XMC4100F64K128ABXQSA1 - 80MHz Cortex-M4 MCU | Infineon
MPN: XMC4100F64K128ABXQSA1 ✓ Hoạt độngXMC4100F64K128ABXQSA1 Tóm tắt
A microcontroller is a programmable system-on-chip that combines a processor core, nonvolatile program memory, volatile data memory, peripherals, and interface control logic. The Cortex-M4 architecture provides a 32-bit processing platform with deterministic interrupt handling, while the XMC integration adds industrial-oriented peripherals and communication interfaces. The XMC4100F64K128ABXQSA1 therefore occupies the microcontroller -> embedded processor -> industrial control IC hierarchy.
The principal device parameters are an 80 MHz Arm Cortex-M4 core, 128 KB of flash, 20 KB of SRAM, and a 3.3 V operating supply identified for this ordering code. Its documented connectivity includes CAN, I2C, LIN, SPI, UART/USART, and USB interfaces. These interfaces make the device suitable for distributed industrial controllers, motor-control gateways, and connected sensor systems requiring several communications protocols.
The XMC4000 platform combines a 32-bit core with hardware peripherals for communication and control. Its 128 KB flash provides room for an embedded application, boot logic, and configuration data, while 20 KB of SRAM supports working memory and peripheral buffers. The 80 MHz clock rate allows the processor to service multiple interrupts and communication tasks, although final performance depends on peripheral configuration, memory latency, and the selected toolchain and operating system.
Typical uses include industrial communication controllers, CAN-to-serial gateways, LIN-based body and factory nodes, USB-to-fieldbus adapters, sensor-hub controllers, and compact motor-control modules. A 64-pin LQFP exposed-pad package also provides a conventional PCB footprint and a thermal pad for distributing heat through the board structure.
Designers should review the manufacturer pin-description table and electrical characteristics before assigning analog, communications, debug, clock, and power pins. Decoupling, exposed-pad soldering, clock stability, unused-pin treatment, and startup configuration must follow the XMC4100/XMC4200 datasheet and reference manual.
This product page combines the exact ordering-code characteristics with an application-focused selection guide, interface recommendations, comparison parameters, and practical PCB guidance. These engineering-oriented details help teams evaluate the XMC4100F64K128ABXQSA1 without reducing the selection decision to processor speed and flash memory alone.
Bộ thay thế dễ dàng lắp đặt cho XMC4100F64K128ABXQSA1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với XMC4100F64K128ABXQSA1 (cùng hình factor và footprint) — khác nhau ở Flash Memory, Package, Core Count, Product Type, Supply Voltage.
XMC4104F64K128ABXQSA1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →XMC4100F64K128ABXQSA1 Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit industrial microcontroller |
| Processor Core | Arm Cortex-M4 |
| CPU Architecture | 32-bit RISC |
| Maximum CPU Frequency | 80 MHz |
| Flash Memory | 128 KB (128K x 8) |
| SRAM | 20 KB |
| Core Count | 1 core |
| Operating Supply | 3.3 V |
| Internal Operating Range | 1.3 V to 3.3 V |
| Hộp | PG-LQFP-64-19 with exposed pad |
| Số chân | 64 pins |
| Temperature Grade | Industrial |
| CAN Interface | Yes |
| I2C Interface | Yes |
| LIN Interface | Yes |
| SPI Interface | Yes |
| UART/USART Interface | Yes |
| USB Interface | Yes |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân XMC4100F64K128ABXQSA1 pg-lqfp-64-19 with exposed pad
Cấu hình chân cho XMC4100F64K128ABXQSA1 (pg-lqfp-64-19 with exposed pad gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho XMC4100F64K128ABXQSA1.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
XMC4100F64K128ABXQSA1 phù hợp cho 6 Áp dụngs: Industrial CAN Gateway, USB-to-Fieldbus Adapter, LIN Sensor Hub, Industrial Sensor Controller, Compact Motor-Control Module, Data Acquisition and Monitoring.
Industrial CAN Gateway
The XMC4100F64K128ABXQSA1 fits an industrial CAN gateway because its 80 MHz Arm Cortex-M4 core can supervise communication tasks while its 128 KB flash and 20 KB SRAM support protocol conversion, local buffering, diagnostics, and configuration storage. The integrated CAN interface reduces the need for a separate controller in compact gateway designs. Place the MCU and transceiver on a controlled communications board, provide interface protection, and validate termination, isolation, and grounding for the target industrial environment.
Được đề xuất
USB-to-Fieldbus Adapter
The XMC4100F64K128ABXQSA1 is well suited to a USB-to-fieldbus adapter because it combines USB, CAN, SPI, UART/USART, I2C, and LIN connectivity with an 80 MHz 32-bit processor. Firmware can maintain a USB control channel while polling sensors and forwarding data over a selected fieldbus. Use the 20 KB SRAM for transient protocol buffers and the 128 KB flash for firmware, descriptors, and configuration, while separating sensitive analog and communications routing.
Được đề xuất
LIN Sensor Hub
A LIN sensor hub benefits from the XMC4100F64K128ABXQSA1 because its integrated LIN and I2C interfaces allow a controller to aggregate low-speed automotive-style sensors and communicate results through CAN, UART, or USB. The 80 MHz Cortex-M4 core has ample instruction throughput for scheduling multiple LIN tasks, diagnostics, and data filtering. Confirm the target transceiver requirements, logic levels, bus termination, and wake-up behavior before finalizing the hardware architecture.
Được đề xuất
Industrial Sensor Controller
The XMC4100F64K128ABXQSA1 can serve as the central controller for an industrial sensor node using its 80 MHz processing speed, 128 KB program memory, and 20 KB SRAM. SPI and I2C provide access to sensors and memory devices, while CAN or UART connects the node to a supervisory controller. Validate sensor timing, interrupt latency, input thresholds, and calibration storage against the electrical characteristics in the manufacturer datasheet.
Được đề xuất
Compact Motor-Control Module
The XMC4100F64K128ABXQSA1 is suitable for compact motor-control modules that require deterministic real-time processing alongside CAN, UART, and other serial interfaces. Its 80 MHz Cortex-M4 core can execute control loops and supervisory logic, while 128 KB flash accommodates application firmware and 20 KB SRAM supports control variables and communication buffers. The exact motor-control peripherals, PWM resources, analog inputs, and timing guarantees must be confirmed for the selected derivative.
Được đề xuất
Data Acquisition and Monitoring
The XMC4100F64K128ABXQSA1 supports data-acquisition and monitoring duties through its 80 MHz processing capacity, multiple serial interfaces, and 20 KB working memory. Firmware can sample configured inputs, timestamp events, filter results, and transfer records through USB, CAN, UART, or SPI. For reliable acquisition, verify analog-pin capabilities and acquisition timing in the pin and electrical tables, and isolate precision signals from switching and communication return currents.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho XMC4100F64K128ABXQSA1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | XMC4104F64K128ABXQSA1 |
|---|---|---|
| Package | PG-LQFP-64-19 with exposed pad | 64-pin LQFP exposed pad |
| Brand | Infineon Technologies | Infineon Technologies |
| Processor Core | Arm Cortex-M4 | Arm Cortex-M4 |
| CPU Frequency | 80 MHz | 80 MHz |
| Flash Memory | 128 KB | 128 KB |
| SRAM | 20 KB | 20 KB |
| Architecture | 32-bit single-core RISC | 32-bit single-core RISC |
| Supply Range | 1.3 V to 3.3 V | 1.3 V to 3.3 V |
| Communications Interfaces | CAN, I2C, LIN, SPI, UART/USART, USB | CAN, I2C, LIN, SPI, UART/USART, USB |
| Device Family | XMC4100 | XMC4104 |
Bảo phân biệt quan trọng
- Exact XMC4100-family ordering option (vsXMC4104F64K128ABXQSA1)
- Broad integrated communications support (vsXMC4104F64K128ABXQSA1)
- Industrial processing and memory balance (vsXMC4104F64K128ABXQSA1)
Ghi chú thiết kế
Route the exposed pad to a solid ground plane and use the manufacturer land pattern for the PG-LQFP-64-19 package. Thermal-via placement must preserve solderability and avoid pulling excess solder from the perimeter leads. Follow the package drawing for pad dimensions and keep high-current return paths away from sensitive sensor inputs.
Place the required bypass capacitors at the supply and ground pins using the shortest possible traces. Keep each decoupling loop compact so switching current returns through the capacitor rather than through long board traces. Verify capacitor voltage rating, DC-bias characteristics, and the power-supply sequencing requirements in the manufacturer electrical characteristics.
Assign communications and debug signals according to the alternate-function and pin-mux tables. Maintain controlled-impedance routing for USB, isolate noisy communication returns from analog references, and reserve test points for clock, reset, boot configuration, and debug access. Check the exposed pad and all unused-pin requirements before releasing the PCB.
Do not assume that a matching package automatically makes every XMC4000 derivative interchangeable. Before approving XMC4104F64K128ABXQSA1 as a replacement, compare peripheral availability, clock configuration, analog functions, qualification, software support, startup behavior, and pin multiplexing against the XMC4100F64K128ABXQSA1 design requirements.
Thông tin tuân thủ
The manufacturer product information identifies this ordering code as an industrial microcontroller rather than an AEC-Q100-qualified automotive device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer.
