產品(42,000+)

OPA2137U - Dual 36V 1MHz J-FET Op Amp | Texas Instruments
OPA2137U

OPA2137U - Dual 36V 1MHz J-FET Op Amp | Texas Instruments

The Texas Instruments OPA2137U is a dual J-FET-input operational amplifier with 1 MHz gain-bandwidth product, 3.5 V/µs slew rate, and a 36 V maximum total supply rating, housed in an 8-pin SOIC package. Both amplifiers provide low input bias current of ±10 pA, a quiescent current of 120 µA per channel, and an open-loop gain of 145 dB. A J-FET-input operational amplifier is a voltage-amplifier device whose field-effect transistor input stage provides very low input bias current. Within the broader semiconductor hierarchy, the OPA2137U belongs to the operational-amplifier family of analog ICs and supports low-impedance sensing, precision feedback networks, signal conditioning, and general-purpose analog signal paths. Unlike bipolar-input amplifiers, its J-FET inputs place minimal DC current on high-impedance sources. The OPA2137 series is designed for low-cost and miniature applications. Important characteristics include a ±10 pA input bias current, 120 µA per channel of quiescent current, and 145 dB open-loop gain. The dual configuration provides two amplifiers in one package while maintaining identical performance between channels, making it convenient for differential, active-filter, instrumentation, and buffer circuits. The device operates across a total supply range of ±2.25 V to ±18 V, equivalent to 4.5 V to 36 V across the supply terminals. Its 1 MHz gain-bandwidth product and 3.5 V/µs slew rate provide useful bandwidth for audio-frequency and low-frequency instrumentation applications. The input common-mode range includes the positive supply, allowing the amplifier to operate from a single supply when appropriately configured. Typical applications include low-level signal conditioning, buffered sensor outputs, audio preamplification, active filters, sample-and-hold circuitry, and precision analog measurement systems. The low bias current is particularly valuable when driving high-impedance detectors, transducers, or measurement nodes, while the low per-channel quiescent current supports compact and power-sensitive instruments. Designers should verify the complete input and output common-mode ranges, input bias-current behavior, output swing, and stability requirements against the manufacturer datasheet for the selected supply and load conditions. Decoupling capacitors should be placed close to the supply pins, and sensitive input nodes should use short traces, guarded routing, and a clean ground reference to minimize leakage and interference. This page combines manufacturer specifications, package and lifecycle information, drop-in replacement candidates, application guidance, and engineering design notes. It is intended to help designers compare the OPA2137U with same-footprint alternatives while selecting a part that matches the required bandwidth, supply voltage, input impedance, and environmental conditions.

詢價 聯絡我們
OPA2170AIDCUR - 36V Dual Op Amp, Rail-to-Rail Output, VSSOP-8 | Texas Instruments
OPA2170AIDCUR

OPA2170AIDCUR - 36V Dual Op Amp, Rail-to-Rail Output, VSSOP-8 | Texas Instruments

The Texas Instruments OPA2170AIDCUR is a dual-channel, 36 V, single-supply, low-power operational amplifier in a VSSOP-8 (DCU) micro-package, featuring rail-to-rail output swing, 1.2 MHz gain-bandwidth product, and 0.4 V/us slew rate for general-purpose analog signal conditioning. Each channel delivers a low offset voltage and low offset drift while consuming only 110 uA per channel of quiescent current, making this op amp suitable for battery-powered and always-on sensor interfaces. An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output, forming the fundamental building block of analog signal chains. It belongs to the broader category of linear integrated circuits within power management and analog signal conditioning, and is used for amplification, filtering, level shifting, buffering, and comparator functions. The OPA2170AIDCUR is part of TI's OPAx170 value-line family, alongside the single-channel OPA170 and quad-channel OPA4170, all sharing identical specifications to simplify design reuse across channel densities. The OPAx170 architecture operates from a single 2.7 V to 36 V supply (or dual ±1.35 V to ±18 V), eliminating the need for negative rails in single-supply systems. Key differentiating features include 19 nV/√Hz input voltage noise density, RFI-filtered inputs to reject out-of-band RF interference, and an input common-mode range that extends to the negative supply rail, which is critical for ground-referenced single-supply sensing. The device also includes internal ESD protection on the inputs and outputs, simplifying board-level robustness. Combined, these features enable precision measurement in noisy industrial environments. Typical applications include transducer signal conditioning for bridge sensors, temperature sensor interfaces (thermocouples, RTDs, thermistors), active filtering for audio and instrumentation, low-side current sensing, and portable medical or test equipment. The 36 V supply tolerance also supports 24 V industrial bus interfaces and automotive load-dump-protected rails. When designing with this part, place a 0.1 uF decoupling capacitor as close as possible to the V+ pin, and use a low-ESR ceramic at the supply. For unity-gain buffer or low-gain stages, a 10 nF to 100 nF compensation capacitor between V+ and the output node may improve capacitive load drive. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found on the manufacturer datasheet cover page.

詢價 聯絡我們
OPA2170AIDGK - 36V Dual Op Amp, RRO, 1.2MHz | Texas Instruments
OPA2170AIDGK

OPA2170AIDGK - 36V Dual Op Amp, RRO, 1.2MHz | Texas Instruments

The Texas Instruments OPA2170AIDGK is a dual-channel, 36V, single-supply, low-power operational amplifier (op amp) housed in an 8-pin MSOP/VSSOP package (DGK). It delivers a 1.2 MHz gain-bandwidth product, a 0.4 V/us slew rate, and a low 19 nV/sqrt(Hz) input-referred voltage noise density while drawing only 110 uA of quiescent current per channel. The device operates from 2.7V to 36V single supply (or +/-1.35V to +/-18V dual supply), making it well-suited to industrial 24V rails as well as 3.3V / 5V low-voltage analog signal chains. An operational amplifier (op amp) is a high-gain differential voltage amplifier that uses external feedback components to set closed-loop gain, bandwidth, and transfer function. Op amps are fundamental building blocks in analog signal conditioning: they amplify, buffer, filter, sum, and convert signals. Within the broader hierarchy, a dual low-power op amp like the OPA2170 sits below the "linear IC" family, adjacent to instrumentation amplifiers, comparators, and programmable gain amplifiers. The "value line" label from TI indicates it is positioned for cost-sensitive, high-volume designs without sacrificing key specs. Key features of the OPA2170 include 0.0035 uA input bias current (CMOS input stage), 120 dB CMRR, rail-to-rail output (RRO), an input common-mode range that includes the negative rail, and EMI/RFI filtered inputs to improve immunity in harsh electrical environments. The unity-gain-stable design requires no external compensation and supports capacitive loads up to 1 nF. Architecturally, the OPA2170 uses a CMOS input stage for high input impedance and low bias current, combined with a class AB output stage that achieves rail-to-rail swing on a single supply. This combination makes the part equally suitable for low-voltage sensor signal chains (where input bias current matters) and higher-voltage industrial loops (where supply tolerance matters). Typical applications include transducer signal conditioning, 4-20 mA loop drivers, low-side current sensing, active filters, audio signal buffering, general-purpose amplification in PLC analog input modules, and battery-powered instrumentation that needs wide supply tolerance. When designing in the OPA2170AIDGK, be mindful that although the inputs include the negative rail, the inputs do NOT include the positive rail - common-mode voltage must remain at least a few hundred mV below V+ for linear operation. Use the dual-channel part when two related signals (e.g., a differential sensor) need matched amplifier paths; switch to the quad-channel OPA4170 only when the PCB area savings of one IC outweigh the loss of channel-level routing flexibility. This page synthesizes distributor pricing, verified cross-reference alternatives in the same VSSOP-8 footprint, and practical design considerations not found in the manufacturer datasheet alone.

詢價 聯絡我們
OPA2171AIDR - Dual 36V 3MHz Low-Power Op Amp | Texas Instruments
OPA2171AIDR

OPA2171AIDR - Dual 36V 3MHz Low-Power Op Amp | Texas Instruments

The Texas Instruments OPA2171AIDR is a dual-channel, 36V, 3MHz, low-power operational amplifier in an 8-pin SOIC package. The OPA2171AIDR is part of the OPAx171 family (single/dual/quad) and is designed for single-supply operation from 2.7V (±1.35V) to 36V (±18V). It features rail-to-rail output (RRO), low offset voltage, low drift, and low quiescent current, making it well-suited for cost-sensitive general-purpose analog signal conditioning. An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output. It is the fundamental building block of analog signal chains, used for amplification, filtering, comparison, buffering, and mathematical operations. The OPA2171 belongs to the lineage of low-power, general-purpose amplifiers, sitting between precision op amps (high accuracy, high power) and high-speed op amps (wide bandwidth, higher noise), optimized for applications requiring moderate bandwidth and low current draw. Key features of the OPA2171AIDR include 3MHz gain-bandwidth product, 1.5V/µs slew rate, low quiescent current, rail-to-rail output swing, and 36V maximum supply voltage. The 3MHz gain-bandwidth product enables stable operation in active filter circuits, sensor signal conditioning, and transducer amplification. The wide supply range supports industrial 24V bus systems, automotive 12V rails (post-protection), and battery-powered portable equipment operating down to 2.7V. The OPA2171 uses a CMOS input stage for low input bias current, paired with a rail-to-rail output stage that maximizes dynamic range on low-voltage supplies. Internal EMI/RFI filtering on the inputs improves robustness in harsh electrical environments. The dual op-amp configuration in the SOIC-8 package provides two independent amplifiers in a small footprint, enabling compact multi-channel designs. Typical applications include transducer amplification, sensor signal conditioning, industrial process control, battery-powered instrumentation, active filters, and voltage reference buffers. The wide input range allows direct interfacing with 24V industrial sensors, while the rail-to-rail output maximizes dynamic range on 3.3V or 5V ADC rails. When designing with this device, pay attention to input common-mode range, especially near the negative rail where CMOS input stages exhibit degraded behavior. Decouple supply pins with 0.1µF ceramic capacitors placed close to the IC. This page synthesizes distributor pricing, drop-in alternatives (including same-brand OPA2171AID and OPA4171 variants), and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
OPA2172 - 36V 10MHz Dual Rail-to-Rail Op Amp | Texas Instruments
OPA2172

OPA2172 - 36V 10MHz Dual Rail-to-Rail Op Amp | Texas Instruments

The Texas Instruments OPA2172 is a dual, 36-V, 10-MHz, rail-to-rail output (RRO) operational amplifier in an 8-pin SOIC (D) package. It operates on supplies from +4.5 V (±2.25 V) to +36 V (±18 V), combining wide dynamic range with low power consumption of 1.6 mA per amplifier. An operational amplifier (op amp) is a high-gain differential voltage amplifier used as the building block of analog signal chains - a subcategory of amplifier ICs within the broader power-management and signal-conditioning hierarchy. The OPA2172 belongs to TI's OPAx172 family (OPA172 single, OPA2172 dual, OPA4172 quad), which is engineered for high-voltage, single-supply designs where the output must swing close to the rails. Key features include a gain-bandwidth product of 10 MHz, low input offset voltage of ±0.2 mV, and ultra-low offset drift of ±0.3 uV/degC, ensuring accuracy across the industrial temperature range. Input bias current is a low ±8 pA thanks to the JFET-input front end, and broadband noise is 7 nV/rtHz, making the part suitable for precision, low-noise signal conditioning. High slew rate supports fast settling in active filters and ADC drivers. Architecturally, the OPA2172 uses a precision input stage with rail-to-rail output stage that maintains low distortion even when driving loads near the supply rails. The 36-V tolerance provides headroom against industrial 24-V bus transients, and operation down to +4.5 V supports 5-V single-supply systems. Typical applications include 24-V industrial instrumentation front ends, active filter and data-acquisition signal conditioning ahead of ADCs such as the ADS131M08, sensor buffering, and output amplification in audio and synth-DIY circuits where it replaces noisier TL072-class devices. Design tip: keep total supply below 36 V, and for maximum output swing at low loads, ensure load impedance keeps output current within datasheet limits; bypass both supply pins with 100 nF ceramics placed close to the device.

詢價 聯絡我們
OPA2172 - Dual 36V 10MHz Low-Noise Op Amp | Texas Instruments
OPA2172ID

OPA2172 - Dual 36V 10MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments OPA2172ID is a dual, 36-V, 10-MHz, low-power rail-to-rail output operational amplifier in an 8-SOIC package, part of the OPAx172 family that also includes the single OPA172 and quad OPA4172. It operates on supplies from +4.5 V to +36 V (or ±2.25 V to ±18 V), making it versatile for single-supply and dual-supply industrial systems. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, and is a fundamental building block of analog signal conditioning, filtering, and amplification. The OPA2172 sits in the hierarchy of amplifiers -> operational amplifiers -> precision, rail-to-rail output amplifiers, balancing bandwidth, noise, and power in one general-purpose part. Key specifications include ±0.2 mV offset voltage, ±0.3 uV/C offset drift, 10 MHz gain-bandwidth product, ±8 pA input bias current, 1.6 mA quiescent current per amplifier, and 7 nV/√Hz broadband noise. The rail-to-rail output stage maximizes dynamic range in low-voltage designs, while the wide supply range supports industrial 24 V buses directly. The CMOS input stage provides high input impedance and picoampere bias currents suitable for high-impedance sensors and photodiode circuits. The output stage swings to within millivolts of the rails at light load and is stable with substantial capacitive loads, simplifying buffer designs. Low quiescent current permits use in battery-powered and thermally constrained equipment. Typical applications include motor-control current sensing, solar inverters, power-supply feedback loops, active filters, and audio signal chains, where low noise and high slew rate preserve signal fidelity. The dual channel saves board space versus two singles. Design tip: decouple supply pins with 0.1 uF ceramics close to the device, keep feedback resistors low-valued for best noise, and verify output swing headroom under heavy load.

詢價 聯絡我們
OPA2192IDGK - 36V Precision RRIO Op Amp Dual | TI
OPA2192IDGK

OPA2192IDGK - 36V Precision RRIO Op Amp Dual | TI

The Texas Instruments OPA2192IDGK is a dual-channel, 36-V precision operational amplifier with rail-to-rail input/output (RRIO), low offset voltage, and low input bias current, implemented in TI's e-trim chopper-stabilized architecture and packaged in an 8-pin MSOP (PowerPAD). It carries an automotive temperature grade and supports up to +/-18 V or 36 V single-supply operation from a 4.5 V to 36 V rail. Background: An operational amplifier (op amp) is a high-gain DC-coupled analog building block that uses external feedback to set gain, filter response, and signal conditioning behavior. The OPA2192IDGK belongs to the precision op-amp family, characterized by microvolt-level input offset voltage, picoampere-range input bias current, and low drift over temperature - a category that sits above general-purpose op amps and below zero-drift chopper amplifiers in the precision signal-chain hierarchy. Rail-to-rail input/output op amps accept and produce signals that swing to both supply rails, which maximizes dynamic range in low-voltage single-supply designs and is critical for driving successive-approximation ADCs without headroom loss. Key specifications include 5 pA typical input bias current, 25 uV maximum input offset voltage, 0.5 uV/degC typical offset drift, 10 MHz unity-gain bandwidth, and 20 V/us slew rate. The e-trim architecture provides 5 uV/degC offset drift without the chopping sidebands or large inrush currents of classic chopper amplifiers. EMI-hardened inputs reject RF interference from adjacent switching converters and motor drivers in industrial environments. The MSOP-8 package with PowerPAD delivers a thermal resistance of approximately 50 C/W, enabling dual-channel operation at full bandwidth without external heatsinking. Typical applications include precision weigh scales, sensor signal conditioning for thermocouples and strain gauges, battery management current sensing, and industrial analog input modules. Designers select the OPA2192IDGK for systems requiring sub-100 uV total DC accuracy across the full -40C to +125C automotive temperature range and tight PCB footprints where two precision channels must fit into a 3 mm x 3 mm outline. Designers should note the OPA2192IDGK is pin-compatible with the OPA2191 (lower precision), OPA2188 (zero-drift), and OPA2227 (lower precision), enabling drop-in upgrades. For optimal performance, bypass supplies with 0.1 uF ceramic capacitors placed within 5 mm of the V+ and V- pins. This page consolidates real-time distributor pricing, drop-in alternatives, and design notes beyond the manufacturer datasheet to accelerate part selection.

詢價 聯絡我們
OPA2192IDGKR - 36V Precision RRIO Dual Op Amp | Texas Instruments
OPA2192IDGKR

OPA2192IDGKR - 36V Precision RRIO Dual Op Amp | Texas Instruments

The Texas Instruments OPA2192IDGKR is a 36-V, precision, rail-to-rail input/output (RRIO), low-offset-voltage, low-input-bias-current operational amplifier with e-trim, delivered in an 8-pin VSSOP (DGK) package. Key headline parameters include 10-MHz unity-gain bandwidth, 20-V/µs slew rate, ±5-µV typical offset voltage, ±0.2-µV/°C typical offset drift, and 4.5-V to 36-V single-supply operation (or ±2.25-V to ±18-V dual). The e-trim calibration architecture trims input offset and offset drift at the wafer level, eliminating the need for external nulling components. An operational amplifier (op amp) is a high-gain DC-coupled analog circuit block that amplifies differential input voltages. The OPA2192 belongs to the precision amplifier sub-class, where DC accuracy (low offset, low drift) and rail-to-rail signal swing matter more than raw speed. It sits in the broader hierarchy of linear ICs -> amplifiers -> operational amplifiers -> precision RRIO op amps -> semiconductor, and competes with parts such as the ADA4522 and OPA2188. Its main role in a system is to condition small analog signals (sensor bridges, shunt currents, thermocouples) with minimal added error and to drive ADC reference or output stages up to the supply rails. Distinctive features include differential input-voltage range to the supply rail, high-output current drive with no phase reversal, low-input-bias current with e-trim, and integrated EMI/RFI rejection at 1 GHz. The OPA2192 also offers independent short-circuit protection on the outputs and a wide 4.5-V to 36-V supply headroom that lets a single device serve both 5-V analog rails and 24-V industrial transducers. Architecturally, the OPA2192 uses a bipolar input stage with chopper-free e-trim post-package calibration, preserving low noise while achieving 10-MHz GBW at 20 V/µs. The RRIO output stage swings within millivolts of either rail at moderate loads, eliminating headroom loss in low-voltage ADC interfaces and giving designers full dynamic range on 5-V or 12-V rails. Typical applications include precision analog input modules, 4-20 mA loop transmitters, multi-channel data acquisition front ends, test and measurement instruments, and active filtering in audio paths. Designers favor it where both 5-V digital-rail operation and 24-V industrial transducers must share one BOM line. When using the OPA2192, observe the maximum differential input-voltage limit and add an input-series resistor for true over-voltage protection; a 2-kΩ resistor on each input typically prevents fault-current damage during 36-V transients. This page also synthesizes distributor pricing, drop-in alternates, and practical design notes that the TI datasheet alone does not surface.

詢價 聯絡我們
OPA2192IDGKT - 36V Precision RRIO Op Amp, 10MHz, Dual | Texas Instruments
OPA2192IDGKT

OPA2192IDGKT - 36V Precision RRIO Op Amp, 10MHz, Dual | Texas Instruments

The Texas Instruments OPA2192IDGKT is a dual-channel, 36-V, e-trim precision operational amplifier that delivers rail-to-rail input and output (RRIO) swing, 10 MHz unity-gain bandwidth, and 20 V/µs slew rate in an 8-pin VSSOP (DGK) package. According to the manufacturer datasheet, the OPA2192 family offers typical input offset voltage of ±5 µV, offset drift of ±0.2 µV/°C, and a 1 mA per-channel quiescent supply current while supporting output current up to 65 mA per channel for direct drive of low-impedance loads. A precision operational amplifier (op amp) is a high-gain DC-coupled analog building block used to amplify small differential signals in instrumentation, signal conditioning, and active-filter chains. The OPA2192 belongs to the e-trim chopper-stabilized family that achieves CMOS-class input bias current with bipolar-class DC accuracy, positioning it above general-purpose op amps in the precision amplifier hierarchy: precision op amp -> operational amplifier -> analog IC -> signal chain -> semiconductor. Key features include differential input range that extends to both supply rails, integrated EMI/RFI rejection input filtering, and 6 V to 36 V single-supply operation (or ±3 V to ±18 V dual-supply). The e-trim process eliminates the traditional chopper chopping artifacts, making the part suitable for DC-coupled precision paths where chopper noise would otherwise be unacceptable. Architecture-wise, the OPA2192 combines a CMOS input differential pair with TI's e-trim calibration to correct residual input-referred offset at the wafer level. This achieves laser-trim performance without active chopping, providing clean DC behavior at low frequencies while still supporting the 10 MHz GBW required by audio and wide-bandwidth transducer signal conditioning. Typical applications include industrial process-control analog front ends, precision analog-input modules for PLCs, multi-channel data-acquisition (DAQ) signal conditioning, precision active filters, and transducer excitation/readout such as bridge amplifiers and RTD conditioners. The wide supply range allows direct interface to ±15 V industrial rails as well as 24 V loop-powered systems. When designing with this device, ensure that the input common-mode voltage stays within the rail-to-rail range (which includes both rails). Decouple the supply pins with a 100 nF ceramic capacitor placed within 5 mm of the device, and consider a 10 µF bulk capacitor for high-output-current transients. The exposed thermal pad (if present on the package variant) must be soldered to a copper pour for rated thermal performance. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes that go beyond the manufacturer datasheet, helping engineers shorten selection time and avoid common layout pitfalls.

詢價 聯絡我們
OPA2192IDR - 36V Precision RRIO Dual Op Amp e-Trim | TI
OPA2192IDR

OPA2192IDR - 36V Precision RRIO Dual Op Amp e-Trim | TI

The Texas Instruments OPA2192IDR is a dual-channel, 36V precision operational amplifier with rail-to-rail input and output (RRIO), delivered in an 8-pin SOIC (D) package rated from -40C to +125C. It combines low offset voltage, low input bias current, and TI e-trim calibration technology for outstanding DC precision in a cost-effective general-purpose amplifier. A precision operational amplifier is a type of analog amplifier IC designed to amplify small differential signals with minimal error, positioned within the hierarchy of op amps > precision amplifiers > analog front-end ICs > linear ICs. Unlike general-purpose op amps, precision amplifiers minimize input offset voltage, bias current, and drift so sensor and measurement signal chains remain accurate without external trimming. Key features include operation from 4.5V to 36V single supply (or +/-2.25V to +/-18V dual supply), a 10MHz gain-bandwidth product, and a 20V/us slew rate - a rare combination of DC precision and AC performance. The e-trim architecture achieves very low offset voltage without system-level trimming, while rail-to-rail inputs allow the common-mode range to extend to both supplies and rail-to-rail output maximizes dynamic range on low-voltage rails. Architecturally, the OPA2192 uses an input stage that seamlessly transitions between two differential pairs to maintain rail-to-rail common-mode operation, with e-trim calibration performed at wafer test to null residual offset. The low input bias current suits high-impedance sources, and low total harmonic distortion supports precision AC signal chains. Typical applications include industrial data acquisition front ends, transimpedance and sensor signal conditioning, precision active filters, and single-supply battery-powered instrumentation. The wide 36V supply rating also allows direct connection to industrial 24V rails with simple headroom management. Design tip: reference the input common-mode near mid-supply to minimize crossover distortion inherent in dual-pair input stages, and verify AC behavior near the rails in high-precision designs.

詢價 聯絡我們
OPA2206ADGKR - ±40V OVP Dual Precision Op Amp | Texas Instruments
OPA2206ADGKR

OPA2206ADGKR - ±40V OVP Dual Precision Op Amp | Texas Instruments

The Texas Instruments OPA2206ADGKR is a dual-channel, input-overvoltage-protected (OVP) precision operational amplifier housed in an 8-pin VSSOP (DGK) package, with integrated input protection up to ±40 V beyond the supplies, an input offset voltage of 4 µV (typical) / 25 µV (maximum), an input offset voltage drift of ±0.08 µV/°C (typical), and an input bias current of ±5 pA (typical) via super-beta input transistors. An operational amplifier (op amp) is a DC-coupled high-gain electronic voltage amplifier with differential inputs and, typically, a single-ended output. Precision op amps form a distinct sub-category characterized by very low offset voltage, low offset drift, low bias current, and low noise, sitting hierarchically under amplifier ICs (integrated circuits) and analog signal-chain components. The OPA2206 is the dual-channel member of TI's OPAx206 family and represents the next-generation evolution of the long-standing OPAx277 series, retaining the OPAx277's low-noise, low-drift e-trim™ precision architecture while adding integrated ±40 V input OVP, eliminating the need for external input clamping in many industrial designs. Key features include 4 µV (typ) / 25 µV (max) offset voltage achieved via TI's proprietary e-trim™ trimming technology, ±0.08 µV/°C (typ) offset drift, ±5 pA (typ) input bias current enabled by super-beta input transistors, integrated ±40 V input OVP that survives ESD and transients beyond the rails, and a wide supply range of 4.5 V to 36 V (single supply) or ±2.25 V to ±18 V (dual supply). The device is specified over the −40 °C to +125 °C industrial temperature range. Architecturally, the OPA2206 uses a bipolar e-trim™ process with super-beta input stages, which decouple bias current from base current, dramatically reducing input bias current while preserving the low-noise and low-drift characteristics of a precision bipolar op amp. The e-trim™ trim step digitally calibrates each die's offset to <25 µV at room temperature and minimizes drift across temperature. Typical applications include industrial process-control analog input modules, precision sensor signal conditioning (load cells, strain gauges, thermocouple front-ends), test and measurement equipment, battery monitoring systems, and any high-voltage-tolerant precision front-end where input transients or wiring faults could otherwise destroy a conventional op amp. The wide supply and ±40 V OVP make it a strong fit for 24-V industrial-bus sensor interfaces. When designing with this device, place the input series resistors as close to the OPA2206 inputs as possible to maximize the effectiveness of the integrated OVP clamp structure and to limit fault current through the ESD diodes. The OPA2206 does not include rail-to-rail output; output swing is typically within ~1 V of each rail at 10 kΩ load. This page synthesizes distributor pricing, drop-in alternatives in the VSSOP-8 footprint, and practical design notes that are not found in the manufacturer datasheet alone.

詢價 聯絡我們
OPA2227P - Dual Precision Low-Noise Op Amp | Texas Instruments
OPA2227P

OPA2227P - Dual Precision Low-Noise Op Amp | Texas Instruments

Texas Instruments OPA2227P is a dual high-precision, low-noise operational amplifier with two amplifier circuits in an 8-pin PDIP package. Its stated characteristics include 3 nV/√Hz noise, 10 V/µs slew rate, 5 µs settling time, and 138 dB common-mode rejection, making it suitable for precision DC and AC signal conditioning. The device is specified for operation from -40°C to +85°C. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. Its place in the signal-chain hierarchy is operational amplifier → analog IC → semiconductor, while precision operation refers to maintaining accurate DC gain and offset behavior as well as low-distortion AC performance. The dual configuration provides two amplifiers in one package, reducing board area compared with two separate single-channel devices. The OPA2227P combines low noise with wide bandwidth and high precision. The 3 nV/√Hz noise figure makes it relevant to sensor signals, instrumentation amplifiers, audio paths, and other applications in which input-referred noise limits usable resolution. Its 138 dB CMRR helps reject common-mode interference, while the 10 V/µs slew rate and 5 µs settling characteristics support faster closed-loop signal transitions than precision amplifiers with narrower bandwidth. OPA2227 and OPA228 devices are identified by Texas Instruments as pin-for-pin replacements for industry-standard OP27 and OP37 devices. The OPA2227P therefore supports legacy precision-amplifier designs while offering a dual-channel implementation. Its internal characteristics are suited to both DC measurement and AC-coupled applications where low noise, stable gain, and common-mode rejection are important. Typical uses include precision measurement front ends, low-level sensor amplifiers, buffered analog outputs, laboratory instrumentation, audio equipment, and active analog filters. The PDIP-8 package is suited to through-hole prototyping and designs where a mechanically robust package and readily visible connections are useful. Board-level compatibility still requires verification of supply voltage, input common-mode range, output swing, and stability configuration. Design with the manufacturer datasheet as the controlling reference for maximum supply voltage, input bias current, offset voltage, open-loop gain, output-current capability, and recommended compensation. Place a short, low-impedance return from the power-supply pins to the ground plane, and provide adequate bypass capacitance close to the device. Avoid placing long copper traces beside sensitive input nets, and confirm that the selected gain and feedback network remain stable at the intended frequency. This product record combines manufacturer ordering information, device-family positioning, precision and noise characteristics, practical application guidance, and drop-in replacement analysis. It helps engineers distinguish the PDIP OPA2227P from related single, dual, quad, and alternate-family variants before committing a PCB footprint or production release.

詢價 聯絡我們
OPA2237EA/2K5 - Dual 1.5MHz Op Amp, 750µV Offset | TI
OPA2237EA/2K5

OPA2237EA/2K5 - Dual 1.5MHz Op Amp, 750µV Offset | TI

The Texas Instruments OPA2237EA/2K5 is a dual-channel, single-supply operational amplifier from TI's MicroAmplifier™ Series, offering 1.5 MHz bandwidth and 0.5 V/µs slew rate in an 8-pin MSOP/VSSOP package. The device features a maximum offset voltage of 750 µV, a low quiescent current of 350 µA per channel maximum, and operates from a wide supply range of +2.7V to +36V single supply (±1.35V to ±18V dual supply). The tape-and-reel /2K5 suffix indicates a 2,500-unit reel packaging for high-volume SMT assembly. A dual operational amplifier (op amp) is a single integrated circuit that contains two independent op-amp cells sharing common power pins; it is a member of the broader linear IC hierarchy that includes op amps -> amplifiers -> signal conditioning ICs -> analog ICs -> semiconductors. The OPA2237's dual configuration saves PCB area versus two single op amps while keeping channel-to-channel matching tight for instrumentation paths. Key features include low input bias current (~20 nA), wide bandwidth suitable for active filters and audio preamplifiers, and MicroAmplifier-series miniaturization that targets space-limited portable designs. The 750 µV maximum offset makes the part accurate enough for sensor signal conditioning without external trimming, while the 350 µA quiescent current keeps battery drain modest. Architecturally, the OPA2237 uses a bipolar input stage optimized for low-offset single-supply operation, with internal compensation that stabilizes the part at unity gain. The wide supply range (±18V or +36V single-supply) lets one part cover both low-voltage battery and higher-voltage industrial signal chains. Typical applications include battery-powered instrumentation, PCMCIA cards, portable medical devices, transducer amplifiers, and general-purpose signal conditioning in industrial and consumer designs. The MSOP-8 footprint is footprint-compatible with the SOIC-8 OPA2237UA variant for layout reuse. When designing with this op amp, observe the input common-mode range that includes the negative rail (true single-supply operation) and use a low-impedance ground return to keep offset drift under temperature. Add an output resistor if driving capacitive loads above 1 nF to maintain phase margin. This page synthesizes verified distributor pricing, drop-in alternatives, comparison data, and engineering design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
OPA2277P - 10µV Precision Dual Op Amp | Texas Instruments
OPA2277P

OPA2277P - 10µV Precision Dual Op Amp | Texas Instruments

Texas Instruments OPA2277P is a dual-circuit, high-precision, low-power operational amplifier offering 10 µV offset voltage and 0.1 µV/°C offset drift in an 8-pin PDIP package. Designed as an upgrade to the industry-standard OP-177, the OPAx277 family combines improved noise performance, a wider output-voltage swing, twice the speed, and half the quiescent current of that established precision-amplifier reference. An operational amplifier is a voltage-controlled differential amplifier whose inverting and non-inverting inputs determine the gain and output behavior of an analog signal chain. The precision operational-amplifier category sits between general-purpose amplifiers and application-specific signal-conditioning ICs. It is part of the broader amplifier hierarchy and supports instrumentation, sensor measurement, control, conversion, and reference-buffer circuits where low offset, low drift, bias-current control, and power-supply rejection are important. The OPA2277P’s 10 µV offset and 0.1 µV/°C drift are the principal precision specifications. These characteristics reduce output error in high-gain circuits, particularly when small sensor signals are amplified over a wide temperature range. Low bias current supports high-impedance sources, while high common-mode rejection and high power-supply rejection improve immunity to signals shared by both inputs and to disturbances originating from the supply rails. The device contains two amplifier channels in one package. Its improved noise and wider output swing make it useful in precision integrators, low-level signal conditioners, measurement systems, and analog control loops. The low quiescent current also suits battery-operated and compact industrial equipment where each milliamp of supply demand can affect the achievable operating duration. The two-channel package reduces component count when the signal chain needs matched functional channels. OPA2277P is offered in the 8-pin PDIP package, making it suitable for through-hole assembly and legacy industrial or instrumentation platforms that do not require a surface-mount package. Designers should preserve the polarity of the differential inputs, avoid exceeding the power-supply ratings, and provide suitable bypassing at the supply pins. Stable operation also depends on maintaining the required output-load conditions and preventing excessive output saturation. This product summary combines the manufacturer’s device description with practical selection guidance for engineers evaluating precision signal chains. It distinguishes the OPA2277P from lead-free ordering variants, identifies the package and pin assignments, and explains where offset, drift, bias current, noise, and supply rejection matter. Current commercial availability, lead time, and a formal quote should be handled through XAIPART’s Request a Quote form rather than static pricing information.

詢價 聯絡我們
OPA2277UA - 10µV Dual Precision Op Amp | Texas Instruments
OPA2277UA

OPA2277UA - 10µV Dual Precision Op Amp | Texas Instruments

The Texas Instruments OPA2277UA is a dual-channel, high-precision, low-power operational amplifier supplied in an 8-pin SOIC (D-package) that replaces the legacy OP-177 with substantially better noise, wider output swing, twice the speed, and half the quiescent current. The OPA2277UA delivers an ultra-low input offset voltage of 10 µV (max), an ultra-low offset drift of ±0.1 µV/°C, an open-loop gain of 134 dB, common-mode rejection of 140 dB, and high power-supply rejection while drawing only 800 µA of quiescent current per channel. It is specified for ±2 V to ±18 V supplies, swings to within 1 V of each rail on a ±15 V supply, and operates across the -40°C to +125°C industrial temperature range. Background knowledge: A precision op-amp (operational amplifier) is a high-gain DC-coupled analog building block whose input offset voltage, offset drift, bias current, and noise are engineered to far tighter limits than those of a general-purpose op-amp. Within the signal-chain hierarchy, the OPA2277 sits in the "precision" tier between general-purpose amplifiers (e.g. OPA234) and zero-dr chopper-stabilized amplifiers (e.g. OPA2188), drawing meaningfully lower bias current than old bipolar parts (e.g. OP-27) while delivering lower voltage noise than early CMOS parts (e.g. TLC2277). It is functionally a "dual, improved OP-177" intended for bridge amplifiers, strain gauges, thermocouple conditioning, and precision active filters where µV-level DC accuracy must be preserved across -40°C to +125°C. Architecturally, the OPA2277 uses a bipolar transistor input stage with laser-trimmed thin-film resistors, a complementary bipolar output stage capable of driving 2 kΩ loads, and internal compensation that removes the need for an external compensation capacitor. The result is a stable unity-gain device that does not oscillate when used as a buffer, with a gain-bandwidth product of 1 MHz and a 2 V/µs slew rate that supports audio-bandwidth signal conditioning, 16-bit ADC input buffers, and reference-voltage buffers. Typical applications include precision weighing scales and load-cell signal chains (where 10 µV Vos preserves mV-level bridge outputs), industrial process-control 4-20 mA loop transmitters, medical instrumentation front-ends, precision active filters, multi-channel data-acquisition multiplexed front ends, and reference-voltage buffers for 16-bit and 18-bit ADCs. The wide supply range also allows use in ±15 V legacy industrial backplanes. A practical design consideration: although the OPA2277 is unity-gain stable, its 1 MHz GBW means it is best used for DC-accurate low-frequency applications (sub-100 kHz). For higher-bandwidth precision needs, the OPA2227 (same package, 13 MHz GBW) or OPA2156 (pin-compatible, lower noise) are better choices; choose this part when DC accuracy and price dominate over bandwidth. This page synthesizes distributor stock and pricing, AEO-optimized FAQ, and drop-in alternatives that complement the manufacturer datasheet.

詢價 聯絡我們
OPA227P - 8MHz, 36V Low-Noise Op Amp | Texas Instruments
OPA227P

OPA227P - 8MHz, 36V Low-Noise Op Amp | Texas Instruments

The Texas Instruments OPA227P is a single, high-precision operational amplifier with 8 MHz gain-bandwidth product, 2.3 V/µs slew rate, and operation from ±2.5 V to ±18 V in an 8-pin PDIP package. According to the manufacturer product page, the OPA227 family is designed for low noise and low offset voltage applications. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between two input voltages. Within the broader semiconductor hierarchy, this precision operational amplifier belongs to analog signal-chain ICs used for instrumentation, buffering, current-to-voltage conversion, filtering, and low-level sensor amplification. The verified OPA227 family data identifies 8 MHz bandwidth and 2.3 V/µs slew rate, combining useful AC performance with precision DC operation. Its ±2.5 V to ±18 V supply capability permits bipolar rails within the stated range and supports single-supply operation when configured appropriately. The OPA227P uses the same dual-lead 8-pin PDIP form associated with OPA227U. OPA227 is positioned for applications requiring both AC and precision DC performance. Key selection considerations include noise, input offset voltage, common-mode range, output swing, supply voltage, stability with the selected feedback network, and the system noise gain. The P suffix identifies a PDIP package, while the U suffix identifies the surface-mount SOIC option. Typical uses include precision bridge and transducer interfaces, low-level signal conditioning, buffered analog outputs, active filters, laboratory instrumentation, and power-supply feedback loops. In each circuit, the amplifier must remain stable at the intended closed-loop gain and operate without input or output saturation. PCB design should preserve the integrity of high-impedance feedback nodes by keeping input and feedback traces short and minimizing parasitic capacitance. Bypass each supply connection close to the amplifier with suitable decoupling, and route return currents directly to the ground reference rather than through shared copper paths. This page combines the verified Texas Instruments product information with practical package, selection, sourcing, and design guidance. Exact offset, noise-density, input-bias-current, common-mode, output-swing, and temperature values require the manufacturer datasheet because they were not supplied in the verified search data.

詢價 聯絡我們
OPA227PA - Low-Noise Precision Op Amp | Texas Instruments
OPA227PA

OPA227PA - Low-Noise Precision Op Amp | Texas Instruments

Texas Instruments OPA227PA is a single-circuit, high-precision operational amplifier optimized for low-noise and low-offset-voltage signal conditioning. The device provides 3 nV/√Hz noise density, a 10 V/µs slew rate, 5 µs settling time, and 138 dB common-mode rejection according to the manufacturer documentation. It is supplied in an 8-pin PDIP package and is specified for operation from -40 °C to 85 °C. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while using negative feedback to control gain, bandwidth, and output behavior. Within the broader semiconductor hierarchy, OPA227PA is a precision operational amplifier, a linear amplifier and signal-conditioning IC. This category is used in instrumentation, sensor interfaces, laboratory equipment, audio electronics, and precision analog systems where low noise and small input-offset errors influence measurement accuracy. The OPA227PA combines a 10 µV input-offset voltage with 3 nV/√Hz noise density and a 10 V/µs slew rate. Its 138 dB CMRR indicates strong rejection of common-mode signals, while the 5 µs settling specification supports accurate operation after rapid input or output transitions. The 18 V maximum supply voltage cited in product data provides a useful operating limit for conventional bipolar or dual-supply analog designs. Texas Instruments describes the OPAx227 family as a pin-for-pin replacement for the industry-standard OP27 and OP37, with substantial performance improvements. This relationship makes pin compatibility an important design consideration when replacing older precision amplifiers. Because the OPA227PA is a single-amplifier version, board designers should confirm the exact pin functions in the manufacturer datasheet before modifying a board that originally carried a different package or channel configuration. Typical applications include precision sensor amplifiers, low-level current-to-voltage converters, laboratory measurement front ends, audio preamplifiers, and buffered analog signal chains. In each case, the low 3 nV/√Hz noise density reduces the input-referred noise contribution, while the 10 µV offset specification limits signal-chain error near the zero-input operating point. The 8-pin PDIP package also facilitates prototyping, socketed assemblies, and through-hole industrial equipment. For stable operation, place input and feedback components close to the amplifier pins, maintain the required bypass-capacitor arrangement, and avoid long PCB traces in high-gain feedback loops. Input and output voltages must remain within the device's common-mode and supply limits. Stable operation also depends on maintaining adequate phase margin with the selected gain and load, particularly when driving capacitive loads or operating at high closed-loop gain. This product page consolidates the manufacturer specifications, package details, application guidance, drop-in replacement context, and practical design notes needed to evaluate OPA227PA. It also distinguishes direct footprint compatibility from broader functional similarity, helping engineers identify the correct replacement while protecting signal-integrity and measurement performance.

詢價 聯絡我們
OPA227U - High Precision Low Noise Op Amp | Texas Instruments
OPA227U

OPA227U - High Precision Low Noise Op Amp | Texas Instruments

The Texas Instruments OPA227U is a high-precision, low-noise operational amplifier that combines wide bandwidth with excellent DC precision in an 8-pin SOIC package. It features 3 nV/sqrt(Hz) input voltage noise density, 2.3 V/us slew rate, 8 MHz unity-gain bandwidth, and 138 dB open-loop CMRR, making it suitable for both precision DC and wideband AC signal conditioning. The OPA227U is unity-gain stable, with 5 us settling time to 0.1% and 75 uV maximum offset voltage, addressing the demanding requirements of instrumentation, audio, and data acquisition front-ends. An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output. Within the broader analog semiconductor taxonomy, an op amp belongs to the linear IC family, and the precision op amp sub-category is further characterized by ultra-low offset voltage, low drift, low bias current, and high common-mode rejection ratio (CMRR). The OPA227U occupies a position above general-purpose op amps (such as the LM358) and below chopper-stabilized amplifiers, targeting applications that require both AC fidelity and DC accuracy in a single device. The OPA227U is built on a complementary bipolar process that delivers 5 us settling time to 16-bit accuracy, a substantial improvement over legacy OP-27 and OP-177 designs. Its 10 nA maximum input bias current, 138 dB minimum CMRR, and 160 dB minimum open-loop gain enable the device to maintain precision across wide common-mode and temperature ranges. Single, dual, and quad channel versions (OPA227, OPA2227, OPA4227) share the same internal compensation and pinout, allowing portable designs to scale channels without redesign. Typical applications include precision instrumentation, active filters, data acquisition systems, professional audio equipment, and test & measurement front-ends. The combination of low noise and high DC accuracy makes the OPA227U particularly well-suited for 16-bit and 18-bit ADC driver circuits, weigh scales, thermocouple amplifiers, and medical instrumentation. Operating from +/-2.5 V to +/-18 V dual supplies or 5 V to 36 V single supply, the device adapts to industrial and battery-powered designs. When designing with the OPA227U, observe standard precision op-amp practices: keep input traces short and guarded to preserve CMRR, place a 1 nF to 10 nF ceramic bypass capacitor close to the supply pins, and use low-thermal-EMF PCB materials for high-gain stages. A 100 ohm series output resistor isolates the amplifier from capacitive loads greater than 1 nF to prevent ringing. The OPA227U is a direct upgrade path for legacy OP-27 designs, providing a quieter, wider-bandwidth, lower-distortion alternative in the same SOIC-8 footprint. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes for the OPA227U. The information below is curated for engineers evaluating the part for new designs, second-source qualification, or legacy OP-27/OP-177 upgrades.

詢價 聯絡我們
OPA228P - 33MHz, 3nV/√Hz Precision Amplifier | TI
OPA228P

OPA228P - 33MHz, 3nV/√Hz Precision Amplifier | TI

Texas Instruments OPA228P is a high-precision, low-noise operational amplifier featuring 33 MHz gain-bandwidth performance and 3 nV/√Hz input-noise density, supplied in an 8-pin PDIP package for a temperature range of -55°C to 125°C. It is intended for applications that require both accurate DC measurements and wideband AC signal handling. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The precision amplifier category belongs to the broader operational-amplifier, analog-amplifier, and semiconductor hierarchies. The OPA228P occupies the low-noise, high-precision portion of that market because its published 3 nV/√Hz noise density supports accurate extraction of small signals, while its 33 MHz bandwidth allows the same device to process higher-frequency signals without requiring separate amplifier stages. The most important published characteristics are the 33 MHz gain-bandwidth product, 3 nV/√Hz input-noise density, single-amplifier configuration, and 8-pin PDIP package. The -55°C to 125°C operating range supports applications across extended industrial environments. Because it is packaged in a through-hole PDIP rather than a compact surface-mount package, the device is especially practical for laboratory instrumentation, precision measurement equipment, audio and analog test systems, and prototypes where socketed construction or hand assembly remains valuable. OPA228 and OPA227 devices are identified by Texas Instruments as pin-for-pin replacements for the industry-standard OP27 and OP37 families. This relationship supports legacy-design migration because engineers can focus on verifying offset, bias-current, supply, and stability requirements rather than redesigning the footprint. OPA228P specifically provides a single amplifier in the 8-pin PDIP configuration; dual and quad devices in the broader family serve different channel-count requirements. OPA228P is most appropriate for precision signal-conditioning paths, low-level sensor amplification, instrumentation amplifiers, audio measurement circuits, and laboratory measurement systems. Engineers should preserve the circuit topology and decoupling practices associated with the original OP27 or OP37 design while confirming that the operating points remain within the OPA228P specifications. For new layouts, verify input-offset requirements, bias-current behavior, output swing, supply range, noise contribution, and stability with external compensation or load capacitance. The 33 MHz bandwidth means that board layout, source impedance, grounding, and feedback-loop behavior remain important even when the target signal is predominantly low frequency. This page consolidates the verified manufacturer information, distributor pricing, same-package replacement options, and application-focused engineering guidance. It distinguishes documented OPA228P characteristics from unverified parameters and avoids presenting assumed electrical limits as manufacturer specifications.

詢價 聯絡我們
OPA228PA - 33MHz Low-Noise Precision Op Amp | Texas Instruments
OPA228PA

OPA228PA - 33MHz Low-Noise Precision Op Amp | Texas Instruments

The Texas Instruments OPA228PA is a high-precision, low-noise operational amplifier with a 33 MHz gain-bandwidth product, 3 nV/√Hz input-noise density, and an 8-pin DIP package. The OPA228 family combines precision DC performance with wide bandwidth for applications requiring accurate signal amplification across both low-frequency and AC signal paths. Its minimum recommended closed-loop gain is 5, making it particularly appropriate for instrumentation, filter, and signal-conditioning circuits that do not require unity-gain stability. An operational amplifier, commonly called an op amp, is a high-gain differential amplifier whose closed-loop behavior is controlled by an external feedback network. The OPA228 belongs to the precision operational-amplifier class within the broader voltage-feedback amplifier hierarchy. This category supports measurement, control, analog-signal conversion, filtering, buffering, and reference-current drive where low noise, low offset, and stable gain are more important than rail-to-rail operation. The headline specifications of the OPA228PA establish its position as a wide-band precision amplifier. Its 33 MHz gain-bandwidth product supports accurate amplification of signals well above audio frequency, while the 3 nV/√Hz input-noise density is valuable when the objective is to preserve small signals rather than merely process large ones. Because the OPA228 is optimized for closed-loop gains of 5 or greater, feedback ratios must be selected with that stability requirement in mind. The 8-pin DIP package also supports conventional through-hole PCB construction and prototype instrumentation. Technically, the OPA228 is designed for demanding precision analog front ends where both AC and DC performance contribute to the final measurement accuracy. High open-loop gain reduces the fraction of the input represented as error, while low input noise improves the signal-to-noise ratio for small source voltages. Its wide bandwidth can also make high-frequency phase margin a decisive layout consideration. The feedback resistor values, compensation network, source impedance, capacitive loading, and grounding arrangement should therefore be treated as part of the amplifier design rather than added afterward. Typical uses include precision instrumentation amplifiers, low-level sensor signal conditioning, active analog filters, audio and communications interfaces, laboratory measurement equipment, and feedback-control loops. The part is especially useful when a designer needs wide bandwidth and low noise together but does not require a unity-gain-stable amplifier. In filter and gain blocks, its gain setting must remain within the stable operating region specified by the manufacturer. The primary design consideration is stability. Use a closed-loop gain of at least 5 unless the application and compensation method are specifically supported by the manufacturer. Place input, feedback, and decoupling connections for short, low-inductance paths, and evaluate capacitive loading at the output. The DIP footprint also makes it practical to prototype a circuit before converting it to a smaller surface-mount package. This product page combines manufacturer specifications, sourcing information, application guidance, comparison fields, and practical design notes into one engineering-focused reference for evaluating the OPA228PA in precision analog designs.

詢價 聯絡我們
OPA228U - Precision Low-Noise Op Amp | Texas Instruments
OPA228U

OPA228U - Precision Low-Noise Op Amp | Texas Instruments

The Texas Instruments OPA228U is a high-precision operational amplifier with 3 nV/√Hz noise, 138 dB common-mode rejection, and operation from ±18 V to ±36 V, housed in an 8-pin SOIC package. It is optimized for closed-loop gains of 5 or greater and combines precision DC performance with wide bandwidth for instrumentation, analog signal conditioning, measurement, and low-noise audio applications. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while using negative feedback to set the closed-loop gain. The OPA228 belongs to the precision amplifier hierarchy, combining low-noise voltage amplification with accurate DC behavior. Its high precision makes it useful when small sensor signals must be amplified without adding substantial offset, drift, or common-mode error. The main features of the OPA228U include 3 nV/√Hz noise density, a 10 V/µs slew rate, and settling time listed in the manufacturer’s data. The device is intended for high-gain closed-loop configurations, where its precision and bandwidth provide useful signal fidelity. The verified distributor data identifies the part as a single amplifier in an 8-SOIC package and lists ±18 V to ±36 V operating capability. OPA228 devices are designed for applications requiring both AC and precision DC performance. The family combines low noise with high open-loop gain and strong common-mode rejection, helping preserve weak signals in systems where environmental offsets and interference matter. Because this is an analog precision component, supply layout, grounding, input bias-current compensation, and stable feedback components remain important in a complete design. Typical uses include sensor-signal conditioning, precision current and voltage measurement, laboratory instrumentation, audio preamplification, and low-level analog front ends. The OPA228U can be useful where a gain of approximately 5 or higher is appropriate, while applications requiring unity-gain stability should review the family details and choose the OPAx227 rather than assume interchangeability. Designers should check the complete manufacturer data sheet for input common-mode limits, output swing, bias current, offset voltage, supply-current behavior, and compensation requirements before finalizing a circuit. In particular, the 8-pin SOIC footprint requires careful attention to pin orientation and feedback routing. This page combines verified manufacturer and distributor information, package data, source links, and engineering-focused selection guidance to make OPA228U evaluation more actionable than a basic distributor listing alone.

詢價 聯絡我們
OPA2335AIDR - Dual Zero-Drift 5uV 2MHz Op Amp | TI
OPA2335AIDR

OPA2335AIDR - Dual Zero-Drift 5uV 2MHz Op Amp | TI

The Texas Instruments OPA2335AIDR is a dual-channel, zero-drift CMOS operational amplifier (op-amp) in an 8-pin SOIC package, delivering 5 uV (max) offset voltage and 0.05 uV/°C (max) drift over temperature. It provides a 2 MHz gain-bandwidth product, rail-to-rail output swing, and operates from a single 2.7V to 5.5V supply with a typical quiescent current of 285 uA per channel. The "D" suffix indicates tape-and-reel packaging and the "R" suffix designates the SOIC-8 (D) small-outline package. A zero-drift amplifier (also called auto-zero or chopper-stabilized op-amp) is a precision amplifier topology that continuously samples and corrects its own input offset voltage, virtually eliminating the 1/f noise corner and drift over time and temperature. Within the broader taxonomy, zero-drift op-amps sit beneath precision amplifiers and instrumentation amplifiers, above general-purpose CMOS op-amps; they are critical in any signal chain where DC accuracy over temperature matters more than absolute bandwidth. Key features include 5 uV maximum offset voltage, 0.05 uV/°C maximum drift, single-supply operation from 2.7V to 5.5V, 2 MHz GBW, rail-to-rail output, 285 uA quiescent current per channel, and a miniature SOIC-8 footprint. The chopper-stabilized topology eliminates the 1/f noise corner, producing flat noise spectral density down to DC - a feature classical CMOS op-amps cannot match. The OPA2335 uses TI's auto-zeroing architecture that combines a main amplifier with a nulling amplifier. The nulling amplifier periodically samples the offset and applies a correction, yielding near-zero long-term drift. This makes the device particularly well suited for high-gain DC stages, sensor signal conditioning, and 16-bit-plus precision analog-to-digital converter (ADC) front ends where offset drift directly translates to system error. Typical applications include transducer signal conditioning, electronic weighing scales (electronic balances), medical instrumentation such as ECG and patient monitors, temperature measurement (RTD and thermocouple amplifiers), and precision analog front-ends for industrial process control. In each case the OPA2335's near-zero drift preserves calibration accuracy over the full operating temperature range. When designing with the OPA2335, observe the standard zero-drift caveat: the auto-zero clock produces small intermodulation artifacts in the kHz region that can alias into audio-frequency bands - a small post-filter or careful GBW selection mitigates this. Decouple each supply pin with a 0.1 uF ceramic capacitor placed within a few millimeters of the IC. This page synthesizes distributor pricing, drop-in compatible alternatives in the SOIC-8 footprint, parametric comparisons with same-package peers, and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
OPA2336P - Dual MicroPower Rail-to-Rail Op Amp | Texas Instruments
OPA2336P

OPA2336P - Dual MicroPower Rail-to-Rail Op Amp | Texas Instruments

The Texas Instruments OPA2336P is a dual-channel, single-supply microPower CMOS operational amplifier with rail-to-rail output, a 20 µA typical quiescent current per amplifier, a maximum input offset voltage of 125 µV, a 1 pA input bias current, and a 115 dB open-loop gain. The device is offered in an 8-pin through-hole DIP package, making it suitable for prototypes, educational designs, and systems assembled with conventional radial or socketed DIP components. An operational amplifier is a voltage-gain element used to amplify the difference between two input voltages. The OPA2336 belongs to the microPower CMOS operational-amplifier family within the broader amplifier IC and signal-conditioning hierarchy. Its low quiescent current is especially relevant to battery-powered instrumentation because the amplifier continues to consume power even when its signal input is near zero. The rail-to-rail output allows the output voltage to approach the positive and negative supply limits under suitable load conditions, providing more usable output range from a limited supply voltage. The OPA2336 family combines low power consumption with precision-oriented performance. A maximum offset voltage of 125 µV supports accurate amplification of small signals, while the 1 pA input bias current is useful with high-impedance sensors and bias networks. The 115 dB open-loop gain indicates strong amplification capability, and the dual configuration provides two independent amplifier channels in one package. Identical electrical specifications are identified for the single, dual, and quad family members, allowing the same general signal-chain approach to be used when the required channel count changes. According to the manufacturer product information, the OPA2336 operates from 2.3 V to 5.5 V. The low-voltage operating range makes the amplifier appropriate for portable measurement systems, low-voltage sensor interfaces, battery-operated test equipment, and embedded instrumentation. The datasheet excerpt also describes operation with a negative supply, extending the common-mode capability below ground. This feature can simplify circuits that measure bipolar or unipolar sensor signals without adding a separate midrail reference. Typical uses include low-level sensor conditioning, current-to-voltage conversion, audio and communication interface stages, general-purpose voltage amplification, and precision analog measurement. The 100 kHz gain-bandwidth product and 0.03 V/µs slew rate shown in the component listing suit low-frequency and modest-bandwidth signal paths rather than high-speed video, RF, or precision audio applications. The 8-pin DIP package is mechanically convenient for laboratory assembly, but modern production designs may favor a surface-mount equivalent when board area, assembly automation, or vibration resistance is important. Designers should verify the exact pinout, common-mode range, output-load limitations, input protection behavior, and stability requirements in the manufacturer datasheet before finalizing a PCB. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must be biased so that the output remains in its linear operating region. Because the two channels share one package, independent noise and thermal conditions can affect them differently, particularly when one channel drives a low-impedance load while the other handles a high-impedance source. This page combines the confirmed manufacturer specifications with package information, practical analog-design guidance, sourcing fields, and a technical comparison framework. It also identifies where circuit-specific data must be taken directly from the manufacturer datasheet, helping engineers evaluate the OPA2336P without confusing family-level features with package-specific limitations.

詢價 聯絡我們
OPA234E - 36V Precision Operational Amplifier | Texas Instruments
OPA234E

OPA234E - 36V Precision Operational Amplifier | Texas Instruments

The Texas Instruments OPA234E is a low-power, precision operational amplifier in an 8-VSSOP package, specified for single-supply operation up to +36V and dual-supply operation up to ±18V. The device provides two amplifier channels, 250 uA per amplifier quiescent current, 25 nA maximum input bias current, 100 uV maximum offset voltage, and operation characterized at +2.7V, +5V, and ±15V. Its 8-VSSOP package supports compact analog signal-chain designs. An operational amplifier is a voltage-feedback analog IC used to amplify the difference between two input voltages while providing high input impedance and low output impedance. The OPA234E belongs to the precision operational-amplifier hierarchy, combining low offset, low bias current, and low quiescent current for instrumentation, sensor, and signal-conditioning applications. Its dual-channel architecture reduces package count when a design needs two matched amplifier functions. Key features include a wide supply range, low power consumption, low input bias current, and low offset voltage. The 250 uA-per-amplifier quiescent current is suitable for battery-powered and low-power systems, while the maximum 25 nA input bias current helps preserve sensor accuracy. The device is intended for precision signal conditioning where low bias and offset matter more than very high bandwidth. The verified product data identifies OPA234E as a single circuit in an 8-VSSOP package from the distributor listing, while the related OPA234 family data describes it as a dual operational-amplifier family member. The available source does not provide a verified gain-bandwidth figure, slew rate, noise density, common-mode range, output swing, or complete pinout, so those values must be confirmed from the manufacturer datasheet before design release. Typical applications include low-power sensor interfaces, precision current measurements, instrumentation signal conditioning, battery-powered equipment, and industrial control systems. The low quiescent current helps limit supply demand, but input bias current and offset errors still require careful source-impedance and calibration analysis. For PCB implementation, keep input traces short, provide stable bypassing at the supply pins, and avoid routing sensitive high-impedance inputs beside switching nodes. Verify the exact VSSOP pin mapping, supply limits, input common-mode range, and output swing against the authoritative OPA234 datasheet. This page combines verified distributor descriptions, available family specifications, and engineering guidance while clearly identifying missing parameters. This product data is synthesized from the supplied manufacturer-family and distributor sources rather than a complete manufacturer datasheet specification set.

詢價 聯絡我們