STM32F410CBU3 - 100MHz Cortex-M4 MCU | STMicroelectronics
MPN: STM32F410CBU3 ✓ Hoạt độngSTM32F410CBU3 Tóm tắt
A microcontroller is a programmable semiconductor that integrates a processor core, Flash program memory, SRAM, peripherals, and communication interfaces into one device. The STM32F410CBU3 fits the hierarchy of embedded controller, 32-bit RISC microcontroller, ARM Cortex-M microcontroller, and STM32 family device. Its 100 MHz processing capability supports responsive control loops, human-machine interfaces, sensor processing, and connected embedded products without requiring a separate processor.
The principal device characteristics visible for this exact ordering code include the ARM Cortex-M4 processor, 32-bit architecture, 100 MHz maximum frequency, 128 KB Flash, and 48-UFQFPN package. The STM32F410x8/B family is positioned by STMicroelectronics around the high-performance Cortex-M4 core. Exact SRAM capacity, voltage limits, peripheral inventories, pin assignments, temperature grades, and clock-tree details should be confirmed in the STM32F410CB technical documentation before schematic capture or firmware configuration.
Typical uses include compact industrial control modules, environmental monitoring equipment, wearable accessories, building-control endpoints, and low-cost connected sensors. The 48-pin package provides more interface options than smaller packages while retaining a surface-mount land pattern suitable for automated assembly. A 7 x 7 mm UFQFPN footprint can reduce board area compared with larger leaded packages, although thermal-pad layout and manufacturing capability must be considered.
The primary design consideration is to confirm the exact pinout, exposed-pad connection, supported supply voltage, peripheral multiplexing, and boot configuration for STM32F410CBU3. Designers should also validate the PCB footprint against the manufacturer drawing and check the programmed firmware against the selected device revision. This page combines confirmed product facts, practical design guidance, and a focused comparison framework for engineers evaluating this MCU.
Bộ thay thế dễ dàng lắp đặt cho STM32F410CBU3 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với STM32F410CBU3 (cùng hình factor và footprint) — khác nhau ở Mounting Type.
STM32F410CBU6
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →STM32F410CBU3TR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
STM32F410C8U7TR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
STM32F410CBU3 Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit ARM Cortex-M4 microcontroller |
| Manufacturer | STMicroelectronics |
| Series | STM32F4 |
| Processor Core | ARM Cortex-M4 |
| Architecture | 32-bit RISC |
| Maximum CPU Frequency | 100 MHz |
| Flash Memory | 128 KB (128K x 8) |
| Hộp | 48-pin UFQFPN (7 x 7 mm) |
| Kiểu lắp đặt | Surface mount |
| DSP Capability | Enabled |
| Trạng thái RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Hướng dẫn cấu hình chân STM32F410CBU3 48-pin ufqfpn (7 x 7 mm)
Cấu hình chân cho STM32F410CBU3 (48-pin ufqfpn (7 x 7 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho STM32F410CBU3.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
STM32F410CBU3 phù hợp cho 6 Áp dụngs: Compact industrial control module, Environmental monitoring sensor hub, Smart building control endpoint, Wearable accessory controller, Connected equipment interface, Digital audio control interface.
Compact industrial control module
The STM32F410CBU3 fits compact control modules that need responsive 32-bit processing without the board area of a larger leaded MCU. Its 100 MHz ARM Cortex-M4 core can handle control tasks, state machines, and protocol servicing while the 48-pin UFQFPN package preserves access to a broad set of mixed-signal and communication pins. The 128 KB Flash provides room for an embedded application, boot logic, and configuration data. Before schematic release, confirm the required GPIO count, analog inputs, timer assignments, supply voltage, and exposed-pad layout against the STM32F410CB documentation.
Được đề xuất
Environmental monitoring sensor hub
The STM32F410CBU3 is appropriate for a compact environmental sensor hub that periodically measures analog and digital inputs, applies filtering, and forwards results through a serial interface. Its Cortex-M4 processing capability provides more headroom than a very small 8-bit controller, while 128 KB Flash accommodates firmware, calibration tables, and communication logic. The 48-pin package supports integration of sensors, status indicators, and an external communications transceiver. Confirm the ADC characteristics, comparator resources, low-power modes, and required peripheral mappings before finalizing the sensor board.
Được đề xuất
Smart building control endpoint
The STM32F410CBU3 can serve as the local controller in a smart building endpoint that reads room controls, drives indicators or relays, and maintains a network connection. Its 100 MHz core supports responsive user interactions and protocol processing, while the 48-pin UFQFPN footprint permits a compact module with dense routing. The STM32F410CB family's DSP-oriented Cortex-M4 feature set can also assist with signal conditioning. Validate available communication peripherals, pin multiplexing, timer channels, and electrical limits so the chosen communications method is available on the exact package.
Được đề xuất
Wearable accessory controller
The STM32F410CBU3 suits wearable accessories that combine sensor acquisition, user input, and low-power state management in a small board. Its 100 MHz Cortex-M4 core can service multiple sensor tasks and maintain responsive controls, while the 48-pin UFQFPN package offers more I/O options than the smallest MCU packages. Flash memory can hold a control application and data-processing routines. Before selecting it for a battery-powered design, verify the device's specified sleep and stop currents, analog performance, clock requirements, and total standby-system power budget.
Được đề xuất
Connected equipment interface
The STM32F410CBU3 can act as the protocol and control layer in connected industrial equipment, accepting commands from a host and translating them into sensor reads, actuator commands, or local status reports. Its 100 MHz 32-bit core provides capacity for protocol stacks alongside deterministic application logic, and the 128 KB Flash offers a practical code and configuration budget. The UFQFPN-48 land pattern supports dense two-sided layouts. Engineer the system around the exact peripheral set, pin assignments, clock tree, brownout behavior, and communication timing rather than assuming that every STM32F4 member has identical resources.
Được đề xuất
Digital audio control interface
The STM32F410CBU3 can manage a digital audio system where it performs control, configuration, and signal-routing functions around a dedicated audio codec or DSP. The Cortex-M4's DSP capability and 100 MHz operating rate make the MCU appropriate for low-bandwidth audio control and real-time peripheral management, while 128 KB Flash provides storage for firmware and sound-control tables. The 48-pin package can support multiple audio-control signals and communications. Verify the available timer outputs, DMA channels, data interfaces, and pin multiplexing required by the selected audio architecture.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho STM32F410CBU3 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | STM32F410CBU6 | STM32F410CBU3TR | STM32F410C8U7TR |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | UFQFPN-48 (7 x 7 mm) | UFQFPN-48 (7 x 7 mm) | UFQFPN-48 (7 x 7 mm) | UFQFPN-48 (7 x 7 mm) |
| Processor Core | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 | ARM Cortex-M4 |
| Maximum CPU Frequency | 100 MHz | 100 MHz | 100 MHz | 100 MHz |
| Architecture | 32-bit RISC | 32-bit RISC | 32-bit RISC | 32-bit RISC |
| Ordering Suffix | U3 | U6 | U3TR | U7TR |
Bảo phân biệt quan trọng
- Exact STM32F410CBU3 identity retained for assembly matching (vsSTM32F410CBU3TR)
- Maintains the U3 temperature-grade ordering option (vsSTM32F410CBU6)
- Targets 128 KB Flash within the STM32F410CB family (vsSTM32F410C8U7TR)
Ghi chú thiết kế
Use the STMicroelectronics STM32F410CB package drawing to define the 48-pin UFQFPN footprint, including pad dimensions, pitch, solder-mask openings, and the exposed thermal pad. Confirm whether the thermal pad is connected to a supply or ground potential in the selected configuration. Place decoupling capacitors close to their associated pins and route high-current supply paths with adequate copper area to minimize voltage drop and inductive noise.
Plan oscillator, reset, debug, and boot-related nets using the manufacturer pin-description table before assigning peripheral functions. The Cortex-M4 system can be sensitive to clock cleanliness, reset release behavior, and unintended boot-state levels. Keep sensitive analog and communication routes away from fast digital edges, and verify every alternate-function mapping against the exact STM32F410CBU3 package rather than reusing an STM32F4 layout without checking.
Do not treat a shared STM32F410 family designation as proof that every ordering suffix is interchangeable. Check temperature grade, flash-density suffix, packing method, exposed-pad requirements, and lifecycle status. After substituting a candidate, compare the device identifier used by the bootloader or programming tool and run peripheral, clock, brownout, and timing tests on production hardware.
For a UFQFPN package, thermal performance depends strongly on the PCB copper area, thermal-via pattern, internal layers, airflow, and ambient temperature. Route the exposed pad according to the manufacturer's package guidance and provide solder-paste and reflow control consistent with the package documentation. Validate worst-case junction temperature through board-level thermal testing because the compact 7 x 7 mm land pattern may concentrate heat near the device.
Thông tin tuân thủ
The exact compliance declarations and AEC-Q100 qualification status for STM32F410CBU3 were not identified in the cited product pages. Confirm them in the current STMicroelectronics product documentation and applicable material-declaration records.