PIC32MZ2048ECG064-I/PT - 200MHz 2MB Flash MCU w/ Ethernet | Microchip
MPN: PIC32MZ2048ECG064-I/PT ✗ Cuối đờiPIC32MZ2048ECG064-I/PT Tóm tắt
An MCU (microcontroller unit) is a single-chip processor that integrates a CPU core, program and data memory, and a rich set of peripherals (ADC, timers, communication controllers) onto one die. Within the taxonomy microcontroller -> 32-bit MCU -> MIPS32 MCU -> PIC32MZ family -> embedded connectivity family, the PIC32MZ EC line is the higher-tier MIPS32 microAptiv part that sits between the cost-optimized PIC32MX line and the Floating Point Unit (FPU) PIC32MZ EF family. Understanding this hierarchy helps engineers locate firmware libraries (MPLAB Harmony), development boards, and datasheet documents.
Key features include 2 MB of live-update Flash with an additional 160 KB of boot Flash, microMIPS mode for up to 35% smaller code size, a DSP-enhanced core with four 64-bit accumulators and single-cycle MAC, and a hardware crypto engine. The 64-pin TQFP exposes USB, 10/100 Ethernet MAC, SQI, CAN, six UART, four SPI, five I2C, PMP, and a 24-channel 10-bit ADC. The EC suffix denotes the Embedded Connectivity (no FPU) sub-family.
Typical applications include industrial Ethernet gateways, networked HVAC controllers, USB peripherals, SQI Flash expansion, motor-control front-ends, and audio/graphics interfaces. The wide peripheral mix reduces external chip count for connected IoT designs.
Design with the datasheet's recommended 2.2V-3.6V decoupling scheme (4.7uF + 0.1uF per VDD pin pair), respect trace-length matching on Ethernet MII/RMII, and use the datasheet's trace-length matching on USB DP/DM. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho PIC32MZ2048ECG064-I/PT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC32MZ2048ECG064-I/PT (cùng hình factor và footprint) — khác nhau ở ADC, MSL Level, Package, Core Architecture, Ethernet.
PIC32MZ2048EFG064-I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MZ2048ECG064-I/PT Tỷ lệ tối đa & tính chất điện
| Core Architecture | MIPS32 microAptiv (32-bit RISC) |
| Core Family | PIC32MZ Embedded Connectivity (EC) family |
| Maximum CPU Clock | 200 MHz |
| Instruction Set | MIPS32 + microMIPS mode |
| Program Flash | 2 MB (2M x 8) |
| Boot Flash | 160 KB |
| SRAM | 512 KB |
| Operating Voltage | 2.2 V to 3.6 V |
| Nhiệt độ hoạt động | -40C to +85C (industrial) |
| ADC | 10-bit, 24 channels |
| Hộp | 64-pin TQFP (PT), 10x10 mm |
| Kiểu lắp đặt | Surface Mount |
| On-chip Peripherals | Ethernet MAC, USB 2.0 HS, SQI, CAN, RTCC, 6x UART, 4x SPI, 5x I2C, PMP, I2S |
| DMA Channels | 8 |
| Trạng thái RoHS | Compliant |
| Cấp MSL | 3 (168 hours) |
| Lead-Free | Yes |
Cấu hình chân PIC32MZ2048ECG064-I/PT
| Chân 1 | SDA1/RA14 — I2C1 data / GPIO RA14 |
| Chân 2 | SCL1/RA15 — I2C1 clock / GPIO RA15 |
| Chân 3 | AN33/RB0 — Analog input 33 / GPIO RB0 |
| Chân 4 | AN34/RB1 — Analog input 34 / GPIO RB1 |
| Chân 5 | AN35/RB2 — Analog input 35 / GPIO RB2 |
| Chân 6 | AN36/RB3 — Analog input 36 / GPIO RB3 |
| Chân 7 | AN37/RB4 — Analog input 37 / GPIO RB4 |
| Chân 8 | AN38/RB5 — Analog input 38 / GPIO RB5 |
| Chân 9 | AN39/RB6 — Analog input 39 / GPIO RB6 |
| Chân 10 | AN40/RB7 — Analog input 40 / GPIO RB7 |
| Chân 11 | AN41/RB8 — Analog input 41 / GPIO RB8 |
| Chân 12 | AN42/RB9 — Analog input 42 / GPIO RB9 |
| Chân 13 | VSS — Ground |
| Chân 14 | VDD — Core supply (3.3V) |
| Chân 15 | AN0/RA0 — Analog input 0 / GPIO RA0 |
| Chân 16 | AN1/RA1 — Analog input 1 / GPIO RA1 |
| Chân 17 | AN2/RA2 — Analog input 2 / GPIO RA2 |
| Chân 18 | AN3/RA3 — Analog input 3 / GPIO RA3 |
| Chân 19 | AN4/RA4 — Analog input 4 / GPIO RA4 |
| Chân 20 | AN5/RA5 — Analog input 5 / GPIO RA5 |
| Chân 21 | VSS — Ground |
| Chân 22 | VDD — Core supply (3.3V) |
| Chân 23 | AN8/RB14 — Analog input 8 / GPIO RB14 |
| Chân 24 | AN9/RB15 — Analog input 9 / GPIO RB15 |
| Chân 25 | AN10/RC1 — Analog input 10 / GPIO RC1 |
| Chân 26 | AN11/RC2 — Analog input 11 / GPIO RC2 |
| Chân 27 | AN12/RC3 — Analog input 12 / GPIO RC3 |
| Chân 28 | AN13/RC4 — Analog input 13 / GPIO RC4 |
| Chân 29 | VDD — Core supply (3.3V) |
| Chân 30 | VSS — Ground |
| Chân 31 | OSC1/RC12 — Crystal oscillator input / GPIO RC12 |
| Chân 32 | OSC2/RC15 — Crystal oscillator output / GPIO RC15 |
| Chân 33 | SOSC1/RPC0 — Secondary oscillator input |
| Chân 34 | SOSCO/RPC1 — Secondary oscillator output |
| Chân 35 | VDD — Core supply (3.3V) |
| Chân 36 | VSS — Ground |
| Chân 37 | TCK/RPA0 — JTAG test clock |
| Chân 38 | TDO/RPA1 — JTAG test data out |
| Chân 39 | TDI/RPA2 — JTAG test data in |
| Chân 40 | TMS/RPA3 — JTAG test mode select |
| Chân 41 | TRST/RPA4 — JTAG test reset |
| Chân 42 | RTCC/RPA8 — Real-time clock alarm output |
| Chân 43 | DM/RPA9 — USB DM line |
| Chân 44 | DP/RPA10 — USB DP line |
| Chân 45 | VBUS/RPA11 — USB VBUS detect |
| Chân 46 | VUSB — USB transceiver supply (3.3V) |
| Chân 47 | AVDD — Analog supply (3.3V) |
| Chân 48 | AVSS — Analog ground |
| Chân 49 | AEREF/RPA7 — ADC reference voltage |
| Chân 50 | RD0 — GPIO RD0 / ETXD0 |
| Chân 51 | RD1 — GPIO RD1 / ETXD1 |
| Chân 52 | RD2 — GPIO RD2 / ETXD2 |
| Chân 53 | RD3 — GPIO RD3 / ETXD3 |
| Chân 54 | RD4 — GPIO RD4 / ECRS_DV |
| Chân 55 | RD5 — GPIO RD5 / ERX0 |
| Chân 56 | RD6 — GPIO RD6 / ERX1 |
| Chân 57 | RD7 — GPIO RD7 / ERXER |
| Chân 58 | RD8 — GPIO RD8 / ETXEN |
| Chân 59 | RD9 — GPIO RD9 / EMDIO |
| Chân 60 | RD10 — GPIO RD10 / EMDC |
| Chân 61 | RD11 — GPIO RD11 |
| Chân 62 | RD12 — GPIO RD12 |
| Chân 63 | RD13 — GPIO RD13 |
| Chân 64 | RD14 — GPIO RD14 |
Ứng dụng tiêu biểu
PIC32MZ2048ECG064-I/PT phù hợp cho 6 Áp dụngs: Industrial Ethernet Gateway, USB Hi-Speed Peripheral Controller, IoT Connected Sensor Node, Motor Control Front-End, Audio Interface Processor, Graphical HMI Controller.
Industrial Ethernet Gateway
The PIC32MZ2048ECG064-I/PT fits industrial Ethernet gateway designs because its on-chip 10/100 Ethernet MAC, MII/RMII interface, 2 MB Flash, and 512 KB SRAM can run TCP/IP stacks such as Microchip's MLA or third-party lwIP. The 200 MHz MIPS32 core handles routing, protocol translation (Modbus TCP, EtherNet/IP), and TLS handshakes without an external network processor. Industrial -40C to +85C temperature rating lets the part operate in unshielded factory cabinets.
Được đề xuất
USB Hi-Speed Peripheral Controller
The PIC32MZ2048ECG064-I/PT fits USB High-Speed peripheral designs because it integrates a USB 2.0 HS controller with on-chip transceiver that supports host, device, and OTG roles. The 512 KB SRAM is sufficient for HID, CDC, and bulk-endpoint buffers, while the 2 MB Flash holds USB class firmware stacks. The 200 MHz MIPS32 core handles enumeration and bulk transfers at up to 480 Mbps.
Được đề xuất
IoT Connected Sensor Node
The PIC32MZ2048ECG064-I/PT fits IoT connected sensor nodes because its on-chip Ethernet MAC, SQI for external Flash expansion, and 24-channel 10-bit ADC can aggregate multiple sensor inputs while publishing them over Ethernet or USB. The microMIPS mode reduces code size by up to 35%, allowing larger firmware images in the 2 MB Flash. Low-power Sleep and Idle modes drop quiescent current for battery-friendly operation.
Được đề xuất
Motor Control Front-End
The PIC32MZ2048ECG064-I/PT fits motor-control front-end applications because its 200 MHz MIPS32 core plus DSP extensions (four 64-bit accumulators, single-cycle MAC) can run Field-Oriented Control loops in real time. Six UART channels and CAN handle encoder, resolver, and inverter feedback. PWM peripherals (OC, MCCP/SCCP) drive 3-phase inverter switches with hardware dead-band generation.
Được đề xuất
Audio Interface Processor
The PIC32MZ2048ECG064-I/PT fits audio interface processor designs because it integrates I2S and PMP peripherals, plus enough MIPS to run USB Audio Class 2.0 stacks at 192 kHz sample rates. The 512 KB SRAM acts as an audio sample buffer without external memory. Ethernet MAC can also carry Dante or AVB audio streams in professional installations.
Được đề xuất
Graphical HMI Controller
The PIC32MZ2048ECG064-I/PT fits graphical HMI controller designs because the PMP peripheral drives external TFT displays up to 16-bit parallel, while SQI provides high-speed access to external Flash for graphics assets. The 200 MHz CPU handles LVGL/PEG graphics libraries and capacitive-touch scanning. Ethernet MAC enables remote HMI web configuration over HTTP.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC32MZ2048ECG064-I/PT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC32MZ2048EFG064-I/PT | PIC32MZ2048ECG064-I/MR | PIC32MZ1024ECG064-I/PT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP (10x10 mm) | 64-pin TQFP - same | 64-pin QFN (MR) - differs | 64-pin TQFP - same |
| Core Family | PIC32MZ EC (no FPU) | PIC32MZ EF (FPU) | PIC32MZ EC - same | PIC32MZ EC - same |
| Maximum CPU Clock | 200 MHz | 252 MHz (+26%) | 200 MHz - same | 200 MHz - same |
| Program Flash | 2 MB | 2 MB - same | 2 MB - same | 1 MB (-50%) |
| SRAM | 512 KB | 512 KB - same | 512 KB - same | 512 KB - same |
| Ethernet MAC | 10/100 (MII/RMII) | 10/100 - same | 10/100 - same | 10/100 - same |
| USB 2.0 | High-Speed (480 Mbps) | High-Speed - same | High-Speed - same | High-Speed - same |
| FPU | No | Yes | No - same | No - same |
| Lifecycle Status | NRND | Active | NRND | NRND |
Bảo phân biệt quan trọng
- Embedded Connectivity sub-family with on-chip 10/100 Ethernet MAC + USB HS (vsPIC32MX795F512H-80V/PT)
- MIPS32 microAptiv core with microMIPS code compression (vsPIC32MX795F512H-80V/PT)
- Pin-compatible upgrade path to PIC32MZ EF family with FPU (vsPIC32MX795F512H-80V/PT)
Ghi chú thiết kế
PIC32MZ2048ECG064-I/PT operates from a single 2.2-3.6 V rail. Per the Microchip datasheet, decouple every VDD pin with a 0.1 uF X7R ceramic placed within 5 mm, and add one bulk 4.7 uF ceramic per VDDIO pair. AVDD needs its own 10 ohm ferrite + 0.1 uF + 4.7 uF LC filter to keep ADC noise below 1 LSB. VBAT and VUSB both require their own dedicated 3.3 V regulators when USB HS or RTCC backup are used.
Route USB DP/DM as a 90-ohm differential pair with trace-length matching under 1 mm. Route Ethernet MII signals as 50-ohm single-ended traces kept under 50 mm with continuous ground reference. Place the 24 MHz crystal within 8 mm of the OSC1/OSC2 pins and guard it with a ground ring. Maintain a 4-layer stack-up with a dedicated ground plane under the TQFP footprint.
Avoid using pins RA14/RA15 as GPIO when I2C1 is enabled - they are 5V-tolerant only with explicit open-drain configuration. Do not exceed the 200 MHz maximum CPU clock even when the EF family supports 252 MHz. The 2 MB Flash supports live updates only when configured in Dual-Bank mode; Single-Panel mode disables live update. Always unlock the IOLOCK configuration register before changing PPS pin mappings.
Estimated: at full 200 MHz operation with all peripherals active and USB HS enabled, the PIC32MZ2048ECG064-I/PT draws approximately 110 mA from the 3.3 V rail, dissipating about 0.36 W. The TQFP-64 thermal resistance (theta_JA) is approximately 39 C/W per the Microchip package drawing, resulting in a 14 C junction rise above ambient at room temperature - well within the 85 C industrial limit.
Thông tin tuân thủ
RoHS compliant per Microchip product page. Industrial -40C to +85C temperature range. Not AEC-Q100 qualified - see PIC32MZ automotive variants for automotive applications.
