TS931AID - 100kHz Rail-to-Rail Output Op Amp, SOIC-8 | STMicroelectronics
MPN: TS931AID ✓ Hoạt độngTS931AID Tóm tắt
An operational amplifier (op amp) is a differential-input voltage amplifier whose gain is set by external feedback components. A rail-to-rail (RRO) output amplifier can swing its output close to both supply rails, so the output remains useful even when the signal approaches the supply limits. In the classification hierarchy, the TS931AID is an operational amplifier, which is a type of amplifier IC, which falls under integrated circuits and analog signal conditioning. Micro-power rail-to-rail op amps occupy the intersection of battery-powered sensing, portable instrumentation, and low-leakage buffer applications.
Key differentiating features of the TS931AID include rail-to-rail output operation, operation from a 2.7 V minimum supply, a 100 kHz unity-gain bandwidth, an 8-pin SOIC footprint with gull-wing leads, and industrial temperature grading. Because output swing reaches 2.9 Vpp at 3 V supply with a light 100 kOhm load, the part is a good fit for buffered sensor front-ends and low-voltage signal chains where headroom is tight. Note that the TS931AID is characterized for output rail-to-rail behaviour; input common-mode range figures should be confirmed against the manufacturer datasheet before committing to a design that relies on input operation near the rails.
Technically, the TS931AID is a single-amplifier device in the TS93x line, which also includes dual and quad members. The 100 kHz gain-bandwidth product places the part firmly in the micropower/general-purpose segment rather than the precision or high-speed segments, meaning it is intended for signal conditioning, buffering, and level shifting where bandwidth requirements are modest but power consumption and rail-to-rail reach matter more.
Typical applications include battery-powered sensor conditioning in industrial and medical monitoring equipment, low-voltage audio and communication signal buffering, and post-processing stages in data acquisition systems. Because the family supports supply voltages down to 2.7 V, it pairs well with coin cells, single Li-ion cells, and low-voltage energy-harvesting front-ends.
When designing with the TS931AID, keep the output load within the range used for the quoted 2.9 Vpp swing figure and place a decoupling capacitor close to the supply pins. Verify the input common-mode range and output swing under load in the manufacturer datasheet, and check the noise and offset specifications against your signal-chain budget before committing the design.
This page consolidates distributor sourcing data, pin-compatible drop-in alternatives, a parameter-by-parameter comparison table, and practical design guidance for the TS931AID that you will not find in a single manufacturer datasheet page.
Bộ thay thế dễ dàng lắp đặt cho TS931AID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TS931AID (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Package, Number of Channels, Input Bias Current, Operating Temperature.
TS931A
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AD8500
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MCP6001
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLV9001IDBVR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →OPA380AID
✅ Drop-In✓ Còn hàng
$1.85 / Đơn vị
Xem tài liệu →TS931AID Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single operational amplifier, rail-to-rail output |
| Number of Circuits | 1 |
| Unity Gain Bandwidth | 100 kHz |
| Minimum Supply Voltage | 2.7 V |
| Output Swing at 3 V Supply | 2.9 Vpp with RL = 100 kOhm |
| Kiểu đầu ra | Rail-to-Rail Output (RRO) |
| Package Type | SOIC-8 (SOP), gull-wing leads |
| Number of Terminals | 8 |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
| Kiểu lắp đặt | Surface mount |
| Series | TS93x (single, dual and quad micropower op amps) |
| Datasheet Document File Size | 973 KB (published 2011-10-21) |
Cấu hình chân TS931AID
| Chân 1 | NC — Not connected (per datasheet) |
| Chân 2 | -IN — Inverting input |
| Chân 3 | +IN — Non-inverting input |
| Chân 4 | V- — Negative supply (ground) |
| Chân 5 | NC — Not connected (per datasheet) |
| Chân 6 | OUT — Output |
| Chân 7 | V+ — Positive supply |
| Chân 8 | NC — Not connected (per datasheet) |
Ứng dụng tiêu biểu
TS931AID phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Signal Conditioning, Low-Voltage Audio Preamplifier, Industrial Data Acquisition Front-End, Medical Monitoring Instrument Signal Chain, Portable IoT Node Level Shifting, Communication and Networking Line Interface.
Battery-Powered Sensor Signal Conditioning
The TS931AID suits coin-cell and single-cell designs because the TS93x series operates from a 2.7 V supply while still swinging 2.9 Vpp into a 100 kOhm load at 3 V. Place the amplifier directly after a resistive or capacitive sensor bridge so the small millivolt-level signal is lifted into a usable range without an intermediate level-shifting stage. The rail-to-rail output stage keeps the conditioned signal full scale even when the battery sags toward its end-of-discharge voltage, and the 100 kHz unity-gain bandwidth is more than adequate for temperature, pressure, and gas sensor signals that change slowly. Confirm the quiescent current in the manufacturer datasheet against the cell capacity budget.
Được đề xuất
Low-Voltage Audio Preamplifier
A 2.9 Vpp output swing at 3 V supply gives the TS931AID useful headroom for small-signal audio stages where every millivolt of range matters. Position it as a headphone or line-level buffer ahead of a class-D or class-AB output stage, where the amplifier must reproduce quiet passages without clipping the rail. The rail-to-rail output keeps the signal inside the usable window on a single-cell supply, while the micropower architecture of the TS93x family limits supply drain in portable audio hardware. Because the 100 kHz bandwidth limits slew rate, design the filter network around the audio band rather than expecting wideband reproduction of transients.
Được đề xuất
Industrial Data Acquisition Front-End
Industrial measurement systems use the TS931AID as a conditioning stage between a bridge sensor and the analog input of a microcontroller or external converter. The single-amplifier SOIC-8 pinout keeps the board simple to route, and the industrial temperature grade suits equipment that operates in uncontrolled plant environments. Buffering the sensor protects the converter input from long cable runs and provides the rail-to-rail swing needed to cover the full transducer range on a compact 3.3 V or 5 V rail. Add a 100 nF decoupling capacitor close to the supply pins and keep feedback resistors close to the device to limit parasitic pickup on long sensor wiring.
Được đề xuất
Medical Monitoring Instrument Signal Chain
Patient monitoring and diagnostic equipment uses the TS931AID in the low-level amplification path ahead of an ADC, where rail-to-rail output swing preserves small physiological signal amplitudes on compact 3 V and 5 V rails. The 100 kHz unity-gain bandwidth comfortably covers ECG, temperature, and pressure sensor bandwidths while the low-power behaviour of the TS93x series limits heat dissipation in battery-powered portable monitors. The 8-pin SOIC footprint allows a compact land pattern with a short feedback loop that avoids added noise from long traces. Use the manufacturer datasheet to confirm input offset and noise contributions against your signal budget.
Được đề xuất
Portable IoT Node Level Shifting
Compact IoT nodes built around 3.3 V microcontroller rails often need to shift a 0 to 5 V or 0 to 3.3 V sensor interface into the logic range of the host processor, and the TS931AID provides that buffer with rail-to-rail output. Its 2.7 V minimum supply allows the same part to run directly from a single-cell supply, and the SOIC-8 package keeps the footprint small enough for a dense sensor node board. The 100 kHz bandwidth is sufficient for status and slow telemetry signals but not for high-rate data, so use a faster alternative such as the MCP6001 when the node handles a fast sensor stream. Keep the output drive current within the rated load to avoid distortion.
Được đề xuất
Communication and Networking Line Interface
Telecom and network equipment front-ends use the TS931AID to buffer slow analog monitor and control lines, where a rail-to-rail output ensures the signal reaches full logic swing on a single 3.3 V or 5 V rail. The series micropower operation keeps the housekeeping circuitry from adding meaningful current draw to powered line cards, and the industrial temperature grade covers outdoor and unheated cabinet deployments. Because the 100 kHz bandwidth rolls off quickly above the audio band, restrict this part to monitoring, alarm, and slow control paths, and pick a higher-bandwidth alternative such as the AD8500 for fast analog channels. Decouple the supply pins locally and keep the feedback loop tight.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TS931AID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TS931A | AD8500 | MCP6001 | TLV9001 | OPA380 |
|---|---|---|---|---|---|---|
| Package | SOIC-8 (SOP) | SOIC-8 (SOP) - same | SOIC-8 (SOP) - same | SOIC-8 (SOP) - same | SOIC-8 (SOP) - same | SOIC-8 (SOP) - same |
| Brand | STMicroelectronics | STMicroelectronics | Analog Devices | Microchip Technology | Texas Instruments | Texas Instruments |
| Number of Circuits | 1 | 1 | 1 | 1 | 1 | 1 |
| Unity Gain Bandwidth | 100 kHz | 100 kHz | 400 kHz | 1 MHz | 1 MHz | 900 kHz |
| Minimum Supply Voltage | 2.7 V | 2.7 V | 2.7 V | 1.8 V | 1.8 V | 1.8 V |
| Output Type | Rail-to-Rail Output | Rail-to-Rail Output | Rail-to-Rail Output | Rail-to-Rail Input and Output | Rail-to-Rail Input and Output | Rail-to-Rail Input and Output |
| Series Membership | TS93x single micropower op amp family | TS93x single micropower op amp family | AD850x micropower RRO family | MCP600x general-purpose RRIO family | TLV900x general-purpose RRIO family | OPA3xx low-noise RRIO family |
Bảo phân biệt quan trọng
- Operates from a 2.7 V minimum supply while maintaining 2.9 Vpp output swing at 3 V (vsMCP6001)
- Rail-to-rail output in the 8-pin standard single-amplifier SOIC footprint (vsOPA380)
- Industrial temperature grade ordering code in the same footprint (vsTS931A)
- Micropower TS93x family positioning versus general-purpose micropower alternatives (vsAD8500)
Ghi chú thiết kế
The TS931AID operates from 2.7 V minimum supply and delivers a 2.9 Vpp output swing at 3 V with a 100 kOhm load, so headroom is tight on single-cell rails. Estimated: with VIN = 3.6 V, VOUT = 1.8 V into an AC-coupled 10 kOhm load, the output stage dissipates roughly (3.6 V - 1.8 V) squared divided by 10 kOhm, giving an average current of about 0.36 mA and an average dissipation near 1.3 mW, which is negligible thermally. The real constraint is output drive into low-impedance loads, so verify the maximum output current and use a series isolation resistor when driving a low-impedance transducer.
Place a 100 nF ceramic decoupling capacitor on the supply pins as close to the device as possible, with the ground return of the capacitor routed directly to the ground pin rather than through the board ground plane. Keep the inverting input and feedback components on the same side of the board as the amplifier to minimize parasitic capacitance that can destabilise the loop with a 100 kHz gain-bandwidth part. Maintain a solid ground pour under and around the SOIC-8 footprint, and route the sensitive input node away from switching nodes and the output trace.
The TS931AID is characterized as a rail-to-rail output amplifier, so do not assume the input can follow the signal all the way to the rails. Using it in an inverting configuration with the signal applied to the inverting input and the non-inverting input grounded works across the full output swing, but a non-inverting stage whose input approaches the positive rail can leave the amplifier's common-mode range before the output saturates. Confirm the input common-mode range in the manufacturer datasheet before biasing the signal close to either rail.
With a 100 kHz unity-gain bandwidth, the open-loop gain roll-off begins well below the audio band, so noise gain peaks near unity gain can dominate the noise performance of a high-gain stage. Keep the closed-loop gain moderate and prefer a two-stage arrangement (a moderate-gain first stage followed by a higher-gain second stage) when large gain is required. Check the stability region and recommended feedback network in the manufacturer datasheet before using high feedback resistors with the non-inverting input biased by a divider.
Estimated: for the TS931AID, supply dissipation scales with the difference between input and output voltage multiplied by the load current plus the quiescent current drawn from the supply. With VIN = 5 V, VOUT = 3.3 V and a 10 mA load, output-stage dissipation is about 17 mW, and the SOIC-8 junction temperature rise stays close to ambient. The device therefore rarely needs a heat sink, but check the maximum supply voltage and total dissipation rating in the manufacturer datasheet before using the part on a 5 V rail with a large drop into a low-impedance load.
Thông tin tuân thủ
No compliance declarations are published for the TS931AID in the manufacturer product material available for this listing. Request the current RoHS, REACH, and lead-free statements from the Request a Quote form, or refer to the STMicroelectronics product page and the manufacturer declaration documents for the TS93x series.