STM8L152C4T3 - 16MHz 16KB Flash Ultra-Low-Power MCU | STMicroelectronics
MPN: STM8L152C4T3 ✓ Hoạt độngSTM8L152C4T3 Tóm tắt
An ultra-low-power microcontroller is an energy-efficient integrated circuit designed to conserve battery energy by combining low-leakage operation, low-power operating modes, and selective peripheral activation. The STM8L family belongs to the broader hierarchy of 8-bit MCU, microcontroller, embedded processor, and semiconductor products used in sensing, metering, control, communications, and human-interface applications.
The STM8L152C4T3 combines 16 KB of Flash memory with an integrated real-time clock and LCD controller. Its documented peripheral set also includes timers, USART, I2C, SPI, ADC, DAC, and comparators. These resources allow a designer to implement local sensing, display control, data acquisition, serial communication, and actuator drive functions without relying on several separate discrete devices.
Its 16 MHz operating clock provides dedicated processing performance for low-complexity control tasks, while the 41 available I/O ports support compact user interfaces and mixed analog and digital connections. The 1.8 V to 3.6 V operating range accommodates low-voltage battery-powered designs as well as 3.3 V industrial or embedded systems. Component selection should include checking the complete pin description and electrical limits in the manufacturer pinout and datasheet.
Typical uses include battery-powered environmental sensors, compact energy meters, industrial control modules, instrument-panel controllers, low-power data loggers, and connected sensing nodes. The LCD controller and real-time clock are especially useful when the design requires a local display and timekeeping without continuously powering a larger processor or display subsystem.
PCB design should preserve the required decoupling arrangement, connect unused pins according to the manufacturer guidance, and route high-impedance or sensitive analog signals away from fast-switching nodes. Low-power designs must also account for board leakage, pull-up resistance, and the operating mode selected by firmware, because external circuitry can dominate the final sleep-mode current.
This page consolidates the exact orderable MPN, electrical attributes, package information, application guidance, and qualified same-family alternatives into one engineering reference. It also identifies the documentation needed to verify pin assignment, peripheral multiplexing, firmware support, and lifecycle status before a design is released to production.
Bộ thay thế dễ dàng lắp đặt cho STM8L152C4T3 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với STM8L152C4T3 (cùng hình factor và footprint) — khác nhau ở Package, Analog Peripherals, Architecture, Data EEPROM, Flash Memory.
STM8L152C4T6
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
STM8L151C4T6
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →STM8L151C4T3
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →STM8L152C4T3 Tỷ lệ tối đa & tính chất điện
| Microcontroller Type | 8-bit ultra-low-power MCU |
| Maximum CPU Clock | 16 MHz |
| Program Memory | 16 KB Flash |
| Flash Organization | 16K x 8 bits |
| Điện áp cung cấp hoạt động | 1.8 V to 3.6 V |
| I/O Port Count | 41 ports |
| Hộp | 48-pin LQFP, 7 x 7 mm |
| Real-Time Clock | Integrated |
| LCD Controller | Integrated |
| Timers | Integrated |
| Serial Interfaces | USART, I2C, and SPI |
| Analog Peripherals | ADC, DAC, and comparators |
Hướng dẫn cấu hình chân STM8L152C4T3 48-pin lqfp, 7 x 7 mm
Cấu hình chân cho STM8L152C4T3 (48-pin lqfp, 7 x 7 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho STM8L152C4T3.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
STM8L152C4T3 phù hợp cho 6 Áp dụngs: Battery-Powered Environmental Sensor Nodes, Compact Energy and Utility Meters, Low-Power Data Loggers, Industrial Control and Sensor Interface Modules, Instrument Panels and Segmented LCD Displays, Connected Low-Power Sensing Products.
Battery-Powered Environmental Sensor Nodes
The STM8L152C4T3 fits compact environmental sensors that periodically measure an analog input and transmit the result over a low-speed serial link. Its 1.8 V to 3.6 V operating range supports low-energy supply designs, while the ADC and comparators provide local measurement and threshold functions. The 16 MHz clock and integrated timers help schedule sampling and communication activity. Because the MCU supports deep low-power operating modes, firmware can disable unused peripherals between measurements. Final battery-life calculations must include sensor standby current, pull-up networks, regulator quiescent current, and PCB leakage rather than relying on controller power alone.
Được đề xuất
Compact Energy and Utility Meters
The STM8L152C4T3 is suitable for compact metering modules that combine pulse counting, timekeeping, local display support, and low-rate communications. Its integrated real-time clock supports time-stamped records, the timers can capture measurement or pulse events, and the LCD controller is useful for segmented instrument displays. The 41 I/O ports provide ample connections for sensors, buttons, and communication lines within a 7 x 7 mm footprint. Calibration data can be stored in the internal nonvolatile memory identified by the exact device documentation. Meter accuracy ultimately depends on the analog front end, crystal selection, and calibration method.
Được đề xuất
Low-Power Data Loggers
The STM8L152C4T3 can serve as the control device in a low-power data logger that stores timestamped sensor readings and transmits them through USART, I2C, or SPI. Its real-time clock provides the time reference, while timers support precise acquisition and communication intervals. The 16 KB Flash memory is suitable for modest firmware and data-handling functions, although application-specific nonvolatile storage should be added if logs exceed internal capacity. Running the controller between measurement intervals can reduce average energy use. Validate wake timing, sensor stabilization, bus loading, and data-integrity requirements against the complete system specification.
Được đề xuất
Industrial Control and Sensor Interface Modules
The STM8L152C4T3 is appropriate for small industrial modules that combine digital inputs, analog monitoring, local logic, and serial communications. Its 41 I/O ports support multiple sensors and actuators, while the ADC, DAC, and comparators expand the available signal-processing functions. The 1.8 V to 3.6 V range fits 3.3 V control electronics and permits lower-voltage operation where appropriate. Industrial equipment should also provide appropriate isolation, surge protection, grounding, and environmental margins outside the MCU. Firmware should include watchdog, reset-cause, and communication-error recovery mechanisms for reliable unattended operation.
Được đề xuất
Instrument Panels and Segmented LCD Displays
The integrated LCD controller and real-time clock make the STM8L152C4T3 well suited to compact instrument panels with segmented LCD indications. It can manage display updates, button input, timing, and interface communication without a separate display controller. The 48-pin LQFP package provides 41 I/O ports for display segments, switches, indicators, and communications while remaining only 7 x 7 mm. Designers should calculate LCD segment drive requirements, contrast, bias timing, and glass operating limits against the device's LCD specifications. Low-power operation is particularly valuable in fixed-function panels because the display and MCU can be refreshed only when their state changes.
Được đề xuất
Connected Low-Power Sensing Products
The STM8L152C4T3 can act as the low-power controller in a compact connected product that gathers local sensor data and communicates with a higher-level host over USART, I2C, or SPI. Its integrated ADC and comparators support front-end sensing, the DAC can generate an analog output where required, and the timers provide event and timing services. The 16 MHz processor and 16 KB Flash are appropriate for protocol handling and moderate control logic. Connection to a radio or network module remains necessary for wireless operation. Power sequencing, bus pull-ups, antenna integration, and enclosure thermals should be evaluated as part of the complete product design.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho STM8L152C4T3 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | STM8L152C4T6 | STM8L151C4T6 | STM8L151C4T3 |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 48-pin LQFP (7 x 7 mm) | 48-pin LQFP (7 x 7 mm) | 48-pin LQFP (7 x 7 mm) | 48-pin LQFP (7 x 7 mm) |
| Device Type | 8-bit ultra-low-power MCU | 8-bit ultra-low-power MCU | 8-bit ultra-low-power MCU | 8-bit ultra-low-power MCU |
| Program Memory | 16 KB Flash | 16 KB Flash | 16 KB Flash | 16 KB Flash |
| Integrated Analog and Timing Resources | ADC, DAC, comparators, timers, and real-time clock | STM8L152 variant peripheral set | STM8L151 variant; LCD and DAC feature differences require verification | STM8L151 variant; LCD and DAC feature differences require verification |
Bảo phân biệt quan trọng
- Broad integrated peripheral set in the 48-pin footprint (vsSTM8L151C4T6)
- Matching flash and maximum-clock configuration (vsSTM8L152C4T6)
- Same STM8L152 variant architecture with a distinct temperature suffix (vsSTM8L151C4T3)
Ghi chú thiết kế
Design the STM8L152C4T3 supply around its documented 1.8 V to 3.6 V operating range. Place the manufacturer's specified input and output decoupling capacitors close to their associated pins, maintain the required supply ramp behavior, and keep analog and digital return currents under a common low-impedance ground strategy. For battery-powered systems, include regulator dropout, quiescent current, and peripheral load current in the energy budget because the MCU alone does not determine total standby consumption.
Assign all 48 LQFP positions from the manufacturer pin-description table before schematic capture. Verify programming pins, reset, clock, power, ground, LCD, ADC, DAC, comparator, and communication functions because alternate-function multiplexing can constrain the usable 41 I/O ports. Keep sensitive analog inputs short and away from switching nodes, provide a quiet reference return, and route high-current outputs separately from low-level sensing paths to reduce coupling.
Do not treat a shared STM8L family name or LQFP outline as proof of drop-in compatibility. The STM8L151 and STM8L152 variants differ in their documented peripheral mix, particularly around LCD and DAC functionality, and temperature suffixes can impose different operating limits. Before replacing STM8L152C4T3, compare every used pin, alternate function, supply limit, clock setting, bootloader interface, and firmware target in the manufacturer documentation.
Thông tin tuân thủ
Compliance status could not be extracted for the exact STM8L152C4T3 orderable MPN from the listed documentation.
