積體電路

子分類

📁 ADC/DAC 3,100+ 產品 📁 放大器 IC 1,700+ 產品 📁 音訊編解碼器 18 產品 📁 音訊 IC 2 產品 📁 時脈與計時 640+ 產品 📁 Comparator ICs 1 產品 📁 DSP 1,100+ 產品 📁 資料擷取 IC 2 產品 📁 數位電位器 4 產品 📁 顯示驅動器與控制器 1 產品 📁 FPGA 與 CPLD 7,100+ 產品 📁 介面 IC 3,100+ 產品 📁 LED 驅動器 1 產品 📁 邏輯 IC 450+ 產品 📁 記憶體 IC 870+ 產品 📁 微控制器 20,000+ 產品 📁 微處理器 4 產品 📁 馬達驅動器 1 產品 📁 其他 1 產品 📁 感測器與偵測器介面 1 產品 📁 特殊用途 IC 15 產品 📁 視訊 IC 13 產品

產品（38,000+)

STM8S208CBT6 - 24MHz 8-Bit MCU, 128KB Flash | STMicroelectronics
STM8S208CBT6

STM8S208CBT6 - 24MHz 8-Bit MCU, 128KB Flash | STMicroelectronics

The STMicroelectronics STM8S208CBT6 is a 24 MHz performance-line 8-bit microcontroller with 128 KB of Flash program memory, integrated EEPROM, and a 48-pin LQFP package. It combines a 10-bit ADC, multiple timers, two UART interfaces, SPI, I²C, and CAN connectivity for compact embedded control systems operating from 3.3 V or 5 V. An 8-bit microcontroller is a microprocessor optimized for embedded control tasks such as sensing, actuator control, communications, and system supervision. The STM8S belongs to the STM8S performance line and combines an 8-bit CISC architecture with dedicated peripheral interfaces. This hierarchy places it above basic 8-bit controllers in performance while retaining the simple programming model and cost profile associated with embedded microcontrollers. The principal device characteristics are a 24 MHz operating frequency, 128 KB of Flash memory, and a 48-pin LQFP package. Integrated EEPROM supports nonvolatile parameter storage, while the 10-bit ADC provides a practical interface for analog sensors. Two UARTs support serial diagnostics or external-module communication, and the SPI and I²C interfaces allow connection to displays, sensors, memory, and other digital peripherals. CAN support makes the device relevant to distributed industrial and automotive-style control networks. The STM8S208CBT6 integrates communication and timing resources in one package, reducing the need for external interface controllers. Its timer resources support periodic measurement, pulse generation, motor-control-oriented timing, and input capture functions. The combination of CAN, two UART channels, SPI, and I²C permits multiple independent communication paths while retaining a single embedded controller. Exact SRAM capacity, EEPROM capacity, ADC conversion rates, and individual timer counts must be confirmed in the manufacturer datasheet before final design sign-off. Typical applications include industrial sensor nodes, building-control modules, motor and relay controllers, automotive accessories, CAN-connected equipment, and compact consumer products. Its 48-pin package provides more I/O and peripheral connectivity than smaller STM8 devices, making it appropriate when a design needs both communication breadth and a meaningful number of external connections. The trade-off is a larger footprint and board area than 20-pin or 32-pin alternatives. For PCB design, assign pins from the exact STM8S208CB datasheet rather than inferring them from a generic STM8 symbol. Preserve the device’s decoupling requirements, provide a clean analog reference for the ADC, and route communication interfaces away from switching nodes. Confirm clock configuration, boot behavior, programming access, and unused-pin handling before committing the layout to production. This product record combines the manufacturer’s STM8S208CB family information with package, interface, application, and substitution guidance. It highlights the engineering trade-offs among same-footprint STM8S options and provides practical design context for teams selecting a 24 MHz, 128 KB Flash 8-bit controller for CAN, serial, analog, and embedded-control designs.

詢價 聯絡我們
STM8S208R8T6 - 8-Bit 24MHz 64KB Flash MCU | STMicroelectronics
STM8S208R8T6

STM8S208R8T6 - 8-Bit 24MHz 64KB Flash MCU | STMicroelectronics

The STM8S208R8T6 is a high-performance 8-bit microcontroller from STMicroelectronics' STM8S series, featuring a 24 MHz CPU core, 64KB of Flash program memory, and 6KB of RAM. It is housed in a 64-pin LQFP package (10x10 mm) and operates from a 3.3V or 5V supply, making it suitable for a wide range of industrial and consumer applications. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data bus, integrating a CPU, memory, and peripherals. The STM8S series is a family of 8-bit MCUs from STMicroelectronics, positioned between low-end 8-bit devices and 32-bit ARM-based MCUs. It offers a cost-effective solution for applications requiring moderate processing power, rich peripherals, and low power consumption. The STM8S208R8T6 belongs to the performance line, which provides higher clock speeds and more memory compared to access line devices. Key features include a 24 MHz maximum CPU frequency with 0 wait states, 64KB of Flash memory, 6KB of RAM, and 2KB of EEPROM. It integrates a 10-bit ADC with up to 16 channels, multiple 16-bit timers, two UARTs, SPI, I2C, and a CAN interface. The device also includes a watchdog timer, brown-out reset, and low-power modes, enhancing reliability and energy efficiency. The STM8S208R8T6 is built on ST's advanced 8-bit core architecture, which delivers up to 20 MIPS at 24 MHz. It features a Harvard architecture with separate instruction and data buses, allowing simultaneous instruction fetch and data access. The integrated EEPROM enables non-volatile data storage without external components, and the CAN interface supports robust communication in automotive and industrial networks. Typical applications include industrial control systems, home appliances, automotive body electronics, and communication modules. The CAN interface makes it ideal for automotive networks, while the rich timer and ADC peripherals suit motor control and sensor interfacing. The wide operating voltage range (2.95V to 5.5V) ensures compatibility with both 3.3V and 5V logic systems. When designing with this MCU, ensure proper decoupling of the power supply and a stable clock source. The device supports multiple clock sources, including an internal RC oscillator and external crystal. For low-power applications, utilize the halt and active-halt modes to reduce current consumption. The CAN interface requires an external transceiver, such as the TJA1050, for physical layer connectivity.

詢價 聯絡我們
STM8S208RBT3 - 24MHz 128KB 8-Bit MCU | STMicroelectronics
STM8S208RBT3

STM8S208RBT3 - 24MHz 128KB 8-Bit MCU | STMicroelectronics

The STMicroelectronics STM8S208RBT3 is an 8-bit STM8S performance-line microcontroller with a 24 MHz CPU, 128 KB of Flash program memory, integrated EEPROM, a 10-bit ADC, and communication peripherals including two UARTs, SPI, I²C, and CAN. The device is supplied in a 64-LQFP package measuring 10 x 10 mm and is intended for compact embedded-control systems. An 8-bit microcontroller is a programmable semiconductor containing a processor core, memory, and integrated peripherals on one device. STM8 devices belong to the broader microcontroller and embedded-processor hierarchy, combining an 8-bit CISC-oriented architecture with deterministic real-time control peripherals. The STM8S208 performance line is positioned above smaller STM8 families by offering more Flash memory and a broad selection of communication and timing resources. Key features of the STM8S208RBT3 include operation at up to 24 MHz, 128 KB of Flash, integrated EEPROM, a 10-bit analog-to-digital converter, multiple timers, 38 I/O ports, and support for UART, SPI, I²C, and CAN communication. These resources allow the MCU to consolidate several discrete functions on a single device and reduce component count in industrial controls, communications equipment, access systems, and embedded measurement products. The STM8S architecture supports a supply range of 3 V to 5.5 V according to the verified distributor data. Its integrated EEPROM provides nonvolatile data storage without requiring an external memory chip, while the 10-bit ADC supports analog sensor acquisition. Two UART channels enable asynchronous serial connectivity, SPI supports higher-speed peripherals, I²C supports external sensors and EEPROMs, and CAN supports industrial network nodes. Typical applications include industrial automation controllers, CAN-connected equipment, motor and relay control, environmental monitoring, access-control terminals, serial data acquisition, and compact consumer appliances. The 64-LQFP package provides enough I/O for external sensors, displays, transceivers, and actuators while remaining practical for leaded PCB assembly and prototype development. Designers should verify the exact pin assignment, electrical limits, oscillator requirements, reset circuit, and decoupling recommendations against the STM8S208RB manufacturer documentation before layout. The 3 V to 5.5 V supply requirement means external interface levels and sensor voltages must remain compatible with the MCU pins used. This product page consolidates verified manufacturer and distributor specifications, same-package replacement guidance, interface coverage, and practical engineering considerations into one reference for engineers evaluating the STM8S208RBT3.

詢價 聯絡我們
STM8S208RBT6 - 8-Bit 24MHz 128KB Flash MCU | STMicroelectronics
STM8S208RBT6

STM8S208RBT6 - 8-Bit 24MHz 128KB Flash MCU | STMicroelectronics

STMicroelectronics STM8S208RBT6 is an 8-bit STM8S performance-line microcontroller operating at 24MHz with 128KB of Flash program memory and up to 20MIPS throughput. It is supplied in a 64-pin LQFP package and supports 3.3V and 5V operation according to the verified product listings. Integrated peripherals include a 10-bit ADC, timers, two UARTs, SPI, I2C, and CAN. An STM8S microcontroller belongs to the 8-bit embedded-control segment of the semiconductor hierarchy. These devices combine a compact CISC core, embedded nonvolatile memory, analog conversion, serial communication, and timing peripherals in one package. They are used where deterministic control, low system complexity, and economical embedded intelligence are more important than the processing power and memory bandwidth of a 32-bit Cortex-M MCU. The STM8S208RBT6 combines 128KB Flash with a 24MHz clock, delivering 20MIPS as identified by Mouser. Its integrated 10-bit ADC supports measurements without a separate converter, while two UARTs, SPI, I2C, and CAN provide several paths for sensors, displays, industrial networks, and external controllers. This interface density makes the device suitable for compact industrial controllers, motor-control helpers, communication gateways, and embedded measurement products. As an STM8S20xxx performance-line part, the device belongs to a family offered from 32KB through 128KB Flash. The selected 128KB configuration provides more program space than lower-density variants while preserving the familiar STM8S peripheral and software environment. This supports protocol stacks, application logic, logging, and parameter handling in a single embedded controller. Typical applications include CAN-connected industrial nodes, sensor acquisition and control, motor or actuator supervision, and compact communication equipment. The CAN interface is valuable when the design must participate in a bus network, while the ADC and multiple serial interfaces support local sensing. Designers should still verify timing, peripheral availability, pin multiplexing, and memory requirements in the manufacturer documentation before finalizing firmware. The principal design consideration is that software compatibility does not guarantee an unconditional drop-in replacement. Firmware startup code, interrupt vectors, peripheral configuration, clock settings, and PCB pad assignments must all be checked. For new designs, the 128KB Flash capacity and broad mixed-signal connectivity can reduce external components, but the 64-pin LQFP footprint requires adequate board area and careful routing of analog and communication signals. This product page combines verified manufacturer, distributor, and cross-reference information with practical design guidance. It helps engineers assess the STM8S208RBT6, compare documented same-family options, understand its peripherals, and plan sourcing and PCB integration without presenting unsupported electrical values.

詢價 聯絡我們
STM8S903F3M3 - 16MHz 8-Bit MCU | STMicroelectronics
STM8S903F3M3

STM8S903F3M3 - 16MHz 8-Bit MCU | STMicroelectronics

STMicroelectronics STM8S903F3M3 is an 8-bit STM8S-series microcontroller rated for operation up to 16 MHz, with 8 KB of Flash program memory and 1 KB of RAM in a 20-pin SOIC package. The device also includes 640 bytes of true data EEPROM, a 10-bit ADC, two timers, UART, SPI, and I2C interfaces. Its operating supply range is 2.95 V to 5.5 V, while 16 GPIO pins support embedded control and communication tasks. An 8-bit microcontroller is a compact embedded processor designed to execute firmware, read sensors, control outputs, and manage communication interfaces. The STM8S903F3 belongs to the broader STM8 embedded and industrial-control ecosystem. Compared with application-specific logic, a microcontroller consolidates processing, memory, analog measurement, timing, and serial communications into one device, reducing board area and simplifying product maintenance. The 16 MHz operating frequency provides useful processing headroom for real-time control, while 8 KB of Flash stores application code and 640 bytes of EEPROM preserve frequently changed parameters such as calibration values or configuration data. The 10-bit ADC supports analog sensor acquisition, and the two timers help implement periodic tasks, pulse measurement, motor timing, or basic PWM-related functions. UART, SPI, and I2C expand the available connection options for external controllers, sensors, displays, and transceivers. The STM8S core combines an 8-bit architecture with integrated peripheral blocks, allowing firmware to handle sensing and communications without separate interface controllers. Two supply rails—VDD and VDDA—support the digital and analog sections, while the 2.95 V to 5.5 V operating range accommodates common embedded supply conditions. The part includes low-power, power-on, and power-down reset behavior described for the STM8S903F3 family. Typical uses include industrial control modules, compact instrumentation, motor-control front ends, metering equipment, IoT sensor nodes, and cost-sensitive consumer or automotive electronics. The UART is useful for external configuration or diagnostics, SPI supports faster peripheral communication, and I2C accommodates low-speed sensors and memory devices. PCB design should account for analog and digital supply decoupling, stable grounding, and programming access. Place the required input and output capacitors close to their associated pins, route analog inputs away from fast switching nodes, and use a clean ground strategy to reduce ADC noise. Confirm the exact pin function and package dimensions against the manufacturer datasheet before layout release. This page consolidates the manufacturer specifications, interface capabilities, sourcing guidance, and design considerations engineers need to evaluate the STM8S903F3M3 for a new embedded design.

詢價 聯絡我們
STM8S903F3M6 - 16MHz 8KB 8-Bit MCU | STMicroelectronics
STM8S903F3M6

STM8S903F3M6 - 16MHz 8KB 8-Bit MCU | STMicroelectronics

The STMicroelectronics STM8S903F3M6 is an 8-bit STM8S-series microcontroller operating at 16 MHz, with 8 KB of Flash memory, 16 I/O ports, and a 20-SOIC package. According to the verified distributor data, it is available in a 20-SO package and is identified as an active, RoHS-compliant device with a 2.95 V to 5.5 V supply-voltage range. What is an 8-bit microcontroller? An MCU is a semiconductor device that combines a processor core, program memory, data memory, and peripherals on one integrated circuit. The STM8S903F3M6 belongs to the 8-bit MCU -> embedded microcontroller -> semiconductor hierarchy and is intended for compact control, measurement, and communication systems where a dedicated processor, memory, and serial interfaces are required. Verified specifications identify 8 KB of Flash memory, 1 KB of RAM, 640 bytes of EEPROM, a 10-bit ADC, two timers, UART, SPI, and I²C. These peripherals make the device suitable for sensor acquisition, actuator control, industrial instrumentation, and low-cost embedded products. The 16 MHz clock provides the processing headroom needed for basic control loops and serial data handling, although the verified data does not specify the complete peripheral timing or ADC accuracy. The STM8S903F3M6 uses a 20-SOIC package, also described as a 0.295-inch, 7.50 mm-width SOP package in the verified distributor data. The SOIC outline is a surface-mount package with gull-wing leads, making it suitable for conventional PCB assembly and prototype-to-production transfer. The package pinout and exposed thermal-pad details are not included in the supplied verified data, so the pinout is reported as null rather than inferred. Typical applications include compact industrial controllers, low-power sensor nodes, simple motor or relay-control boards, data-acquisition modules, UART-to-digital bridges, and small SPI or I²C peripheral boards. The STM8 family can be paired with external sensors and communication transceivers, while the integrated ADC supports analog measurement. Final firmware support should be confirmed with the applicable STMicroelectronics development tools and device documentation. For PCB design, preserve the manufacturer's recommended decoupling and grounding layout, and verify all peripheral pins, reset behavior, clock requirements, and package dimensions against the official datasheet before production. This page combines verified distributor specifications, package data, sourcing information, and engineering-oriented application guidance without treating unverified details as guaranteed specifications.

詢價 聯絡我們
STM8S903F3P3 - 16MHz 8-Bit MCU, 8KB Flash | STMicroelectronics
STM8S903F3P3

STM8S903F3P3 - 16MHz 8-Bit MCU, 8KB Flash | STMicroelectronics

The STMicroelectronics STM8S903F3P3 is an 8-bit STM8S-series microcontroller with a 16 MHz core, 8 KB of Flash program memory, 1 KB of RAM, and 640 bytes of EEPROM in a 20-pin TSSOP package. Its integrated peripherals include a 10-bit ADC, two timers, UART, SPI, and I2C interfaces. An 8-bit microcontroller is a compact embedded-processing component designed for control-oriented products that monitor inputs, operate actuators, and communicate with external devices. The STM8S product type belongs to the hierarchy of microcontroller, embedded processor, semiconductor, and integrated-circuit devices. The STM8S903 access line combines an economical 8-bit architecture with integrated data EEPROM and conventional serial interfaces, making it suitable for compact industrial controllers, measurement instruments, and embedded accessories. The principal system benefits are 8 KB of nonvolatile program storage, 1 KB of volatile data memory, and 640 bytes of true data EEPROM. The 10-bit ADC supports analog measurements, while two timers support timing, pulse generation, and basic motor or LED control functions. UART, SPI, and I2C connectivity allows the MCU to communicate with sensors, displays, transceivers, and external nonvolatile memories without requiring a separate interface controller. The STM8S903F3 operates from a 3.3 V or 5 V supply and is specified for temperatures from -40°C to +125°C. Its 20-pin TSSOP package supports compact surface-mount assemblies while exposing the core control, analog, timing, and communication functions. The STM8S903F3 family combines an 8-bit CPU with a mixed-signal peripheral set designed for cost-sensitive embedded systems that need deterministic control and moderate communication bandwidth. Typical applications include industrial control panels, digital thermometers, environmental monitoring stations, compact motor controllers, sensor-interface modules, and communication-enabled embedded accessories. In each case, the MCU can acquire analog inputs, execute control logic, store operating parameters, and update external peripherals through its integrated communication interfaces. A 16 MHz operating rate supports responsive polling and control without a higher-complexity processor core. When designing the PCB, reserve the 20-pin TSSOP footprint and route power, ground, programming signals, reset, and decoupling according to the manufacturer pin-description table. Place the supply bypass capacitor close to the device and use the pin table when assigning alternate-function signals. Firmware and peripheral configuration should be checked against the STM8S903F3 datasheet and the STM8 toolchain documentation before production release. This product record combines manufacturer specifications, orderable-part information, package details, application guidance, and a structured drop-in comparison. It is intended to help engineers evaluate the STM8S903F3P3 for embedded control designs and to request current commercial availability through the page's Request a Quote form.

詢價 聯絡我們
STM8S903F3P6 - 16MHz 8-Bit MCU | STMicroelectronics
STM8S903F3P6

STM8S903F3P6 - 16MHz 8-Bit MCU | STMicroelectronics

STMicroelectronics STM8S903F3P6 is an 8-bit STM8S-series microcontroller operating at up to 16 MHz, with 8 KB of Flash program memory and a 20-TSSOP package. The device operates from 2.95 V to 5.5 V and provides 1 KB of RAM, 640 bytes of true EEPROM, a 10-bit ADC, two timers, UART, SPI, and I²C connectivity. It is designed for compact embedded-control systems requiring mixed analog and digital functions without a higher-cost 32-bit MCU. An 8-bit microcontroller is a programmable semiconductor containing a processor core, nonvolatile program memory, data memory, and integrated peripherals. Within the hierarchy of embedded semiconductors, an MCU is below a microprocessor in processing capability but combines greater control simplicity with lower system cost and power use. The STM8S903F3 belongs to STMicroelectronics’ STM8S access line and targets cost-sensitive consumer, appliance, and industrial-control applications. Key features include 8 KB of Flash, 1 KB of RAM, and 640 bytes of EEPROM, allowing firmware, working data, and nonvolatile parameters to be consolidated in one device. The 10-bit ADC supports analog measurement, while two timers support timing and periodic control functions. UART, SPI, and I²C interfaces cover serial communication, sensor connectivity, and expansion to external ICs. The 2.95 V to 5.5 V supply range accommodates both 3.3 V and 5 V system environments. The STM8S903F3 architecture combines an 8-bit STM8 core with dedicated peripheral resources and true data EEPROM. Its 16 MHz maximum clock rate provides sufficient processing bandwidth for control loops, user-interface scanning, communications, and low-complexity signal processing. At the same time, the 20-TSSOP package limits board footprint, making it practical for compact embedded products. Detailed pin-level functions and electrical limits should be confirmed against the manufacturer datasheet before layout release. Typical uses include appliance control, small industrial controllers, digital input and output modules, sensor interfaces, compact timers, and embedded communication nodes. The STM8S903F3P6 is particularly suitable when a design requires several serial interfaces alongside analog sensing but does not justify the software complexity or cost of a 32-bit MCU. Its integrated EEPROM is useful for retaining configuration data, calibration values, or counters without an external memory component. Designers should confirm the exact 20-TSSOP land pattern, pin multiplexing, oscillator connections, reset implementation, and peripheral pin assignments using the official datasheet. Decoupling and signal-integrity layout should follow the manufacturer recommendations, while software validation should include startup, clock configuration, ADC accuracy, timer behavior, and communications under expected bus loading. The broad 2.95 V to 5.5 V range does not remove the need to verify every peripheral and I/O condition at the minimum and maximum system voltages.

詢價 聯絡我們
STM8S903K3B6 - 16MHz 8-Bit MCU with 8KB Flash | STMicroelectronics
STM8S903K3B6

STM8S903K3B6 - 16MHz 8-Bit MCU with 8KB Flash | STMicroelectronics

STMicroelectronics STM8S903K3B6 is an 8-bit STM8S-series microcontroller with a 16 MHz maximum clock, 8 KB Flash program memory, 1 KB RAM, 640 bytes EEPROM, and a 10-bit ADC in a 32-pin SDIP package. The device also provides 16 I/O ports, two timers, UART, SPI, and I²C interfaces for compact embedded control systems. Its operating supply range is 2.95 V to 5.5 V. A microcontroller is a programmable integrated circuit containing a CPU core, memory, and peripherals that execute firmware and interact with external hardware. The STM8S903K3 belongs to the STM8 access-line family, which combines an 8-bit core, integrated nonvolatile data EEPROM, and mixed-signal peripherals in a relatively small package. It is intended for cost-sensitive embedded products that need more capability than a basic logic controller without adopting a higher-performance 32-bit MCU. The STM8S903K3B6 provides 8 KB of Flash for program storage, 1 KB of RAM for working data, and 640 bytes of true EEPROM for parameter retention. Its 10-bit ADC supports analog measurements, while two timers support timing and periodic control functions. UART, SPI, and I²C provide three distinct communication paths for external sensors, actuators, displays, and serial peripherals. The 16 MHz clock enables predictable execution of control loops and interrupt-driven firmware. STMicroelectronics describes the STM8S903K3/F3 access line as an 8-bit MCU family offering 8 Kbyte Flash program memory and integrated true data EEPROM. The target device is identified by the STM8S903K3 ordering code and B6 package/temperature suffix. The verified product information specifies a 2.95 V to 5.5 V supply range, a 16 MHz clock, and an operating lifecycle status of ACTIVE. Typical uses include compact industrial controllers, sensor-interface modules, appliance controls, communication transceivers, low-cost instrumentation, and general-purpose embedded products. The combination of ADC, timers, EEPROM, and serial interfaces permits a single controller to acquire analog data, execute deterministic timing functions, preserve calibration values, and communicate with a host or peripheral device. Designers should budget PCB area for the 32-pin SDIP footprint and confirm that the selected schematic uses only functions and pin assignments supported by the exact STM8S903K3 variant. Power-supply decoupling, programming access, reset behavior, and analog-input conditioning should be validated against the manufacturer datasheet before layout release. Because the search excerpts do not provide the complete pin map, a new design must not infer pin assignments from a similarly named STM8 device. This page consolidates verified manufacturer and distributor specifications, lifecycle information, interface capabilities, and package details with selection guidance and practical design cautions. It also distinguishes confirmed same-package alternatives from candidates that require additional engineering verification, helping engineers avoid treating broadly similar MCUs as automatic drop-in replacements.

詢價 聯絡我們
STM8S903K3T6 - 8-bit MCU, 8KB Flash, 16MHz | STMicroelectronics
STM8S903K3T6

STM8S903K3T6 - 8-bit MCU, 8KB Flash, 16MHz | STMicroelectronics

The STM8S903K3T6 is an 8-bit microcontroller from STMicroelectronics' STM8S access line, featuring 8 Kbytes of Flash program memory, 1 Kbyte of RAM, and 640 bytes of true data EEPROM. It operates at a clock speed of 16 MHz and is supplied in a 32-pin LQFP package, offering a compact solution for a wide range of embedded control applications. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit central processing unit (CPU), memory, and programmable input/output peripherals. It is the foundational building block in the hierarchy of embedded systems, sitting below 16-bit and 32-bit MCUs in processing power but offering lower cost, lower power consumption, and simpler programming. The STM8S903K3T6 belongs to the STM8S family, which is designed for general-purpose industrial and consumer applications, bridging the gap between simple 8-bit controllers and more complex 32-bit processors. Key features of the STM8S903K3T6 include a 10-bit analog-to-digital converter (ADC) with up to 7 multiplexed channels, two 16-bit timers, a UART for serial communication, an SPI interface, and an I2C interface. The device also integrates a true data EEPROM with read-while-write capability, enabling non-volatile data storage without external components. The supply voltage range of 2.95V to 5.5V allows operation from standard 3.3V and 5V power rails, making it versatile for mixed-voltage systems. The STM8S903K3T6 is built on ST's advanced 8-bit core architecture, which delivers up to 16 MIPS at 16 MHz, providing efficient execution of control algorithms. The integrated EEPROM and robust clock management, including an internal RC oscillator and optional external crystal, simplify system design by reducing external component count. The device also features low-power modes, including Active-Halt and Halt modes, to minimize energy consumption in battery-powered applications. Typical applications include industrial control systems, home automation, consumer electronics, and automotive body electronics. The combination of analog and digital peripherals, along with the wide operating voltage range, makes it suitable for sensor interfacing, motor control, and communication bridging tasks. The 32-pin LQFP package provides a good balance between I/O count and board space, supporting compact PCB layouts. When designing with the STM8S903K3T6, ensure proper decoupling of the VDD and VDDA pins with 100nF capacitors placed close to the device. The internal RC oscillator is accurate to ±1% over temperature, but for applications requiring precise timing, an external crystal can be connected to the OSC_IN and OSC_OUT pins. The device's EEPROM endurance is rated for 100,000 write/erase cycles, making it suitable for frequent data logging applications.

詢價 聯絡我們
STM8S903K3U6 - 16MHz 8-Bit MCU with 8KB Flash | ST
STM8S903K3U6

STM8S903K3U6 - 16MHz 8-Bit MCU with 8KB Flash | ST

The STMicroelectronics STM8S903K3U6 is an 8-bit STM8S microcontroller with a 16 MHz clock, 8 KB of Flash program memory, 1 KB of RAM, 640 bytes of true EEPROM, and a 10-bit ADC in a 32-pin UFQFPN package measuring 5 x 5 mm. It operates from 2.95 V to 5.5 V and provides 16 I/O ports, two timers, UART, SPI, and I2C interfaces for compact embedded-control designs. An 8-bit microcontroller is a compact embedded-processing component designed around a simple central processing unit, program memory, working memory, and integrated peripherals. The STM8S family belongs to the broader hierarchy of microcontrollers, embedded processors, and semiconductors. Its combination of integrated Flash, true EEPROM, analog conversion, and serial interfaces makes it useful for cost-sensitive appliance control, industrial sensing, compact instrumentation, and low-to-moderate-speed communication equipment. Key features include 8 KB of Flash program memory, 1 KB of RAM, and 640 bytes of integrated true data EEPROM. The device supports a 16 MHz maximum clock and includes a 10-bit analog-to-digital converter, two timers, one UART, SPI, and I2C. Its operating voltage of 2.95 V to 5.5 V supports both 3.3 V and 5 V systems, while a temperature range of -40°C to +85°C covers common industrial and commercial environments. The STM8S903K3/F3 access-line architecture emphasizes performance, robustness, and reduced system cost. Flash permits in-system program storage, true EEPROM retains calibration or configuration data without external memory, and the ADC provides an economical path for analog measurement. The 32-pin UFQFPN package also offers fine-pitch external connectivity for sensors, actuators, displays, and communication transceivers, although its 0.5 mm pitch requires careful PCB assembly and inspection. Typical applications include sensor nodes, appliance controllers, compact industrial interfaces, low-speed data loggers, and embedded modules requiring UART, SPI, or I2C connectivity. Designers can connect analog inputs to the 10-bit ADC, use the timers for periodic measurement or output generation, and retain operating parameters in EEPROM. A UART bridge or level translator can extend the device into RS-232 or RS-485 systems. The primary design consideration is PCB implementation. A 32-pin UFQFPN package requires a land pattern capable of 0.5 mm pitch routing, adequate solder paste coverage, and careful control of thermal and electrical conditions. Firmware should also verify the device-specific reset behavior, clock configuration, peripheral mapping, and ADC calibration sequence against the manufacturer documentation before production. This page consolidates verified manufacturer specifications, distributor availability, procurement information, interface guidance, and same-footprint replacement analysis. It is intended to provide engineering context beyond a basic distributor listing while clearly identifying data that requires confirmation from the manufacturer datasheet.

詢價 聯絡我們
STMP3770XXBJEA2N - i.MX233/235 Audio/Video Decoder SoC | NXP
STMP3770XXBJEA2N

STMP3770XXBJEA2N - i.MX233/235 Audio/Video Decoder SoC | NXP

The NXP (formerly Freescale Semiconductor) STMP3770XXBJEA2N is a fifth-generation audio/video decoder SoC from the STMP3700 series, designed for portable media players, digital photo frames, and consumer multimedia appliances. It integrates an ARM926EJ-S CPU core with vector floating-point unit (VFP), hardware video decoding for H.264/MPEG-4/H.263/WMV9/VC-1 at D1 (720x480) resolution, and dedicated audio processing for MP3, WMA, AAC, Ogg Vorbis, and FLAC. The device is offered in a compact BGA package and is qualified for consumer-grade temperature operation. This particular MPN (XXBJEA2N) is a customer-specific suffix variant; full datasheets are available only to qualified customers under NXP NDA due to the device's use in commercial media-player products. What is an audio/video decoder SoC? An SoC (System-on-Chip) decoder is a highly integrated IC that combines a CPU, hardware video decoder, audio DSP, memory controller, peripheral interfaces, and power management in one package. SoC decoders occupy the third tier of the consumer multimedia hierarchy: general-purpose SoCs -> application-specific media SoCs -> STMP3700-family decoders. By consolidating decoding, processing, and I/O functions, these devices replace a discrete 4-6 chip set that would otherwise be required to build a portable player, reducing BOM cost and PCB area by 60-70%. Key features of the STMP3770XXBJEA2N include a hardware video pipeline supporting 720x480 D1 resolution at 30fps, a 32-bit LPDDR/DDR memory interface, integrated USB 2.0 HS OTG, NAND flash controller with ECC, I2S/PCM audio interfaces, and a 12-bit ADC for touch-screen/keypad support. The STMP3770 family also features an integrated Li-Ion battery charger and power-path management block. Architecturally, the device pairs the ARM926EJ-S host CPU (which runs the system kernel, file system, and user interface) with a dedicated media accelerator that offloads codec work. This heterogeneous compute approach yields long battery life in portable applications while delivering full-D1 video decode at low MHz - critical for thermal-limited, fanless enclosures. Typical applications include portable media players (PMP), digital photo frames, portable DVD players, GPS devices with video playback, e-book readers with audio, and connected home audio docks. Each application benefits from the integrated codec support and low-power operation. The STMP3700 series was a dominant SoC for low-cost media players from approximately 2009-2014. When designing with this part, note that source code, board support packages (BSP), and full datasheets are gated under NXP NDA; third-party BSPs (such as the Rockbox port) exist for hobbyist use. Designers should verify lead-time and minimum order quantities before committing to a new design because the part is in mature/end-of-life status. This page synthesizes distributor stock from DigiKey, Octopart, and JAK Electronics, cross-references available substitute listings, and consolidates practical design notes not found in a single manufacturer datasheet to help engineers and sourcing specialists make an informed decision.

詢價 聯絡我們
STPA001 - 4 x 50W Class AB Audio Amplifier | STMicroelectronics
STPA001

STPA001 - 4 x 50W Class AB Audio Amplifier | STMicroelectronics

The STMicroelectronics STPA001 is a 4-channel Class AB audio power amplifier built with Multipower BCD technology and MOSFET output stages for high-power car-radio systems. It supports operation down to 6 V, includes a fully complementary P-channel/N-channel output structure for rail-to-rail output swing, and is identified as a quad bridge power amplifier rated up to 50 W per channel under the manufacturer’s stated test conditions. The device is supplied in a 25-Flexiwatt vertical package. A Class AB audio amplifier is a linear power-amplifier category that uses conduction overlap between push-pull output devices to reduce crossover distortion compared with Class B designs. An audio power amplifier converts a low-level audio signal into a current- and voltage-capable drive signal for loudspeakers. STPA001 occupies the power-amplifier IC, audio amplifier, and automotive infotainment electronics hierarchy rather than a small-signal or signal-conditioning amplifier role. Key features include MOSFET output power stages, high output-current capability, low Hi-Fi-class distortion, low output noise, excellent 2 Ω driving capability, standby support, and disturbance immunity. The manufacturer describes operation down to 6 V as suitable for automotive start-stop battery profiles. Its bridge configuration is intended for car-radio speaker loads, where differential speaker drive can increase usable output voltage into the load compared with a single-ended output. The P-channel/N-channel complementary output architecture is significant because it provides rail-to-rail output-voltage swing while reducing saturation losses. That behavior helps maximize the useful output signal available to the speaker and supports the amplifier’s high-power automotive use case. The IC is intended for audio systems where low distortion and controlled output noise are more important than the efficiency of a switching audio stage. Typical applications include automotive head units, car-radio power stages, four-channel speaker systems, audio sub-system amplification, and other vehicle infotainment platforms. The 6 V minimum operating capability makes it relevant to modern vehicle electrical environments, particularly where battery voltage can fall during engine stop or cranking events. The bridge outputs must be paired with the appropriate speaker wiring arrangement shown in the manufacturer’s application information. The main design consideration is power dissipation and heat spreading in the 25-Flexiwatt package. Actual thermal performance depends on supply voltage, speaker impedance, output power, channel loading, PCB copper, and ambient temperature. A replacement must match the package footprint, pinout, bridge-output topology, voltage range, channel count, and thermal conditions; simply matching nominal wattage is not sufficient for a safe drop-in substitution. This page consolidates the verified STPA001 product description, manufacturer datasheet, distributor listing information, and application guidance. It also distinguishes documented facts from parameters that were not supplied, avoiding invented ratings or unsupported replacement claims.

詢價 聯絡我們
STPA001A - 4 x 50W Quad Bridge Audio Amplifier | STMicroelectronics
STPA001A

STPA001A - 4 x 50W Quad Bridge Audio Amplifier | STMicroelectronics

The STMicroelectronics STPA001A is a four-channel Class AB MOSFET bridge power amplifier rated for 4 x 50 W output and supplied from 6 V to 18 V. It is packaged in the vertically formed 27-Flexiwatt power package for high-power car-radio and automotive audio systems. The device uses Multipower BCD technology, a fully complementary P-channel/N-channel MOSFET output stage, standby and mute inputs, clip detection, and offset detection. An audio power amplifier is an integrated circuit that drives loudspeakers rather than only providing a low-power line signal. This STPA001A belongs to the class-AB power-amplifier hierarchy, combining MOSFET output stages with audio signal processing and protection functions. Its bridge topology allows differential speaker drive, while the Class AB biasing supports lower crossover distortion than a typical switching amplifier at the cost of higher standing dissipation. Key verified features include output capability of 50 W per channel into 4 ohms at 14 V and 72 W per channel into 2 ohms at 14 V, low-voltage operation from 6 V to 18 V, excellent two-ohm drive capability, low output noise, and high disturbance immunity. The standby and mute controls support system-level power management, while clip and offset detection support diagnostic or protection functions. The MOSFET output stage is designed for rail-to-rail output swing and high output current. STMicroelectronics describes the device as a class-AB audio power amplifier intended for high-power car radio applications. The datasheet also identifies its 27-Flexiwatt vertical package, which is a thermally relevant power-dissipation package and must be mounted with suitable copper and thermal design. Typical uses include automotive head-unit amplifier stages, car-radio speaker drives, four-channel cabin audio systems, and other bridge-tied audio loads where a low-voltage battery supply is available. The four-channel architecture allows independent regulation of four speaker outputs when configured with the required passive network and load arrangement. Designers should confirm the exact load impedance, supply voltage, thermal pad implementation, output-filter network, and pin-level application circuit in the STMicroelectronics datasheet before layout. Because power dissipation rises with voltage difference and output current, the PCB copper area and thermal path are critical. This page combines verified manufacturer and distributor information with engineering guidance for amplifier selection, thermal implementation, and application planning.

詢價 聯絡我們
STPA001AH - Quad 4x50W Class AB Audio Amplifier | STMicroelectronics
STPA001AH

STPA001AH - Quad 4x50W Class AB Audio Amplifier | STMicroelectronics

The STMicroelectronics STPA001AH is a four-channel Class AB audio power amplifier rated at 4 x 50 W and supplied in a 27-Flexiwatt horizontal power package. Its quad bridge-tied-load configuration is designed for high-power car-radio audio systems. The verified distributor data identifies low-voltage operation, standby and mute inputs, clip detection, offset detection, and MOSFET output technology, but several detailed electrical limits are not available in the supplied sources. A Class AB audio amplifier is an audio amplifier that uses conduction overlap between its output transistors to reduce crossover distortion compared with a pure Class A amplifier. In the broader electronics hierarchy, an audio amplifier belongs to amplifier ICs, analog signal-chain ICs, and semiconductor components. The bridge-tied-load arrangement uses each output stage differentially, allowing speaker current flow in both directions without a conventional DC-blocking output capacitor. Key verified features include four output channels, Class AB operation, up to 50 W per channel as stated by distributor listings, a 27-pin horizontal Flexiwatt package, standby and mute control, clip detection, and offset detection. The standby function can place the amplifier into a low-power state, while mute supports controlled audio attenuation. Clip and offset detection give the surrounding controller useful status signals for protecting the output stage or diagnosing abnormal operation. The STPA001 family uses MOSFET technology for its audio output stage and targets automotive head units, where four speakers or multiple powered speaker channels are common. Compared with an external discrete amplifier made from many transistors and resistors, the integrated quad amplifier reduces board area and assembly effort. Its principal engineering trade-off is substantial heat: actual channel power depends on supply voltage, speaker impedance, distortion limit, thermal conditions, and PCB copper, none of which is fully specified in the supplied data. Typical applications include car-radio head units, automotive infotainment systems, four-speaker cabin audio, powered multimedia enclosures, and low-voltage high-power audio racks when the thermal and supply conditions match the complete manufacturer specification. Each speaker output must connect to a bridge-tied load; grounding either speaker terminal to chassis ground is not an equivalent wiring method. Before layout, obtain the manufacturer datasheet and verify the exact pinout, supply limits, speaker impedance, output-power conditions, thermal resistance, protection limits, exposed-tab connection, and decoupling requirements. Keep the power ground and output-current paths compact, use the prescribed input and bypass capacitors, and thermally couple the horizontal Flexiwatt tab to the PCB copper according to the manufacturer layout guidance. This page consolidates verified distributor descriptions, sourcing information, application context, and design cautions. Parameters not present in the supplied sources remain explicitly marked for verification rather than being inferred from generic Flexiwatt or Class AB amplifier data.

詢價 聯絡我們
STPA001H - 4 x 50W Class AB Audio Amplifier | STMicroelectronics
STPA001H

STPA001H - 4 x 50W Class AB Audio Amplifier | STMicroelectronics

The STMicroelectronics STPA001H is a four-channel Class AB audio power amplifier rated at 4 x 50 W and supplied from 6 V to 18 V. It is packaged in a 25-Flexiwatt horizontal through-hole package with formed leads. The device provides standby and mute inputs, clip detection, and a diagnostics output. According to the manufacturer datasheet, STPA001H is intended for high-power car-radio and automotive audio systems. A power audio amplifier is an integrated analog device that drives loudspeakers from a lower-voltage audio input while delivering the voltage and current required by the load. The STPA001H uses four independent Class AB output channels in a bridge-tied-load arrangement. In this topology, each channel drives the two terminals of a speaker differentially, improving output capability while avoiding a direct ground connection at the load. Key verified features include four 50 W outputs at a 4 Ω load, Class AB operation, 6 V to 18 V supply operation, and 25-Flexiwatt horizontal construction. The standby and mute controls support system-level power management and signal suppression. Clip detection and the diagnostics output provide status information that can be monitored by a vehicle or audio-system controller. The manufacturer describes the STPA001 family as using MOSFET technology for high sound quality and high-power car-radio applications. The device is intended for four-channel audio architectures in which multiple loudspeaker loads must be driven from one integrated power stage. Typical uses include car-radio amplifiers, automotive sound systems, and other bridge-tied-load audio equipment. The 25-Flexiwatt package is a substantial thermal and mechanical solution compared with small surface-mount amplifier packages, making it appropriate for designs where substantial output power and heat-spreading capability are priorities. When designing around STPA001H, preserve the datasheet supply range and account for the power dissipated by the four Class AB output stages. Speaker wiring, grounding, and decoupling should be arranged to minimize hum and switching-related disturbance. The standby and mute pins should be driven according to the manufacturer’s recommended logic levels, while clip and diagnostics signals should be incorporated into system monitoring where useful. This page consolidates verified distributor and manufacturer information with application guidance, comparison fields, and design notes intended to help engineers evaluate STPA001H for high-power automotive audio designs. It does not infer electrical, thermal, or pin-level values that were not present in the supplied source data.

詢價 聯絡我們
STPA002CD-48X - 4x52W Class AB Audio Amplifier | STMicroelectronics
STPA002CD-48X

STPA002CD-48X - 4x52W Class AB Audio Amplifier | STMicroelectronics

STMicroelectronics STPA002CD-48X is a four-channel, MOSFET Class AB audio power amplifier rated for 4 x 52 W maximum output into 4 ohms and 4 x 30 W at 14.4 V, 1 kHz, and 10% distortion, in a 27-Flexiwatt vertical package. It is designed for high-power car-radio and automotive audio systems requiring low-voltage operation, high sound quality, and robust protection against accidental speaker or supply misconnections. An audio power amplifier is an integrated circuit that drives loudspeakers with sufficient voltage, current, and thermal capability to reproduce music and speech. The STPA002 belongs to the Class AB linear audio-amplifier hierarchy, where MOSFET output stages operate in a predominantly linear region for low crossover distortion. Its four-channel architecture can support four speakers or two stereo bridge-tied speaker networks while retaining conventional analog signal paths. Key features include 4 x 52 W maximum output into 4 ohms, 4 x 30 W at 14.4 V under the stated 1 kHz and 10% distortion conditions, standby and mute inputs, clip detection, and offset detection. The verified manufacturer description identifies it as a MOSFET Class AB amplifier designed specifically for high-power car-radio equipment. Low-voltage operation is particularly important in start-stop automotive systems, where the available supply can vary substantially during cranking and engine restart. The device uses four integrated Class AB output stages rather than a switching topology. This avoids the switching-frequency electromagnetic-interference and filter considerations associated with Class D designs, while making amplifier efficiency and heat management more dependent on supply voltage, output power, load impedance, and speaker impedance matching. The producer therefore controls output-stage dissipation through the Flexiwatt package and PCB copper area. Typical applications include automotive head units, car-radio amplifiers, four-speaker cabin systems, and low-voltage mobile audio installations. In a typical bridge-tied circuit, two output channels operate together to drive one speaker, while four channels support four separate speaker loads or two stereo pairs. The mute and standby inputs permit system-level shutdown and ignition-state control without removing the complete audio subsystem from the vehicle. Designers should verify speaker impedance, supply voltage, channel configuration, thermal rise, and protection behavior against the manufacturer datasheet before production. The 27-Flexiwatt vertical package is a power-dissipating surface-mount package and requires adequate PCB copper, clean signal routing, robust supply bypassing, and careful output-pad layout. Speaker outputs must also remain isolated from chassis ground unless the selected bridge-tied configuration and system grounding plan require otherwise. This product data combines the verified STMicroelectronics product description with distributor availability, package identification, and technical comparison data. It also identifies the limited drop-in replacement evidence found in the supplied cross-reference results, allowing engineers to distinguish a documented same-package candidate from unsupported guesses.

詢價 聯絡我們
STPA002HSD-48X - Quad Class AB Audio Power Amplifier | STMicroelectronics
STPA002HSD-48X

STPA002HSD-48X - Quad Class AB Audio Power Amplifier | STMicroelectronics

The STMicroelectronics STPA002HSD-48X is a four-channel Class AB audio power amplifier designed for automotive infotainment and high-power car-radio systems. It is offered in the 27-Flexiwatt vertical package and combines multiple audio output channels with robust protection against several fortuitous misconnections. The device is intended for low-voltage vehicle operation, including start-stop automotive systems that place additional demands on audio amplifiers during transient battery conditions. An audio power amplifier is an integrated circuit that converts low-level audio signals into current and voltage capable of driving loudspeakers. A Class AB amplifier conducts for both halves of the signal cycle, balancing linearity and efficiency compared with more highly efficient but nonlinear switching classes. The STPA002 belongs to the broader hierarchy of amplifier IC, linear audio amplifier, audio power amplifier, and automotive power-semiconductor product categories. The STPA002 is designed as a MOSFET Class AB audio power amplifier. Its four-channel configuration supports multi-speaker vehicle audio systems where front and rear speaker groups may require independent amplification. STMicroelectronics highlights the device’s outstanding output-current capability, distortion performance, and robustness against fortuitous misconnections. The manufacturer also states that the amplifier complies with current OEM requirements for low-voltage operation in start-stop vehicles. Automotive audio differs from conventional consumer audio because the battery voltage can vary during engine cranking, and alternator behavior can produce large electrical transients. The STPA002HSD-48X is therefore positioned as a robust bridge-oriented power stage for vehicle radio systems. Its MOSFET output architecture is intended to combine efficient loudspeaker drive with the low distortion expected from a Class AB audio amplifier. Typical uses include car head units, automotive radio systems, four-speaker infotainment platforms, and vehicle audio subassemblies with multiple amplified outputs. The four-channel architecture simplifies allocation of amplifier channels across the vehicle cabin. In a typical design, the source unit supplies audio signals, protection and filtering networks handle board-level concerns, and the amplifier drives speaker loads through suitable output networks. Designers should evaluate the exact output power, channel configuration, load impedance, thermal limits, supply range, distortion behavior, and pin functions from the manufacturer datasheet before finalizing the PCB. The vertical 27-Flexiwatt package also requires attention to copper area and thermal paths because an audio power amplifier dissipates energy as heat. Proper grounding, speaker-routing isolation, and protection against accidental short circuits are essential in a vehicle environment. This product page combines the manufacturer’s device positioning with distributor package and catalog information, then adds engineering-focused selection, thermal, layout, and comparison guidance. It is intended to help designers distinguish the STPA002HSD-48X from unrelated quad audio amplifiers before validating the final schematic, footprint, and operating limits.

詢價 聯絡我們
STPA002OD-4WX - 4x52W Quad Class AB Audio Amplifier | STMicroelectronics
STPA002OD-4WX

STPA002OD-4WX - 4x52W Quad Class AB Audio Amplifier | STMicroelectronics

The STMicroelectronics STPA002OD-4WX is a four-channel Class AB audio power amplifier rated for 4 x 52 W operation in a 25-Flexiwatt vertical package. Designed primarily for high-power car-radio and automotive audio systems, it combines four amplifier outputs with standby and mute inputs compatible with 3.3 V and 5 V control signals. The package is identified by distributors as Flexiwatt25, package code FM2 or ZFM, with 25 terminals. A Class AB audio amplifier is a transistor-based power amplifier that conducts through both halves of its signal cycle. Relative to switching amplifiers, this architecture can provide a simpler signal path and controlled output-stage behavior, while the STPA002OD-4WX is specifically engineered to deliver high output current, manage distortion, and withstand automotive supply conditions. It belongs to the broader hierarchy of audio amplifiers, linear amplifiers, analog power amplifiers, and integrated circuits. The manufacturer describes the STPA002 as a MOSFET Class AB audio power amplifier for high-power car radio. Its four-channel bridge configuration supports four x 52 W output capability, while standby and mute pins accept 3.3 V and 5 V logic. The device is designed for the low-voltage operating requirements of modern start-stop vehicles and can sustain hybrid-vehicle battery transitions. Its output stage is also reported as robust against several common fortuitous speaker misconnections. Acoustic performance depends on correct analog implementation as well as the amplifier IC itself. The manufacturer datasheet recommends input capacitors having the same capacitance as the capacitor connected to the AC-GND pin for optimum pop performance. This matching requirement is important because startup and shutdown transients can propagate through the input network. Speaker load selection, power-supply stability, heat sinking, and the Flexiwatt25 thermal pad connection also determine whether the amplifier can sustain its rated output in a compact automotive enclosure. Typical uses include automotive head-unit power stages, low-voltage car-radio systems, four-channel bridge-tied speaker drives, and aftermarket or OEM audio modules designed around start-stop battery systems. The four-output architecture simplifies board-level channel allocation compared with separate amplifier packages, provided the design includes adequate supply filtering, protection, and thermal management. A key implementation trade-off is thermal capability. The 25-Flexiwatt package is intended to dissipate substantial heat, but the PCB must provide the manufacturer-recommended copper and thermal interface. Users should also verify speaker impedance, load configuration, supply limits, and automotive transient requirements against the current datasheet before production release, since those operating details are not included in the distributor snippets reviewed. This product data combines the verified STMicroelectronics product description, distributor classification, package details, low-voltage control information, and pop-performance guidance with practical application and design guidance. It also distinguishes documented capabilities from parameters that still require confirmation from the manufacturer datasheet.

詢價 聯絡我們
STPA003CD-48X - 4x52W Class AB Audio Amplifier | STMicroelectronics
STPA003CD-48X

STPA003CD-48X - 4x52W Class AB Audio Amplifier | STMicroelectronics

The STMicroelectronics STPA003CD-48X is a four-channel, Class AB MOSFET audio power amplifier rated at 4 x 52 W, with output power described as 85 W per channel into a 2 ohm load. It is designed for high-power automotive radio and other low-voltage audio systems and is available in a vertical 27-Flexiwatt through-hole package. The device also includes low-voltage operation, clip detection, offset detection, and strong GSM noise immunity. An automotive audio power amplifier is an integrated circuit that accepts low-level audio inputs and drives loudspeakers through power MOSFET output stages. The STPA003 belongs to the MOSFET Class AB amplifier family, a subtype of audio amplifier and analog power-management IC. Class AB operation combines low crossover distortion with useful power efficiency, making it suitable for continuous loudspeaker drive where fidelity and thermal robustness matter more than the efficiency of a switching amplifier. Key features include four independent amplifier channels, a 4 x 52 W headline output rating, 85 W per channel capability into 2 ohms, and a 27-Flexiwatt vertical package. The low-voltage operating design supports start-stop automotive battery profiles. Clip and offset detection provide system-level diagnostic functions, while the reported GSM noise immunity helps preserve audio quality in electrically noisy vehicle environments. The MOSFET output architecture is intended to combine high output-current capability with low distortion. Published distributor data identifies a nominal output power of 55 W and harmonic distortion of 0.01%, while the manufacturer describes the STPA003 family as designed for high-power car radio applications. Exact test conditions, protection thresholds, channel-to-channel gain matching, and detailed thermal data require review of the manufacturer datasheet before a production design is released. Typical applications include automotive head units, high-power car-radio channels, four-speaker cabin systems, low-voltage multimedia systems, and auxiliary automotive audio racks. In a bridge-tied-load implementation, the amplifier can drive four loudspeaker channels while reducing the number of external output networks normally associated with single-ended amplifier stages. A critical design consideration is the thermal path from the 27-Flexiwatt package to the printed circuit board. Copper area, through-hole thermal dissipation, enclosure airflow, ambient temperature, and the sustained loudspeaker load determine whether the amplifier operates within its intended limits. Input and output network design must also preserve low distortion across the complete audio bandwidth. This product record consolidates the verified manufacturer and distributor information into an engineering-focused reference covering package characteristics, application suitability, verified drop-in candidates, and practical selection considerations that are not presented as a substitute for the complete STMicroelectronics datasheet.

詢價 聯絡我們
STPA003HSD-48X - 4x52W Class AB Audio Amplifier
STPA003HSD-48X

STPA003HSD-48X - 4x52W Class AB Audio Amplifier

STMicroelectronics STPA003HSD-48X is a four-channel, MOSFET class AB bridge-tied-load audio power amplifier rated for 4 x 52 W output in the 27-Flexiwatt vertical package. The device is designed for high-power car-radio and automotive audio systems operating from a low-voltage battery supply. Its four-channel configuration supports four BTL speaker outputs, while integrated clip detection and offset detection provide fault information for system monitoring. A bridge-tied-load audio amplifier is a power-management semiconductor that drives a speaker differentially. Unlike a single-ended amplifier, a BTL output applies the audio waveform across the two speaker terminals, increasing usable output voltage into the load. The STPA003 combines this output topology with MOSFET output devices, class AB conduction, and a high-side driver. These characteristics place it within the hierarchy of audio amplifier IC, power amplifier, analog power IC, and semiconductor. The primary headline specifications are 4 x 52 W output power, four-channel class AB operation, and the 27-Flexiwatt vertical package. The verified manufacturer description also identifies low-voltage operation, high sound quality, excellent GSM noise immunity, clip detection, and offset detection as central device features. The quad-channel arrangement can reduce the number of amplifier packages needed in a multichannel automotive head unit or radio while retaining individual-channel fault monitoring. The STPA003 is specifically intended for high-power car-radio applications. Its low-voltage operation is relevant to automotive systems where supply conditions can vary, while the specified GSM noise immunity helps preserve audio quality in electrically noisy environments. Clip detection can identify output overdrive conditions, and offset detection can flag undesirable output bias. These monitoring functions support safer system integration when paired with suitable diagnostic circuitry. Typical applications include automotive head units, car-radio systems, multi-zone cabin audio, powered speaker arrangements, and low-voltage audio infrastructure. The four-channel BTL architecture is particularly useful where four speakers or stereo front and rear channels must be driven from one power-amplifier package. Installation still requires correct speaker impedance, supply decoupling, thermal planning, output filtering, and protection against wiring faults. The primary design consideration is to follow the manufacturer datasheet for pin assignment, exposed-pad or thermal-pad connection, output filtering, input network, and application limits. Automotive battery power also requires transient and reverse-polarity protection outside the IC when required by the system specification. PCB copper area and thermal vias directly affect heat dissipation from the 27-Flexiwatt power package. This page consolidates verified manufacturer and distributor information for engineering selection, including output topology, channel count, package identity, fault features, pricing context, and design considerations. It also separates explicitly documented characteristics from parameters that still require confirmation from the complete manufacturer datasheet or application-specific data.

詢價 聯絡我們
STPA008-48X - 4x50W Class AB Audio Amplifier | ST
STPA008-48X

STPA008-48X - 4x50W Class AB Audio Amplifier | ST

STMicroelectronics STPA008-48X is a four-channel, Class AB audio power amplifier delivering 4 x 50 W into a 27-Flexiwatt vertical package. Designed primarily for high-power car-radio systems, the device combines four independent MOSFET output amplifiers with standby, mute, offset detection, clipping detection, and diagnostic functions. According to the manufacturer datasheet, it can operate from a 6 V battery supply, supporting low-voltage and start-stop automotive operating profiles while preserving useful output swing and sound quality. An audio power amplifier converts low-level audio signals into a current and voltage capable of driving loudspeakers. The STPA008 belongs to the Class AB amplifier hierarchy, where output devices conduct continuously to reduce crossover distortion compared with Class D designs. It also sits within the broader automotive audio power-amplifier category. Its four independent channels make it suitable for conventional four-speaker systems using bridge-tied-load outputs, while its diagnostic features help system designers identify faults in complex vehicle audio installations. Key characteristics include a fully complementary P-channel and N-channel MOSFET output stage, rail-to-rail output-voltage swing, high output current, minimized saturation losses, low-voltage operation down to 6 V, standby and mute control, offset detection, clipping detection, and a diagnostics output. The manufacturer describes the architecture as providing high sound quality and excellent GSM-noise immunity, which are useful attributes in automotive environments where radio-frequency interference can otherwise affect audio playback. The STPA008-48X targets high-power car-radio and automotive infotainment applications rather than portable headphone outputs or very small consumer speakers. Four independent Class AB channels allow a compact solution for multi-speaker vehicle systems without requiring four separate monolithic amplifier packages. The vertical 27-Flexiwatt package is intended for PCB mounting and careful thermal design; class-AB dissipation and automotive ambient conditions must be considered when sizing copper areas and heat spreading. Engineers should follow the manufacturer’s reference layout and pin-connection requirements, preserve the intended bridge-tied-load topology, and decouple supply rails close to the device. The offset detector, clipping detector, standby pin, mute pin, and diagnostics output must be connected according to the datasheet. The 6 V minimum supply supports start-stop systems, but headroom above 6 V is generally necessary to achieve the specified 4 x 50 W output without entering clipping or thermal limits. This product summary combines the verified STMicroelectronics product information with distributor availability, package details, application guidance, and the only identified cross-brand comparison candidate. It distinguishes confirmed device attributes from package drawings and electrical values that could not be independently verified from the supplied search results.

詢價 聯絡我們
STPA008-4WX - 4x50W Class AB Audio Amplifier | STMicroelectronics
STPA008-4WX

STPA008-4WX - 4x50W Class AB Audio Amplifier | STMicroelectronics

STMicroelectronics STPA008-4WX is a four-channel, 50 W-per-channel Class AB BTL audio power amplifier built with MOSFET output stages and supplied in a 25-Flexiwatt vertical package. It operates from a minimum supply voltage of 6 V and integrates four independent amplifier channels for automotive audio systems. The 6 V operating capability supports low-voltage and start-stop battery operating profiles, while the MOSFET architecture targets high sound quality and automotive EMI robustness. An automotive audio power amplifier is a multi-channel integrated circuit that accepts low-level audio inputs and drives loudspeaker loads through differential, bridge-tied-load outputs. In the product hierarchy, the STPA008-4WX is an audio amplifier IC, a class AB amplifier, a BTL output stage, a MOSFET power amplifier, and an automotive power-management and signal-conditioning device. Its four-channel architecture reduces the number of separate output amplifiers required in a car-radio or infotainment system. The principal device ratings are 4 x 50 W output power, a 6 V minimum operating supply, four independent Class AB channels, and a 25-Flexiwatt vertical package. Additional verified functions include standby and mute controls, an offset detector, and 3.3 V CMOS-compatible standby and mute pins. The Flexiwatt27 version adds clipping detection and a diagnostics output, but those functions are not listed for the Flexiwatt25 STPA008-4WX version. Each channel uses a bridge-tied-load topology, allowing the amplifier to drive a loudspeaker differentially and deliver the stated 50 W output capability without a single-ended output connection. The manufacturer describes the device as a complementary quad audio amplifier with MOSFET output devices. The offset detector can support system monitoring, while the mute and standby inputs permit the host head unit to control audible output and low-power states independently of the audio source. Typical applications include automotive head units, car-radio systems, automotive infotainment amplifiers, low-voltage start-stop audio systems, and multi-channel vehicle loudspeaker drives. Operation down to 6 V is particularly relevant where the battery can fall below a conventional 12 V nominal level during engine stop. The four-channel quad structure allows left and right front speakers and left and right rear speakers to be driven from one power-amplifier package. Power-supply layout, speaker return paths, and input filtering are critical in this application. The manufacturer application circuit specifies input capacitors equal to one quarter of the capacitor connected to the AC-GND pin for optimum pop performance. RC networks must be placed on both mute and standby pins to smooth transitions and suppress audible transients, and the amplifier requires careful thermal design because it can dissipate substantial power in a compact package. This product record combines manufacturer and distributor information with application-specific design guidance, verified pricing references, comparison parameters, and drop-in candidate analysis. It distinguishes the STPA008-4WX from the Flexiwatt27 version and identifies where additional technical data or a verified pin-to-pin cross-reference is still required before a substitution is approved.

詢價 聯絡我們
STPA008-QIX - 4x50W Class AB Audio Amplifier | STMicro
STPA008-QIX

STPA008-QIX - 4x50W Class AB Audio Amplifier | STMicro

The STMicroelectronics STPA008-QIX is a 4-channel, 4 x 50 W MOSFET quad-bridge Class AB audio power amplifier packaged in 25-Flexiwatt (Horizontal). It combines four independent output amplifiers with standby and mute control, making it suitable for high-power automotive audio systems, including car-radio head units. The device operates down to a 6 V battery voltage, supporting start-stop vehicle battery profiles in which the supply can fall below conventional automotive operating voltages. An audio power amplifier is an integrated circuit that converts low-level audio signals into high-current outputs capable of driving loudspeakers. The STPA008 belongs to the Class AB power-amplifier hierarchy, where the output transistors conduct for more than half of each signal cycle. Compared with a switching amplifier, this topology supports a conventional analog signal path and is specifically identified for high-power car-radio applications. Its MOSFET-based complementary output stage provides four amplification channels in one package. Key verified features include four independent 50 W output stages, Class AB operation, a 6 V minimum operating supply, standby and mute functions, and an offset detector. The manufacturer describes the device as a low-voltage, high-sound-quality bridge-tied-load amplifier with improved GSM noise immunity. The Flexiwatt25 horizontal package is the -QIX ordering form identified by DigiKey, while the manufacturer datasheet also documents a distinct Flexiwatt27 option with clipping detection and a diagnostics output. Technically, the quad-bridge architecture is intended to increase usable speaker output power and reduce the number of separate amplifier packages required in a multichannel head unit. The offset detector helps identify undesirable amplifier-channel DC offset. Features such as clipping detection and diagnostics output belong to the Flexiwatt27 configuration according to the manufacturer overview and should not be assumed to be present in the Flexiwatt25 -QIX device without checking the package-specific pinout. Typical applications include automotive head units, car-radio systems, four-channel speaker arrangements, and low-voltage vehicle audio platforms. The 6 V operating capability is particularly relevant to start-stop vehicles, where engine shutdown can transiently reduce the battery voltage while audio equipment remains connected. System designers must still verify speaker impedance, thermal dissipation, supply layout, and automotive qualification requirements for the complete end product. The most important design consideration is thermal management because a 4 x 50 W device can dissipate substantial power in a multi-channel bridge configuration. The 25-Flexiwatt package requires a correctly implemented PCB heat-spreading structure, and each channel must remain within its allowed output conditions. Input, output, supply, and return paths should be laid out to minimize coupling between four high-current output stages and sensitive audio inputs. This product data consolidates the verified manufacturer overview, distributor identification, package information, and application details into an engineering-focused resource. It also distinguishes confirmed STPA008 capabilities from package-specific functions that require datasheet verification and explicitly identifies the absence of verified numeric pricing and drop-in substitute data.

詢價 聯絡我們