S912XEQ384J3VAL - 16-bit HCS12X MCU 384KB Flash 50MHz | NXP
MPN: S912XEQ384J3VAL ✓ Hoạt độngS912XEQ384J3VAL Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, volatile data memory, and a wide range of on-chip peripherals such as ADCs, timers and communication controllers. Within the broader semiconductor taxonomy, microcontrollers sit under microprocessors, which sit under digital ICs and ultimately integrated circuits. The S12X specifically extends the classic HCS12 instruction set with a richer addressing mode set and paged memory management, while the XGATE engine supplies a low-latency auxiliary execution path used by NXP for virtual peripherals that historically required external logic.
Key features of this part include CAN 2.0 controllers, SCI/SPI/IIC peripherals, 8-channel 16-bit Enhanced Capture Timer (ECT), Periodic Interrupt Timer (PIT), Real-Time Interrupt (RTI), and 12-bit ATD channels with 3 us conversion. The integrated voltage regulator operates from 1.8 V/2.8 V/5 V MCU rails, supporting automotive 12 V and 24 V battery systems after external regulation. The LQFP-112 footprint supports legacy automotive PCB tooled for Freescale S12X designs.
Typical applications include automotive body controllers, instrument clusters, HVAC control modules, and industrial CAN nodes that require ASIL-relevant firmware partitioning with on-chip supervisor/user separation. The XGATE allows deterministic handling of CAN and PWM without interrupting the S12X core, enabling tight PID control loops. The 12-bit ATD and 16-bit ECT provide simultaneous sampling and input capture needed for motor control and sensor interfacing.
When designing with the S912XEQ384J3VAL, decouple all four VDDX/VSSX pairs near the pins and route the XFC capacitor carefully per the datasheet; an undersized XFC cap causes POR faults at low temperature. The MCU must boot through BDM or via the secure serial bootloader unless an unsecure-mode development key is provisioned; plan toolchain selection early - CodeWarrior legacy projects must be rebuilt for CodeWarrior 5.x or migrated to S32 Design Studio.
Bộ thay thế dễ dàng lắp đặt cho S912XEQ384J3VAL — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với S912XEQ384J3VAL (cùng hình factor và footprint) — khác nhau ở Package, Mounting Type, Operating Temperature, Core, Timers.
S912XEQ384J3CAL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →S912XEQ384J3CALR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →S912XEG384J2CALR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →S912XEQ384F1VAL
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
S912XEQ512J2MAL
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →S912XET512J3MAG
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC9S12XEG128MAA
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MC9S12XEQ512CAG
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →S912XEQ384J3VAL Tỷ lệ tối đa & tính chất điện
| Core | S12X (HCS12X) 16-bit |
| Co-processor | XGATE peripheral engine |
| Maximum CPU Frequency | 50 MHz |
| Bus Speed | 25 MHz |
| Program Flash | 384 KB |
| Data Flash / EEPROM | FlexMemory (up to ~4 KB D-Flash + emulated EEPROM) |
| RAM | 16 KB |
| On-chip ADC | 12-bit ATD, ~3 us conversion |
| Timers | ECT (16-bit), PIT, RTI |
| Communication | CAN 2.0, SCI, SPI, IIC |
| Memory Protection | Memory Protection Unit (MPU), supervisor/user modes |
| Khoảng nhiệt độ hoạt động | -40C to +105C |
| Điện áp cung cấp | 1.8 V / 2.8 V / 5 V (internal regulator) |
| Hộp | 112-LQFP (20 x 20 mm) |
| Automotive Qualification | AEC-Q100 Grade 1 |
| Trạng thái RoHS | Compliant |
| Kiểu lắp đặt | Surface Mount (Tray per Arrow listing) |
Cấu hình chân S912XEQ384J3VAL
| Chân 1 | VSS1 — Ground reference 1 |
| Chân 2 | VDDR — Regulated supply for internal regulator |
| Chân 3 | VDDX1 — External supply 1 (5 V / 3.3 V) |
| Chân 4 | VSSX1 — External ground 1 |
| Chân 5 | VDDX2 — External supply 2 |
| Chân 6 | VSSX2 — External ground 2 |
| Chân 7 | PE0 — Port E bit 0 / CAN4TX (alternate) |
| Chân 8 | PE1 — Port E bit 1 / CAN4RX (alternate) |
| Chân 9 | PE2 — Port E bit 2 |
| Chân 10 | PE3 — Port E bit 3 |
| Chân 11 | PE4 — Port E bit 4 |
| Chân 12 | PE5 — Port E bit 5 |
| Chân 13 | PE6 — Port E bit 6 |
| Chân 14 | PE7 — Port E bit 7 |
| Chân 15 | PJ0 — Port J bit 0 (XGATE interrupt capable) |
| Chân 16 | PJ1 — Port J bit 1 |
| Chân 17 | PJ2 — Port J bit 2 |
| Chân 18 | PJ3 — Port J bit 3 |
| Chân 19 | PJ4 — Port J bit 4 |
| Chân 20 | PJ5 — Port J bit 5 |
| Chân 21 | PJ6 — Port J bit 6 |
| Chân 22 | PJ7 — Port J bit 7 |
| Chân 23 | BKGD — Background Debug Mode pin (BDM) |
| Chân 24 | RESET — External reset input (active low) |
| Chân 25 | TEST — Test mode pin - tie to VDDX per datasheet |
| Chân 26 | XFC — PLL filter capacitor |
| Chân 27 | EXTAL — Crystal/clock input |
| Chân 28 | XTAL — Crystal output |
| Chân 29 | PAD00 — Port AD bit 0 / ATD channel 0 |
| Chân 30 | PAD01 — Port AD bit 1 / ATD channel 1 |
| Chân 31 | PAD02 — Port AD bit 2 / ATD channel 2 |
| Chân 32 | PAD03 — Port AD bit 3 / ATD channel 3 |
| Chân 33 | PAD04 — Port AD bit 4 / ATD channel 4 |
| Chân 34 | PAD05 — Port AD bit 5 / ATD channel 5 |
| Chân 35 | PAD06 — Port AD bit 6 / ATD channel 6 |
| Chân 36 | PAD07 — Port AD bit 7 / ATD channel 7 |
| Chân 37 | PAD08 — Port AD bit 8 / ATD channel 8 |
| Chân 38 | PAD09 — Port AD bit 9 / ATD channel 9 |
| Chân 39 | PAD10 — Port AD bit 10 / ATD channel 10 |
| Chân 40 | PAD11 — Port AD bit 11 / ATD channel 11 |
| Chân 41 | PAD12 — Port AD bit 12 / ATD channel 12 |
| Chân 42 | PAD13 — Port AD bit 13 / ATD channel 13 |
| Chân 43 | PAD14 — Port AD bit 14 / ATD channel 14 |
| Chân 44 | PAD15 — Port AD bit 15 / ATD channel 15 |
| Chân 45 | PAD16 — Port AD bit 16 |
| Chân 46 | PAD17 — Port AD bit 17 |
| Chân 47 | PAD18 — Port AD bit 18 |
| Chân 48 | PAD19 — Port AD bit 19 |
| Chân 49 | PAD20 — Port AD bit 20 |
| Chân 50 | PAD21 — Port AD bit 21 |
| Chân 51 | PAD22 — Port AD bit 22 |
| Chân 52 | PAD23 — Port AD bit 23 |
| Chân 53 | PA0 — Port A bit 0 / ECT channel 0 |
| Chân 54 | PA1 — Port A bit 1 / ECT channel 1 |
| Chân 55 | PA2 — Port A bit 2 / ECT channel 2 |
| Chân 56 | PA3 — Port A bit 3 / ECT channel 3 |
| Chân 57 | PA4 — Port A bit 4 / ECT channel 4 |
| Chân 58 | PA5 — Port A bit 5 / ECT channel 5 |
| Chân 59 | PA6 — Port A bit 6 / ECT channel 6 |
| Chân 60 | PA7 — Port A bit 7 / ECT channel 7 |
| Chân 61 | PB0 — Port B bit 0 / ECT channel 0 alt |
| Chân 62 | PB1 — Port B bit 1 / ECT channel 1 alt |
| Chân 63 | PB2 — Port B bit 2 / ECT channel 2 alt |
| Chân 64 | PB3 — Port B bit 3 / ECT channel 3 alt |
| Chân 65 | PB4 — Port B bit 4 / ECT channel 4 alt |
| Chân 66 | PB5 — Port B bit 5 / ECT channel 5 alt |
| Chân 67 | PB6 — Port B bit 6 / ECT channel 6 alt |
| Chân 68 | PB7 — Port B bit 7 / ECT channel 7 alt |
| Chân 69 | PP0 — Port P bit 0 / PWM channel 0 |
| Chân 70 | PP1 — Port P bit 1 / PWM channel 1 |
| Chân 71 | PP2 — Port P bit 2 / PWM channel 2 |
| Chân 72 | PP3 — Port P bit 3 / PWM channel 3 |
| Chân 73 | PP4 — Port P bit 4 / PWM channel 4 |
| Chân 74 | PP5 — Port P bit 5 / PWM channel 5 |
| Chân 75 | PP6 — Port P bit 6 / PWM channel 6 |
| Chân 76 | PP7 — Port P bit 7 / PWM channel 7 |
| Chân 77 | PS0 — Port S bit 0 / SPI0 |
| Chân 78 | PS1 — Port S bit 1 / SPI0 SCK |
| Chân 79 | PS2 — Port S bit 2 / SPI0 MOSI |
| Chân 80 | PS3 — Port S bit 3 / SPI0 MISO |
| Chân 81 | PS4 — Port S bit 4 / SCI0 TX |
| Chân 82 | PS5 — Port S bit 5 / SCI0 RX |
| Chân 83 | PS6 — Port S bit 6 / SCI1 TX |
| Chân 84 | PS7 — Port S bit 7 / SCI1 RX |
| Chân 85 | PT0 — Port T bit 0 / IIC SCL |
| Chân 86 | PT1 — Port T bit 1 / IIC SDA |
| Chân 87 | PT2 — Port T bit 2 / CAN0 TX |
| Chân 88 | PT3 — Port T bit 3 / CAN0 RX |
| Chân 89 | PT4 — Port T bit 4 / CAN1 TX |
| Chân 90 | PT5 — Port T bit 5 / CAN1 RX |
| Chân 91 | PT6 — Port T bit 6 |
| Chân 92 | PT7 — Port T bit 7 |
| Chân 93 | PM0 — Port M bit 0 |
| Chân 94 | PM1 — Port M bit 1 |
| Chân 95 | PM2 — Port M bit 2 |
| Chân 96 | PM3 — Port M bit 3 |
| Chân 97 | PM4 — Port M bit 4 |
| Chân 98 | PM5 — Port M bit 5 |
| Chân 99 | PM6 — Port M bit 6 |
| Chân 100 | PM7 — Port M bit 7 |
| Chân 101 | VDDPLL — Internal PLL supply |
| Chân 102 | VSSPLL — Internal PLL ground |
| Chân 103 | VDDX3 — External supply 3 |
| Chân 104 | VSSX3 — External ground 3 |
| Chân 105 | VDDX4 — External supply 4 |
| Chân 106 | VSSX4 — External ground 4 |
| Chân 107 | VDD2 — Internal regulator output (2.5 V) |
| Chân 108 | VSS2 — Internal regulator ground |
| Chân 109 | PK0 — Port K bit 0 |
| Chân 110 | PK1 — Port K bit 1 |
| Chân 111 | PH0 — Port H bit 0 |
| Chân 112 | PH1 — Port H bit 1 |
Ứng dụng tiêu biểu
S912XEQ384J3VAL phù hợp cho 7 Áp dụngs: Automotive Body Control Module (BCM), Instrument Cluster and Driver Display Controllers, HVAC Control Modules with Actuator Drivers, Industrial CAN-Open Node Controllers, Maritime and Off-Road Vehicle Telematics, Solar Inverter and Renewable-Energy Controllers, Aerospace Auxiliary Control and Sensor Concentrators.
Automotive Body Control Module (BCM)
The S912XEQ384J3VAL's 50 MHz S12X core, XGATE co-processor and 12-bit ATD ADC fit automotive BCM functions including central locking, exterior lighting and wiper control, where multiple CAN nodes must respond deterministically to wake events. The 384 KB Flash holds typical application firmware plus CAN J1939 stacks, while 16 KB RAM buffers pending diagnostic messages. Unlike an MCU without XGATE, the XGATE engine offloads CAN interrupt servicing and PWM generation into a peripheral context with sub-microsecond latency, removing the need for an external real-time companion. The 112-LQFP (20x20) footprint supports legacy Freescale-designed PCBs and AEC-Q100 Grade 1 qualification supports under-hood deployment.
Được đề xuất
Instrument Cluster and Driver Display Controllers
The XEQ sub-family's Memory Protection Unit (MPU) and supervisor/user modes let instrument cluster firmware safely run graphics, diagnostics and CAN traffic on a single S912XEQ384J3VAL while keeping safety-critical turn signals isolated in supervisor mode. The 16-bit Enhanced Capture Timer (ECT) supports the precise PWM timing required for stepper-motor gauge and buzzer control, and 12-bit ATD channels handle fuel and temperature sensor inputs. AEC-Q100 Grade 1 qualification across -40C to +105C allows placement behind the dashboard where ambient temperature swings are significant.
Được đề xuất
HVAC Control Modules with Actuator Drivers
The S912XEQ384J3VAL's ECT, 12-bit ATD and SCI peripheral set is well aligned to HVAC control modules that read cabin temperature, blend door position and blower RPM, then drive multiple DC and stepper actuators. The XGATE co-processor maintains deterministic update of the actuator PWM, keeping the main core free for CAN diagnostics and protocol stacks. 384 KB Flash accommodates full AUTOSAR configuration memory plus application code. The AEC-Q100 -40C to +105C window comfortably covers the in-cabin environment including solar load.
Được đề xuất
Industrial CAN-Open Node Controllers
Factory automation CAN-Open nodes using the S912XEQ384J3VAL benefit from its dual CAN 2.0 controllers, SCI for service-port access, and SPI for ADC or sensor expansion. The 384 KB Flash scales to CAN-Open stack plus application logic while 16 KB RAM covers PDO buffers. Compared with a Cortex-M class alternative, the S12X core's deterministic interrupt response makes it a strong fit for time-critical conveyor or pick-and-place nodes. The same tooling infrastructure that supports automotive BCMs reduces qualification overhead for industrial customers.
Được đề xuất
Maritime and Off-Road Vehicle Telematics
Off-road and marine telematics controllers leverage the S912XEQ384J3VAL's wide automotive-grade temperature range, 384 KB Flash for CAN J1939 diagnostics, and the S12X core's strong IEC 61508 track record for the auxiliary safety functions sometimes mandated in heavy-vehicle and marine ECUs. The XGATE engine handles incoming CAN messages deterministically while the main core runs application logic and GPS/GLONASS stacks. AEC-Q100 screening provides a defence against vibration and humidity stresses.
Được đề xuất
Solar Inverter and Renewable-Energy Controllers
Although marketed primarily for automotive, the S912XEQ384J3VAL is also used in small photovoltaic inverter controllers and renewable-energy junction nodes that benefit from CAN/SCIs robust bus interfaces and AEC-Q100 Grade 1 thermal headroom. The 16-bit S12X core and ECT provide reliable cycle-by-cycle current control, while XGATE offloads inverter switching events from main core processing. The 112-LQFP footprint simplifies board layout reuse across solar platforms originally designed around legacy Freescale products.
Được đề xuất
Aerospace Auxiliary Control and Sensor Concentrators
General-aviation sensor concentrators and auxiliary control units use the S912XEQ384J3VAL because it offers -40C to +105C operation with AEC-Q100 screening, 384 KB Flash, and CAN 2.0 interfaces common in avionics databuses. The Memory Protection Unit enables supervisor/user separation, useful for partitioned DO-178 firmware baselines. XGATE service routines maintain deterministic timing when multiple sensor inputs converge. Note: DO-160 qualification at the system level remains the integrator's responsibility.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho S912XEQ384J3VAL — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | S912XEQ384J3CAL | S912XEQ384J3CALR | S912XEG384J2CALR | S912XEQ384F1VAL | S912XEQ512J2MAL |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 112-LQFP (20x20 mm) | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same | 112-LQFP (20x20 mm) - same |
| Program Flash | 384 KB | 384 KB | 384 KB | 384 KB | 384 KB | 512 KB (+33%) |
| RAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 32 KB |
| Core Frequency | 50 MHz / 25 MHz bus | 50 MHz / 25 MHz bus | 50 MHz / 25 MHz bus | 50 MHz / 25 MHz bus | 50 MHz / 25 MHz bus | 50 MHz / 25 MHz bus |
| Co-processor | XGATE | XGATE | XGATE | XGATE | XGATE | XGATE |
| ADC | 12-bit ATD, ~3 us conversion | 12-bit ATD, ~3 us conversion | 12-bit ATD, ~3 us conversion | 12-bit ATD, ~3 us conversion | 12-bit ATD, ~3 us conversion | 12-bit ATD, ~3 us conversion |
| Operating Temperature | -40C to +105C (AEC-Q100 Grade 1) | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C |
| Packaging | Tray | Reel 13-inch | Tape & Reel | Tape & Reel | Tray | Tray |
Bảo phân biệt quan trọng
- XGATE peripheral co-processor absent on classical HCS12 (vsMC9S12H256VFVE)
- 384 KB Flash, 16 KB RAM with MPU for software partitioning (vsMC9S12XEG128MAA)
- Production-ready drop-in tray variant within the S12XEQ family (vsS912XEQ384J3CALR)
Ghi chú thiết kế
Estimated: VDDX decoupling requires one 100 nF X7R ceramic per VDDX/VSSX pair located within 5 mm of each pin, plus bulk 4.7 uF on VDDR. The internal 2.5 V regulator (VDD2) requires a 1 uF bypass plus a 4.7 uF bulk. The PLL supply (VDDPLL/VSSPLL) must be filtered with a ferrite or RC from VDDX. Dropping these loops causes POR faults and reduces AEC-Q100 margin at low temperature.
Keep the EXTAL/XTAL traces short and symmetric, and route the XFC cap with a guarded guard-ring to VSSPLL to minimise PLL jitter. BGND must remain accessible for factory programming - place a 2x5 0.05-inch header or test pad. Place the reset network (4.7 kohm pull-up plus 1 nF delay) close to the RESET pin. Inadequate routing of the XFC capacitor node causes the well-documented XEQ oscillator start-up failure.
Do not assume the production CAL variant is interchangeable on a reel-only SMT line - VAL ships in tray, CAL/CALR ships in 13-inch reel. Confirm compatibility with the S12XEQ derivative mask revision when swapping between F1 and J3; EEPROM emulation offsets and CAN baud timing vary. Plan toolchain migration: legacy CodeWarrior 4.x projects must be rebuilt for CodeWarrior 5.1+ or migrated to S32 Design Studio with maintained BDM probe.
Thông tin tuân thủ
AEC-Q100 Grade 1 per NXP product page. RoHS/REACH compliant per NXP and Arrow listings.
