產品(44,000+)

STM32L031K6T6 - Ultra-Low-Power ARM Cortex-M0+ MCU | STMicroelectronics
STM32L031K6T6

STM32L031K6T6 - Ultra-Low-Power ARM Cortex-M0+ MCU | STMicroelectronics

The STMicroelectronics STM32L031K6T6 is an ultra-low-power 32-bit microcontroller based on the ARM Cortex-M0+ core, operating at up to 32 MHz. It features 32 KB of Flash memory and 8 KB of SRAM, packaged in a 32-pin LQFP (TQFP32) with a 7x7 mm footprint. This device is part of the STM32L0 series, designed for battery-powered and energy-efficient applications. What is an ultra-low-power microcontroller? An ultra-low-power microcontroller is a system-on-chip that integrates a processor core, memory, and peripherals while minimizing energy consumption, often featuring multiple low-power modes such as sleep, stop, and standby. These devices are essential in the hierarchy of embedded systems, from simple 8-bit MCUs to complex application processors, where power efficiency is critical for extending battery life in portable and IoT devices. Key features include a 12-bit ADC with hardware oversampling, multiple communication interfaces (I2C, SPI, USART), and a rich set of timers including a low-power timer. The device supports a wide supply voltage range from 1.8V to 3.6V, with a typical operating current of 84 uA/MHz in Run mode and as low as 0.29 uA in Standby mode with RTC. The STM32L031K6T6 also integrates a true EEPROM emulation, a 12-bit DAC, and a comparator, making it versatile for analog sensing applications. Technically, the STM32L031K6T6 is built on a 110nm process, offering a balance between performance and power. The Cortex-M0+ core includes a single-cycle multiplier and a nested vectored interrupt controller (NVIC), enabling efficient interrupt handling. The device features a flexible clocking system with an internal 16 MHz RC oscillator, an external crystal oscillator, and a PLL, allowing designers to optimize for speed or power. Typical applications include portable medical devices, smart sensors, fitness trackers, and industrial monitoring systems. Its ultra-low-power modes and rich analog peripherals make it ideal for applications that require long battery life and precise analog measurements, such as wearable health monitors and environmental sensors. When designing with this device, pay attention to the power supply decoupling: place a 100nF capacitor close to each VDD pin and a 1uF capacitor on the main supply. For lowest power consumption, use the STOP mode with the RTC running, and configure unused GPIOs as analog inputs to avoid leakage currents.

詢價 聯絡我們
STM32L031K6T7 - 32MHz Cortex-M0+ 32KB MCU | STMicroelectronics
STM32L031K6T7

STM32L031K6T7 - 32MHz Cortex-M0+ 32KB MCU | STMicroelectronics

The STMicroelectronics STM32L031K6T7 is an ultra-low-power 32-bit microcontroller built around the Arm Cortex-M0+ core, operating at up to 32 MHz with 32 KB of Flash memory in a 32-LQFP 7 x 7 mm package. It is designed for compact embedded systems that require efficient control processing, low power consumption, and a broad operating-temperature range. An ultra-low-power microcontroller is a semiconductor device designed to minimize energy use during active operation, sleep, and standby modes. The STM32L031K6 belongs to STMicroelectronics' access-line STM32L0 family. Its position in the hierarchy is microcontroller IC, embedded processor, microcontroller, and semiconductor. This makes it suitable for compact battery-powered sensing, industrial control, communications, and consumer equipment where a general-purpose processor would be unnecessarily large or power-hungry. Key features include a 32 MHz Arm Cortex-M0+ processor, 32 KB of Flash program memory, and 8 KB of SRAM. The verified product information also identifies a 12-bit ADC and an operating-temperature range of -40°C to +105°C. These specifications support firmware storage, real-time control tasks, analog signal acquisition, and industrial thermal requirements while keeping the device within the STM32L0 access-line portfolio. The 32-bit Cortex-M0+ architecture provides a compact instruction set and efficient execution for embedded workloads. With 32 KB of Flash, the MCU can hold boot code, application firmware, configuration data, and protocol handlers without requiring an external memory interface. Its 8 KB of SRAM provides working memory for control loops, communication buffers, and peripheral data handling, although developers should size memory carefully in highly concurrent applications. Typical applications include low-power sensor nodes, industrial monitoring equipment, compact control panels, building automation endpoints, battery-operated instruments, and embedded communications controllers. The -40°C to +105°C range makes the device relevant to demanding industrial environments, while the 12-bit ADC supports analog inputs used in sensing and measurement designs. When designing around the STM32L031K6T7, verify every peripheral, alternate-function mapping, pin requirement, and software-driver dependency against the manufacturer documentation. Pay particular attention to startup configuration, clock limits, ADC acquisition requirements, and low-power mode transitions. PCB layout should preserve clean power distribution and appropriate decoupling around this 32-LQFP device. This product page consolidates verified manufacturer and distributor information, purchase context, technical comparison data, and practical design guidance. It distinguishes verified attributes from specifications requiring confirmation, helping engineers evaluate the STM32L031K6T7 without relying on generic microcontroller claims.

詢價 聯絡我們
STM32L031K6U6 - 32MHz Cortex-M0+ 32KB MCU | STMicroelectronics
STM32L031K6U6

STM32L031K6U6 - 32MHz Cortex-M0+ 32KB MCU | STMicroelectronics

STMicroelectronics STM32L031K6U6 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller operating at 32 MHz, with 32 KB flash memory, in a 32-pin UFQFPN 5x5 mm package. It belongs to the STM32L0 access-line family and targets compact, energy-conscious embedded systems. The verified distributor listing identifies the device as a 32-bit, 32 MHz MCU with 32 KB flash and a 32-UFQFPN package. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and communication interfaces into one embedded-control platform. The STM32L031K6U6 combines an Arm Cortex-M0+ RISC core with low-power design goals, allowing firmware to control sensors, communications, timers, and analog or digital peripherals in compact products. The principal verified characteristics are a 32 MHz operating frequency, 32-bit architecture, 32 KB flash memory, and a compact 32-pin UFQFPN package. The Arm Cortex-M0+ core provides a straightforward instruction set for embedded applications, while the STM32L0 family positioning emphasizes low power consumption for battery-operated and resource-constrained equipment. The STM32L031K6 family is associated with the STMicroelectronics STM32L0 ultra-low-power portfolio. Typical embedded uses include low-power sensor nodes, compact control boards, portable instruments, simple communication equipment, and IoT devices where the combination of processing capability, memory, and package size is useful. Exact peripheral availability, electrical limits, memory-map details, and timing parameters should be confirmed in the manufacturer datasheet before final design release. Designers should preserve the package footprint, pin assignment, supported voltage range, decoupling requirements, clock configuration, and programming interface when creating a PCB. Because the supplied data does not include a full electrical table or complete pinout, unsupported values are marked as needed rather than inferred. This page combines verified distributor identification, manufacturer product information, practical application guidance, and sourcing context. This product summary distinguishes the STM32L031K6U6 from functionally related STM32 devices by emphasizing the verified combination of Cortex-M0+ architecture, 32 MHz operation, 32 KB flash, and 32-pin UFQFPN packaging. It is a useful starting point for embedded engineers evaluating low-power MCU designs and comparing package-compatible sourcing options.

詢價 聯絡我們
STM32L041F6P7 - 32MHz Cortex-M0+ 32KB Flash MCU with AES | STMicroelectronics
STM32L041F6P7

STM32L041F6P7 - 32MHz Cortex-M0+ 32KB Flash MCU with AES | STMicroelectronics

The STMicroelectronics STM32L041F6P7 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller with 32 KB of Flash memory, 8 KB of SRAM, a 32 MHz CPU and a hardware AES accelerator, packaged in a 20-pin TSSOP (0.173 inch / 4.40 mm body width) surface-mount package. The STM32L041F6 access-line family targets cost-sensitive, battery-operated embedded designs where low active and standby current matter more than raw processing throughput. A microcontroller (MCU) is a self-contained embedded processing unit: a CPU core, program Flash, data SRAM, and a set of on-chip peripherals such as timers, serial interfaces, ADCs and GPIO, all integrated on a single die. The STM32L041F6 belongs to the STM32L0 access line, the entry tier of the STM32 family, and its Arm Cortex-M0+ core is the smallest and most energy-efficient member of the Cortex-M architecture, sitting at the bottom of the hierarchy MCU > microcontroller > embedded processor > semiconductor. Key features include the 32 MHz Cortex-M0+ core with its single-cycle multiplier and divider, 32 KB of Flash (32K x 8) alongside 8 KB of SRAM, an on-chip hardware AES accelerator for encrypted data links, and a small 20-TSSOP outline that keeps boards compact. The part is listed as Active in the lifecycle, is ROHS3 compliant, ships in a tray package, and carries a stated lead time of 17 weeks as of the October 2026 distributor data. Technologically, the STM32L041F6 is built around the ultra-low-power Arm Cortex-M0+ core with a 32 MHz maximum clock and a simple, deterministic peripheral set oriented around low-power operation. The 32 KB of Flash holds the application code and the 8 KB of SRAM serves as the working data space, which is adequate for small control loops, sensor fusion and low-rate communications. The AES block offloads encryption from the CPU, freeing the core for acquisition and protocol handling in secure metering and connected-sensor designs. Typical applications include low-cost IoT sensor nodes, smart water and gas meters, battery-powered wearables and trackers, industrial monitoring modules, compact keypads, and small motor or relay control boards where the 20-pin footprint and low standby current are decisive. When designing around this device, keep the decoupling network tight: place a 100 nF ceramic capacitor at each VDD pin and a 4.7 uF bulk capacitor close to the supply pins, and verify that your PCB footprint matches the 0.65 mm pitch 20-pin TSSOP. Because only 20 pins are available, budget carefully for analog inputs and serial lines, and confirm that the peripheral mix of your chosen variant matches your design. This page consolidates distributor pricing, lifecycle status and lead time as of 2026-10-28, a parameter-by-parameter comparison against pin-compatible STM32L0 alternatives, and practical design notes that are not found on the distributor product pages themselves.

詢價 聯絡我們
STM32L051C6T6 - 32MHz Cortex-M0+ 32KB MCU | STMicroelectronics
STM32L051C6T6

STM32L051C6T6 - 32MHz Cortex-M0+ 32KB MCU | STMicroelectronics

The STMicroelectronics STM32L051C6T6 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller rated at 32 MHz, with 32 KB of Flash memory and 8 KB of RAM, housed in a 48-pin LQFP package. It belongs to STMicroelectronics’ STM32L0 access-line family and combines a compact general-purpose controller with energy-saving modes for embedded designs. A microcontroller is a programmable semiconductor system that integrates a CPU core, memory, I/O, and peripherals on one device. In the STM32 hierarchy, this MCU belongs to the STM32 family, the STM32L0 series, and the Arm Cortex-M0+ embedded-processing class. That architecture supports compact control firmware while separating larger tasks from low-power sensing or monitoring functions. The verified product information identifies a 32-bit Arm Cortex-M0+ core, 32 MHz operating frequency, 32 KB Flash, and an LQFP package measuring 7 mm by 7 mm. Distributor records also identify this orderable variant as a 48-pin tray-packaged device. The STM32L051x6/8 family description additionally lists embedded memory protection, enhanced I/O, and low-power capabilities, although individual peripheral values are not present in the supplied verification data. Ultra-low-power MCU architecture is particularly useful where average energy consumption matters more than maximum processing throughput. A device such as the STM32L051C6T6 can serve as the central controller for a battery-powered sensor node, industrial monitoring module, or connected actuator controller. Its 32 MHz Cortex-M0+ core provides a straightforward Arm software target, while 32 KB Flash constrains firmware and boot-code capacity compared with higher-memory STM32 devices. Potential uses include compact environmental sensors, low-power condition-monitoring nodes, appliance controls, meter interfaces, actuator controls, and embedded accessories that periodically wake a controller to acquire or process data. The 48-LQFP package also exposes more I/O than small dual in-line packages, but it requires a larger PCB footprint and careful assembly planning. Design planning should begin with the manufacturer’s pinout, memory map, and electrical limits. Do not infer unavailable GPIO, timer, analog, communication, voltage, current, or temperature specifications from family-level descriptions. Confirm that 32 KB of Flash is sufficient for the final bootloader and application, and review the exact peripheral mapping for each 48-pin board design. This product page combines verified manufacturer specifications, distributor availability, sourcing details, and application guidance. It also distinguishes exact drop-in alternatives from broader functional substitutes, helping engineers make PCB-level decisions without treating different Cortex-M devices as interchangeable.

詢價 聯絡我們
STM32L051C8T3 - 32MHz Cortex-M0+ 64KB Flash MCU | STMicroelectronics
STM32L051C8T3

STM32L051C8T3 - 32MHz Cortex-M0+ 64KB Flash MCU | STMicroelectronics

The STMicroelectronics STM32L051C8T3 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller in the STM32L0 access line, delivering 32 MHz CPU performance with 64 KB of Flash and 8 KB of SRAM in a 48-pin LQFP (7x7 mm) package. Operating from a 1.65 V to 3.6 V supply, it targets battery-powered and energy-harvesting designs where every microamp matters. An ultra-low-power microcontroller (MCU) is a class of embedded processor that combines a CPU core, on-chip memory, and a rich peripheral set with deep-sleep modes drawing only nanoamps to microwatts of quiescent current. The STM32L0 family sits inside the broader hierarchy of Cortex-M microcontrollers -> 32-bit MCUs -> microcontrollers -> microprocessors -> semiconductors, and ST positions the STM32L0 access line as the entry point for ultra-low-power embedded designs. Key features include 64 KB single-bank Flash, 8 KB SRAM, an 8-channel 12-bit ADC reaching 1 Msps, two ultra-low-power comparators, a real-time clock (RTC) with calendar, multiple timers (16-bit, 32-bit, SysTick), and seven communication interfaces including USART, SPI, and I2C. The integrated LDO + step-down DC-DC regulator combination on selected SKUs minimizes active and standby current while supporting flexible power modes. Architecturally, the Cortex-M0+ core pairs with ST's proprietary ultra-low-power peripherals (ULP) including low-power timers, brown-out reset, and multiple low-power run/sleep/shutdown modes. The dual-voltage operation and integrated DC-DC converter (on related STM32L0x2/x3 variants) deliver MCU run currents typically below 100 uA/MHz and standby currents in the sub-microamp range. Typical applications include IoT sensor nodes, wearable health monitors, smart meters, wireless remote controls, energy-harvesting devices, and battery-backed industrial alarms. Designers choose the STM32L051C8T3 specifically when they need deterministic Cortex-M0+ simplicity, generous Flash for an OTA-capable stack, and LQFP-48 hand-solderable packaging for prototyping or low-volume builds. When designing with this device, decouple both VDD and VDDA rails with 100 nF + 1 uF ceramics placed within 5 mm of the pins, and route the NRST line away from switching traces. The package's 7x7 mm LQFP-48 footprint is the industry-standard 0.5 mm pitch land pattern, simplifying PCB reuse across the STM32L0 family. This page synthesizes distributor pricing, drop-in alternatives within the STM32L0 family, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
STM32L051C8T6 - Ultra-Low-Power ARM Cortex-M0+ MCU | STMicroelectronics
STM32L051C8T6

STM32L051C8T6 - Ultra-Low-Power ARM Cortex-M0+ MCU | STMicroelectronics

The STM32L051C8T6 is an ultra-low-power 32-bit microcontroller from STMicroelectronics, based on the ARM Cortex-M0+ core running at up to 32 MHz. It integrates 64 KB of Flash memory and 8 KB of SRAM, with a rich set of peripherals including a 12-bit ADC, comparators, timers, and multiple communication interfaces (I2C, SPI, USART). The device operates from a 1.8V to 3.6V supply and features several low-power modes, making it ideal for battery-powered and energy-harvesting applications. Data verified as of 2026-08-05. What is an ultra-low-power microcontroller? An ultra-low-power microcontroller is a type of embedded processor designed to minimize energy consumption while maintaining computational capability. It fits within the broader hierarchy: ARM Cortex-M0+ core -> 32-bit microcontroller -> embedded processor -> semiconductor. These devices are optimized for applications where battery life is critical, such as IoT sensors, wearables, and portable medical devices. The STM32L0 series specifically targets the low-power segment with multiple sleep modes and dynamic voltage scaling. Key features include a 12-bit ADC with hardware oversampling, a low-power UART, and a real-time clock (RTC) with calendar. The device supports a wide operating temperature range of -40°C to +85°C and is available in a 48-pin LQFP package. The STM32L051C8T6 also includes a unique device ID, CRC calculation unit, and a true random number generator (RNG) for security applications. Technically, the STM32L051C8T6 is built on ST's ultra-low-power technology, featuring a flexible clock tree with multiple internal/external oscillators. It supports a 1.8V to 3.6V power supply and has a typical current consumption of 3.4 µA in Stop mode with RTC, and 0.29 µA in Standby mode. The device also includes a brown-out reset (BOR) and power-on reset (POR) for reliable operation. Typical applications include IoT sensor nodes, smart home devices, portable medical monitors, and industrial sensor interfaces. Its low power consumption and rich analog peripherals make it suitable for battery-powered designs where long operational life is required. When designing with this MCU, pay attention to the power supply decoupling and the selection of the appropriate low-power mode for your application. Use the STM32CubeMX tool to configure the clock tree and peripherals efficiently. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the ST datasheet, providing a comprehensive resource for engineers evaluating the STM32L051C8T6.

USD $0.98 聯絡我們
STM32L051C8T7 - 32MHz 64KB Cortex-M0+ MCU | STMicroelectronics
STM32L051C8T7

STM32L051C8T7 - 32MHz 64KB Cortex-M0+ MCU | STMicroelectronics

The STMicroelectronics STM32L051C8T7 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller operating at 32MHz, with 64KB of Flash memory and a 48-pin LQFP package measuring 7 x 7 mm. It belongs to the STM32 L0 access-line family, combining a compact RISC core with low-power operation for compact embedded systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The STM32L0 series is positioned within the hierarchy of embedded microcontroller ICs and specifically targets low-power designs. This makes the STM32L051C8T7 suitable for systems that need responsive control and broad peripheral integration while operating from constrained energy budgets. Key characteristics include a 32MHz Arm Cortex-M0+ RISC core, 64KB of Flash, and 12-bit ADC support with an operating temperature range of -40°C to +105°C. The 48-LQFP package provides a conventional leaded surface-mount footprint suitable for designs assembled with standard PCB equipment. Its 32-bit architecture and peripheral integration allow one device to handle control logic, sensor acquisition, communications, and system supervision. The STM32L0 architecture is designed around an Arm Cortex-M0+ core, a compact instruction set intended for embedded control rather than high-performance computing. The 64KB Flash area provides room for application firmware, while integrated peripherals reduce the need for external components. Designers should consult the manufacturer product page and datasheet for complete clock, memory, GPIO, timer, communication, and electrical characteristics before finalizing a board. Typical uses include low-power sensor nodes, compact industrial controls, battery-powered monitoring equipment, building automation endpoints, and small accessory controllers. The MCU is also appropriate for wearable-adjacent and portable products where board area and energy efficiency are important. In each case, the device can consolidate basic control and sensing tasks while preserving a straightforward firmware-development path. The primary design consideration is package and firmware planning. Use the datasheet pin-description and package drawings when assigning board tracks, programming connections, decoupling, clock components, and reset circuitry. Confirm that the firmware image, peripheral configuration, startup code, and development toolchain are compatible with the exact STM32L051C8T7 configuration before production release. This product page combines the manufacturer specifications, distributor listing details, same-family replacement information, package-level selection guidance, and practical design considerations to support faster component evaluation. It helps engineers distinguish exact configuration changes from genuinely interchangeable options and identify when firmware or qualification review is required before substitution.

詢價 聯絡我們
STM32L051K6T6 - 32MHz 32KB Cortex-M0+ MCU | STMicroelectronics
STM32L051K6T6

STM32L051K6T6 - 32MHz 32KB Cortex-M0+ MCU | STMicroelectronics

The STMicroelectronics STM32L051K6T6 is an ultra-low-power, 32-bit Arm Cortex-M0+ microcontroller operating at 32 MHz, with 32 KB (32K x 8) of Flash memory and 25 I/O pins in a 32-LQFP (7x7) package. It belongs to STMicroelectronics' access-line STM32L0 family and is designed for compact, energy-sensitive embedded-control products. A microcontroller is a semiconductor that integrates a processor core, program memory, data memory, peripherals, and input/output interfaces into one device. In the product hierarchy, the STM32L051K6T6 is an MCU, a general-purpose integrated circuit used to execute firmware and supervise connected hardware. Its Arm Cortex-M0+ core provides a compact, energy-efficient architecture for control-oriented rather than high-compute workloads. The verified device data identifies a 32-bit operating architecture, a maximum stated frequency of 32 MHz, 32 KB of Flash, and a 32-LQFP package. Distributor listings also identify a 12-bit ADC and 25 I/O pins. These resources make the device suitable for low-power sensing, actuator control, simple communications, and embedded products where a larger Cortex-M3 or Cortex-M4 processor would add unnecessary cost, board area, or energy consumption. The STM32L051K6T6's 32 MHz Cortex-M0+ core is positioned for energy-conscious control applications, while its 32 KB Flash capacity supports firmware, configuration data, and boot logic on one device. Its LQFP construction provides visible leads for inspection and repair, unlike fine-pitch land-grid-array packages. Exact RAM capacity, peripheral timing, and detailed electrical limits should be confirmed in the manufacturer datasheet for the final design. Typical uses include battery-powered environmental sensors, compact industrial monitoring nodes, access-control peripherals, low-power motor-control modules, and connected instrumentation. A designer can use the ADC for analog measurements and the GPIO structure for switches, indicators, sensors, and actuators, subject to the complete pin and peripheral assignments in the datasheet. The most important design consideration is to verify every alternate-function assignment and operating condition against the STM32L051K6T6 datasheet before PCB release. The 32-LQFP footprint should be checked for pin clearance, thermal exposure, and assembly capability, while firmware should use only the peripherals and interrupt assignments supported by the exact orderable device. This product record consolidates verified manufacturer and distributor information, current purchasing references, package details, application guidance, and same-family drop-in alternatives. It also identifies information that requires confirmation from the full datasheet rather than estimating unspecified RAM, timing, temperature, or pin-function values.

詢價 聯絡我們
STM32L051K8T6 - 32MHz Arm Cortex-M0+ MCU | STMicroelectronics
STM32L051K8T6

STM32L051K8T6 - 32MHz Arm Cortex-M0+ MCU | STMicroelectronics

The STMicroelectronics STM32L051K8T6 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller operating at 32 MHz, with 64 KB of Flash memory and 8 KB of RAM in a 32-LQFP 7 x 7 mm package. It also provides 2 KB of data EEPROM, a 12-bit 10-channel ADC, and up to 27 GPIO for compact energy-sensitive embedded systems. An ultra-low-power microcontroller is an integrated computing device designed to perform control, measurement, and communications tasks while minimizing energy consumption between active processing periods. The STM32L051K8 belongs to the STM32L0 access-line hierarchy: microcontroller, embedded processor, Arm Cortex-M0+ MCU, and semiconductor. This positioning makes it suitable for small systems that need more processing capability than a simple logic device but value compactness, low power, and broad peripheral integration. Key features include 64 KB of Flash for firmware, 8 KB of SRAM for working data, and 2 KB of EEPROM for parameters that must retain their values without power. The device provides three general-purpose timers, one basic timer, one low-power timer, one SPI or I2S interface, one I2C interface, and two USART interfaces. Its 12-bit, 10-channel synchronized ADC supports embedded analog measurement, while as many as 27 GPIO allow direct connection of sensors, switches, displays, and actuators. The STM32L051K8T6 uses the high-performance 32 MHz Arm Cortex-M0+ core within the STM32L0 product family. Serial wire debug provides a compact programming and debugging connection, reducing the number of external pins and board area required during development. The part combines 32-bit processing, integrated analog conversion, timer-based control, and serial communications in one 32-LQFP package, reducing the component count of compact control boards. Typical applications include battery-powered sensor nodes, industrial condition-monitoring equipment, compact building-control modules, low-power data loggers, consumer accessories, and portable measurement instruments. Designers can use the ADC for analog inputs, timers for periodic sampling or PWM generation, and the I2C, SPI, and USART peripherals for sensors, memory, displays, or external communications modules. A key design consideration is power management. Engineers should use the device's low-power operating modes when the application spends substantial time idle, while confirming the required supply range, operating temperature, and peripheral clock configuration in the manufacturer documentation before releasing the PCB. This page also synthesizes verified distributor pricing, package details, alternatives, and practical implementation guidance for STM32L051K8T6 evaluation.

詢價 聯絡我們
STM32L051R8H6 - 32MHz Cortex-M0+ 64KB MCU | STMicroelectronics
STM32L051R8H6

STM32L051R8H6 - 32MHz Cortex-M0+ 64KB MCU | STMicroelectronics

STMicroelectronics STM32L051R8H6 is an ultra-low-power 32-bit microcontroller with an Arm Cortex-M0+ core, 32 MHz maximum operating frequency, and 64 KB of embedded Flash memory. It is supplied in a 64-pin TFBGA package measuring 5 mm by 5 mm. The STM32L051 access-line family targets compact, energy-conscious embedded systems where processing performance, memory density, and a small board area must coexist. A microcontroller is a programmable system-on-chip that integrates a processor core, Flash program memory, SRAM, peripherals, and communication interfaces on one package. The STM32L0 product hierarchy combines an Arm Cortex-M0+ core with ultra-low-power design techniques for battery-powered sensors, industrial controls, connected equipment, and consumer devices. Its 32-bit architecture supports compact instruction decoding, efficient event handling, and real-time control without requiring a separate external processor. Key characteristics include a 32 MHz operating frequency, 64 KB of Flash, a 12-bit ADC, and an operating temperature range from -40 °C to +85 °C. The device belongs to STMicroelectronics' STM32L051x6/x8 access-line range, combining general-purpose embedded control with low-power operation. Its 64-pin TFBGA footprint supports dense PCB layouts while providing a broad selection of I/O and peripheral functions. The Arm Cortex-M0+ processor uses a compact instruction set designed for cost- and power-sensitive embedded applications. Firmware execution, peripheral configuration, and interrupt handling are managed within the integrated microcontroller, reducing the component count compared with separate processor, memory, and interface solutions. The 64 KB Flash provides room for application code, configuration data, and boot logic, while the access-line positioning supports straightforward embedded product development. Typical uses include low-power sensor nodes, industrial monitoring modules, compact motor controllers, wearable accessories, smart-home endpoints, and battery-operated measurement equipment. The small 5 mm by 5 mm TFBGA package is especially useful where PCB area is constrained, although fine-pitch assembly, inspection, and rework require suitable manufacturing capability. For a new design, verify the exact pin assignments, exposed-pad requirements, decoupling network, clock configuration, and peripheral assignments against the manufacturer datasheet and package drawing. Because this part uses a fine-pitch ball-grid array, PCB design should include the required land pattern, via-in-pad considerations where appropriate, thermal-via strategy, and assembly tolerances before schematic sign-off. This product page combines manufacturer and distributor technical information with pin-compatible family alternatives, application guidance, comparison criteria, and practical PCB considerations to support component selection, design review, and sourcing decisions for the STM32L051R8H6.

詢價 聯絡我們
STM32L051R8T6 - 32MHz Cortex-M0+ 64KB MCU | STMicroelectronics
STM32L051R8T6

STM32L051R8T6 - 32MHz Cortex-M0+ 64KB MCU | STMicroelectronics

STMicroelectronics STM32L051R8T6 is an ultra-low-power 32-bit microcontroller based on the Arm Cortex-M0+ processor core, operating at up to 32 MHz and incorporating 64 KB of Flash memory. The device is supplied in a 64-pin LQFP package measuring 10 mm by 10 mm. Its combination of a 32-bit RISC core, compact surface-mount package and 64 KB program memory makes it suitable for embedded control, sensing, communication and low-power monitoring systems. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripheral interfaces and clocking circuitry into one package. The STM32L0 series belongs to the hierarchy of embedded microcontroller, 32-bit RISC processor, embedded processor and semiconductor. Applications commonly require a compact controller that can execute firmware, acquire data, control outputs and communicate with sensors or other system components without requiring a separate processor and memory devices. The STM32L051R8T6 uses an Arm Cortex-M0+ core capable of 32 MHz operation and provides 64 KB of Flash memory, organized as 64K by 8 bits. Its 64-LQFP 10 mm by 10 mm package supports surface-mount assembly and provides a mechanically substantial alternative to smaller leadless packages. The STMicroelectronics product family is identified as an access-line, ultra-low-power MCU family, making the device relevant to designs where operating efficiency and integration are important. The exact peripheral set, RAM capacity, supply limits, pin assignments, clock tree and electrical characteristics are governed by the manufacturer documentation for the STM32L051x6 and STM32L051x8 device family. Firmware selection should account for the specific order code, package drawing, exposed peripheral pins and errata information. Because firmware and board support are closely tied to silicon revision, developers should treat the complete order code as the controlling device identifier. Typical application directions include compact environmental sensors, industrial sensing nodes, low-power data loggers, actuator controllers, communications modules and embedded accessories. In these systems, the Cortex-M0+ instruction set handles real-time control tasks, while the integrated Flash memory stores application firmware. The 64-pin LQFP package can also make prototype assembly and signal access more convenient than a very small leadless package. PCB planning should preserve the LQFP-64 footprint, pad geometry, pin-1 orientation and all exposed leads. Decoupling, grounding, clock stability and unused-pin treatment must follow the manufacturer reference design and device documentation. Software bring-up should also verify the low-power mode configuration, peripheral clock gates and debugger connection because these details affect both energy use and board-level reliability. This product record combines the exact order-code attributes, package information, commercial inquiry workflow, drop-in candidates and application-oriented engineering guidance in one concise reference. It helps engineers distinguish the STM32L051R8T6 from related MCU options before committing the 64-LQFP footprint to a PCB.

詢價 聯絡我們
STM32L052C8T6 - 32MHz Cortex-M0+ 64KB MCU | STMicroelectronics
STM32L052C8T6

STM32L052C8T6 - 32MHz Cortex-M0+ 64KB MCU | STMicroelectronics

The STMicroelectronics STM32L052C8T6 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller with a 32 MHz maximum clock, 64 KB of Flash memory, and a 48-LQFP 7 mm × 7 mm package. It integrates one 12-bit ADC with hardware oversampling, one DAC, two ultra-low-power comparators, multiple timers, an RTC, and USB 2.0 crystal-less connectivity for compact control and sensor systems. An ultra-low-power microcontroller is an embedded semiconductor that combines a processor core, memory, analog interfaces, timers, and communication peripherals while minimizing energy use during active, sleep, and standby operation. The STM32L0 series belongs to the Arm Cortex-M microcontroller hierarchy and is designed for battery-powered instruments, connected sensors, industrial controls, and other systems where low standby current and compact integration are central requirements. The STM32L052C8T6 provides 64 KB of Flash and a 32 MHz Arm Cortex-M0+ processor. Its analog subsystem includes one 12-bit ADC with hardware oversampling and one DAC, while two comparators support low-power threshold detection. The device also provides USB 2.0 crystal-less connectivity, one RTC, one SysTick timebase, three general-purpose 16-bit timers, one basic timer, one low-power timer, and two watchdogs. Its peripheral mix supports both event-driven sensing and periodic control. Hardware oversampling can improve effective ADC resolution when the application can accept a longer conversion sequence, while the DAC enables analog output from a compact controller. The crystal-less USB interface simplifies designs that do not require an external USB clock source, although final firmware and board-level validation remain necessary. Typical uses include USB-connected low-power data loggers, industrial sensor nodes, compact environmental monitors, battery-powered accessories, and USB-to-serial or configuration interfaces. The 48-LQFP package also exposes more I/O than smaller microcontroller packages, making the device useful when a board needs USB, mixed analog inputs, and several timers without moving to a higher pin count. Designers should preserve USB signal integrity with a controlled impedance PCB layout, place decoupling capacitors close to the supply pins, and follow the pin-description table in the manufacturer datasheet when assigning board functions. Verify oscillator, USB, analog-reference, and low-power-mode requirements against the electrical characteristics before releasing a production layout. This page organizes the core MCU specifications, package details, application guidance, design considerations, and qualified drop-in alternatives into a single engineering reference for evaluating the STM32L052C8T6 in new or existing 48-LQFP designs.

詢價 聯絡我們
STM32L052K6T6 - 32MHz USB Cortex-M0+ MCU | STMicroelectronics
STM32L052K6T6

STM32L052K6T6 - 32MHz USB Cortex-M0+ MCU | STMicroelectronics

The STMicroelectronics STM32L052K6T6 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller operating at up to 32 MHz, with 32 KB of Flash memory and USB 2.0 crystal-less connectivity in a 32-LQFP 7x7 mm package. It combines low-power embedded control with serial peripherals for connected industrial, IoT, sensor, and USB-powered products. A microcontroller is a semiconductor that integrates a processor core, programmable memory, digital I/O, and peripherals into one device. The STM32L0 family belongs to the ARM Cortex-M microcontroller hierarchy and targets embedded systems where compact size, efficient processing, and low standby or operating power are important. Its peripheral integration reduces the component count needed for communications, timing, analog measurement, and control. The verified product information identifies an ARM Cortex-M0+ core, 32 MHz operation, 32 KB Flash organized as 32K x 8, USB 2.0 crystal-less connectivity, and a 32-LQFP package. Distributor listings also identify I2C and SPI support, making the device relevant for sensor networks, USB-to-serial equipment, compact control boards, and low-power connected products. The exact SRAM, voltage range, temperature limits, and peripheral ratings were not supplied in the verified excerpts and therefore are not asserted here. The crystal-less USB feature is a practical differentiator for designs that need USB connectivity without relying on a dedicated external crystal for the specified USB implementation. Firmware must still satisfy the USB clocking, impedance, power, and enumeration requirements described by the manufacturer. The 32 MHz Cortex-M0+ core provides a responsive platform for control logic while retaining the STM32 family's low-power positioning. Typical applications include low-power IoT nodes, USB-connected sensors, industrial instrumentation, low-power control boards, compact data-acquisition products, and embedded automation modules. These uses benefit from the MCU's combination of USB, I2C, SPI, Flash, and a compact 32-LQFP footprint. The 7x7 mm package is easy to route on a reasonably dense PCB while preserving exposed assembly and inspection access. Designers should verify the complete pinout, alternate-function mapping, power requirements, decoupling recommendations, clocking scheme, and USB layout against the official STM32L052K6 datasheet before layout release. USB differential routing, ground-return continuity, input filtering, and exposed-pad thermal design are more important than simply matching the package outline. Firmware should also confirm peripheral mapping and low-power-mode timing rather than assuming that a lower-power alternative is automatically interchangeable. This page combines verified distributor and manufacturer listings with structured application, comparison, and design guidance. It is intended to help engineers identify the correct STM32L052K6T6 platform while separating confirmed data from parameters that still require direct datasheet confirmation.

詢價 聯絡我們
STM32L052K6U6 - 32MHz USB Cortex-M0+ MCU | STMicroelectronics
STM32L052K6U6

STM32L052K6U6 - 32MHz USB Cortex-M0+ MCU | STMicroelectronics

STMicroelectronics STM32L052K6U6 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller with a 32 MHz maximum clock, 32 KB flash memory, and USB 2.0 crystal-less connectivity in a 32-pin UFQFPN package measuring 5 mm by 5 mm. The device is designed for energy-sensitive embedded systems that require compact control, serial connectivity, timers, and low power operation. A microcontroller is a programmable integrated circuit containing a processor core, memory, peripherals, and input/output interfaces. The STM32L0 series belongs to the ARM Cortex-M0+ class of embedded processors, combining a compact instruction set with broad peripheral integration. This product hierarchy places the STM32L052K6U6 within microcontrollers, embedded processors, and the broader semiconductor category. Key verified features include a 32-bit ARM Cortex-M0+ core, operation up to 32 MHz, 32 KB flash, and USB 2.0 crystal-less connectivity. The 32-pin UFQFPN package supports compact surface-mount layouts where board area is constrained. Its low-power positioning makes it relevant for connected sensors, USB peripherals, industrial controls, and battery-operated equipment, provided that the selected operating modes and peripheral requirements are confirmed against the manufacturer documentation. The part is suitable when a design needs an Arm Cortex-M0+ control core, USB connectivity, and a compact package. Its 32 MHz clock specification provides a clear performance target for embedded firmware, while the 32 KB flash capacity should be checked carefully against application code size, bootloader requirements, and future updates. The crystal-less USB feature can simplify clock integration, but USB layout, power, firmware, and signal-integrity requirements still require careful implementation. Before design release, verify the complete pin assignment, electrical limits, memory map, USB support, operating-temperature grade, and package land pattern in the official STMicroelectronics documentation. The supplied verified data confirms the core, clock, flash, USB connectivity, package, and distributor identity, but it does not provide every electrical or pin-level parameter required for a complete hardware design. This product page combines verified manufacturer and distributor information, structured specifications, application guidance, and design considerations. It is intended to support component identification and sourcing while clearly identifying details that still require confirmation from the official STM32L052K6 datasheet.

詢價 聯絡我們
STM32L052K8T6 - 32MHz Cortex-M0+ 64KB MCU | STMicroelectronics
STM32L052K8T6

STM32L052K8T6 - 32MHz Cortex-M0+ 64KB MCU | STMicroelectronics

STMicroelectronics STM32L052K8T6 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller with a 32 MHz CPU, 64KB of Flash, USB 2.0 crystal-less connectivity, and a 32-LQFP 7 x 7 mm package. The STM32L0 series targets compact embedded products that require efficient processing and low standby power without the resource demand of a higher-performance microcontroller. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripherals, and communication interfaces into one device. In the product hierarchy, the STM32L052K8T6 is an Arm Cortex-M0+ MCU, an STM32L0-series microcontroller, a 32-bit embedded controller, and an ultra-low-power semiconductor. It is suited to connected sensors, compact USB devices, industrial modules, and portable products requiring USB and serial peripherals. The manufacturer product information identifies a 32 MHz operating frequency, 64KB organized as 64K x 8 Flash, a 32-bit architecture, and USB 2.0 crystal-less connectivity. Listed communication capabilities also include I2C and SPI. These features allow the device to move data between sensors, actuators, storage, and a USB host while retaining the low-power operating characteristics associated with the STM32L0 family. STM32L052K8T6 integrates several embedded peripherals into a single 32-LQFP package. Its 64KB Flash provides program storage for control logic, communication firmware, and configuration data. The Cortex-M0+ architecture provides a compact instruction set suited to real-time embedded workloads, while the documented I2C and SPI interfaces support common industrial and consumer peripherals. USB 2.0 crystal-less operation is particularly relevant to designs that need direct connectivity without a separate external USB clock source. Typical applications include low-power USB sensor nodes, compact data loggers, industrial condition-monitoring modules, building controls, and wearable or portable accessories. The 7 x 7 mm LQFP footprint is large enough for accessible manufacturing and inspection while remaining suitable for space-conscious boards. Firmware can collect sensor readings over I2C or SPI, store operational information in Flash, and communicate with a host through USB. A primary design consideration is power-budget allocation across active, sleep, and shutdown operation. Firmware should disable unused peripherals, configure clock sources correctly, and select the lowest-energy mode compatible with wake-up requirements. Because USB clocking, external interfaces, and analog functions can affect current consumption, measure the complete assembled product under realistic traffic and environmental conditions rather than relying only on nominal processor activity. This product page combines the manufacturer specifications with package, interface, application, replacement, and procurement guidance. It also distinguishes true same-footprint candidates from options that require package or firmware changes, helping engineers evaluate the STM32L052K8T6 for embedded USB, low-power sensing, and connected-control designs.

詢價 聯絡我們
STM32L052K8U6 - 32MHz Cortex-M0+ USB MCU | STMicroelectronics
STM32L052K8U6

STM32L052K8U6 - 32MHz Cortex-M0+ USB MCU | STMicroelectronics

STMicroelectronics STM32L052K8U6 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller operating at 32 MHz, with 64 KB of Flash memory and crystal-less USB 2.0 connectivity in a 32-pin UFQFPN 5 x 5 mm package. The device combines a compact embedded-control footprint with analog conversion, timing, real-time-clock, watchdog, and low-power peripherals for connected sensing and control designs. An ultra-low-power microcontroller is an embedded semiconductor designed to execute firmware while minimizing energy consumption between active processing intervals. The STM32L0 family belongs to the MCU hierarchy, extending from general-purpose embedded processors into low-power systems for battery-operated instruments, industrial sensors, compact data loggers, USB accessories, and compact consumer equipment. Its low-power focus makes the STM32L052K8U6 suitable for systems that spend substantial time in sleep or low-power operating modes. Key features include a 32-bit Arm Cortex-M0+ processor, 64 KB Flash, a 12-bit ADC with hardware oversampling, one DAC, two ultra-low-power comparators, three general-purpose 16-bit timers, one low-power timer, one basic timer, an RTC, and SysTick. Two watchdogs provide independent and windowed watchdog functions, while USB 2.0 support can operate without a crystal according to the manufacturer product information. The STM32L052x6/8 architecture integrates the analog and timing resources needed to reduce external component count. The ADC, DAC, comparators, RTC, and multiple timer types can support signal acquisition, local excitation, waveform generation, event detection, and periodic sampling. USB crystal-less operation can simplify peripheral layouts, although firmware, clock configuration, power budgeting, and signal-integrity validation remain necessary for each board design. Typical applications include USB-connected sensors, compact environmental monitors, industrial measurement modules, low-power data loggers, wearable accessories, and embedded control boards requiring both analog inputs and USB connectivity. The 32-pin 5 x 5 mm package also supports space-constrained products while retaining a generous peripheral set for general-purpose embedded applications. Designers should verify startup behavior, clock tolerance, USB electrical characteristics, decoupling, and low-power mode timing against the manufacturer datasheet. Place the required input, output, and analog bypass capacitors close to their associated pins, provide a clean ground return, and confirm that the exposed-pad thermal and assembly requirements match the PCB layout. This product overview combines the manufacturer's core MCU specifications with practical application guidance, package-aware comparison information, and engineering considerations for USB, analog, power, and PCB implementation. It is intended to help engineers evaluate the STM32L052K8U6 against same-package alternatives before committing to a board layout.

詢價 聯絡我們
STM32L052R8H6 - 32MHz USB Cortex-M0+ MCU | STMicroelectronics
STM32L052R8H6

STM32L052R8H6 - 32MHz USB Cortex-M0+ MCU | STMicroelectronics

The STMicroelectronics STM32L052R8H6 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller operating at up to 32 MHz, with 64 KB of Flash memory, 8 KB of SRAM, and USB connectivity in a 64-TFBGA package measuring 5 x 5 mm. It combines embedded USB connectivity with peripheral resources suited to compact, energy-conscious embedded systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals on one package. The STM32L0 product family belongs to the hierarchy of embedded microcontroller, 32-bit processor, Arm Cortex-M microcontroller, and low-power embedded controller. This product type allows one device to execute application firmware, acquire sensor data, control outputs, and communicate with a host or other embedded systems. Key features include 64 KB of Flash, 8 KB of SRAM, 2 KB of EEPROM, USB 2.0 support, and 12-bit ADC and DAC resources. Its Arm Cortex-M0+ core operates at up to 32 MHz, providing adequate performance for low-power control, sensor monitoring, data acquisition, human-interface equipment, and USB-connected peripheral designs. The compact 64-TFBGA package supports space-constrained boards but requires careful PCB layout and inspection because its ball grid provides fine-pitch routing opportunities. The STM32L052R8H6 is designed for embedded applications where low power, USB connectivity, and moderate processing performance are important. Its architecture sits between simple fixed-function controllers and more complex application processors. Firmware can use the Cortex-M0+ instruction set while USB provides a standard peripheral interface for configuration, data exchange, and control. The manufacturer positions the STM32L052x6 and STM32L052x8 devices as ultra-low-power microcontrollers with USB 2.0 crystal-less connectivity. Typical uses include compact USB sensor nodes, industrial monitoring modules, USB-connected control panels, compact instrumentation, and low-power embedded accessories. USB connectivity can reduce the number of external interface components, while the 32 MHz core and 8 KB SRAM allow local control logic to execute without a higher-power processor. Designers should select the correct clock, USB transceiver, decoupling, and programming configuration from the manufacturer documentation. PCB implementation requires careful treatment of the 64-TFBGA land pattern, power routing, and exposed-pad or thermal-management requirements specified for the exact package variant. Firmware development should follow the STM32CubeMX and STM32Cube programming workflow where supported. USB firmware should use the device's supported crystal-less USB configuration and validate enumeration timing across the intended host, power, and bus conditions. This product page combines the manufacturer product information, distributor specifications, package details, and practical design guidance in a format that helps engineers evaluate the STM32L052R8H6 for low-power USB embedded designs. It also identifies where a true pin-compatible replacement cannot yet be confirmed, preventing a merely similar microcontroller from being presented as a drop-in substitute.

詢價 聯絡我們
STM32L052R8T6 - 32MHz 64KB USB MCU | STMicroelectronics
STM32L052R8T6

STM32L052R8T6 - 32MHz 64KB USB MCU | STMicroelectronics

The STMicroelectronics STM32L052R8T6 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller with a 32 MHz maximum CPU frequency, 64 KB of Flash memory, and USB 2.0 crystal-less connectivity in a 64-LQFP 10 x 10 mm package. The device combines an energy-efficient embedded design with USB connectivity for compact, low-power electronic products. An ultra-low-power microcontroller is a semiconductor designed to complete control and connectivity tasks while minimizing energy consumption during active operation and low-power modes. In the product hierarchy, the STM32L052R8T6 is an MCU, an embedded processing IC, and a member of STMicroelectronics' STM32L0 family. Its compact package and USB interface make it suitable for devices that need firmware-driven control, data exchange, and low standby demand without requiring a higher-power application processor. Key verified features include an ARM Cortex-M0+ core, 32-bit processing, operation up to 32 MHz, and 64 KB of programmable Flash. The integrated connectivity supports USB 2.0 operation without an external crystal, while the specified 2.5 V and 3.3 V operating voltages support conventional embedded supply environments. The STM32L052x6/8 family is positioned by STMicroelectronics as an ultra-low-power platform for connected, compact products. The 64-LQFP package exposes substantially more I/O than smaller microcontroller packages, allowing designers to connect external sensors, displays, communication transceivers, and control interfaces without moving to a more complex device. At the same time, the Cortex-M0+ architecture keeps the MCU suitable for embedded control rather than demanding graphical or high-throughput workloads. Exact RAM, peripheral, timer, GPIO, and electrical limits are not present in the supplied excerpts and should be confirmed in the manufacturer datasheet. Typical applications include USB-connected sensors, compact industrial controls, medical-device peripherals, battery-operated accessories, USB-to-data acquisition systems, and low-power monitoring equipment. The crystal-less USB capability can simplify connector-based products when the final board design and firmware satisfy STMicroelectronics' USB clocking requirements. The main design consideration is package and firmware validation. Engineers should confirm the complete 64-pin assignment, USB impedance routing, decoupling, clocking, and peripheral configuration against the manufacturer documentation. This page combines verified distributor specifications, pricing context, same-family alternatives, and practical sourcing guidance that is not consolidated in a single manufacturer excerpt.

詢價 聯絡我們
STM32L053C6T6 - 32MHz Ultra-Low-Power MCU | STMicroelectronics
STM32L053C6T6

STM32L053C6T6 - 32MHz Ultra-Low-Power MCU | STMicroelectronics

STMicroelectronics STM32L053C6T6 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller with a 32 MHz operating frequency, 32 KB of Flash memory, USB 2.0 connectivity, and a 48-LQFP 7 x 7 mm package. It operates from 1.8 V to 3.6 V with brown-out detection, or down to 1.65 V in power-down mode, and supports an extended -40°C to +125°C temperature range. An ultra-low-power microcontroller is a semiconductor designed to minimize energy consumption while retaining the processing, memory, and peripheral capabilities needed for embedded control. The STM32L0 series belongs to the ARM Cortex-M0+ microcontroller hierarchy and combines a compact general-purpose processor with energy-saving modes, making it suitable for battery-operated, portable, and connected devices. The STM32L053C6T6 includes 32 KB of Flash, a 32 MHz ARM Cortex-M0+ core, USB 2.0 crystal-less connectivity, and an LCD-capable feature set. Its 1.8 V to 3.6 V operating supply supports low-energy embedded systems. A broad temperature option from -40°C to +125°C supports industrial and extended-temperature environments when the appropriate ordering variant is specified. The device's low-power architecture includes multiple power-saving modes for designs that spend substantial time idle. USB connectivity adds a practical interface for configuration, data exchange, and firmware update workflows, while the Cortex-M0+ core provides a 32-bit execution environment suitable for control logic, communications, and compact user interfaces. Typical applications include USB-connected sensors, low-power data loggers, compact industrial controllers, wearable and portable devices, and USB-to-LCD interface equipment. In each case, the combination of 32 KB Flash, a 32 MHz core, USB 2.0, and low-power operating modes supports a useful balance of capability, board area, and energy efficiency. Designers should verify the exact pin functions, peripheral availability, memory map, and exposed-pin configuration against the manufacturer datasheet before layout. USB signal routing, crystal-less operation, decoupling, and low-power mode entry are especially important because they affect firmware scheduling, EMI performance, and reliable peripheral communication. This page combines manufacturer specifications, distributor pricing, pin-compatible alternatives, comparison parameters, and practical design guidance. It also distinguishes verified facts from parameters requiring direct review of the STM32L053x6/8 datasheet, helping engineers source the device without relying on unverified substitutions.

詢價 聯絡我們
STM32L053C8T6 - Ultra-Low-Power ARM Cortex-M0+ MCU | STMicroelectronics
STM32L053C8T6

STM32L053C8T6 - Ultra-Low-Power ARM Cortex-M0+ MCU | STMicroelectronics

The STMicroelectronics STM32L053C8T6 is an ultra-low-power 32-bit microcontroller based on the ARM Cortex-M0+ core, operating at up to 32 MHz. It features 64 KB of Flash memory and 8 KB of SRAM, with a rich set of peripherals including USB 2.0, 12-bit ADC, DAC, comparators, and multiple communication interfaces. The device is housed in a 48-pin LQFP package, making it suitable for space-constrained applications. An ultra-low-power microcontroller (MCU) is a system-on-chip that integrates a processor core, memory, and peripherals, optimized for minimal energy consumption. The STM32L0 series is part of the STM32 family, which spans from entry-level Cortex-M0+ to high-performance Cortex-M7 cores. These MCUs are designed for battery-powered and energy-harvesting applications where power efficiency is critical, often featuring multiple low-power modes and dynamic voltage scaling. Key features include multiple low-power modes (Sleep, Low-power Run, Low-power Sleep, Stop with RTC, Standby with RTC), a 12-bit ADC with hardware oversampling, a 12-bit DAC, two ultra-low-power comparators, and a USB 2.0 crystal-less device. The device also integrates a real-time clock (RTC) with calendar and alarm functions, and a true EEPROM emulation. The operating voltage range is 1.8V to 3.6V, with a temperature range of -40°C to +85°C. The STM32L053C8T6 is built on ST's ultra-low-power technology, featuring a flexible power management that allows the core to run at 32 MHz while consuming only 84 µA/MHz in Run mode. The device supports a wide range of communication interfaces including I2C, SPI, USART, and LPUART, making it versatile for IoT and sensor applications. The integrated USB 2.0 interface supports both device and host modes, with a crystal-less design that reduces BOM cost. Typical applications include IoT sensor nodes, wearable devices, smart home controllers, industrial sensors, and portable medical devices. The ultra-low-power consumption and rich analog peripherals make it ideal for battery-powered systems that require long operational life. The device also supports firmware updates via USB or UART bootloader, simplifying field maintenance. When designing with this MCU, careful attention should be paid to the power supply decoupling and the selection of low-power modes to maximize battery life. The use of the internal 16 MHz HSI oscillator can reduce external component count, but for precise timing, an external crystal is recommended. The device's low-power modes require proper configuration of the RTC and wake-up sources to achieve optimal energy efficiency.

詢價 聯絡我們
STM32L053R8H6 - 32MHz Cortex-M0+ 64KB MCU | STMicroelectronics
STM32L053R8H6

STM32L053R8H6 - 32MHz Cortex-M0+ 64KB MCU | STMicroelectronics

The STMicroelectronics STM32L053R8H6 is an ultra-low-power 32-bit microcontroller based on the Arm Cortex-M0+ processor, operating at up to 32 MHz with 64 KB of Flash memory and 8 KB of SRAM. It is available in a 64-TFBGA 5x5 mm package and includes USB 2.0 connectivity, LCD support, ADC and DAC peripherals, and 2 KB of EEPROM. The device operates from 1.8 V to 3.6 V, with operation down to 1.65 V in power-down mode when the brown-out detector is disabled. An ultra-low-power microcontroller is an embedded semiconductor designed to perform control, measurement, communications, and data-processing tasks while minimizing energy consumption. The STM32L053 belongs to the STM32L0 low-power MCU family, combining a compact Cortex-M0+ core with energy-saving modes for battery-powered and always-connected products. Its USB, LCD, and mixed-signal peripherals reduce the need for external components in compact embedded systems. Key features include a 32 MHz Cortex-M0+ CPU, 64 KB of Flash, 8 KB of SRAM, 2 KB of EEPROM, USB 2.0 crystal-less connectivity, and an LCD controller. The MCU also integrates two ultra-low-power comparators sharing an internal or external reference voltage, plus ADC and DAC functions. These resources support low-power sensor nodes, USB-connected accessories, small human-machine interfaces, and portable measurement instruments. The STM32L053R8H6 provides a balanced architecture for embedded control applications where USB connectivity and low-power operation are more important than high processing throughput. Its 1.8 V to 3.6 V operating range accommodates single-cell lithium battery systems after suitable regulation, as well as 3.3 V industrial and consumer equipment. The wide -40 °C to +125 °C temperature range supports applications across industrial, automotive-adjacent, and extended-temperature environments. Typical applications include USB-connected industrial sensors, compact data loggers, low-cost USB power and monitoring accessories, LCD-equipped control panels, and battery-operated diagnostic instruments. The LCD controller is particularly useful for small local displays, while USB enables configuration, firmware updates, and data transfer over a standard serial interface. The ADC, DAC, and comparators support direct sensing and signal-conditioning functions. Designers should use the manufacturer pin-description table when assigning PCB tracks and should confirm the exposed-pad, power, decoupling, and programming requirements for the 64-TFBGA package. USB layout requires careful attention to signal integrity, impedance control, and the placement of its supporting components. Low-power designs should also account for the selected sleep, stop, and standby modes when defining the product's average-current budget. This product page combines the manufacturer device description and datasheet with practical packaging, application, replacement, and design guidance for engineers evaluating the STM32L053R8H6 in compact USB-enabled embedded products.

詢價 聯絡我們
STM32L053R8T6 - 32MHz Ultra-Low-Power Cortex-M0+ MCU | ST
STM32L053R8T6

STM32L053R8T6 - 32MHz Ultra-Low-Power Cortex-M0+ MCU | ST

The STMicroelectronics STM32L053R8T6 is an ultra-low-power 32-bit ARM Cortex-M0+ microcontroller with a maximum CPU frequency of 32 MHz, 64 KB of Flash memory, 8 KB of SRAM, and a 64-pin LQFP-64 (10x10 mm) package. What is an ultra-low-power microcontroller? It is an embedded processor optimized to minimize energy consumption while still providing enough compute for sensing, control, and communication tasks. It sits in the product hierarchy: microcontroller -> ARM Cortex-M0+ -> ultra-low-power MCU -> battery-powered embedded system. These devices rely on low-leakage process technology, flexible clock gating, and sleep/stop/standby modes to cut current draw to microamp or nanoamp levels, enabling multi-year operation from a coin cell. Key features include a USB 2.0 full-speed crystal-less device controller, an LCD driver supporting up to 8x28 segments, a 12-bit ADC with hardware oversampling, a 12-bit DAC, two ultra-low-power comparators, and a real-time clock with calendar. The STM32L053R8T6 runs from a 1.8 V to 3.6 V supply (down to 1.65 V in power-down without BOR), operates from -40C to +125C, and provides I2C, SPI, and USART serial interfaces. Technically, this MCU is built in a 110 nm ultra-low-leakage process. It integrates an NVIC, a memory protection unit, a true random number generator, a CRC calculation unit, and a unique 96-bit device ID. Typical Run-mode consumption is 84 uA/MHz, while Standby with RTC is only 0.29 uA. The flexible clock tree accepts an internal 16 MHz RC, an external crystal, or a 32.768 kHz oscillator for low-power RTC timekeeping. Typical applications include portable medical devices, wireless IoT sensor nodes, smart utility meters, wearable devices, and LCD-equipped industrial products. The very low standby current and configurable wake-up events make this MCU ideal for systems that must spend most of their life asleep and wake periodically to sample, log, or transmit. When designing with this device, place a 100 nF decoupling capacitor near each VDD pin and a 1 uF bulk capacitor on the main supply. Configure the RTC, EXTI, or USART wake-up sources to keep average current in the microamp range while preserving responsiveness. This page synthesizes distributor availability, drop-in STM32L0 alternatives, comparison data, and practical low-power design notes that are not reprinted in the datasheet, helping engineers select and validate the part faster.

詢價 聯絡我們
STM32L062K8T6 - 32MHz Cortex-M0+ USB MCU | STMicroelectronics
STM32L062K8T6

STM32L062K8T6 - 32MHz Cortex-M0+ USB MCU | STMicroelectronics

STMicroelectronics STM32L062K8T6 is an ultra-low-power, 32-bit Arm Cortex-M0+ microcontroller with a 32 MHz CPU, 64 KB of Flash memory, USB 2.0 crystal-less connectivity, and AES support, supplied in a 32-LQFP 7 x 7 mm package. It combines the STM32L0 low-power architecture with embedded USB connectivity, making it suitable for compact control, sensing, data-acquisition, and low-energy peripheral designs. An ultra-low-power microcontroller is an embedded processing device optimized to minimize energy consumption while retaining general-purpose control and communication functions. The STM32L062K8 belongs to the STM32L0 family, which combines a microcontroller core, Flash program memory, SRAM, peripheral interfaces, and low-power modes within one integrated circuit. Its position in the hierarchy is Arm Cortex-M0+ microcontroller, 32-bit microcontroller, embedded processor, and semiconductor. Verified device features include a 32 MHz operating frequency, 64 KB configured as 64K x 8 Flash, USB 2.0 crystal-less connectivity, AES capability, and a 32-LQFP package. The 64 KB Flash capacity provides space for embedded code, configuration data, and firmware updates, while the Cortex-M0+ core provides a 32-bit instruction set designed for resource-constrained embedded control. The integrated USB interface allows the MCU to connect directly as a USB device without an external USB transceiver. The T6 ordering suffix identifies the temperature and package configuration used for this exact ordering code. The supplied distributor records identify the device as a 32-LQFP 7 x 7 mm microcontroller, while other ordering codes in the STM32L062K8 family may use a different package or temperature grade. Consequently, engineers should validate the exact pinout, electrical limits, clock configuration, USB implementation, and operating-temperature grade before substituting another orderable code. Typical applications include USB-connected sensor nodes, compact industrial controllers, low-power data loggers, USB-to-serial equipment, battery-operated monitoring systems, and embedded USB accessories. In each case, the combination of a 32 MHz Cortex-M0+ core, 64 KB Flash, and crystal-less USB connectivity can reduce the number of external components and simplify firmware-based control. The LQFP package also exposes pins for prototyping, inspection, and hand-soldering where appropriate. Designers should pay particular attention to USB clocking, decoupling, power sequencing, and firmware initialization. Crystal-less USB operation does not remove the need for a compliant USB power and signal implementation. Input and output capacitors must be placed close to the supply pins, USB data routing must minimize distortion, and firmware must follow the clock, transceiver, and low-power requirements published in the manufacturer documentation. This product page consolidates the verified manufacturer and distributor information for the STM32L062K8T6, distinguishes confirmed characteristics from data requiring engineering review, and provides selection and design guidance that goes beyond a distributor specification summary. It also identifies same-package alternatives without treating different package codes as drop-in replacements.

詢價 聯絡我們