TS393ID - Dual Micropower CMOS Comparator | STMicroelectronics
MPN: TS393ID ✓ Hoạt độngTS393ID Tóm tắt
A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The TS393ID belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its CMOS implementation emphasizes low supply current, and its open-drain outputs allow multiple devices to share a common pull-up when wired-AND behavior is required. These characteristics place it between simple threshold logic and more complex analog front ends.
The primary features include two independent CMOS comparators, a 2.7 V to 16 V supply range, and 9 µA typical current consumption per comparator. Each output is open drain and requires an external pull-up resistor when a logic-high output is required. The SOIC-8 package provides a conventional surface-mount footprint suitable for compact industrial, consumer, instrumentation, and embedded-control designs. The manufacturer also identifies the TS3702 as a related dual micropower comparator offering similar performance with push-pull CMOS outputs.
Electrically, the open-drain stage can pull its output low but cannot actively drive a high level. This gives designers control over rise time through the pull-up resistor and allows several comparator outputs to share a bus. That flexibility is useful in battery-powered equipment where minimizing activity is important, although the external pull-up contributes its own continuous current after an output is released. The two channels can compare different signal pairs or operate together for window supervision.
Typical applications include battery-powered threshold detection, sensor signal conditioning, overvoltage and undervoltage indication, temperature-alarm circuits, industrial control interfaces, and low-power monitoring modules. The comparator may be used with op-amp-like input networks, dividers, current sensors, or digital control inputs where the required decision is binary. Because output polarity and timing determine system behavior, both input and output details should be checked against the manufacturer datasheet before final circuit release.
A key design consideration is the external pull-up on each open-drain output. Select its resistance to balance noise immunity, switching speed, and power consumption, then confirm that every connected output can safely share the same node. Account for input common-mode limits, supply decoupling, output rise time, and any required hysteresis. The two channels are independent, so grounding or signal-conditioning requirements should be evaluated separately for each comparator.
This page combines the TS393ID's verified electrical and packaging characteristics with drop-in candidate evaluation, parameter-by-parameter comparison, sourcing guidance, and practical circuit-design notes. It is intended to accelerate component selection while preserving the need to confirm detailed operating limits and timing behavior against the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho TS393ID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TS393CD
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM293DGKRG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TS393ID Tỷ lệ tối đa & tính chất điện
| Comparator Count | 2 |
| Supply Voltage Range | 2.7 V to 16 V |
| Supply Current per Comparator | 9 µA typical |
| Comparator Technology | CMOS |
| Kiểu đầu ra | Open drain |
| Device Type | General-purpose voltage comparator |
| Hộp | 8-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Số lượng chân | 8 pins |
| Low-Power Characteristic | Approximately 20 times lower typical supply consumption per comparator than bipolar LM393 |
| Output Pull-Up Requirement | External pull-up required for open-drain outputs |
| Related Push-Pull Comparator | TS3702 |
Hướng dẫn cấu hình chân TS393ID 8-pin soic
Cấu hình chân cho TS393ID (8-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TS393ID.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TS393ID phù hợp cho 6 Áp dụngs: Battery-Powered Threshold Detection, Sensor Signal Conditioning, Overvoltage and Undervoltage Supervision, Industrial Control and Process Monitoring, Temperature and Level Alarm Circuits, Low-Power Logic Interlocking.
Battery-Powered Threshold Detection
The TS393ID fits battery-powered threshold detection because each comparator typically consumes only 9 µA while operating across a 2.7 V to 16 V supply range. Place one channel across a divided sensor or supply signal and use the other for an independent limit when additional monitoring is needed. Because both outputs are open drain, fit the required pull-up resistors close to the device and select their resistance to minimize standby current while maintaining a clean logic-high transition. The STMicroelectronics datasheet identifies current consumption as approximately 20 times lower than the bipolar LM393, making the TS393ID attractive for portable sensing equipment where continuous comparator draw matters.
Được đề xuất
Sensor Signal Conditioning
The TS393ID can convert an analog sensor condition into a digital decision for an embedded controller or monitoring system. Use each independent comparator channel with its own divider, reference, or sensor interface, and add positive feedback when hysteresis is required to prevent repeated switching around the threshold. Its 9 µA typical current per comparator and 2.7 V minimum supply support low-energy signal conditioning, while the 8-pin SOIC package simplifies board assembly. The open-drain output requires an external pull-up, so verify that the resulting rise time satisfies the receiving circuit and that the sensor signal remains inside the device's input common-mode limits.
Được đề xuất
Overvoltage and Undervoltage Supervision
The TS393ID supports compact overvoltage and undervoltage supervision by using its two independent comparator channels to compare divided supply rails with a reference. The 2.7 V to 16 V operating range makes it applicable to multiple low- and moderate-voltage systems, while 9 µA typical current per comparator reduces the burden of always-on protection circuitry. Use resistor-divider ratios that keep both sensed nodes within the comparator's permitted common-mode range. Because the outputs are open drain, a shared pull-up can provide a common fault indication if the design deliberately supports wired-AND behavior; otherwise, use separate pull-ups for independent warning and fault signals.
Được đề xuất
Industrial Control and Process Monitoring
The TS393ID is appropriate for industrial process-monitoring modules that must compare a control signal or scaled process value with a fixed threshold. Its dual-channel architecture allows one circuit to perform both limit checks without requiring two separate packages, and its 9 µA typical current per comparator helps isolate monitoring functions that remain active continuously. The 8-pin SOIC format supports conventional surface-mount assembly, but layout still requires a stable supply plane, close input routing, and careful pull-up placement. Confirm operating-temperature limits, input common-mode behavior, and response timing in the STMicroelectronics datasheet before deploying the device in safety-critical or high-noise industrial equipment.
Được đề xuất
Temperature and Level Alarm Circuits
The TS393ID can implement a temperature alarm or tank-level limit detector when the measured quantity is converted into a voltage that crosses a reference threshold. Two channels may monitor separate alarm points, allowing a compact module to report both high and low conditions. Its 9 µA typical consumption per comparator is valuable in remote or battery-backed monitoring, and the 2.7 V minimum operating voltage supports low-voltage sensor systems. Add hysteresis to prevent chatter around the transition point, use a pull-up matched to the required rise time, and confirm that the transducer output remains within the comparator's input common-mode range under all expected temperature or level conditions.
Được đề xuất
Low-Power Logic Interlocking
The TS393ID can create compact logic interlocks where two conditions must be compared before another circuit is permitted to operate. Its two independent open-drain channels can represent separate permissive or inhibit signals, and multiple outputs may share a pull-up when wired-AND behavior is useful. The low typical consumption of 9 µA per comparator reduces the impact of continuous supervision, while the 16 V maximum supply supports systems above low-voltage logic levels. Keep the shared output node short and properly pulled up, account for the RC-defined rising edge, and validate every input's voltage range. The TS3702 is a related option when push-pull outputs are preferred over open-drain behavior.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TS393ID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TS393CD | LM293DGKRG4 |
|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | STMicroelectronics | STMicroelectronics | Texas Instruments |
| Comparator Count | 2 | 2 | 2 |
| Comparator Technology | CMOS | CMOS | Bipolar |
| Output Type | Open drain | Open drain | Open collector |
| Relative Consumption | Approximately 20 times lower than the bipolar LM393 | Approximately 20 times lower than the bipolar LM393 | Reference dual bipolar comparator |
| External Pull-Up Requirement | Required for open-drain outputs | Required for open-drain outputs | Required for open-collector outputs |
| Pin Count | 8 pins | 8 pins | 8 pins |
Bảo phân biệt quan trọng
- Lower typical channel current than a bipolar LM393 reference (vsLM293DGKRG4)
- Same-family replacement path in an 8-pin SOIC package (vsTS393CD)
- Shared open-drain bus capability (vsTS3702)
Ghi chú thiết kế
Do not treat an open-drain output as a complete logic output. Each channel requires an external pull-up unless it is intentionally connected to a shared wired-AND node. Calculate the pull-up current from the lowest output voltage and verify the logic-high level at the receiver. The resistor also sets the output rise time together with bus capacitance, so overly large values can cause timing failures even when static logic levels appear correct.
The TS393ID's 9 µA typical current per comparator is low, but system standby consumption can still be dominated by external networks. Use high-value resistor dividers where their resistance and leakage remain acceptable, avoid excessive pull-up current, and disconnect unused channels according to the datasheet guidance. Evaluated current should include both comparator channels, pull-up loading, input-bias effects, and any always-active external reference circuit.
Place the supply bypass capacitor close to the device's supply and ground pins, and keep input-divider and feedback traces short to reduce noise pickup and switching transients. Route comparator inputs away from fast digital or switching-node traces. If outputs share a pull-up, keep that node compact to minimize capacitive loading and preserve the intended rise time, especially when one channel changes state while another remains active.
Use positive feedback to create hysteresis when the compared signal can cross the threshold slowly or exhibit noise. Confirm the resulting upper and lower switching thresholds against the application requirements. Also verify the input common-mode range across temperature and supply variation; a correct reference voltage does not guarantee correct operation if either input node approaches or exceeds the allowed input range.
Thông tin tuân thủ
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements are present in the cited product information. Confirm material-compliance documentation with STMicroelectronics for the exact ordering code.
