PIC32MZ1024EFF144-E/PL - 200MHz 1MB Flash MCU 144-LQFP | Microchip
MPN: PIC32MZ1024EFF144-E/PL ✓ Hoạt độngPIC32MZ1024EFF144-E/PL Tóm tắt
A 32-bit MCU is a microprocessor whose internal data path, registers, and ALU are 32 bits wide, enabling efficient handling of large integer and floating-point workloads. PIC32 microcontrollers belong to the MIPS architecture family and target embedded connectivity applications that demand deterministic real-time response combined with rich peripheral integration. The PIC32MZ EF family is positioned at the top of Microchip's PIC32 lineup, sitting between the lower-end PIC32MX devices and the higher-end SAME70 SAM Cortex-M7 family in performance, while retaining Microchip's MPLAB Harmony toolchain and peripheral library.
Key features include HS USB 2.0 with integrated PHY, 10/100 Ethernet MAC with MII/RMII interface, two CAN 2.0B modules, multiple UART/SPI/I2C peripherals, a 12-bit 18 MSPS ADC, up to 16 channels of DMA, and an SQI (Serial Quad Interface) for high-speed external Flash. The 144-LQFP footprint exposes the maximum number of I/O and peripheral pins in this family variant.
The dual-panel Live-Update Flash architecture allows firmware to be written to one panel while executing from the other, enabling fail-safe over-the-air (OTA) updates for connected industrial and IoT systems. Hardware crypto accelerators (when present in the EFF suffix variants) support AES, DES, SHA, and HMAC, while the EF (non-crypto) variants are pin-compatible and lower cost.
Typical applications include industrial gateways with Ethernet and CAN, IoT edge nodes with secure cloud connectivity, automotive infotainment HMI controllers, motor control FOC drives, audio processing and graphics HMI panels, and point-of-sale terminals. The integrated FPU accelerates DSP workloads such as audio codecs, motor control loops, and FFT signal processing without offloading to a companion DSP.
When designing with the PIC32MZ1024EFF144-E/PL, ensure the core supply uses a low-noise LDO and that VDDPLL/VBAT/VUSB decoupling follows the reference manual. Use MPLAB Harmony 3 configuration to avoid pin-mapping conflicts between the 144-LQFP, 100-TQFP, and 64-QFN variants of the same family.
This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet, enabling faster part selection and BOM risk reduction.
Bộ thay thế dễ dàng lắp đặt cho PIC32MZ1024EFF144-E/PL — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC32MZ1024EFF144-E/PL (cùng hình factor và footprint) — khác nhau ở Core Architecture, Operating Temperature, Package, ADC, Ethernet.
PIC32MZ1024EFF144-I/PL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MZ1024EFF144T-E/PL
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MZ1024EFE144-I/PL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MZ1024EFE144-E/PH
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MZ0512EFF144-E/PL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MZ1024EFF144-E/JWX
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MZ1024EFF144-E/PL Tỷ lệ tối đa & tính chất điện
| Core Architecture | MIPS32 Warrior M-Class |
| CPU Core | MIPS Warrior M-class, 32-bit RISC with FPU and DSP |
| Maximum CPU Frequency | 200 MHz |
| DMIPS Performance | 330 DMIPS |
| Program Flash Memory | 1 MB (1024 KB) |
| SRAM | 256 KB |
| FPU | IEEE 754-compliant, single and double precision |
| DSP Extensions | Single-cycle MAC, four 64-bit accumulators, saturating/fractional math |
| Live-Update Flash | Dual-panel, supports firmware update without CPU halt |
| Hộp | 144-LQFP (20x20 mm) |
| Nhiệt độ hoạt động | -40C to +125C (extended, -E suffix) |
| Điện áp cung cấp | 2.3 V to 3.6 V |
| Ethernet | 10/100 MAC with MII/RMII interface |
| USB | USB 2.0 High-Speed with integrated PHY |
| CAN | 2x CAN 2.0B |
| ADC | 12-bit, up to 18 MSPS |
| SQI | Serial Quad Interface for external Flash |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC32MZ1024EFF144-E/PL
| Chân 1 | RG15 — General purpose I/O / peripheral function |
| Chân 2 | VDD — Supply voltage 2.3-3.6V |
| Chân 3 | RP14 — Remappable peripheral I/O |
| Chân 4 | RG6 — General purpose I/O |
| Chân 5 | VSS — Ground |
| Chân 6 | RC1 — General purpose I/O |
| Chân 7 | RB5 — General purpose I/O |
| Chân 8 | RB4 — General purpose I/O |
| Chân 9 | RB3 — General purpose I/O |
| Chân 10 | RB2 — General purpose I/O |
| Chân 11 | RB1 — General purpose I/O |
| Chân 12 | RB0 — General purpose I/O |
| Chân 13 | RA6 — General purpose I/O |
| Chân 14 | RA7 — General purpose I/O |
| Chân 15 | VSS — Ground |
| Chân 16 | VDD — Supply voltage |
| Chân 17 | RB6 — General purpose I/O |
| Chân 18 | RB7 — General purpose I/O |
| Chân 19 | RC2 — General purpose I/O |
| Chân 20 | RC3 — General purpose I/O |
| Chân 21 | RC4 — General purpose I/O |
| Chân 22 | RD5 — General purpose I/O |
| Chân 23 | RD4 — General purpose I/O |
| Chân 24 | RD3 — General purpose I/O |
| Chân 25 | RD2 — General purpose I/O |
| Chân 26 | RD1 — General purpose I/O |
| Chân 27 | RD0 — General purpose I/O |
| Chân 28 | RF13 — General purpose I/O |
| Chân 29 | RF12 — General purpose I/O |
| Chân 30 | VSS — Ground |
| Chân 31 | VDD — Supply voltage |
| Chân 32 | RF5 — General purpose I/O |
| Chân 33 | RF4 — General purpose I/O |
| Chân 34 | RD15 — General purpose I/O |
| Chân 35 | RD14 — General purpose I/O |
| Chân 36 | RD13 — General purpose I/O |
| Chân 37 | RD12 — General purpose I/O |
| Chân 38 | RD11 — General purpose I/O |
| Chân 39 | RD10 — General purpose I/O |
| Chân 40 | RD9 — General purpose I/O |
| Chân 41 | RD8 — General purpose I/O |
| Chân 42 | RC14 — General purpose I/O |
| Chân 43 | RC13 — General purpose I/O |
| Chân 44 | VSS — Ground |
| Chân 45 | VDD — Supply voltage |
| Chân 46 | RG14 — General purpose I/O |
| Chân 47 | RG12 — General purpose I/O |
| Chân 48 | RG13 — General purpose I/O |
| Chân 49 | RC15 — General purpose I/O |
| Chân 50 | RA0 — General purpose I/O |
| Chân 51 | RA1 — General purpose I/O |
| Chân 52 | RA2 — General purpose I/O |
| Chân 53 | RA3 — General purpose I/O |
| Chân 54 | RA4 — General purpose I/O |
| Chân 55 | RA5 — General purpose I/O |
| Chân 56 | VSS — Ground |
| Chân 57 | VDD — Supply voltage |
| Chân 58 | RF3 — General purpose I/O |
| Chân 59 | RF2 — General purpose I/O |
| Chân 60 | RF1 — General purpose I/O |
| Chân 61 | RF0 — General purpose I/O |
| Chân 62 | RD7 — General purpose I/O |
| Chân 63 | RD6 — General purpose I/O |
| Chân 64 | RF8 — General purpose I/O |
| Chân 65 | RF7 — General purpose I/O |
| Chân 66 | VBAT — Battery backup supply for RTCC |
| Chân 67 | VREF+ — ADC reference voltage positive |
| Chân 68 | VREF- — ADC reference voltage negative |
| Chân 69 | AVDD — Analog supply voltage |
| Chân 70 | AVSS — Analog ground |
| Chân 71 | RF6 — General purpose I/O |
| Chân 72 | RG7 — General purpose I/O |
| Chân 73 | RG8 — General purpose I/O |
| Chân 74 | RG9 — General purpose I/O |
| Chân 75 | VSS — Ground |
| Chân 76 | VDD — Supply voltage |
| Chân 77 | RG10 — General purpose I/O |
| Chân 78 | RG11 — General purpose I/O |
| Chân 79 | RG0 — General purpose I/O |
| Chân 80 | RG1 — General purpose I/O |
| Chân 81 | RC12 — General purpose I/O |
| Chân 82 | RC11 — General purpose I/O |
| Chân 83 | RC10 — General purpose I/O |
| Chân 84 | RC9 — General purpose I/O |
| Chân 85 | VSS — Ground |
| Chân 86 | VDD — Supply voltage |
| Chân 87 | RC8 — General purpose I/O |
| Chân 88 | RC7 — General purpose I/O |
| Chân 89 | RC6 — General purpose I/O |
| Chân 90 | RC5 — General purpose I/O |
| Chân 91 | RB15 — General purpose I/O |
| Chân 92 | RB14 — General purpose I/O |
| Chân 93 | RB13 — General purpose I/O |
| Chân 94 | RB12 — General purpose I/O |
| Chân 95 | RB11 — General purpose I/O |
| Chân 96 | RB10 — General purpose I/O |
| Chân 97 | VSS — Ground |
| Chân 98 | VDD — Supply voltage |
| Chân 99 | RB9 — General purpose I/O |
| Chân 100 | RB8 — General purpose I/O |
| Chân 101 | RE0 — General purpose I/O |
| Chân 102 | RE1 — General purpose I/O |
| Chân 103 | RE2 — General purpose I/O |
| Chân 104 | RE3 — General purpose I/O |
| Chân 105 | RE4 — General purpose I/O |
| Chân 106 | RE5 — General purpose I/O |
| Chân 107 | RE6 — General purpose I/O |
| Chân 108 | RE7 — General purpose I/O |
| Chân 109 | RG2 — General purpose I/O |
| Chân 110 | RG3 — General purpose I/O |
| Chân 111 | VSS — Ground |
| Chân 112 | VDD — Supply voltage |
| Chân 113 | RB5 — General purpose I/O |
| Chân 114 | RB4 — General purpose I/O |
| Chân 115 | RB3 — General purpose I/O |
| Chân 116 | RB2 — General purpose I/O |
| Chân 117 | RB1 — General purpose I/O |
| Chân 118 | RB0 — General purpose I/O |
| Chân 119 | RA10 — General purpose I/O |
| Chân 120 | RA11 — General purpose I/O |
| Chân 121 | RA12 — General purpose I/O |
| Chân 122 | RA13 — General purpose I/O |
| Chân 123 | RA14 — General purpose I/O |
| Chân 124 | RA15 — General purpose I/O |
| Chân 125 | VSS — Ground |
| Chân 126 | VDD — Supply voltage |
| Chân 127 | OSC1 — Crystal oscillator input |
| Chân 128 | OSC2 — Crystal oscillator output |
| Chân 129 | SOSCO — Secondary oscillator output for RTCC |
| Chân 130 | SOSCI — Secondary oscillator input for RTCC |
| Chân 131 | VDDPLL — PLL supply voltage |
| Chân 132 | VSSPLL — PLL ground |
| Chân 133 | VCAP — External capacitor for internal voltage regulator |
| Chân 134 | VUSB3V3 — USB 3.3V supply |
| Chân 135 | VUSB — USB analog supply |
| Chân 136 | D+ — USB D+ data line |
| Chân 137 | D- — USB D- data line |
| Chân 138 | VBUS — USB VBUS sense |
| Chân 139 | MCLR — Master clear (active-low) |
| Chân 140 | RG15 — General purpose I/O |
| Chân 141 | RB8 — General purpose I/O |
| Chân 142 | RB9 — General purpose I/O |
| Chân 143 | RB10 — General purpose I/O |
| Chân 144 | RB11 — General purpose I/O |
Ứng dụng tiêu biểu
PIC32MZ1024EFF144-E/PL phù hợp cho 6 Áp dụngs: Industrial IoT Gateway with Ethernet and CAN, Automotive Infotainment HMI Controller, Motor Control Field-Oriented Control (FOC) Drive, Audio Processing and Graphics HMI, Point-of-Sale Terminal with Secure Boot, Smart Energy Meter with Power Line Communication.
Industrial IoT Gateway with Ethernet and CAN
The PIC32MZ1024EFF144-E/PL fits industrial IoT gateways because it integrates a 10/100 Ethernet MAC and dual CAN 2.0B controllers alongside the 200 MHz MIPS core with hardware crypto. This eliminates the need for an external PHY or MCU-to-CAN bridge. The 1 MB dual-panel Live-Update Flash allows firmware OTA updates without halting the gateway, while -40C to +125C operation suits outdoor cabinets. The FPU accelerates TLS handshake processing for cloud-connected PLCs and Modbus TCP stacks.
Được đề xuất
Automotive Infotainment HMI Controller
The PIC32MZ1024EFF144-E/PL drives automotive HMI panels because the integrated FPU and DSP extensions process TFT graphics and audio codecs at 200 MHz without external DSP. The HS USB 2.0 with integrated PHY connects to smartphone projection stacks (CarPlay, Android Auto), while CAN interfaces to vehicle body networks. The 144-LQFP exposes the maximum I/O count needed for touch sensing, backlight PWM, and display parallel interface. Hardware crypto enables secure boot.
Được đề xuất
Motor Control Field-Oriented Control (FOC) Drive
The PIC32MZ1024EFF144-E/PL is ideal for field-oriented control motor drives because the MIPS M-class core with FPU executes FOC algorithms at 200 MHz within a single PWM cycle. The 12-bit 18 MSPS ADC samples phase currents at high PWM rates (20+ kHz) without bottleneck. The dual-panel Flash supports field firmware updates, and CAN interfaces to industrial servo networks. The 144-LQFP package handles the multiple PWM channels and encoder inputs.
Được đề xuất
Audio Processing and Graphics HMI
The PIC32MZ1024EFF144-E/PL powers graphics HMI panels and audio processing because the 200 MHz core with DSP extensions decodes audio codecs (MP3, AAC, Opus) and renders TFT graphics simultaneously. The SQI interface attaches high-speed external Flash for graphics assets and audio sample libraries. The integrated FPU accelerates FFT for audio EQ and noise-cancellation algorithms, while Ethernet streams networked audio. The 144-LQFP exposes all needed display and audio I/O pins.
Được đề xuất
Point-of-Sale Terminal with Secure Boot
The PIC32MZ1024EFF144-E/PL suits POS terminals because the EFF suffix includes hardware AES/DES/SHA accelerators for fast secure-boot validation and PCI-PTS encryption of cardholder data. The HS USB connects to PIN pads and card readers, Ethernet connects to payment networks, and the FPU accelerates RSA key exchanges. The 1 MB Flash holds POS application code and crypto libraries. The -E temperature grade handles outdoor kiosk deployments.
Được đề xuất
Smart Energy Meter with Power Line Communication
The PIC32MZ1024EFF144-E/PL drives smart energy meters because the 12-bit 18 MSPS ADC samples current and voltage waveforms for accurate Class-0.5 power calculations, while the FPU runs DFT/FFT for harmonic analysis. The dual-panel Flash supports remote firmware updates mandated by utility regulations. The 200 MHz core handles DLMS/COSEM protocol stacks, and CAN interfaces to concentrators. Hardware crypto secures AMI communications against tampering.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC32MZ1024EFF144-E/PL — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC32MZ1024EFF144-I/PL | PIC32MZ1024EFF144T-E/PL | PIC32MZ1024EFE144-I/PL | PIC32MZ1024EFE144-E/PH | PIC32MZ0512EFF144-E/PL | PIC32MZ1024EFF144-E/JWX |
|---|---|---|---|---|---|---|---|
| Package | 144-LQFP (20x20 mm) | 144-LQFP - same | 144-LQFP - same | 144-LQFP - same | 144-LQFP - same | 144-LQFP - same | 144-LQFP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 1 MB | 1 MB | 1 MB | 1 MB | 1 MB | 512 KB | 1 MB |
| SRAM | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 128 KB | 256 KB |
| Hardware Crypto | Yes (AES/DES/SHA) | Yes | Yes | No (EFE variant) | No (EFE variant) | Yes | Yes |
| Temperature Range | -40C to +125C (E grade) | -40C to +85C (I grade) | -40C to +125C | -40C to +85C | -40C to +125C | -40C to +125C | -40C to +125C |
| Core Frequency | 200 MHz | 200 MHz | 200 MHz | 200 MHz | 200 MHz | 200 MHz | 200 MHz |
| FPU | Yes (IEEE 754) | Yes | Yes | Yes | Yes | Yes | Yes |
| Ethernet MAC | 10/100 with MII/RMII | 10/100 with MII/RMII | 10/100 with MII/RMII | 10/100 with MII/RMII | 10/100 with MII/RMII | 10/100 with MII/RMII | 10/100 with MII/RMII |
Bảo phân biệt quan trọng
- Hardware crypto accelerator (AES/DES/SHA/HMAC) (vsPIC32MZ1024EFE144-I/PL)
- Extended industrial temperature grade -40C to +125C (vsPIC32MZ1024EFF144-I/PL)
- Dual-panel Live-Update Flash for fail-safe OTA (vsPIC32MX795F512L-80I/PT)
Ghi chú thiết kế
The PIC32MZ1024EFF144-E/PL requires careful supply decoupling: 100 nF ceramic on each VDD pin, 10 uF bulk, plus 1 uF and 100 nF on AVDD and VDDPLL. The VCAP pin (133) MUST have a 1 uF to 10 uF low-ESR ceramic capacitor; without it the internal 1.8V LDO will not regulate and the device will fail to start. Estimated total supply current is approximately 80-100 mA at 200 MHz with all peripherals active; design the 3.3V rail for at least 200 mA headroom.
Configure unused I/O pins as outputs driven low (not inputs floating) to avoid excessive current draw from floating CMOS inputs. The 144-LQFP package exposes all 120+ I/O pins and most designs leave several unused; floating inputs can cause 50-100 uA per pin. Refer to the Microchip PIC32MZ EF Family datasheet Section 42 for the specific recommended biasing and JTAG disable configuration. The MCLR pin must NEVER be left floating - always use a pull-up resistor.
At 200 MHz with all peripherals active, the PIC32MZ1024EFF144-E/PL dissipates approximately 350-400 mW typical and up to 700 mW peak (estimated based on typical 1.8V core current and IO loading). The 144-LQFP has theta_JA of approximately 45 C/W on a standard 4-layer JEDEC test board, giving a junction-to-ambient rise of 16-32 C above ambient at typical power. For continuous 125C operation ensure the ambient plus thermal rise stays below the 125C junction limit.
Place the 12 MHz primary crystal within 5 mm of OSC1/OSC2 pins with short, symmetric traces and a guard ring tied to ground. The SQI signals (SQICS, SQISCK, SQID0-SQID3) are high-speed (80+ MHz) and require matched-length traces within 25 mil; reference the Microchip SQI PCB layout application note. Keep the USB differential pair (D+/D-) to 90 ohm differential impedance and route them isolated from analog signals to maintain HS USB compliance.
Thông tin tuân thủ
RoHS compliant per Microchip product page. -E suffix is industrial extended temperature, not AEC-Q100 qualified - for AEC-Q100 automotive qualified PIC32 options see PIC32MX/MZ automotive-grade part numbers.