TS507CD - 1.9MHz Precision Rail-to-Rail Op Amp | STMicroelectronics
MPN: TS507CD ✓ Hoạt độngTS507CD Tóm tắt
An operational amplifier is a voltage-feedback amplifier used to amplify, buffer, filter, or compare small analog signals. The TS507 belongs to the operational-amplifier hierarchy within analog ICs and broader semiconductor signal-conditioning systems. Its rail-to-rail input stage accepts signals close to the supply rails, while the rail-to-rail output stage provides useful output swing near both limits.
The TS507CD uses precision trimming to achieve low input-offset voltage without external zeroing. Its listed maximum input-offset voltage is 550 µV, and its typical common-mode rejection ratio is 115 dB. A 1.9 MHz gain-bandwidth product supports general-purpose closed-loop operation, while the low 850 µA supply current suits low-power analog systems.
The device is specified as a single general-purpose amplifier in an 8-SOIC package. Its operating temperature range is listed as 0°C to 85°C, and its typical output-current capability is 128 mA. These characteristics make it appropriate for precision sensor interfaces, active filters, signal buffers, and portable equipment where low offset and low supply current are more important than high bandwidth.
Typical uses include bridge-sensor amplification, transducer-signal conditioning, low-frequency active filters, and buffered analog measurements. Because the amplifier operates rail-to-rail at the input and output, system designers can use more of the available supply range, but common-mode and output-swing limits still require verification under the intended load and supply conditions.
When laying out a TS507CD circuit, keep feedback components and the input source connections short, and route high-impedance inputs away from switching nodes. Decoupling capacitors should be placed close to the supply and ground pins. Confirm gain-bandwidth, output-swing, and stability requirements against the actual gain, load, supply voltage, and operating temperature.
This page combines the TS507CD device description, package information, application guidance, comparison parameters, and verified sourcing references to help engineers evaluate the amplifier and identify technically suitable alternatives before PCB release.
Bộ thay thế dễ dàng lắp đặt cho TS507CD — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TS507CD (cùng hình factor và footprint) — khác nhau ở Package.
TS507ID
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →TS507CLT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TS507ILT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TS507IYLT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TS507CDT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TS507CD Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single general-purpose operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 1.9 MHz |
| Input Offset Voltage | 550 µV maximum |
| Common-Mode Rejection Ratio | 115 dB typical |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Điện áp cung cấp | 850 µA typical |
| Output Current | 128 mA typical |
| Offset Trimming | Internal precision trimming; no external zeroing required |
| Nhiệt độ hoạt động | 0°C to 85°C |
| Hộp | 8-SOIC, 3.90 mm nominal width |
| Kiểu lắp đặt | Surface mount |
| Trạng thái RoHS | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
Hướng dẫn cấu hình chân TS507CD 8-soic, 3.90 mm nominal width
Cấu hình chân cho TS507CD (8-soic, 3.90 mm nominal width gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TS507CD.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TS507CD phù hợp cho 6 Áp dụngs: Precision Sensor Signal Conditioning, Low-Frequency Active Filters, Battery-Powered Instrumentation, Analog Buffering, Threshold and Comparison Circuits, Industrial Process Measurement.
Precision Sensor Signal Conditioning
The TS507CD is well suited to conditioning low-level sensor outputs because its input-offset voltage is specified at no more than 550 µV and its common-mode rejection ratio reaches 115 dB typical. It can amplify a bridge, resistive sensor, or low-level transducer signal while the rail-to-rail input stage accommodates signals near either supply rail. According to the STMicroelectronics datasheet, internal trimming avoids external offset-zeroing components, reducing calibration overhead. Place the amplifier close to the sensor, keep high-impedance inputs short, and verify input bias-current error against the sensor source impedance.
Được đề xuất
Low-Frequency Active Filters
The TS507CD can implement low-frequency active filters because its 1.9 MHz gain-bandwidth product provides useful open-loop bandwidth for precision filter stages. Its 850 µA typical supply current also reduces the penalty when several amplifier sections operate from a compact analog supply. Rail-to-rail input and output behavior can increase signal range within the supply envelope. According to the STMicroelectronics datasheet, the TS507 maintains stable characteristics over its supply range. Select resistor values for the intended gain and frequency, then verify phase margin, output swing, and noise at each practical operating point.
Được đề xuất
Battery-Powered Instrumentation
The TS507CD fits portable measurement systems where amplifier power must remain modest without sacrificing DC precision. Its supply current is 850 µA typical, while the 550 µV maximum input offset and 115 dB typical CMRR help preserve measurement accuracy in low-level analog channels. Rail-to-rail operation allows useful signal handling when the system operates near its supply limits. According to the STMicroelectronics datasheet, the device is a high-performance precision amplifier with internally trimmed offset. Account for resistor divider currents, sensor leakage, regulator quiescent current, and output-load demand in the complete battery budget.
Được đề xuất
Analog Buffering
The TS507CD can buffer high-impedance sources before feeding a sampling or processing stage. A voltage follower takes advantage of the amplifier’s low offset voltage and high common-mode rejection while avoiding loading of the source. The 1.9 MHz gain-bandwidth product provides ample bandwidth for many slow industrial and instrumentation signals. According to the STMicroelectronics datasheet, the rail-to-rail input stage accepts signals near the supply limits. Confirm the source impedance, capacitive loading, output-current demand, and stability behavior; adding a small isolation resistor at the output can help isolate downstream capacitance.
Được đề xuất
Threshold and Comparison Circuits
The TS507CD supports precision threshold detection when a low-level signal must be compared against a reference. Its maximum input-offset voltage of 550 µV limits the input-referred threshold error, and the 115 dB typical CMRR reduces output movement as common-mode voltage changes. The rail-to-rail output stage can produce useful logic-level transitions when supply and loading conditions are appropriate. According to the STMicroelectronics datasheet, the device is intended for stable general-purpose precision amplification. Check output saturation, input range, noise around the threshold, and propagation behavior for the specific comparator configuration.
Được đề xuất
Industrial Process Measurement
The TS507CD is suitable for process-measurement channels that combine moderate bandwidth with low DC error. The 1.9 MHz gain-bandwidth product supports many sensor and actuator signals, while rail-to-rail input operation is useful when the source voltage approaches a supply rail. Its 850 µA typical supply current is modest for continuously powered equipment. According to the STMicroelectronics datasheet, the TS507 provides very low offset through internal trimming. For industrial deployment, verify the exact operating-temperature grade, transient immunity, isolation requirements, and stable reference components around the measurement chain.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TS507CD — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TS507ID | TS507CLT | TS507ILT | TS507IYLT | TS507CDT |
|---|---|---|---|---|---|---|
| Manufacturer | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 1.9 MHz | 1.9 MHz | 1.9 MHz | 1.9 MHz | 1.9 MHz | 1.9 MHz |
| Input and Output Range | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
| Offset Trimming | Internal trimming; no external zeroing | Internal trimming; no external zeroing | Internal trimming; no external zeroing | Internal trimming; no external zeroing | Internal trimming; no external zeroing | Internal trimming; no external zeroing |
Bảo phân biệt quan trọng
- Precision offset performance with internal trimming (vsGeneral-purpose 8-SOIC operational amplifiers)
- Strong common-mode rejection for rail-to-rail input operation (vsTS507CLT)
- Low supply demand for portable analog channels (vsTS507ID)
Ghi chú thiết kế
Place the TS507CD close to the signal source and keep the inverting feedback loop compact. High-impedance input and feedback nodes should have short traces and minimal parasitic capacitance because they can pick up interference and affect noise gain. Route away from switching nodes and motor-control return currents. Follow the manufacturer datasheet pin-configuration diagram during layout and keep ground returns continuous beneath the analog circuitry.
Use the decoupling network and component placement specified in the manufacturer datasheet, placing the required capacitor directly between the supply and ground pins. A short, low-inductance path is more effective than a distant capacitor because the lead and board inductance can dominate at higher frequencies. Keep analog and digital return currents separated where possible, and use a continuous ground plane with careful routing beneath sensitive amplifier inputs.
Do not assume that rail-to-rail input and output operation permits output voltages exactly at the supply rails under every load. Verify output swing, output-current capability, and stable operation with the actual supply voltage and load. Also account for input bias-current error, resistor tolerances, and the 550 µV maximum offset voltage. These checks are particularly important when the source impedance is high or the measured signal is small.
For capacitive loads, start with a small isolation resistor between the amplifier output and the load if the application permits. Confirm stability with the intended gain, load, supply, and temperature rather than relying only on nominal gain-bandwidth product. The 1.9 MHz bandwidth is sufficient for many low-frequency measurement circuits, but high noise gain or heavy capacitive loading can reduce usable bandwidth and phase margin.
Thông tin tuân thủ
No explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement appears in the cited product information.
