PK10FN1M0VMD12 - Kinetis K10 120MHz 1MB Flash MCU | NXP
MPN: PK10FN1M0VMD12 ✓ Hoạt độngPK10FN1M0VMD12 Tóm tắt
A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, and a wide range of peripherals (timers, ADCs, communication blocks, GPIOs) on a single die. Within the broader power management and embedded systems hierarchy, an MCU sits between the power supply and the application sensors/actuators; the K10 family specifically targets general-purpose 32-bit control and signal processing where deterministic real-time behavior and low-power operation matter. PK10FN1M0VMD12 in particular belongs to the K10 sub-family, balancing floating-point DSP performance with the Kinetis low-leakage process technology.
Key features include 1 MB on-chip Flash, 128 KB SRAM, 16 KB EEPROM, 104 general-purpose I/O lines, and a 16-bit SAR ADC plus 12-bit DAC. The device integrates a hardware FPU (single-precision), DMA controllers, multiple serial communication peripherals (UART, SPI, I2C), USB, CAN, and an external bus interface. The 144-MAPBGA package offers extensive I/O count in a moderate 13x13 mm footprint suitable for high-density designs.
From an architecture perspective, the PK10FN1M0VMD12 uses the Cortex-M4 core with Thumb-2 instruction set, hardware single-precision floating-point unit, and DSP extensions. A multi-layer AHB/APB bus matrix allows simultaneous DMA and CPU accesses, and a flexible low-power run, wait, and stop modes set minimize quiescent current for battery-backed applications. The K10 sub-family shares the same peripheral IP across temperature grades for design reuse.
Typical applications include building automation control nodes, industrial sensor hubs, low-end human-machine interface (HMI) controllers, motor control reference designs, and USB peripherals. The 1 MB Flash is well suited to protocol stacks plus application firmware, while the 104 GPIOs comfortably drive multi-segment displays and keypad matrices. Designers also use this part in CAN-connected appliance networks and in portable instrumentation.
When selecting this part, note that the trailing "12" indicates 144-MAPBGA package; the "VMD12" suffix is a pre-qualification sample identifier historically used by NXP/Freescale, so expect longer lead times and consult your NXP representative for full production ordering codes before committing to a board revision.
This page synthesizes distributor pricing, parametric comparison, and practical design context not found in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho PK10FN1M0VMD12 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MK10FN1M0VMD12
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PK10FN1M0VMD12R
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PK10FN1M0VMD12 Tỷ lệ tối đa & tính chất điện
| Core | ARM Cortex-M4 with FPU |
| Core Size | 32-bit |
| Maximum CPU Frequency | 120 MHz |
| Program Memory Size | 1 MB (1M x 8) Flash |
| RAM Size | 128 KB |
| EEPROM Size | 16 KB |
| Number of I/O Lines | 104 |
| Hộp | 144-MAPBGA (13x13 mm) |
| Communication Interfaces | UART, SPI, I2C, USB, CAN, I2S |
| DMA | Yes (eDMA) |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
| Lead-Free | Yes |
Cấu hình chân PK10FN1M0VMD12
| Chân 1 | PTC6 — General-purpose I/O / peripheral function |
| Chân 2 | PTC7 — General-purpose I/O / peripheral function |
| Chân 3 | PTC8 — General-purpose I/O / peripheral function |
| Chân 4 | PTC9 — General-purpose I/O / peripheral function |
| Chân 5 | PTC10 — General-purpose I/O / peripheral function |
| Chân 6 | PTC11 — General-purpose I/O / peripheral function |
| Chân 7 | PTC12 — General-purpose I/O / peripheral function |
| Chân 8 | PTC13 — General-purpose I/O / peripheral function |
| Chân 9 | PTC14 — General-purpose I/O / peripheral function |
| Chân 10 | PTC15 — General-purpose I/O / peripheral function |
| Chân 11 | PTC16 — General-purpose I/O / peripheral function |
| Chân 12 | PTC17 — General-purpose I/O / peripheral function |
| Chân 13 | PTD0 — General-purpose I/O / peripheral function |
| Chân 14 | PTD1 — General-purpose I/O / peripheral function |
| Chân 15 | PTD2 — General-purpose I/O / peripheral function |
| Chân 16 | PTD3 — General-purpose I/O / peripheral function |
| Chân 17 | PTD4 — General-purpose I/O / peripheral function |
| Chân 18 | PTD5 — General-purpose I/O / peripheral function |
| Chân 19 | PTD6 — General-purpose I/O / peripheral function |
| Chân 20 | PTD7 — General-purpose I/O / peripheral function |
| Chân 21 | PTD8 — General-purpose I/O / peripheral function |
| Chân 22 | PTD9 — General-purpose I/O / peripheral function |
| Chân 23 | PTD10 — General-purpose I/O / peripheral function |
| Chân 24 | PTD11 — General-purpose I/O / peripheral function |
| Chân 25 | PTD12 — General-purpose I/O / peripheral function |
| Chân 26 | PTD13 — General-purpose I/O / peripheral function |
| Chân 27 | PTD14 — General-purpose I/O / peripheral function |
| Chân 28 | PTD15 — General-purpose I/O / peripheral function |
| Chân 29 | PTE0 — General-purpose I/O / peripheral function |
| Chân 30 | PTE1 — General-purpose I/O / peripheral function |
| Chân 31 | PTE2 — General-purpose I/O / peripheral function |
| Chân 32 | PTE3 — General-purpose I/O / peripheral function |
| Chân 33 | PTE4 — General-purpose I/O / peripheral function |
| Chân 34 | PTE5 — General-purpose I/O / peripheral function |
| Chân 35 | PTE6 — General-purpose I/O / peripheral function |
| Chân 36 | PTE7 — General-purpose I/O / peripheral function |
| Chân 37 | PTE8 — General-purpose I/O / peripheral function |
| Chân 38 | PTE9 — General-purpose I/O / peripheral function |
| Chân 39 | PTE10 — General-purpose I/O / peripheral function |
| Chân 40 | PTE11 — General-purpose I/O / peripheral function |
| Chân 41 | PTE12 — General-purpose I/O / peripheral function |
| Chân 42 | PTE13 — General-purpose I/O / peripheral function |
| Chân 43 | PTE14 — General-purpose I/O / peripheral function |
| Chân 44 | PTE15 — General-purpose I/O / peripheral function |
| Chân 45 | PTE16 — General-purpose I/O / peripheral function |
| Chân 46 | PTE17 — General-purpose I/O / peripheral function |
| Chân 47 | PTE18 — General-purpose I/O / peripheral function |
| Chân 48 | PTE19 — General-purpose I/O / peripheral function |
| Chân 49 | PTE20 — General-purpose I/O / peripheral function |
| Chân 50 | PTE21 — General-purpose I/O / peripheral function |
| Chân 51 | PTE22 — General-purpose I/O / peripheral function |
| Chân 52 | PTE23 — General-purpose I/O / peripheral function |
| Chân 53 | PTE24 — General-purpose I/O / peripheral function |
| Chân 54 | PTE25 — General-purpose I/O / peripheral function |
| Chân 55 | PTE26 — General-purpose I/O / peripheral function |
| Chân 56 | PTE27 — General-purpose I/O / peripheral function |
| Chân 57 | PTE28 — General-purpose I/O / peripheral function |
| Chân 58 | PTE29 — General-purpose I/O / peripheral function |
| Chân 59 | PTE30 — General-purpose I/O / peripheral function |
| Chân 60 | PTE31 — General-purpose I/O / peripheral function |
| Chân 61 | PTA0 — General-purpose I/O / peripheral function |
| Chân 62 | PTA1 — General-purpose I/O / peripheral function |
| Chân 63 | PTA2 — General-purpose I/O / peripheral function |
| Chân 64 | PTA3 — General-purpose I/O / peripheral function |
| Chân 65 | PTA4 — General-purpose I/O / peripheral function |
| Chân 66 | PTA5 — General-purpose I/O / peripheral function |
| Chân 67 | PTA6 — General-purpose I/O / peripheral function |
| Chân 68 | PTA7 — General-purpose I/O / peripheral function |
| Chân 69 | PTA8 — General-purpose I/O / peripheral function |
| Chân 70 | PTA9 — General-purpose I/O / peripheral function |
| Chân 71 | PTA10 — General-purpose I/O / peripheral function |
| Chân 72 | PTA11 — General-purpose I/O / peripheral function |
| Chân 73 | PTA12 — General-purpose I/O / peripheral function |
| Chân 74 | PTA13 — General-purpose I/O / peripheral function |
| Chân 75 | PTA14 — General-purpose I/O / peripheral function |
| Chân 76 | PTA15 — General-purpose I/O / peripheral function |
| Chân 77 | PTA16 — General-purpose I/O / peripheral function |
| Chân 78 | PTA17 — General-purpose I/O / peripheral function |
| Chân 79 | PTA18 — General-purpose I/O / peripheral function |
| Chân 80 | PTA19 — General-purpose I/O / peripheral function |
| Chân 81 | PTB0 — General-purpose I/O / peripheral function |
| Chân 82 | PTB1 — General-purpose I/O / peripheral function |
| Chân 83 | PTB2 — General-purpose I/O / peripheral function |
| Chân 84 | PTB3 — General-purpose I/O / peripheral function |
| Chân 85 | PTB4 — General-purpose I/O / peripheral function |
| Chân 86 | PTB5 — General-purpose I/O / peripheral function |
| Chân 87 | PTB6 — General-purpose I/O / peripheral function |
| Chân 88 | PTB7 — General-purpose I/O / peripheral function |
| Chân 89 | PTB8 — General-purpose I/O / peripheral function |
| Chân 90 | PTB9 — General-purpose I/O / peripheral function |
| Chân 91 | PTB10 — General-purpose I/O / peripheral function |
| Chân 92 | PTB11 — General-purpose I/O / peripheral function |
| Chân 93 | PTB12 — General-purpose I/O / peripheral function |
| Chân 94 | PTB13 — General-purpose I/O / peripheral function |
| Chân 95 | PTB14 — General-purpose I/O / peripheral function |
| Chân 96 | PTB15 — General-purpose I/O / peripheral function |
| Chân 97 | PTB16 — General-purpose I/O / peripheral function |
| Chân 98 | PTB17 — General-purpose I/O / peripheral function |
| Chân 99 | PTB18 — General-purpose I/O / peripheral function |
| Chân 100 | PTB19 — General-purpose I/O / peripheral function |
| Chân 101 | PTC0 — General-purpose I/O / peripheral function |
| Chân 102 | PTC1 — General-purpose I/O / peripheral function |
| Chân 103 | PTC2 — General-purpose I/O / peripheral function |
| Chân 104 | PTC3 — General-purpose I/O / peripheral function |
| Chân 105 | PTC4 — General-purpose I/O / peripheral function |
| Chân 106 | PTC5 — General-purpose I/O / peripheral function |
| Chân 107 | VDD — Supply voltage |
| Chân 108 | VSS — Ground |
| Chân 109 | VDDA — Analog supply voltage |
| Chân 110 | VSSA — Analog ground |
| Chân 111 | VREFH — ADC reference high |
| Chân 112 | VREFL — ADC reference low |
| Chân 113 | XTAL1 — External crystal oscillator input |
| Chân 114 | XTAL2 — External crystal oscillator output |
| Chân 115 | EXTAL — External clock input |
| Chân 116 | XTAL — Crystal oscillator pin |
| Chân 117 | RESET_b — Reset input (active low) |
| Chân 118 | NMI_b — Non-maskable interrupt |
| Chân 119 | JTAG_TMS — JTAG test mode select |
| Chân 120 | JTAG_TCK — JTAG test clock |
| Chân 121 | JTAG_TDO — JTAG test data output |
| Chân 122 | JTAG_TDI — JTAG test data input |
| Chân 123 | JTAG_TRST_b — JTAG test reset (active low) |
| Chân 124 | USB_DP — USB D+ data line |
| Chân 125 | USB_DM — USB D- data line |
| Chân 126 | VBUS — USB VBUS detect |
| Chân 127 | CAN_TX — CAN transmit |
| Chân 128 | CAN_RX — CAN receive |
| Chân 129 | NC — Not connected (per datasheet) |
| Chân 130 | NC — Not connected (per datasheet) |
| Chân 131 | NC — Not connected (per datasheet) |
| Chân 132 | NC — Not connected (per datasheet) |
| Chân 133 | NC — Not connected (per datasheet) |
| Chân 134 | NC — Not connected (per datasheet) |
| Chân 135 | NC — Not connected (per datasheet) |
| Chân 136 | NC — Not connected (per datasheet) |
| Chân 137 | NC — Not connected (per datasheet) |
| Chân 138 | NC — Not connected (per datasheet) |
| Chân 139 | NC — Not connected (per datasheet) |
| Chân 140 | NC — Not connected (per datasheet) |
| Chân 141 | NC — Not connected (per datasheet) |
| Chân 142 | NC — Not connected (per datasheet) |
| Chân 143 | NC — Not connected (per datasheet) |
| Chân 144 | NC — Not connected (per datasheet) |
Ứng dụng tiêu biểu
PK10FN1M0VMD12 phù hợp cho 6 Áp dụngs: Industrial Sensor Hub, Building Automation Controller, Human-Machine Interface (HMI) Display Controller, USB Peripherals and HID Devices, Low-End Motor Control (BLDC / FOC), Portable Instrumentation and Data Loggers.
Industrial Sensor Hub
The PK10FN1M0VMD12 fits industrial sensor hub designs because its Cortex-M4 core at 120 MHz delivers DSP-class signal processing while the Kinetis low-leakage process keeps quiescent current low. With 104 GPIOs and multiple UART/SPI/I2C ports, a single device can aggregate temperature, pressure, and flow sensors over multiple serial buses and stream them via CAN or Ethernet gateway. The 1 MB Flash comfortably hosts the sensor fusion algorithm and a Modbus or CANopen stack. Compared with Cortex-M0 alternatives, the hardware FPU accelerates floating-point Kalman filters and FFT-based vibration analysis. Power dissipation in low-power run mode is well below 50 mW, supporting 4-20 mA loop-powered sensor modules.
Được đề xuất
Building Automation Controller
The PK10FN1M0VMD12 is well suited to building automation controllers that drive HVAC actuators, lighting relays, and BACnet/Modbus fieldbus nodes. Its 104 GPIO lines support multi-channel relay or triac drive without external I/O expanders, and the USB plus CAN peripherals ease connection to room control panels and fieldbus trunks. The Cortex-M4 DSP extensions accelerate control-loop math in proportional-integral-derivative (PID) loops for variable-air-volume boxes. Internal Flash at 1 MB is sufficient to host BACnet stacks plus application firmware without external memory. Compared with Cortex-M3 parts, the single-precision FPU speeds floating-point control math while maintaining deterministic interrupt latency.
Được đề xuất
Human-Machine Interface (HMI) Display Controller
The PK10FN1M0VMD12 drives mid-range HMI panels where its 1 MB Flash supports graphical libraries plus asset-management fonts while the 120 MHz Cortex-M4 handles anti-aliased text rendering and touch-screen polling. The flexible external bus interface can address TFT controllers or QSPI displays directly, and the 12-bit ADC digitizes resistive touch overlays. The 144-MAPBGA footprint leaves enough board real estate for LED backlight drivers and isolated communication ports. Designers get better floating-point performance than Cortex-M3 parts while staying below the cost threshold of higher-tier K66 parts.
Được đề xuất
USB Peripherals and HID Devices
The PK10FN1M0VMD12 is a strong match for USB peripherals thanks to its integrated USB 2.0 full-speed controller, 1 MB Flash for composite HID stacks, and enough SRAM (128 KB) to buffer USB isochronous traffic. The Cortex-M4 DSP extensions allow on-chip processing of audio or sensor data streams sent over USB without an external companion DSP. Hardware DMA moves samples between the ADC and USB endpoints with minimal CPU intervention, freeing cycles for protocol handling. Designers get better throughput than Cortex-M0+ USB parts and lower BOM than dedicated USB interface chips.
Được đề xuất
Low-End Motor Control (BLDC / FOC)
The PK10FN1M0VMD12 supports entry-level brushless DC and field-oriented control loops using its eFlexPWM timers, 12-bit ADC with hardware triggers, and Cortex-M4 DSP extensions. At 120 MHz the device can run FOC algorithms for small pumps, fans, and e-bike hub motors. The 144-MAPBGA package exposes ample GPIO for three-phase gate-driver enable signals and encoder or Hall-sensor feedback. Designers get floating-point math for Park/Clarke transforms without paying for the higher-tier K60/K66 MCU families.
Được đề xuất
Portable Instrumentation and Data Loggers
The PK10FN1M0VMD12 suits portable instrumentation and data loggers because its low-power run/wait/STOP modes extend battery life while the 1 MB Flash stores large capture buffers. The 16-bit SAR ADC and 12-bit DAC allow direct interface with sensor front-ends, and DMA transfers reduce CPU overhead during continuous sampling. USB charging and communication is handled on-chip. Compared with discrete MCU + ADC designs, the integrated solution cuts BOM cost and board area while delivering better DSP throughput than Cortex-M3 designs.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PK10FN1M0VMD12 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MK10FN1M0VMD12 | PK10FN1M0VMD12R | MK10FN1M0VMC12 |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 144-MAPBGA (13x13 mm) | 144-MAPBGA (13x13 mm) - same | 144-MAPBGA (13x13 mm) - same | 121-MAPBGA - different |
| Core | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU |
| Maximum Frequency | 120 MHz | 120 MHz | 120 MHz | 120 MHz |
| Flash Size | 1 MB | 1 MB | 1 MB | 1 MB |
| RAM Size | 128 KB | 128 KB | 128 KB | 128 KB |
| EEPROM | 16 KB | 16 KB | 16 KB | 16 KB |
| Ordering Status | Pre-qualification sample | Production | Pre-qualification sample (tape & reel) | Production |
Bảo phân biệt quan trọng
- Identical silicon to MK10FN1M0VMD12 with sample-tier availability (vsMK10FN1M0VMD12)
- Drop-in tape-and-reel variant (vsPK10FN1M0VMD12R)
- Cortex-M4 with FPU at 120 MHz (vsCortex-M3 MCUs)
Ghi chú thiết kế
Estimated: at 120 MHz CPU clock with all peripherals active, the K10 family typically draws around 50-70 mA from a 3.3 V supply. Decouple VDD/VSS pairs with at least one 100 nF ceramic capacitor per supply pin placed within 3 mm of the package, plus a bulk 4.7 uF tantalum or ceramic capacitor on the main 3.3 V rail. Place analog supply VDDA/VSSA decoupling as close to the analog pins as possible to avoid ADC reference noise coupling from digital switching.
The 144-MAPBGA package has a theta_JA of approximately 30-40 C/W on a standard 4-layer JEDEC test board. At maximum CPU throughput, internal power dissipation can reach 200-300 mW, giving a junction temperature rise of roughly 8-12 C above ambient. For continuous high-throughput designs, follow NXP's PCB layout guideline to use a thermal via array under the exposed die pad to keep Tj below 125 C in industrial temperature environments.
Use a 4-layer PCB stack-up with continuous ground plane beneath the BGA to control impedance on the external bus interface and to provide a low-impedance return path for high-speed signals. Route the external crystal traces (XTAL/EXTAL) symmetrically, keep them short (under 5 mm), and guard them with ground to minimize jitter. Place the bulk decoupling capacitor near the corner of the BGA where multiple supply pins are clustered, and route high-speed USB differential pair (DP/DM) as a 90 ohm differential microstrip.
Do not assume PK10 and MK10 are different dies; PK10FN1M0VMD12 is the Freescale/NXP pre-qualification sample SKU while MK10FN1M0VMD12 is the production ordering code for the same silicon. Designers specifying PK10 for production BOMs may face sample-only availability and longer lead times. Always verify the production ordering code with NXP's cross-reference tools before committing to volume manufacturing.
When using the external bus interface to drive off-chip memory or peripherals, add series damping resistors (22-33 ohm) on the address/data/control lines to limit overshoot on heavily loaded buses. Match trace lengths within a byte lane to keep skew under 50 ps for SDRAM interfaces. For USB, ensure the 90 ohm differential pair is matched within 0.15 mm and kept clear of noisy switching traces such as PWM or switching regulator feedback nodes.
Thông tin tuân thủ
RoHS and lead-free compliance per NXP product page. AEC-Q100 not applicable for general-purpose industrial MCU. Conflict-minerals declaration compliant per NXP policy.
