subsystems benefit from the PIC32MX775F512HT-80V/PT's mix of dual CAN, Ethernet, and USB-OTG on a single MCU. The Ethernet MAC links the controller to the building's BACnet/IP or Modbus TCP backbone, while dual CAN runs the field-level MS/TP device bus for distributed I/O. The 512KB Flash holds the BACnet stack plus graphical HMI logic, and the 16-bit PMP drives character or TFT LCDs. Industrial temperature grade permits unheated equipment-room installations.
Được đề xuất
Connected IoT Edge Sensor Node
For IoT edge nodes aggregating sensor data and pushing to a cloud gateway, the PIC32MX775F512HT-80V/PT integrates Ethernet and USB-OTG for both wired IP and cellular-modem attachment. The 4-channel DMA moves ADC samples into memory without CPU intervention, leaving the 80MHz MIPS core free for stack processing, JSON formatting, and TLS handshake acceleration. The 51 I/Os interface with multiple sensor buses (I2C, SPI, UART), and the 12KB boot Flash supports secure OTA firmware updates.
Được đề xuất
Industrial HMI Touch Panel
The PIC32MX775F512HT-80V/PT supports industrial HMI touch panels through its 16-bit Parallel Master Port (PMP) for direct interface to TFT LCDs and resistive-touch controllers. The 80MHz core drives QVGA panels at 30 fps while running Modbus or EtherNet/IP. The 64KB SRAM holds double-buffered framebuffers, and the 4-channel DMA accelerates screen updates. The 51 GPIOs multiplex LED backlight, keypad, and rotary encoder inputs alongside the PMP data bus.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC32MX775F512HT-80V/PT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC32MX775F512H-80V/PT | PIC32MX775F512HT-80V/MR | PIC32MX775F512HT-80I/PT | PIC32MX795F512L-80V/PT | PIC32MX675F512H-80V/PT | PIC32MX575F512H-80V/PT |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-64 (10x10 mm) | TQFP-64 (same) | TQFP-64 (same) | TQFP-64 (same) | TQFP-64 (same) | TQFP-64 (same) | TQFP-64 (same) |
| Flash | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB |
| SRAM | 64 KB | 64 KB | 64 KB | 64 KB | 128 KB (+100%) | 64 KB | 64 KB |
| USB-OTG | Yes | Yes | Yes | Yes | Yes | Yes | No (USB-FS only) |
| CAN Controllers | 2 | 2 | 2 | 2 | 2 | 2 | 1 (-1) |
| Ethernet MAC | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | No | No |
| CPU Clock | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Operating Voltage | 2.3V-3.6V | 2.3V-3.6V | 2.3V-3.6V | 2.3V-3.6V | 2.3V-3.6V | 2.3V-3.6V | 2.3V-3.6V |
| Temperature Range | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +85C | -40C to +105C | -40C to +105C | -40C to +105C |
Bảo phân biệt quan trọng
- Triple-stack connectivity on one die (vsPIC32MX675F512H-80V/PT)
- Double the SRAM vs PIC32MX675 (vsPIC32MX795F512L-80V/PT)
- Industrial temperature range -40C to +105C (vsPIC32MX775F512HT-80I/PT)
Ghi chú thiết kế
Decouple VDDCORE pins (one or more per package) with a 1uF X7R ceramic plus a parallel 0.1uF X7R ceramic placed within 3 mm of the pins. Keep the AVDD rail sourced through a ferrite bead from VDD, with its own 10uF + 0.1uF pair, to keep ADC noise below 1 LSB. ENVREG (pin 64) must be tied to VDD; do not leave it floating or the internal 1.8V regulator will not start.
Route the 80MHz SYSCLK source (8MHz crystal + PLL) on the shortest possible trace between the crystal load capacitors (typically 18 pF for 8 MHz fundamental) and pins 47-48. Place the EZCN crystal within 5 mm of the package and guard the traces with a ground pour. The Ethernet RMII traces to the LAN8742A PHY must be length-matched within 2 mm and routed over an unbroken ground plane to meet 100 Mbps signal-integrity margins.
At 80 MHz the PIC32MX775F512HT-80V/PT draws approximately 90 mA from VDD (3.3V), so steady-state dissipation is about 300 mW. The 64-pin TQFP theta_JA is around 50 C/W, so junction temperature rise is roughly 15 C above ambient at room temperature. Industrial-grade operation up to +105 C ambient is feasible without a heatsink, but above +85 C ambient consider routing additional copper pour on VDD/VSS planes.
Do not connect JTAG pins TMS/TCK/TDI/TDO to external pull-ups or pull-downs unless absolutely required; the on-chip pull-ups are enabled by default. The MCLR pin (54) requires a 10 kohm pull-up to VDD and a 100 nF cap to ground for in-circuit Serial Programming (ICSP). Forgetting the MCLR pull-up causes intermittent reset failures during programming.
USB-OTG differential pair (DP/DM) requires 90 ohm differential impedance and equal-length traces; place the 15 kohm pull-down on D+ for full-speed device mode. For host mode add a 15 kohm pull-up on D+ or D- (full/low speed detection). EMC compliance: place ferrite beads on VDD and AVDD near the MCU when designing for industrial EN 55022 Class B emissions.
Thông tin tuân thủ
RoHS compliant per Microchip product page; lead-free TQFP finish. Not AEC-Q100 qualified - this part targets industrial applications, not automotive under-hood.
