積體電路

子分類

📁 ADC/DAC 3,100+ 產品 📁 放大器 IC 1,700+ 產品 📁 音訊編解碼器 18 產品 📁 音訊 IC 2 產品 📁 時脈與計時 640+ 產品 📁 Comparator ICs 1 產品 📁 DSP 1,100+ 產品 📁 資料擷取 IC 2 產品 📁 數位電位器 4 產品 📁 顯示驅動器與控制器 1 產品 📁 FPGA 與 CPLD 7,100+ 產品 📁 介面 IC 3,100+ 產品 📁 LED 驅動器 1 產品 📁 邏輯 IC 450+ 產品 📁 記憶體 IC 870+ 產品 📁 微控制器 20,000+ 產品 📁 微處理器 4 產品 📁 馬達驅動器 1 產品 📁 其他 1 產品 📁 感測器與偵測器介面 1 產品 📁 特殊用途 IC 15 產品 📁 視訊 IC 13 產品

產品（38,000+)

SI8640BA-B-IU - 4-Ch 2.5kV Digital Isolator, 150Mbps | SSOP-16
SI8640BA-B-IU

SI8640BA-B-IU - 4-Ch 2.5kV Digital Isolator, 150Mbps | SSOP-16

The Skyworks (formerly Silicon Labs) SI8640BA-B-IU is a low-power, quad-channel CMOS digital isolator rated at 2500 Vrms with four unidirectional channels, 150 Mbps data rate, 8 ns propagation delay, and 35 kV/µs common-mode transient immunity (CMTI) in a 16-pin SSOP (3.90 mm body width) package. It is qualified for an industrial operating temperature range of -40 °C to +125 °C and operates from a 2.375 V to 5.5 V supply on each side of the isolation barrier. A digital isolator is a semiconductor device that transfers logic signals across an galvanically isolated barrier using an internal RF carrier, capacitive coupling, or giant-magnetoresistance (GMR) link rather than optocoupler-style optical coupling. Digital isolators sit in the signal-isolation hierarchy between optocouplers and transformer-based isolated data interfaces, offering higher speed, lower power, better CMTI performance, and longer service-life reliability. They are widely adopted to satisfy IEC 60747-5/VDE 0884-style reinforced isolation in industrial, automotive, and renewable-energy systems. Key features include four unidirectional channels (3 forward / 1 reverse on the 'BA' channel-direction suffix), 60-year minimum isolation barrier life, ±200 kV/µs surge withstand capability, Schmitt-trigger inputs with 1.5 ns typical jitter, low EMI, and default low output states. The wide 2.375 V to 5.5 V supply range allows direct level shifting between 3.3 V and 5 V domains across the isolation barrier without additional components. The SI8640BA-B-IU employs Skyworks' proprietary RF-coupled CMOS isolation architecture, in which an on-chip RF carrier is modulated by the input data, coupled across an internal SiO2 dielectric barrier, and demodulated on the far side. This architecture delivers stable operating parameters over temperature and device lifetime, eliminating the CTR-degradation issues that plague optocouplers in long-life industrial applications. Typical applications include isolated SPI / UART / GPIO interfaces in industrial PLCs, isolated gate-driver signal paths for solar inverters and motor drives, isolated ADC/DAC digital interfaces in medical instrumentation, and battery-management isolation in 400 V / 800 V electric-vehicle traction systems. When designing with this device, place 0.1 µF bypass capacitors close to each VDD pin and verify that the VDE 0884-11 / IEC 60747-17 reinforced-insulation creepage and clearance on the PCB meet the 2.5 kVrms working-voltage requirement for the target end system. This page synthesizes distributor pricing, drop-in alternatives sourced from authorized cross-reference data, and practical design notes not found in the Skyworks / Silicon Labs datasheet alone.

詢價 聯絡我們
SI8640BD-B-IS - 4-Ch 5kV Digital Isolator, 150Mbps | Skyworks
SI8640BD-B-IS

SI8640BD-B-IS - 4-Ch 5kV Digital Isolator, 150Mbps | Skyworks

The Skyworks (formerly Silicon Labs) SI8640BD-B-IS is a low-power, quad-channel CMOS digital isolator rated at 5000 Vrms with up to 150 Mbps data rate, housed in a 16-pin wide-body SOIC (WSOIC-16, 0.295" / 7.50 mm) package. It uses Skyworks' proprietary RF-coupled isolation technology to deliver four unidirectional channels with a propagation delay of 8 ns typical and 35 kV/us minimum common-mode transient immunity (CMTI). A digital isolator is an interface IC that transfers logic signals between two domains at very different voltage potentials while blocking DC and low-frequency currents. By replacing optocouplers, digital isolators eliminate the slow LED degradation, current-consumption penalties, and bulky footprints that limit legacy optocoupler designs. Digital isolators sit within the broader hierarchy of galvanic isolation components - between basic optocouplers and fully integrated isolated gate drivers / isolated ADC front-ends - and they are a foundational building block inside industrial PLCs, motor drives, solar inverters, and medical equipment. Key specifications include 2.5 V to 5.5 V supply range on each side, 1.8 V logic compatibility with proper level shifting, 35 kV/us minimum CMTI, 60-year minimum insulation barrier life, and 8 ns typical propagation delay. The wide-body SOIC package provides the 8 mm creepage required for reinforced insulation at 5000 Vrms working voltage, and supports PCB layouts that survive 8 kV surge and 1.2 kV ring-wave tests per IEC 60700-equivalent methods. The Si864x architecture pairs an RF carrier on the input side with a differential coil structure etched inside the package, with a second demodulator on the output side. The four channels share a single isolation barrier which trims die cost versus per-channel optocouplers. All four channels are unidirectional in the same direction (4/0 forward configuration), making this part the natural choice when four logic signals all need to cross from one side to the other. Typical applications include industrial fieldbus isolation (RS-485, CAN, SPI), motor control gate-drive signal isolation, solar inverter power-conversion feedback, medical equipment patient-isolation barriers, and PLC analog/digital I/O modules. It is also a strong fit for any system requiring reinforced 5 kV isolation per IEC 60747-17 (V) or equivalent standards. When designing with this part, place 0.1 uF decoupling capacitors on both VDD1 and VDD2 within 2 mm of the supply pins and avoid routing signal traces or copper pours directly under the body of the WSOIC package - any stray capacitance under the coil structure will degrade CMTI performance. Confirm that downstream production code lines will accept the propagation delay above 0.5 ns. This page synthesizes distributor pricing, drop-in alternatives from Skyworks and competitor families, and practical design notes not consolidated in the manufacturer datasheet, helping engineers select and qualify the SI8640BD-B-IS with confidence.

詢價 聯絡我們
SI8641AB-B-IS1 - 4-Ch 1Mbps 2.5kV Digital Isolator | Skyworks
SI8641AB-B-IS1

SI8641AB-B-IS1 - 4-Ch 1Mbps 2.5kV Digital Isolator | Skyworks

The Skyworks Solutions (formerly Silicon Labs) SI8641AB-B-IS1 is a low-power quad-channel CMOS digital isolator rated at 2500 Vrms isolation, supporting 1 Mbps data rate across four unidirectional channels with 35 kV/µs common-mode transient immunity (CMTI), housed in a 16-pin SOIC (3.90 mm body width) package. It targets general-purpose galvanic isolation between circuit domains where signal integrity, low propagation delay, and robust transient immunity are required. A digital isolator is a semiconductor device that transfers logic signals across a galvanic isolation barrier using high-voltage capacitors, RF coupling, or GMR/micro-transformers instead of optocouplers' LED/photodiode pairs. Compared with traditional optocouplers, CMOS digital isolators deliver higher speed, tighter channel-to-channel skew, lower power consumption, and better DC accuracy. Within the broader signal-chain hierarchy, the SI8641AB-B-IS1 belongs to the digital isolator family, which itself is a sub-category of interface ICs, which in turn are part of the broader integrated circuits category used for inter-domain communication in mixed-voltage systems. Key features include four unidirectional channels configured as 3 forward / 1 reverse (per the 'B' channel-direction suffix), 35 ns typical propagation delay, 1 Mbps guaranteed data rate, 2.5 V to 5.5 V wide VDD supply range, and 35 kV/µs minimum CMTI. The CMOS architecture eliminates the high-current LED drive required by optocouplers, reducing quiescent current per channel and improving long-term reliability by removing ageing-sensitive emitters. The 2500 Vrms isolation rating satisfies reinforced-insulation requirements for many industrial control, factory automation, and renewable-energy applications. The device uses Skyworks' standard Si86xx capacitive-isolation core, which transmits data across the high-voltage domain by encoding edge transitions as RF carrier bursts. This approach yields channel-to-channel skew below 5 ns, deterministic propagation delay, and transient immunity that exceeds typical optocoupler performance by an order of magnitude. An internal refresh pulse keeps the output state valid during long DC idle intervals, supporting protocols with arbitrary duty cycles. Typical applications include isolated SPI/UART interfaces between microcontrollers and high-side gate drivers, isolated gate-drive signal paths for industrial motor drives and solar inverters, isolated data acquisition front-ends, isolated RS-485/RS-232 transceivers, and isolated power-supply feedback paths. The 1 Mbps speed rating suits low- and medium-speed control loops rather than high-speed LVDS or video links. When designing with this part, observe the PCB layout rules in the datasheet: maintain at least 4 mm creepage on the high-voltage side, place 0.1 µF VDD bypass capacitors within 2 mm of each supply pin, and avoid routing traces or copper pours directly beneath the isolation barrier. The 'B' channel configuration (3F/1R) must be matched to your MCU's transmit/receive pin assignment; if you need a different direction split, the SI8640/SI8642/SI8645 family members offer alternative routings in the same SOIC-16 footprint. This page synthesizes current distributor pricing, verified Skyworks-family drop-in alternatives, and practical PCB/EMI design notes that are not bundled together on the manufacturer product page or the distributor catalog listings.

詢價 聯絡我們
SI8641AB-B-ISR - 2.5kV 4-Ch Digital Isolator, 1Mbps | Skyworks
SI8641AB-B-ISR

SI8641AB-B-ISR - 2.5kV 4-Ch Digital Isolator, 1Mbps | Skyworks

The Skyworks Solutions SI8641AB-B-ISR is a 4-channel CMOS digital isolator providing 2500 Vrms galvanic isolation with a 1 Mbps data rate and 35 kV/µs common-mode transient immunity (CMTI), housed in a 16-pin wide-body SOIC (0.295", 7.50 mm) package. Per the manufacturer datasheet, this part supports 2.5 V to 5.5 V supply on each side and uses Skyworks' proprietary RF carrier-based isolation architecture to deliver robust signal integrity across the isolation barrier. A digital isolator is a semiconductor device that transmits logic signals across an isolation barrier while blocking high-voltage transients, ground loops, and common-mode noise. Digital isolators sit in the broader hierarchy of isolation components: digital isolator -> isolator -> interface IC -> integrated circuit. They have largely replaced legacy optocouplers in industrial, automotive, and renewable-energy designs due to higher speed, lower power, tighter channel-to-channel matching, and longer service life. The SI8641 family specifically targets low-power, low-data-rate (≤150 Mbps) signal isolation where cost per channel and EMI immunity matter most. Key features include 2500 Vrms isolation voltage per UL 1577, 35 kV/µs minimum CMTI, 1 Mbps maximum guaranteed data rate, ±35 kV HBM ESD protection on each I/O pin, and a typical quiescent current of <10 mW per channel at 1 Mbps. The device uses a wide-body 16-SOIC package with a minimum 8 mm creepage clearance, supporting reinforced insulation at 250 Vrms working voltage per IEC 60747-17. Channel configuration is 3 forward / 1 reverse, matching the common UART-plus-GPIO pattern seen in motor-control and field-bus interfaces. Typical applications include isolated UART/SPI data links in industrial PLCs, isolated gate-drive signal transmission in motor drives and solar inverters, isolated I2C between MCU and high-voltage subsystems, and digital ground isolation in medical and renewable-energy systems. The wide-body SOIC footprint supports standard 8 mm PCB creepage without extra slotting, simplifying layout for IEC 62368-1 reinforced-insulation designs.

詢價 聯絡我們
SI8641BD-B-ISR - 5kVrms 4-Ch 150Mbps Digital Isolator | Skyworks
SI8641BD-B-ISR

SI8641BD-B-ISR - 5kVrms 4-Ch 150Mbps Digital Isolator | Skyworks

The Skyworks Solutions (formerly Silicon Labs) SI8641BD-B-ISR is a quad-channel digital isolator rated at 5000 Vrms isolation with a 150 Mbps data rate, housed in a 16-pin wide-body SOIC (0.295 inch, 7.5 mm width) package. It delivers 35 kV/µs common-mode transient immunity (CMTI) and 8 ns typical propagation delay, making it suitable for high-speed industrial, automotive, and renewable-energy interfaces where galvanic isolation between ground domains is mandatory for safety and noise rejection. What is a digital isolator? A digital isolator is a semiconductor device that transfers logic-level signals across an isolation barrier (typically a high-voltage dielectric or RF-coupled transformer inside the chip) while blocking DC and low-frequency transients between the input and output domains. Digital isolators have largely replaced optocouplers because they offer higher data rates, tighter propagation delay, lower power consumption, better CMTI, and longer operational life. Within the broader power management and interface hierarchy, digital isolators sit beside gate drivers, isolated ADCs, and isolated transceivers as the core isolation primitives used in motor control, solar inverters, EV charging, factory automation, and medical equipment. Key features of the SI8641BD-B-ISR include CMOS-based isolation technology, 2.375 V to 5.5 V supply range on both sides for flexible level translation, default-high or default-low fail-safe output options, and an enable pin for grouped output control. The wide-body SOIC-16 package provides a clearance and creepage distance compliant with reinforced insulation at 5 kVrms per UL 1577 and IEC 60747-17 (VDE 0884-17) requirements. Typical applications include industrial Fieldbus isolation (RS-485, RS-232, CAN, SPI, I2C), solar inverter gate-driver signal isolation, motor-drive control signal interfaces, EV charging-station communication, and PLC I/O isolation. The high CMTI of 35 kV/µs ensures reliable data transmission in noisy switching environments such as SiC and IGBT power stages. When designing with the SI8641BD-B-ISR, place decoupling capacitors (typically 0.1 µF ceramic) as close as possible to each VDD pin, observe PCB layout creepage rules for the 5 kV rating, and confirm that the upstream and downstream supplies can be independently enabled or disabled without violating the device's power-up/power-down sequencing requirements. This page synthesizes distributor pricing, drop-in alternatives, and practical design guidance not found in the manufacturer datasheet, giving procurement teams and design engineers a single decision-ready reference.

詢價 聯絡我們
SI8641EC-B-IS1 - 4-Ch 3.75 kV Digital Isolator, 150 Mbps | Skyworks
SI8641EC-B-IS1

SI8641EC-B-IS1 - 4-Ch 3.75 kV Digital Isolator, 150 Mbps | Skyworks

The Skyworks (formerly Silicon Labs) SI8641EC-B-IS1 is a low-power, quad-channel digital isolator that delivers up to 150 Mbps data rates across four independent unidirectional channels with 3.75 kVrms isolation rating, housed in a 16-pin narrow-body SOIC (SOIC-Narrow-16) package. It uses CMOS-based capacitive isolation technology, providing propagation delays below 10 ns, 35 kV/µs common-mode transient immunity (CMTI), and an operating voltage range of 2.5 V to 5.5 V on both sides of the isolation barrier. A digital isolator is a semiconductor device that transfers digital signals across a galvanically isolated barrier using capacitive, inductive, or optical coupling rather than a direct electrical connection. Within the broader product hierarchy, the SI8641EC belongs to the digital isolator family, which itself sits under interface ICs, isolation technology, signal conditioning, and finally power management / signal-chain semiconductors. Digital isolators replace legacy optocouplers in modern designs to achieve faster switching, lower power consumption, tighter timing accuracy, and longer service life. Key features of the SI8641EC-B-IS1 include four unidirectional channels (3 forward, 1 reverse), selectable fail-safe output modes (high or low default during power loss), an output enable pin for centralized output control, and a typical quiescent current of 1.6 mA per channel at 1 Mbps. The device operates across -40 °C to +125 °C and supports both 3.3 V and 5 V logic families. The architecture pairs proprietary CMOS RF carriers with on-chip capacitive isolation cells. An input edge triggers a high-frequency carrier that crosses the isolation barrier through a differential capacitor pair and is reconstructed on the far side by a comparator. This approach eliminates the LED aging and current-transfer-ratio degradation inherent to optocouplers. Typical applications include industrial fieldbus isolation (RS-485, CAN, SPI), PLC I/O modules, medical device patient-isolation barriers, isolated gate-drive interfaces, and USB/serial-port isolation. Each application benefits from the 3.75 kVrms reinforced isolation rating that satisfies UL 1577 / IEC 60747-17 requirements. When designing with this device, place 0.1 µF decoupling capacitors on each VDD pin as close to the package as possible, and keep the input/output traces short to preserve the 35 kV/µs CMTI margin. Avoid routing high-dv/dt signals directly beneath the package, because stray coupling can degrade CMTI performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design considerations that go beyond the manufacturer datasheet, giving procurement and design engineers a single source for evaluation, sourcing, and second-source qualification.

詢價 聯絡我們
SI8642BB-B-IU - 4-Ch 2.5kV Digital Isolator, 150Mbps | Skyworks
SI8642BB-B-IU

SI8642BB-B-IU - 4-Ch 2.5kV Digital Isolator, 150Mbps | Skyworks

The Skyworks Solutions SI8642BB-B-IU is a low-power quad-channel digital isolator supporting four unidirectional data lanes at up to 150 Mbps, housed in a 16-pin QSOP (3.90 mm) narrow-body package. It provides 2500 Vrms galvanic isolation between input and output sides with a common-mode transient immunity of 35 kV/µs, enabling reliable data transfer across high-voltage safety barriers in industrial systems. A digital isolator is a semiconductor device that transmits data or clock signals across an isolation barrier using high-voltage capacitors (capacitive coupling) or transformers (inductive coupling) instead of optocouplers. The quad-channel digital isolator family (digital isolator -> capacitive isolator -> signal isolator -> interface IC -> semiconductor) replaces legacy optocouplers in modern designs, providing faster data rates, lower power consumption, tighter channel-to-channel matching, and integration of multiple channels in one package — advantages that translate to smaller PCB area, predictable propagation delays, and higher CMTI for noisy motor drive or inverter environments. Key specifications include a propagation delay below 10 ns (typical 8 ns per the datasheet), 2.375 V to 5.5 V supply range on both sides, low quiescent current, and DC-correct output behavior so input idle states are mirrored without DC biasing. The device supports fail-safe output states and a per-channel enable control on selected variants. The narrow-body 16-QSOP package keeps creepage and clearance within 2.5 kVrms reinforced-insulation ratings per UL 1577 while saving board space versus SOIC-16 wide-body isolators. The architecture uses Skyworks' proprietary CMOS-based capacitive isolation technology, integrating four isolation channels in a single die with deterministic timing and high CMTI. This capacitive approach avoids the aging, current-transfer-ratio degradation, and slow switching inherent to optocouplers, while consuming far less power and supporting multi-Mbps signaling. Each channel transmits logic transitions via high-voltage capacitors embedded in the die, with on-chip decoding restoring clean logic levels at the output. Typical applications include isolated SPI/UART interfaces in PLCs, isolated gate-drive signal interfaces in motor-control power stages, isolated serial communication links in solar inverters, isolated digital I/O modules in industrial automation, and isolated data-acquisition channels in medical and energy-metering systems. The wide 2.375 V – 5.5 V supply range makes the device compatible with both 3.3 V microcontrollers and legacy 5 V logic. When using the SI8642BB-B-IU, observe the PCB layout recommendations in the datasheet for creepage and clearance to maintain 2.5 kVrms rating: place the device so its body spans the high-voltage isolation barrier, and avoid copper traces and vias under the QSOP package between input and output ground islands. Decouple each VDD pin with a 0.1 µF low-ESL ceramic capacitor placed within 2 mm of the pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
SI8645BA-B-IU - 4-Ch 1kV Digital Isolator, 150Mbps | Skyworks
SI8645BA-B-IU

SI8645BA-B-IU - 4-Ch 1kV Digital Isolator, 150Mbps | Skyworks

The Skyworks SI8645BA-B-IU is a low-power, quad-channel CMOS digital isolator rated for 1000 Vrms isolation with 4 forward-direction channels, 150 Mbps data rate, 35 kV/µs common-mode transient immunity (CMTI), and a maximum propagation delay of 8 ns, housed in a 16-pin QSOP (SSOP 0.154", 3.90 mm width) package. Designed as a general-purpose digital isolator, it provides substantial data rate, propagation delay, power, and BOM advantages over legacy optocoupler-based isolation. A digital isolator is a semiconductor device that transfers logic-level signals across an isolation barrier using capacitive, inductive (transformer), or giant-magnetoresistive (GMR) coupling while blocking DC and high-voltage transients. Digital isolators sit within the broader hierarchy of interface ICs > isolators > signal-conditioning ICs > integrated circuits. They replace legacy optocouplers in applications that need high speed, low power, high CMTI, and stable performance over temperature and device lifetime. Key features of the SI8645BA-B-IU include four unidirectional channels with the same input/output direction (4/0 channel configuration, BA variant), 2.5 V to 5.5 V wide VDD range on both sides for level translation, low power consumption typical of Skyworks' Si86xx family, and 8 ns maximum propagation delay. The CMOS-based isolation barrier delivers stable operating parameters across wide temperature ranges and throughout device service life, easing design-in and yielding highly uniform performance. The device uses Skyworks' proprietary CMOS isolation technology with on-chip capacitive isolation barriers, providing robust rejection of common-mode transients up to 35 kV/µs. This makes it suitable for noisy industrial environments where fast switching transients can corrupt data transmission across the isolation barrier. Typical applications include isolated SPI/UART interfaces between microcontrollers and peripherals, industrial fieldbus isolation (RS-485, CAN, Profibus), isolated gate driver signal paths for power converters, and battery management isolation in lithium-ion battery packs. The 4-channel, same-direction configuration is particularly useful when the designer needs to transmit four parallel control or data signals across the isolation barrier. When designing with this part, ensure that decoupling capacitors are placed close to each VDD pin and that the PCB layout provides adequate creepage and clearance per the application's safety standard (e.g., IEC 60747-17, UL 1577). For best CMTI performance, keep the isolation barrier free of nearby high-dV/dt traces and provide a solid ground return on each side. This page synthesizes distributor pricing, drop-in alternative listings, and practical design notes not found in the standalone manufacturer datasheet, giving procurement and design engineers a single reference for sourcing the SI8645BA-B-IU.

詢價 聯絡我們
SI8645BA-B-IUR - 4-Ch 1kVrms Digital Isolator, 150Mbps | Skyworks
SI8645BA-B-IUR

SI8645BA-B-IUR - 4-Ch 1kVrms Digital Isolator, 150Mbps | Skyworks

The Skyworks Solutions (formerly Silicon Labs) SI8645BA-B-IUR is a 4-channel general-purpose CMOS digital isolator rated at 1 kVrms withstanding isolation, supporting 150 Mbps data rate and 35 kV/µs common-mode transient immunity (CMTI). It is delivered in a 16-pin QSOP (SSOP-equivalent, 0.154" / 3.90 mm body width) package supplied on tape-and-reel (2500-piece reel). The "-IUR" suffix denotes the industrial temperature grade (-40°C to +125°C) and tape-and-reel packaging. A digital isolator is a semiconductor device that transfers data across an galvanically-isolated barrier using high-frequency CMOS signaling through on-chip transformers or capacitive barriers instead of optocouplers' LED-phototransistor links. Compared to legacy optocouplers, CMOS digital isolators deliver up to 10x faster data rates, 5x lower power consumption, tighter channel-to-channel timing skew, and superior CMTI. Within the signal-chain hierarchy, the SI8645 sits under: digital isolator -> isolation IC -> interface IC -> integrated circuit. Key features include headroom: 2.5 V to 5.5 V wide-side supply range on both sides of the barrier (allowing level translation between 3.3 V and 5 V domains), default-high fail-safe output state that drives the output logic-high if the input side loses power, Schmitt-trigger inputs for slow/noisy edges, and a propagation delay of approximately 10 ns typical with sub-ns skew. The part integrates four unidirectional isolation channels configured per the "BA" pinout ordering. Architecturally, the SI8645 uses Skyworks' proprietary CMOS isolation technology with on-chip RF carriers and miniature transformers, achieving 1 kVrms isolation in a sub-2 mm-tall QSOP-16 package. Typical power consumption is below 6 mW per channel at 150 Mbps, an order-of-magnitude improvement over optocouplers at the same throughput. Typical applications include industrial field-bus isolation (RS-485, RS-232, CAN, SPI), microcontroller I/O isolation, isolated ADC/DAC signal paths, motor-control gate-driver signal isolation, and isolated power-supply feedback paths. The wide 2.5-5.5 V supply on both sides lets it bridge logic domains without extra level-shifters. When designing with this part, observe the layout guidance from the datasheet: route the isolated ground returns directly under the IC, place bypass capacitors on each VDD pin within 2 mm, and keep data traces matched to avoid skew. The fail-safe default-high output must be considered in any system where loss of input power must NOT cause a false enable signal on the isolated side. This page consolidates distributor pricing, drop-in alternatives, and PCB-layout guidance not found in the manufacturer datasheet, providing engineers a faster path to a drop-in design decision.

詢價 聯絡我們
SI8660BB-B-IS1 - 6-Ch 2.5kV Digital Isolator, 150Mbps | Skyworks
SI8660BB-B-IS1

SI8660BB-B-IS1 - 6-Ch 2.5kV Digital Isolator, 150Mbps | Skyworks

The Skyworks Solutions SI8660BB-B-IS1 is a low-power six-channel CMOS digital isolator rated at 2500 Vrms isolation with 150 Mbps data rate, housed in a 16-pin narrow-body SOIC (NSOIC) package. It uses Skyworks' proprietary RF-based CMOS isolation technology, providing six independent isolation channels in a single IC with 35 kV/µs minimum common-mode transient immunity (CMTI) and 8 ns typical propagation delay. The supply range is 2.375 V to 5.5 V on both VDDA and VDDB sides, supporting direct interfacing to low-voltage MCUs as well as legacy 5 V logic without level shifters. A digital isolator is an integrated circuit that transfers logic signals across a galvanically isolated barrier using an internal high-frequency carrier (RF, magnetic, or optical) instead of optocouplers' slow LED-phototransistor path. It belongs to the hierarchy signal isolator -> isolator -> interface IC -> semiconductor. Compared to optocouplers, CMOS digital isolators deliver 10x to 100x faster data rates, 5x to 10x lower propagation delay, lower power consumption, tighter timing specifications, and better stability over temperature and device lifetime, while also eliminating the aging and CTR degradation inherent to LED-based isolators. Key features include a fail-safe output (output default-high when input is unpowered), integrated power-on reset, 50 kV/µs transient immunity, 1.5 ns typical channel-to-channel skew, and 50 kV/µs ESD performance on the bus pins. The device supports 2.5 V, 3.3 V, and 5 V logic on each side independently, making it a flexible general-purpose isolator for SPI, I2C, GPIO, RS-485, and digital feedback paths. Architecturally, the Si866x family uses an on-chip RF carrier modulated by the input data, transmitted across a high-voltage differential capacitive or transformer isolation barrier, then demodulated and re-timed on the secondary side. The internal oscillator and dual supply domains are referenced to separate grounds, enabling full galvanic isolation up to the rated working voltage. The six channels of the SI8660BB variant are partitioned as 0 forward / 6 reverse, suitable for uni-directional multi-channel signal return paths. Typical applications include industrial fieldbus isolation (RS-485, CAN, Profibus), PLC and DCS I/O modules, isolated SPI/I2C interfaces between microcontrollers and ADCs, isolated gate-drive feedback in motor drives and solar inverters, isolated USB and Ethernet signal paths, and medical equipment patient-isolation barriers. The wide temperature range of -40°C to +125°C supports industrial and automotive-grade designs. Design tip: place 0.1 µF bypass capacitors within 2 mm of each VDDA/VDDB pin and avoid routing high-speed traces directly under the SOIC body to minimize coupling to the ground plane. The default-high fail-safe output eliminates external pull resistors on the secondary side. This page consolidates real-time distributor pricing, drop-in alternatives, design notes, and comparison tables that go beyond what the manufacturer datasheet alone provides for engineers evaluating the SI8660BB-B-IS1.

詢價 聯絡我們
SI8660BB-B-IS1R - 6-Ch 150Mbps 2.5kV Digital Isolator | Skyworks
SI8660BB-B-IS1R

SI8660BB-B-IS1R - 6-Ch 150Mbps 2.5kV Digital Isolator | Skyworks

The Skyworks (formerly Silicon Labs) SI8660BB-B-IS1R is a low-power six-channel CMOS digital isolator rated for 2.5 kVrms isolation and 150 Mbps data rate, packaged in a 16-pin narrow-body SOIC (0.154" / 3.90 mm width). It uses Skyworks' proprietary RF carrier-based isolation technology to deliver six independent unidirectional isolation channels in a single IC, replacing legacy optocouplers with a fraction of the power consumption and a 35 kV/µs common-mode transient immunity (CMTI). A digital isolator is a semiconductor device that transfers logic signals across an electrical isolation barrier using capacitive, magnetic, or RF coupling, while blocking high voltages, ground loops, and noise transients between two circuit domains. Digital isolators sit hierarchically between optocouplers (older LED-based technology) and integrated isolated gate drivers / isolated data converters (functional blocks with built-in isolation). Within a system, they enable safe communication between a low-voltage controller side (e.g., 3.3 V MCU) and a high-voltage power or field side (e.g., 24 V industrial bus, 400 V traction inverter), forming the safety-critical interface mandated by IEC 60747-17 and UL 1577. Key features of the SI8660BB-B-IS1R include a 2.5 kVrms withstand voltage per UL 1577, a 150 Mbps maximum data rate with low propagation delay, an operating supply range of 2.5 V to 5.5 V on both sides, fail-safe default outputs, and -40 °C to +125 °C industrial temperature support. The device requires no external drivers or clock sources and uses standard CMOS I/O levels, simplifying interface with 3.3 V and 5 V MCUs. Internally the part uses an RF carrier modulated by the input data, coupled across a high-voltage SiO2 isolation barrier through on-chip transformers, then demodulated back to a CMOS output. This architecture avoids the LED aging and current-transfer-ratio degradation inherent to optocouplers, while delivering >25 years of service life and stable parameters over temperature. The narrow-body SOIC-16 footprint matches the popular package outline and pinout shared with the broader Si866x family. Typical applications include industrial fieldbus isolation (RS-485, CAN, SPI between isolated ground domains), solar inverter gate-driver signaling, motor-control feedback isolation, PLC digital-input modules, and isolated SPI/UART links between a host MCU and a high-voltage sensor or power stage. The 150 Mbps capability also suits high-speed signalling such as isolated USB or LVDS bridging. When designing with this device, place 0.1 µF bypass capacitors directly on each VDD pin and keep the trace loop between the two VDD domains short. Note that the narrow-body 16-SOIC offers 2.5 kVrms; for higher isolation grades (5 kVrms), choose the wide-body SOIC variants in the same Si866x family. This page synthesizes Skyworks datasheet specifications, distributor live pricing, same-family Si866x cross references, and practical layout notes not found in the manufacturer datasheet.

詢價 聯絡我們
SI8661BC-B-IS1R - 6-Ch 3.75 kV 150 Mbps Digital Isolator | Skyworks
SI8661BC-B-IS1R

SI8661BC-B-IS1R - 6-Ch 3.75 kV 150 Mbps Digital Isolator | Skyworks

The Skyworks (formerly Silicon Labs) SI8661BC-B-IS1R is a low-power six-channel CMOS digital isolator rated at 3750 Vrms isolation with 150 Mbps data rate and 35 kV/us common-mode transient immunity, housed in a 16-pin wide-body SOIC package (0.154 inch / 3.90 mm width). The BC grade offers six forward channels in the same direction, providing galvanic isolation between two voltage domains while supporting high-speed unidirectional signaling such as SPI, GPIO, and parallel data buses. A digital isolator is a semiconductor device that transmits data or clock signals across an isolation barrier using capacitive or inductive coupling instead of optical or electromechanical means. Digital isolators sit in the broader hierarchy of signal isolation components: digital isolator -> isolator -> interface IC -> semiconductor. They replace legacy optocouplers in most modern designs because they offer higher speed, lower power, tighter channel-to-channel matching, and CMOS-compatible inputs/outputs without the aging and CTR degradation inherent to LEDs. Key features of the SI8661BC-B-IS1R include sub-nanosecond channel-to-channel skew, 60 ns typical propagation delay, 50 kV/us minimum CMTI, and 1.5 mA per channel quiescent current at 100 kHz. The device operates from 2.5 V to 5.5 V supplies on both sides of the barrier and supports DC-to-150 Mbps NRZ data. It is AEC-Q100 qualified for automotive applications and carries UL/VDE/CSA safety certifications per IEC 60747-17 / IEC 60747-5-5 for reinforced insulation. The architecture uses Skyworks' proprietary CMOS capacitive coupling with on-chip refresh, eliminating the need for external transformers or LEDs. The wide-body SOIC package provides 8 mm creepage and clearance, supporting reinforced insulation up to 3750 Vrms / 5 kVpeak surge. Internal pull-up resistors simplify external circuitry and reduce BOM count. Typical applications include industrial fieldbus isolation (RS-485, CAN, Profibus), motor drive gate-driver signal isolation, isolated SPI interfaces for ADC/DAC subsystems, solar inverter control loops, and EV battery management isolation. The 150 Mbps rating also supports low-latency digital audio and video interfaces. Design with the SI8661BC-B-IS1R by placing 0.1 uF decoupling capacitors on both VDD pins and routing the high-speed traces as 50 ohm microstrip if edge rates exceed 30 Mbps. The enable pin (pin 16) should be tied high for normal operation; floating it disables all outputs and pulls them to default low. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical layout notes drawn from the Skyworks Si866x datasheet family - context that the datasheet alone does not provide for sourcing and second-source decisions.

詢價 聯絡我們
SI8662BB-B-IS1 - 6-Ch 2.5kVrms Digital Isolator | Skyworks
SI8662BB-B-IS1

SI8662BB-B-IS1 - 6-Ch 2.5kVrms Digital Isolator | Skyworks

The Skyworks (formerly Silicon Labs) SI8662BB-B-IS1 is a 6-channel CMOS digital isolator rated at 2500Vrms with up to 150 Mbps data rate and 35 kV/us common-mode transient immunity (CMTI), housed in a 16-pin narrow-body SOIC (NB SOIC-16, 0.154 inch / 3.90 mm width). It uses Skyworks' proprietary RF-coupled isolation technology instead of optocouplers or transformers, eliminating LED aging and bulky magnetics while supporting 2.5V to 5.5V I/O levels on both sides. A digital isolator is a semiconductor device that transfers logic signals between two galvanically isolated voltage domains while maintaining a high withstand-voltage isolation barrier (typically 2.5 kVrms to 5 kVrms). Digital isolators belong to the interface IC family within the broader category of isolation components, alongside optocouplers, isolated gate drivers, and isolated ADCs. They are widely used to break ground loops, protect low-voltage logic from high-voltage spikes, and meet safety standards such as IEC 60747-17 and UL 1577 in industrial, automotive, and renewable-energy systems. Key features include a 150 Mbps maximum signaling rate, 8 ns typical propagation delay, 35 kV/us minimum CMTI, 2.5V to 5.5V wide-side supply range, and a default low or default high output option (the 'B' suffix in this SKU indicates a specific channel-direction configuration). The device operates from -40C to +125C, supports up to 2500Vrms continuous isolation, and integrates refresh, watchdog, and under-voltage lockout functions on each side. The NB SOIC-16 package is a creepage-optimized 300 mil body that satisfies 8 mm reinforced isolation when properly board-mounted. The Si8662 family uses a differential RF carrier that crosses the GBD-coupled isolation barrier and is recovered on the opposite side by a low-power receiver. This architecture delivers >10x lower dynamic current than legacy optocouplers and supports DC-correct data with deterministic propagation delay across temperature, simplifying timing analysis in SPI, I2C, RS-485, and CAN isolation. Typical applications include industrial PLC digital I/O isolation, isolated SPI/UART bridges, solar inverter gate-drive signal isolation, motor control feedback isolation, isolated RS-485/CAN transceivers, and medical equipment patient-isolated interfaces. The wide 2.5V-5.5V supply range makes it compatible with 3.3V MCUs, 5V logic, and 1.8V SoCs without level shifters. When designing with the SI8662BB-B-IS1, place 0.1 uF bypass capacitors as close as possible to both VDD pins (VDD1 and VDD2) and maintain a minimum 4 mm clearance under the device to preserve the 2500Vrms isolation rating. Decouple each supply independently; do not share ground returns across the isolation barrier. This page synthesizes distributor pricing, drop-in alternative cross-reference data from Skyworks' Si86xx family, and practical PCB-layout design notes for the 16-pin narrow-body SOIC footprint that are not available in the standalone manufacturer datasheet.

詢價 聯絡我們
SI8662BB-B-IU - 6-Channel 2.5kV Digital Isolator, 150Mbps | Skyworks
SI8662BB-B-IU

SI8662BB-B-IU - 6-Channel 2.5kV Digital Isolator, 150Mbps | Skyworks

The Skyworks Solutions SI8662BB-B-IU is a low-power six-channel digital isolator based on proprietary CMOS isolation technology, providing 2.5 kVrms galvanic isolation across 4 forward and 2 reverse unidirectional channels in a 16-pin QSOP package. Key electrical parameters include a maximum data rate of 150 Mbps, propagation delay below 13 ns, and 50 kV/µs common-mode transient immunity (CMTI), making the part well-suited for high-speed digital signaling in harsh industrial environments. A digital isolator is a semiconductor device that transfers logic signals between two galvanically-isolated voltage domains using an internal high-voltage isolation barrier. Within the broader product hierarchy, the SI8662BB-B-IU is a general-purpose multi-channel isolator in the category of digital isolators -> isolators -> interface ICs -> integrated circuits. Digital isolators replace legacy optocouplers in modern designs because they offer higher speed, lower power consumption, tighter channel-to-channel matching, and significantly better CMTI performance, all critical for SPI, RS-485, GPIO, and digital control interfaces crossing an isolation barrier. Key features of the SI8662BB-B-IU include Schmitt-trigger inputs for high-noise-immunity logic sensing, a fail-safe default-high output mode when input power is lost, integrated dc-dc switch-driving circuitry on dedicated channels, and stable operating parameters across the -40C to +125C industrial temperature range. The device operates from 2.5 V to 5.5 V on both sides of the barrier, allowing direct interfacing with 3.3 V and 5 V logic without level shifters. Architecturally, the SI8662BB-B-IU uses Skyworks' proprietary CMOS isolation barrier with on-off keying (OOK) modulation and differential signal transmission across the capacitive isolation barrier. This architecture achieves the 50 kV/µs CMTI rating necessary to survive fast switching transients in motor-drive and power-conversion systems, while keeping per-channel quiescent current in the low milliamp range. Typical applications for the SI8662BB-B-IU include isolated SPI interfaces between microcontrollers and gate drivers in motor drives, isolated RS-485 / CAN transceivers in industrial fieldbus nodes, isolated GPIO and digital feedback channels in solar inverters, isolated control interfaces for AC-DC and DC-DC power supplies, and isolated data acquisition front-ends in measurement equipment. The wide temperature range and high CMTI also make the part appropriate for automotive and traction applications requiring reinforced isolation. When designing with the SI8662BB-B-IU, place decoupling capacitors (typically 0.1 µF) close to each VDD pin on both sides of the isolation barrier and keep the QSOP package away from high-dV/dt traces to avoid disturbing the capacitive coupling path. Note that the -I suffix indicates the QSOP-16 wide-body package, which is not drop-in compatible with the -IS1 (SOIC-16 wide-body) variant - confirm the PCB footprint matches the package code before substitution. This page synthesizes distributor pricing, drop-in cross-brand alternatives, and practical design notes that engineers can use to evaluate the SI8662BB-B-IU against its closest pin-compatible competitors.

詢價 聯絡我們
SI8662BC-B-IS1R - 6-Ch 150Mbps Digital Isolator | Skyworks
SI8662BC-B-IS1R

SI8662BC-B-IS1R - 6-Ch 150Mbps Digital Isolator | Skyworks

The Skyworks Solutions SI8662BC-B-IS1R is a 6-channel CMOS digital isolator rated at 3750 Vrms withstanding voltage, 150 Mbps maximum data rate, and 35 kV/us CMTI, housed in a 16-pin narrow-body SOIC (3.90 mm width) package. It uses Silicon Labs' proprietary RF-coupled isolation technology, integrating an onboard DC-DC converter on the chip so each side can be powered from a single 3.0 V to 5.5 V supply without external bypass or isolation transformers. The 'BC' channel configuration provides 6 forward channels (six in the same direction), making it suitable for unidirectional high-speed signal transfer across an isolation barrier. What is a digital isolator? A digital isolator is a semiconductor device that transfers digital signals across an isolation barrier using high-voltage capacitors, micro-transformers, or optocouplers. They replace legacy optocouplers in industrial, automotive, and medical systems where galvanic isolation is required for safety, ground-loop elimination, or noise immunity. Within the broader taxonomy, digital isolators are interface ICs (interface > isolation > galvanic isolator) and compete directly with traditional optocouplers while offering higher speed, longer lifetime, and tighter channel-to-channel matching. Key features of the SI8662BC-B-IS1R include an operating temperature range of -40C to +125C, propagation delay of approximately 18 ns typical, and an integrated shutdown mode that drops current consumption to near-zero during idle states. The device meets UL 1577, CSA, and VDE safety certification targets for reinforced insulation at 3750 Vrms. Channel-to-channel timing skew is tightly controlled, making it ideal for parallel data buses and synchronous SPI or GPIO expansion across isolation. Technically, the SI8662BC-B-IS1R uses Skyworks' CMOS-based isolation architecture with on-chip RF couplers, eliminating the need for LED-based emitters used in optocouplers. This yields a 50+ year operating life, much better than optocouplers whose LEDs degrade over time. Six independent channels share the same silicon die but are individually isolated, so a fault on one channel does not propagate to others, enhancing system-level reliability in industrial PLCs and motor drives. Typical applications include SPI/peripheral isolation in industrial PLCs, isolated GPIO interfaces in motor drives, isolated data acquisition front ends, USB isolation, isolated RS-485/RS-232 transceiver interfaces, and isolated sensor signal chains in medical and renewable-energy inverters. The SI8662BC-B-IS1R's 35 kV/us CMTI ensures robust operation in noisy environments such as IGBT motor drive switching nodes. When designing with this part, place 0.1 uF bypass capacitors as close as possible to each VDD pin (one per side) and avoid routing high-speed digital traces directly under the isolation barrier to maintain creepage and clearance requirements. Designers should also reserve at least 4 mm of external PCB creepage if the application targets reinforced insulation (VDE 0884). This page consolidates verified distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet, giving engineers a faster path to an isolation BOM decision.

詢價 聯絡我們
SI8662BD-B-IS - 6-Ch 5kVrms 150Mbps Digital Isolator | Skyworks
SI8662BD-B-IS

SI8662BD-B-IS - 6-Ch 5kVrms 150Mbps Digital Isolator | Skyworks

The Skyworks SI8662BD-B-IS is a 6-channel CMOS digital isolator rated at 5000 Vrms with a maximum data rate of 150 Mbps and a common-mode transient immunity (CMTI) of 35 kV/us, housed in a 16-pin wide-body SOIC (7.50 mm) package. Built on Skyworks' proprietary RF-based isolation architecture, the device replaces legacy optocouplers in modern industrial and renewable-energy interfaces by integrating six isolated data paths in a single IC. What is a digital isolator? A digital isolator is a semiconductor device that transfers logic signals across an isolation barrier using high-frequency carrier modulation through a silicon-dioxide dielectric, providing galvanic isolation between two circuit domains while preserving signal integrity. Digital isolators occupy the broader hierarchy of signal-conditioning ICs, sitting between simple level shifters (no isolation) and full optocoupler replacements, and they belong to the interface IC category alongside RS-485 transceivers and CAN isolators. Key features include 5000 Vrms withstand voltage, six independent unidirectional channels, propagation delay of 8 ns typical, fail-safe output behavior with a power-on reset, and support for 2.5 V to 5.5 V supply rails on both sides. The wide-body SOIC package provides the reinforced creepage and clearance required for 5 kV reinforced isolation per IEC 60747-17 / VDE 0884-11. Operating quiescent current is below the datasheet typical value, and no external initialization is required at startup, eliminating the timing race conditions found in older LED-based optocouplers. Internally, the SI8662BD-B-IS uses on-off keying (OOK) modulation with differential RF carriers transmitted across a high-voltage CMOS dielectric barrier. An integrated differential receiver on the far side reconstructs the original logic transition with deterministic propagation delay (8 ns typical, 13 ns maximum). This topology achieves >60-year continuous operating life at the rated working voltage and provides stable CMTI behavior across the full industrial temperature range. Typical applications include industrial fieldbus isolation (RS-485, RS-232, CAN), solar inverter gate driver signaling, motor control encoder interfaces, PLC digital input modules, and isolated SPI/UART links. It is also widely used in medical patient-isolated data acquisition and EV battery management system (BMS) communications where reinforced isolation is mandatory. When designing with the SI8662BD-B-IS, place 0.1 uF bypass capacitors on each VDD pin within 2 mm of the IC, and verify PCB creepage of at least 8 mm across the package body to maintain rated isolation. Avoid routing signal traces or copper pours directly under the package body, since the dielectric barrier must remain the only galvanic path between the two domains. This page synthesizes distributor pricing, drop-in Si866x-family and competitor equivalents, and practical layout guidance that is not collected in any single manufacturer document.

詢價 聯絡我們
SI8710AC-B-IS - 3.75kV Digital Isolator, 1-Ch, 15Mbps | Skyworks
SI8710AC-B-IS

SI8710AC-B-IS - 3.75kV Digital Isolator, 1-Ch, 15Mbps | Skyworks

The Skyworks (formerly Silicon Labs) SI8710AC-B-IS is a single-channel, CMOS-based digital isolator rated at 3750 Vrms with a 15 Mbps data rate and >50 kV/us typical common-mode transient immunity (CMTI), housed in an 8-pin SOIC (3.90 mm body width) package. It is a pin-compatible, drop-in upgrade for popular high-speed digital optocouplers and replaces opto-LED/phototransistor solutions with a capacitive-coupling isolation barrier. A digital isolator is a semiconductor device that transfers logic-level signals across an isolation barrier using a non-electrical coupling mechanism (capacitive, inductive, or optical), while providing galvanic isolation between grounds. In the system hierarchy, digital isolators sit above simple logic isolators and below fully integrated isolated gate drivers and isolated ADCs. They are essential whenever a logic signal must cross a safety barrier such as an IEC 61800 / IEC 60950 reinforced insulation boundary, or when ground-potential differences between subsystems would otherwise create ground loops or fault paths. Key differentiating specifications include a 60 ns typical propagation delay, 20 kV/us minimum CMTI per datasheet, 3 V to 30 V wide supply voltage range on the output side, and an open-drain (open-collector) output stage that emulates the phototransistor of a traditional optocoupler. The CMOS isolation technology eliminates the LED aging and forward-current drift that plagues optocouplers, providing a 10x lower FIT rate and stable propagation delay across the full -40C to +125C automotive temperature range. Architecturally, the Si87xx family uses proprietary capacitive isolation with on-chip encoding/decoding. An internal oscillator modulates the input logic state across the capacitive barrier, and a differential receiver reconstructs the original signal with deterministic timing. Unlike optocouplers, there is no LED, no current-transfer-ratio degradation, and no need for an input buffer network beyond a simple series resistor. Typical applications include replacement of HCPL-4506/ACPL-247/PS2801 type optocouplers in industrial PLCs, gate-driver signal isolation for IGBT/MOSFET bridges in motor drives and solar inverters, isolated SPI/UART links in factory automation, isolated status feedback in switch-mode power supplies, and AEC-Q100 automotive battery-management isolation. When designing with this part, note that the Si8710AC-B-IS uses an open-drain output that requires an external pull-up resistor (typ. 1 kohm to 10 kohm) on the output node. Designers must also provide a bypass capacitor of at least 0.1 uF close to each supply pin and keep input-side current below 10 mA per datasheet. This page synthesizes distributor pricing, drop-in Si87xx family alternatives, and practical optocoupler-replacement design notes not consolidated in the manufacturer datasheet alone.

詢價 聯絡我們
SI8710AD-B-IS - 5kV Digital Isolator, 15Mbps, SDIP-6 | Skyworks
SI8710AD-B-IS

SI8710AD-B-IS - 5kV Digital Isolator, 15Mbps, SDIP-6 | Skyworks

The Skyworks Solutions SI8710AD-B-IS is a 5 kVrms single-channel digital isolator housed in a 6-pin SDIP (0.295 inch / 7.50 mm width) wide-body package, designed as a pin-compatible drop-in replacement for popular optocouplers. It supports data rates up to 15 Mbps across a supply range of 3 V to 30 V, with a typical propagation delay of 60 ns, 20 kV/µs common-mode transient immunity (CMTI), and an open-collector output stage with 5 kV LED-emulator input. A digital isolator is a semiconductor device that transfers logic signals across a galvanic isolation barrier using high-voltage capacitors or RF/transformer coupling rather than an optocoupler's LED + photodiode path. Compared to optocouplers, CMOS-based digital isolators offer higher speed, tighter timing, lower power, and significantly better aging and temperature behavior. Digital isolators sit within the interface IC category of mixed-signal semiconductors and are the modern building block for safe signal transfer across high-voltage domains in industrial, automotive, and renewable-energy systems. The SI8710AD-B-IS integrates Skyworks' proprietary CMOS isolation technology in a wide-body SDIP-6 footprint, achieving 5000 Vrms reinforced isolation per VDE 0884-10 / UL 1577. The LED-emulator input eliminates the current-transfer-ratio (CTR) degradation that plagues optocouplers over time, while the open-collector output supports legacy 3.3 V to 30 V logic rails and bus-side pull-ups up to 30 V, simplifying system retrofits where the user is migrating away from a 6-pin DIP optocoupler. The Si87xx family is qualified to AEC-Q100 for automotive designs, supports up to 15 Mbps NRZ signaling, and delivers typical propagation delay of 60 ns with channel-to-channel matching suited to high-speed GPIO, SPI isolation, and serial communications lines. Because it is pin-compatible with industry-standard 6-pin DIP optocouplers, the SI8710AD-B-IS is often used as a modernization upgrade that improves speed, power, and reliability simultaneously. Typical applications include isolated GPIO interfaces, industrial fieldbus isolation (RS-232/RS-485, CAN, SPI), PLC I/O modules, solar inverter gate drivers, motor-control feedback paths, and battery-management system (BMS) communications. Designers also use it as a drop-in optocoupler replacement in SMPS feedback loops and digital input modules where 5 kV isolation is required. When replacing an optocoupler, verify the LED-emulator input current range matches the legacy LED forward current and confirm the open-collector output's rated voltage supports the new bus voltage. The wide-body SDIP-6 footprint matches standard 6-pin DIP optocoupler PCB land patterns, but creepage and clearance at the system level must still be reviewed for end-equipment safety certification. This page synthesizes distributor pricing, drop-in alternatives from the Si87xx family, and practical design guidance not found in the manufacturer datasheet alone.

詢價 聯絡我們
SI8710AD-B-ISR - 5kV Digital Isolator, 15Mbps, 1-Ch | GreenPeak (Skyworks)
SI8710AD-B-ISR

SI8710AD-B-ISR - 5kV Digital Isolator, 15Mbps, 1-Ch | GreenPeak (Skyworks)

The GreenPeak (Skyworks) SI8710AD-B-ISR is a single-channel CMOS digital isolator rated for 5000 Vrms galvanic isolation with a maximum data rate of 15 Mbps and 20 kV/µs common-mode transient immunity (CMTI), housed in a 6-pin wide-body SOIC (SDIP-6) package. It replaces traditional LED-based optocouplers while delivering higher reliability, lower power consumption, and tighter propagation-delay specs at a fraction of the board area. An digital isolator is a semiconductor device that transfers a logic signal across an isolation barrier using high-voltage silicon-dioxide capacitors instead of an LED-and-photodiode chain. This architecture (CMOS isolation) is part of the broader signal-isolation IC family, which sits hierarchically above simple gate drivers and below the wider category of interface ICs. By eliminating the LED, the digital isolator removes the dominant aging mechanism of optocouplers, delivering stable CTR over decades of operation in industrial environments. Key features include a propagation delay of 60 ns typical (well under one 15 Mbps UI), 25 kV/µs static CMTI, an input supply range of 3.0 V to 5.5 V, and an output supply range of 3.0 V to 5.5 V (the 'D' suffix denotes the default input = output high; the part number 'B' denotes the wide-body SDIP-6 footprint). The device integrates refresh-input duty cycle monitoring and offers reliability through CMOS isolation technology that does not degrade with time or temperature, unlike LED-based optocouplers. Architecturally, the Si87xx family uses Silicon Labs' proprietary CMOS isolation technology, where two high-voltage capacitors form a 5000 Vrms barrier. An on-chip RF carrier modulated by the input data crosses the capacitor; the receiver demodulates and reconstructs the logic level on the secondary side. Because no LED is required, this configuration does not age, eliminating CTR drift across decades and harsh thermal cycles. Typical applications include industrial fieldbus isolation (RS-485, RS-232, CAN), PLC I/O module galvanic isolation, solar inverter gate-drive interfacing, medical equipment patient-isolation barriers, and switch-mode power supply feedback paths. The 5 kV rating meets IEC 60747-17 reinforced isolation for industrial control and IEC 60950-1 reinforced insulation for IT equipment, as cited in the Si87xx data sheet. When designing with this part, pay attention to PCB creepage and clearance: the wide-body SDIP-6 footprint provides 8 mm of creepage, sufficient for most reinforced-insulation systems up to 600 V working voltage. Decouple both VDD2/VDD1 with 0.1 µF + 10 µF ceramic capacitors placed within 10 mm of each supply pin to meet the 15 Mbps eye-diagram mask. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
SI8710BC-B-IS - 1-Ch 15Mbps Digital Isolator | Skyworks
SI8710BC-B-IS

SI8710BC-B-IS - 1-Ch 15Mbps Digital Isolator | Skyworks

The Skyworks Solutions SI8710BC-B-IS is a single-channel digital isolator that delivers up to 15 Mbps data rate across a 3.75 kVrms isolation barrier in an 8-pin SOIC package. It is a pin-compatible, drop-in solid-state replacement for legacy optocouplers, providing LED-emulator CMOS input and an open-collector output with common-mode transient immunity (CMTI) of 35 kV/us. Supply voltage operates across 3 V to 30 V, simplifying integration across 3.3 V, 5 V, 12 V, and 24 V system rails. What is a digital isolator? A digital isolator is a semiconductor device that transmits logic-level signals across an isolation barrier using high-voltage capacitive or magnetic coupling rather than optical (LED + photodiode) means. Digital isolators sit within the broader power management and signal conditioning hierarchy: digital isolator -> isolation IC -> interface IC -> analog/mixed-signal semiconductor. Compared to optocouplers, CMOS-based isolators eliminate LED aging, current-transfer-ratio (CTR) degradation, and temperature-dependent gain shifts, while also consuming roughly 10x less input bias current. Key specifications include 60 ns maximum propagation delay, 3750 Vrms withstand isolation voltage (per UL 1577 standards - see datasheet), >50 kV/us typical CMTI, and a wider 3 V to 30 V supply range that supports industrial 24 V rails. The Si87xx family is built on proprietary CMOS isolation technology that yields a 10x lower FIT rate than optocouplers, producing longer service life and immune to temperature, age, and forward-current effects that plague optical solutions. The Si87xx architecture uses an on-chip oscillator to convert the DC input into an AC carrier, capacitively couples it across the isolation barrier, and reconstructs the logic level on the secondary side. The open-collector output stage requires a pull-up resistor (typically 4.7 kOhm to 10 kOhm) on the output side and supports logic translation across different voltage domains, a useful feature when bridging 3.3 V microcontrollers to 24 V industrial inputs. Typical applications include PLC digital input modules, industrial fieldbus isolation (RS-485, CAN, Profibus node isolation), switching power supply feedback path isolation, and IGBT gate-drive signal isolation in motor drives. The 15 Mbps data rate is also adequate for SPI interface isolation at modest clock rates and for low-speed serial protocol bridging. When designing with this device, note that the input is an LED emulator (not a TTL/CMOS logic input) - the datasheet specifies minimum forward current, which the engineer must respect. The output pull-up resistor value must be chosen to balance speed against power dissipation; 4.7 kOhm is a common starting point for 5 V rails. This page synthesizes Skyworks datasheet values, distributor pricing tiers, same-brand Si87xx drop-in options, and practical design notes not found in any single manufacturer document.

詢價 聯絡我們
SI8711CC-B-IS - 3.75 kV Digital Isolator, 1 Mbps, 8-SOIC | Skyworks
SI8711CC-B-IS

SI8711CC-B-IS - 3.75 kV Digital Isolator, 1 Mbps, 8-SOIC | Skyworks

The Skyworks SI8711CC-B-IS is a single-channel CMOS digital isolator that delivers 3750 Vrms isolation and 1 Mbps data rate in an 8-pin SOIC (0.154 inch / 3.90 mm width) package. Designed as a pin-compatible, drop-in upgrade for popular optocouplers, the device replaces the LED + photodetector path of an optocoupler with an RF carrier and CMOS isolation barrier. It operates from a 3.0 V to 5.5 V supply on both sides and provides open-drain output behavior with an integrated LED emulator input, enabling direct replacement of existing opto-isolated logic interfaces without firmware or schematic changes. A digital isolator is a semiconductor device that transfers logic-level signals across a galvanically isolated barrier using capacitive, inductive, or optical-emulation coupling while blocking DC and low-frequency voltage transients between the input and output domains. Digital isolators belong to the broader interface-IC hierarchy (interface IC > digital isolator > CMOS isolator > optocoupler replacement) and serve as modern, high-reliability substitutes for traditional optocouplers in industrial, telecom, and instrumentation systems. Key features include 20 kV/µs minimum common-mode transient immunity (CMTI), >50 kV/µs typical CMTI, low power consumption enabled by CMOS construction, a 10x lower FIT rate than optocouplers, and immunity to temperature, age, and forward-current drift. The 8-SOIC (0.154 inch width) footprint is PCB-compatible with industry-standard 8-pin optocouplers, allowing direct drop-in substitution on existing boards. Operating temperature range is -40 °C to +125 °C, and the device is rated for 3.75 kVrms (per UL 1577) reinforced isolation. Architecturally, the Si87xx family uses proprietary CMOS isolation technology: an RF carrier is modulated by the input logic and coupled across the internal isolation barrier, then demodulated and presented at the output as an open-drain signal that mirrors optocoupler behavior. This emulates the LED + phototransistor transfer curve so that legacy optocoupler drive circuits work without modification, while eliminating LED aging, low CTR, and slow switching speed limitations. Typical applications include isolated logic-level interfaces in industrial PLCs, isolated gate-drive feedback in motor drives and solar inverters, isolated data acquisition front-ends, isolated UART/SPI between MCU and high-voltage domains, and replacement of legacy optocouplers in telecom and instrumentation equipment. When designing in this part, verify that the upstream driver can source the Si87xx input current (typically a few mA) and that the open-drain output pull-up voltage is within the device's VDD range. Decoupling capacitors (0.1 µF ceramic) should be placed close to each supply pin. The 8-SOIC footprint allows direct solder-pad compatibility with legacy opto footprints. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that complement - but do not substitute for - the Skyworks Si87xx datasheet.

詢價 聯絡我們
SI8712AC-B-ISR - 3.75 kV Digital Isolator, 15 Mbps, SOIC-8 | Skyworks
SI8712AC-B-ISR

SI8712AC-B-ISR - 3.75 kV Digital Isolator, 15 Mbps, SOIC-8 | Skyworks

The Skyworks Solutions (formerly Silicon Labs) SI8712AC-B-ISR is a general-purpose single-channel digital isolator rated at 3750 Vrms with 15 Mbps data rate and 20 kV/µs typical common-mode transient immunity (CMTI), housed in a surface-mount 8-SOIC (0.154", 3.90 mm width) package. The -ISR suffix denotes Tape & Reel packaging. The device delivers pin-compatible, drop-in optocoupler replacement functionality in industrial and consumer applications requiring galvanic isolation between logic domains. A digital isolator is a semiconductor device that transfers logic signals across an isolation barrier using capacitive, inductive (transformer), or RF carrier coupling instead of an LED-and-phototransistor optical path. Compared with traditional optocouplers, CMOS digital isolators such as the Si87xx family typically exhibit 10x lower FIT rates, wider operating temperature ranges (-40 to +125 °C), much higher CMTI (>50 kV/µs typical), and freedom from aging and forward-current degradation effects. The Si8712 belongs to the silicon isolator category within the broader interface ICs hierarchy. Key features of the SI8712AC-B-ISR include 3750 Vrms reinforced isolation, 15 Mbps NRZ signaling capability, an open-drain / open-collector output stage (option letter "C"), and an LED-emulator input that mimics the biasing characteristics of a standard optocoupler. According to the Si87xx family datasheet, this makes the part a true drop-in alternative to popular high-speed optocouplers such as HCPL-0720, HCPL-0723, and 6N137 in PCB footprint and pinout. The Si87xx architecture uses an internal RF carrier modulated by the input logic and recovered on the isolated side, with on-chip transformers replacing the optical coupling path. This approach eliminates LED wear-out, eliminates the need for input current limiting in most cases, and consumes less board area than discrete optocouplers with the same isolation rating. Typical applications include isolated gate-drive interfaces, industrial fieldbus (RS-485, CAN, SPI) isolation, PLC I/O modules, switching power supply feedback isolation, and medical equipment patient-isolated data links. The 3.75 kV rating suits most 230 V AC mains-connected industrial systems as well as low-voltage battery management isolation. Designers should verify that downstream logic tolerates the open-collector output pull-up voltage (typically 3 to 30 V), and place a 0.1 µF bypass capacitor close to VDD on each side. The Si87xx family is footprint-compatible with industry-standard 8-pin optocouplers, allowing drop-in PCB reuse.

詢價 聯絡我們
SI8715BC-A-IS - 3.75 kV 1-Ch Digital Isolator 15 Mbps SOIC-8 | Skyworks
SI8715BC-A-IS

SI8715BC-A-IS - 3.75 kV 1-Ch Digital Isolator 15 Mbps SOIC-8 | Skyworks

The Skyworks (formerly Silicon Labs) SI8715BC-A-IS is a single-channel digital isolator in an 8-pin SOIC package that delivers 3750 Vrms of galvanic isolation, 15 Mbps of data throughput, and >50 kV/us typical common-mode transient immunity (CMTI). It is built around an RF carrier / emulated-LED architecture rather than a traditional optocoupler, which removes the aging, temperature, and forward-current degradation effects inherent to optocouplers. A digital isolator is an interface IC that transfers a high-speed digital signal across an isolation barrier while blocking DC and low-frequency transients between two grounds. The SI8715BC-A-IS is part of the Si87xx family — pin-compatible, single-channel, drop-in upgrades for popular high-speed digital optocouplers — and offers roughly 10x lower FIT rate, wider temperature tolerance, and higher CMTI than a discrete opto/LED pair. Within the system taxonomy it belongs to digital isolators -> interface isolators -> isolation ICs -> power management & interface signal chain. Key features include 3.75 kVrms withstand voltage per UL 1577, 2.5 V to 5.5 V logic-side supply, 50 ns typical propagation delay, low input current draw, and a wide industrial -40C to +125C operating range. The 8-SOIC body is the industry-standard optocoupler footprint, so legacy optocoupler designs can be retrofitted without PCB rework. Architecturally, the device uses an on-chip RF oscillator that feeds a differential capacitive or transformer isolation barrier, with a demodulator and Schmitt-triggered output stage reproducing the input logic level on the load-side supply rail. The emulated-LED front end draws a defined bias current at the input pin, so it can be driven directly from a microcontroller GPIO without the resistor-divider network that an optocoupler requires. Typical applications are PLC digital-input modules, industrial sensor isolation, isolated gate-driver signal paths, switched-mode power supply (SMPS) feedback, and isolated SPI / UART links. The part is also a drop-in optocoupler replacement in solid-state relays, motor-control I/O isolation, and medical-device signal isolation where regulatory 5 kV isolation is not required but 3.75 kVrms is sufficient. When designing in, note that input pin 2 must be tied through a resistor to the driving logic source because the input is a current-driven emulated LED, not a CMOS logic input. Add a 0.1 uF decoupling capacitor close to each supply pin to ride through fast CMTI events, and avoid extending traces past the package body to maintain the rated isolation. This page aggregates distributor pricing, same-brand Si87xx drop-in alternatives, and practical PCB/EMI design guidance that is not consolidated in the manufacturer datasheet, giving engineers a faster path from schematic to qualified BOM.

詢價 聯絡我們
SI8901B-A01-GS - 10-bit Isolated I2C ADC, 2.5kV | Skyworks
SI8901B-A01-GS

SI8901B-A01-GS - 10-bit Isolated I2C ADC, 2.5kV | Skyworks

The Skyworks Solutions (formerly Silicon Labs) SI8901B-A01-GS is a 2.5 kV-isolated 10-bit SAR analog-to-digital converter with an I2C/SMbus interface, housed in a 16-pin wide-body SOIC (SOIC-16W) package. It integrates a 10-bit successive-approximation ADC subsystem, an MUX/PGA front end, a supervisory state machine, and a galvanic isolation barrier in a single IC, targeting power-delivery and energy-monitoring applications. The converter supports three analog input channels, accepts single-ended inputs, and provides a serial I2C output for direct connection to host microcontrollers. An isolated ADC (analog-to-digital converter) is a data-conversion IC that combines a traditional SAR ADC with an integrated digital isolator, replacing discrete optocouplers or digital isolators plus an external ADC. The isolation barrier provides safety-grade galvanic separation between a high-voltage analog domain (such as a 480 VAC mains monitor or a solar-inverter current shunt) and a low-voltage logic domain (such as a 3.3 V MCU). Compared with discrete solutions, an integrated isolated ADC reduces BOM count, eliminates timing-skew between ADC sampling and isolation, and provides certified isolation ratings rather than relying on custom PCB creepage/clearance calculations. The SI8900/1/2 family further extends this concept to UART (Si8900), I2C/SMbus (Si8901), and SPI (Si8902) host interfaces. Key features include 2.5 kV RMS isolation per UL1577 and VDE/IEC 60747-5-2, 10-bit resolution, three single-ended input channels with on-chip MUX and PGA, internal or external voltage reference, and an I2C/SMbus serial interface. The device operates from a 2.7 V to 5.5 V analog supply and a 3.0 V to 5.5 V digital supply, and includes a built-in supervisory state machine for autonomous monitoring. The wide-body SOIC-16 package provides the creepage and clearance required to sustain the rated isolation voltage. Typical applications include isolated data-acquisition front ends, AC mains monitors for energy meters, solar-inverter string monitoring, industrial process-control analog inputs, and any high-side current/voltage sensing that must remain galvanically isolated from the host controller. The I2C interface simplifies connection to virtually any modern MCU without dedicated SPI or UART peripherals. When designing with this part, place 0.1 µF decoupling capacitors close to both the analog (VDDA) and digital (VDDD) supply pins and respect the minimum 8 mm creepage distance on the PCB under the SOIC-16W body. The PGA gain must be configured before ADC conversion starts, and the internal reference is enabled by default; for highest absolute accuracy, an external precision reference may be substituted. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Skyworks datasheet.

詢價 聯絡我們