積體電路

子分類

📁 ADC/DAC 3,100+ 產品 📁 放大器 IC 1,900+ 產品 📁 音訊編解碼器 18 產品 📁 音訊 IC 2 產品 📁 時脈與計時 670+ 產品 📁 Comparator ICs 1 產品 📁 DSP 1,100+ 產品 📁 資料擷取 IC 2 產品 📁 數位電位器 4 產品 📁 顯示驅動器與控制器 1 產品 📁 FPGA 與 CPLD 7,300+ 產品 📁 介面 IC 3,400+ 產品 📁 LED 驅動器 1 產品 📁 邏輯 IC 460+ 產品 📁 記憶體 IC 870+ 產品 📁 微控制器 20,000+ 產品 📁 微處理器 4 產品 📁 馬達驅動器 1 產品 📁 其他 1 產品 📁 感測器與偵測器介面 1 產品 📁 特殊用途 IC 15 產品 📁 視訊 IC 14 產品

產品（39,000+)

DSPIC30F6012A-20I/PT - 16-bit DSC, 144KB Flash, 20 MIPS | Microchip
DSPIC30F6012A-20I/PT

DSPIC30F6012A-20I/PT - 16-bit DSC, 144KB Flash, 20 MIPS | Microchip

The Microchip Technology DSPIC30F6012A-20I/PT is a 16-bit Digital Signal Controller (DSC) that combines MCU simplicity with DSP performance, providing up to 20 MIPS at 4.5-5.5 V supply voltage and integrating 144 KB (48K x 24) of Flash program memory with 8 KB RAM in a 64-pin TQFP (10x10 mm) package. The dsPIC30F core executes most instructions in one cycle and includes a hardware multiply-accumulate (MAC) engine that delivers deterministic DSP throughput for closed-loop control and digital filtering. A Digital Signal Controller (DSC) is a hybrid device that merges a microcontroller's deterministic peripherals and ease of use with a digital signal processor's parallel computational engine. The dsPIC30F family targets 5 V systems that benefit from wide operating voltage, integrated EEPROM emulation, and an instruction set optimized for embedded motor-control and power-conversion algorithms. DSCs sit hierarchically between MCUs and DSPs, addressing applications that need real-time numeric computation without the complexity of a standalone DSP. Key features of the DSPIC30F6012A-20I/PT include 60 I/O pins, two CAN modules, two UART/USART ports, I2C, SPI, two 16-bit timers, an 8-channel 10-bit ADC at 1 Msps, and a 16-bit motor-control PWM with up to 8 outputs. The 144 KB Flash supports self-programming and is partitioned for fault-tolerant boot, and 8 KB RAM plus 4 KB auxiliary Flash provide ample headroom for code and data buffers in motor-control and power-conversion firmware stacks. Architecturally, the device integrates a 16-bit modified Harvard core with a 24-bit-wide instruction word and a 16-bit DSP engine that performs a 16x16-bit multiply in one cycle. The peripheral set is engineered for real-time control: a motor-control PWM block with dead-time generation, a quadrature encoder interface, and high-speed analog comparators streamline digital control loops for three-phase motor drives, uninterruptible power supplies, and power-factor correction stages. Typical applications include three-phase AC induction and brushless DC (BLDC) motor control, switched-mode power supplies with digital control loops, automotive body and chassis modules, industrial automation, and power-conversion systems. The dsPIC30F family offers seamless migration paths to dsPIC33F and PIC24 devices in similar packages for designs that need additional MIPS or peripheral scaling. When designing with the DSPIC30F6012A-20I/PT, plan the PCB layout to keep ADC traces short and isolated from PWM switching nodes, and decouple each VDD/VSS pair with a 0.1 microfarad ceramic plus a bulk capacitor to suppress switching-noise coupling into the analog front end. This page synthesizes distributor pricing, drop-in alternatives from the same dsPIC30F6011A/6012A/6013A/6014A family, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
DSPIC30F6012AT-20E/PF - 16-bit DSC, 144KB Flash, 20 MIPS | Microchip
DSPIC30F6012AT-20E/PF

DSPIC30F6012AT-20E/PF - 16-bit DSC, 144KB Flash, 20 MIPS | Microchip

The Microchip Technology DSPIC30F6012AT-20E/PF is a 16-bit Digital Signal Controller (DSC) from the dsPIC30F general-purpose family, operating at 20 MIPS with up to 40 MHz internal clock speed, housed in a 64-pin TQFP (14x14 mm) package with 0.8 mm lead pitch. It integrates a high-performance dsPIC DSC core with a built-in DSP engine, making it suitable for precision motor control, digital power conversion, and advanced sensor processing applications. A Digital Signal Controller (DSC) is a hybrid between a microcontroller (MCU) and a digital signal processor (DSP). It combines a deterministic single-cycle MCU core with DSP arithmetic capability, sitting in the product hierarchy as: DSC -> microcontroller -> embedded processor -> semiconductor. This category of device is engineered for closed-loop control loops that must execute MAC operations and PID calculations within microseconds, where a general-purpose MCU lacks DSP throughput and a standalone DSP lacks peripheral integration. The DSPIC30F6012AT-20E/PF delivers 144 KB of Flash program memory organized as 48K x 24 instruction words, alongside 8 KB of RAM for data. Its peripheral set includes CAN, I2C, SPI, and UART/USART communications interfaces, plus a 12-bit ADC, motor-control PWM, and up to 60 general-purpose I/O ports. The device operates from a 4.5 V to 5.5 V supply, drawing from internal Flash and supporting industrial temperature grades (-40 °C to +125 °C). Architecturally, the dsPIC30F core uses a modified Harvard architecture with separate program and data buses, enabling simultaneous instruction fetch and DSP operand access. The DSP engine adds a 40-bit barrel shifter, dual 40-bit accumulators, and single-cycle 16x16 MAC, allowing real-time FFT, FIR/IIR filtering, and power-factor-correction math without off-chip accelerators. The wide 24-bit instruction word accelerates complex control loop execution while preserving C-code compatibility with standard MPLAB X IDE toolchains. Typical applications include BLDC and AC induction motor drives, solar micro-inverters, industrial automation controllers, automotive body and chassis ECUs, uninterruptible power supplies (UPS), and switched-mode power supply (SMPS) digital control loops. The combination of DSP throughput, motor-control PWM, and CAN connectivity makes it well suited for field-oriented control (FOC) of three-phase motors. When designing with this device, verify supply decoupling at each AVDD/VDD pair and route the analog VREF+ separately from digital ground returns. Confirm that the FOSC/PLL configuration matches the application's MIPS budget before committing to layout. This page synthesizes distributor pricing, drop-in alternative listings, and practical design notes not collected on a single manufacturer page.

詢價 聯絡我們
DSPIC30F6012AT-20I/PT - 16-bit DSC, 144KB Flash, 20 MIPS | Microchip
DSPIC30F6012AT-20I/PT

DSPIC30F6012AT-20I/PT - 16-bit DSC, 144KB Flash, 20 MIPS | Microchip

The Microchip Technology DSPIC30F6012AT-20I/PT is a 16-bit Digital Signal Controller (DSC) from the dsPIC30F family, delivering 20 MIPS of processing performance, 144 KB of program Flash memory (organized 48K x 24), 8 KB of RAM, and 4 KB of EEPROM in a 64-pin TQFP (10x10 mm) surface-mount package. The "T" suffix denotes tape-and-reel packaging, "20" indicates 20 MIPS core speed, "I" indicates the -40C to +85C industrial temperature grade, and "/PT" specifies the 64-lead TQFP package. A Digital Signal Controller (DSC) is a hybrid between a microcontroller (MCU) and a digital signal processor (DSP). The dsPIC30F family specifically targets 5 V applications requiring both deterministic MCU control and DSP throughput, blending a modified Harvard architecture with a single-cycle MAC and 40-bit accumulators for high-performance motor control, audio, and sensor processing. Key features include a 16-bit modified Harvard architecture with DSP engine, 20 MIPS performance, 144 KB self-programmable Flash, 8 KB SRAM, 4 KB EEPROM, and a rich peripheral set: CAN, I2C, SPI, UART/USART, 12-bit ADC, motor-control PWM, input capture, and output compare. Integrated peripherals reduce external component count and BOM cost for embedded designs. The DSPIC30F6012AT-20I/PT is built on a 5 V CMOS process and operates from 2.5 V to 5.5 V, making it suitable for legacy 5 V industrial buses, automotive body and powertrain subsystems, and noise-prone motor-control environments. The 64-pin TQFP package with 10x10 mm footprint provides ample I/O for the device's eight 16-bit timers and 16-channel 12-bit ADC. Typical applications include BLDC and PMSM motor control (sensorless FOC), field-oriented control for industrial drives, automotive body controllers with CAN, audio processing front ends, UPS and inverter control loops, and industrial PLC digital signal preprocessing. The 4 KB EEPROM supports non-volatile parameter storage for field-calibrated systems. When designing with this device, verify that the 5 V supply tolerance matches your system rail. The DSP engine uses X and Y memory buses that must be configured correctly in linker files; consult dsPIC30F Family Reference Manual (DS70046). For new designs, Microchip recommends migrating to dsPIC33F or PIC24 families for higher performance and lower power. This page synthesizes distributor pricing, drop-in alternatives within the 64-pin TQFP package family, and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
DSPIC30F6012AT-30I/PF - 16-bit DSC, 144KB Flash, 64-TQFP | Microchip
DSPIC30F6012AT-30I/PF

DSPIC30F6012AT-30I/PF - 16-bit DSC, 144KB Flash, 64-TQFP | Microchip

The Microchip DSPIC30F6012AT-30I/PF is a 16-bit Digital Signal Controller (DSC) operating at 30 MIPS from a modified Harvard architecture core, packaged in a 64-pin TQFP (14x14 mm). It integrates 144 KB of Flash program memory (48K x 24), 8 KB of SRAM data memory, and 4 KB of EEPROM, combining microcontroller (MCU) control flow with DSP-class compute throughput for embedded motor-control and power-conversion systems. A Digital Signal Controller (DSC) is a hybrid class of microcontroller that fuses a deterministic MCU instruction set with a dedicated DSP engine (single-cycle multiply-accumulate, barrel shifter, zero-overhead loop buffers). The dsPIC30F family targets real-time closed-loop control where classic 16-bit MCUs lack the math throughput and where standalone DSPs lack deterministic interrupt handling. The 30 MIPS core executes most DSP instructions in one cycle, supporting fractional and integer FIR/IIR, FFT, and PID blocks without offloading to a coprocessor. Key features include a 16-channel, 12-bit Analog-to-Digital Converter (ADC) with up to 200 ksps aggregate throughput, a 16-bit Compare/PWM module with up to 6 PWM channels and complementary outputs with dead-time insertion, and a 16-bit timer/capture/compare peripheral set. Connectivity covers CAN 2.0B, I2C, SPI, and UART/USART. The industrial-grade -40C to +85C operating range and 4.5V to 5.5V supply simplify 5V-rail design. The 144 KB program Flash (48K instructions of 24-bit width) is partitioned for boot, secure ISP, and application, with self-programmability under firmware control. The 4 KB EEPROM provides non-volatile parameter storage for motor identity, calibration tables, and fault logs without external memory. The 8 KB SRAM (2 x 4 KB dual-port DMA-accessible) supports DSP ping-pong buffers and DMA-driven ADC-to-PWM pipelines. Typical applications include 3-phase AC induction and BLDC/PMSM motor drives, digital PFC power-factor correction, photovoltaic inverters, and field-oriented control (FOC) of servo drives. Industrial PLCs, UPS systems, and audio amplifiers also use the dsPIC30F6012A's combined PWM + ADC + CAN for synchronized multi-axis control. For power-rail design, place a 10 uF + 0.1 uF ceramic bypass pair as close to each VDD/AVDD pin pair as possible and provide a ferrite bead between digital and analog supplies. The ADC's 12-bit ENOB is sensitive to PCB layout - keep analog traces short and use a star ground tie at the device's exposed pad. Do not exceed the 5.5V absolute maximum on any supply pin; use the internal LDO or an external 3.3V rail for VDD if operating near the upper limit. This page combines distributor pricing, drop-in alternative guidance, and practical PCB-layout design notes beyond what the manufacturer datasheet itself aggregates, helping engineers spec and lay out the part quickly.

詢價 聯絡我們
DSPIC30F6012AT-30I/PT - 16-bit DSC 30MIPS 144KB Flash TQFP-64
DSPIC30F6012AT-30I/PT

DSPIC30F6012AT-30I/PT - 16-bit DSC 30MIPS 144KB Flash TQFP-64

The Microchip DSPIC30F6012AT-30I/PT is a 16-bit Digital Signal Controller (DSC) from the dsPIC30F family, integrating a high-performance DSP engine with a microcontroller on a single die. Housed in a 64-pin TQFP (10x10 mm) package with industrial -40C to +85C temperature rating, it delivers 30 MIPS performance from a modified Harvard architecture with single-cycle MAC operations. The device provides 144 KB of Flash program memory, 4 KB of data EEPROM, and 8 KB of SRAM, with 52 general-purpose I/O pins and a 12-bit ADC supporting up to 16 analog input channels. A Digital Signal Controller (DSC) is a class of microcontroller that fuses a traditional MCU instruction set with DSP-grade computational primitives, including single-cycle multiply-accumulate (MAC), barrel shifting, and dual-data-fetch capability. Within the broader taxonomy, a DSC sits between a microcontroller (MCU) and a full digital signal processor (DSP) - inheriting deterministic interrupt handling and rich peripherals from the MCU world while matching dedicated DSPs on per-cycle throughput for control-loop algorithms. The dsPIC30F family is purpose-built for closed-loop control applications requiring both signal processing and tight real-time response. Key differentiating features of the DSPIC30F6012A include: up to 2 PWM output pairs with 8 PWM channels for motor control and power conversion, a 16-channel 12-bit ADC with 200 ksps conversion rate, support for SPI, I2C, UART (2x), CAN, and parallel communication interfaces, plus a Motor Control PWM module with edge placement for PFC and FOC implementations. The 30 MIPS instruction throughput and dedicated DSP engine make it particularly suitable for digital motor control loops where instruction budget is constrained. The device operates from 2.5V to 5.5V VDD and is built on an enhanced flash process. Architectural highlights include 24-bit instruction width with 16-bit data path, a 31-level hardware stack, and DSP accumulator paths that bypass the general-purpose registers to deliver deterministic MAC latency. Code security is provided through configurable Flash and EEPROM protection bits. Typical applications span three-phase motor control (BLDC, PMSM), industrial automation controllers, uninterruptible power supplies (UPS), digital power conversion, audio processing, and sensor signal conditioning in industrial environments. The rich peripheral set directly targets motor-control firmware libraries that Microchip publishes free of charge. When laying out a PCB with this device, dedicate at least one solid ground plane and isolate analog VDD from digital VDD with a ferrite bead; the 12-bit ADC's absolute accuracy depends on supply noise well below 1 LSB. Program the configuration fuses carefully - incorrect oscillator settings here are a common production failure mode. This page synthesizes parametric data, current distributor pricing, drop-in alternatives within the dsPIC30F family, and PCB layout guidance not consolidated on any single manufacturer or distributor listing.

詢價 聯絡我們
DSPIC30F6013-20I/PF - 16-bit DSC, 132KB Flash, 80-TQFP | Microchip
DSPIC30F6013-20I/PF

DSPIC30F6013-20I/PF - 16-bit DSC, 132KB Flash, 80-TQFP | Microchip

The Microchip DSPIC30F6013-20I/PF is a 16-bit Digital Signal Controller (DSC) from the dsPIC30F family, integrating a high-performance DSP engine with a single-cycle 16-bit MCU core. Operating at up to 20 MIPS (Million Instructions Per Second) with an internal clock capable of reaching 40 MHz, the device delivers 132 KB of on-chip Flash program memory (44K x 24 words) and is housed in an 80-pin TQFP package measuring 14 x 14 mm. It is designed for real-time control applications that demand deterministic DSP performance combined with microcontroller simplicity. A Digital Signal Controller (DSC) is a hybrid architecture that merges a microcontroller's deterministic control loop with a Digital Signal Processor's multiply-accumulate (MAC) throughput. Within Microchip's taxonomy, the dsPIC30F belongs to the broader hierarchy: DSC -> MCU -> microcontroller -> embedded processor -> semiconductor. By integrating single-cycle MAC and barrel-shifter DSP instructions into a 16-bit RISC core, a DSC eliminates the need for a standalone DSP chip in motor-control, power-conversion, and audio-processing designs, reducing BOM cost, board area, and inter-IC latency. Key features of the DSPIC30F6013-20I/PF include 4 KB of RAM for data, a 12-bit Analog-to-Digital Converter (ADC) with multiple input channels, multiple 16-bit timers, and 60 digital I/O ports supporting peripheral pin select. Communication peripherals include UART, SPI, I2C, CAN, and I2S/SPIs interfaces, enabling flexible connectivity with sensors, actuators, and human-machine interfaces. The on-chip Flash supports self-programming for in-field firmware upgrades. The DSPIC30F6013-20I/PF operates from a single 4.5 V to 5.5 V supply, with an industrial temperature range of -40C to +85C denoted by the -20I/PF suffix (I = industrial, PF = 80-pin TQFP, lead-free). The architecture is based on a Harvard bus with separate program and data paths, allowing simultaneous instruction fetch and data access. The DSP engine supports fractional and integer arithmetic modes, with a saturation and rounding accumulator to prevent overflow in control loops. Typical applications include 3-phase AC induction and brushless DC motor control, uninterruptible power supplies (UPS) and power factor correction (PFC) converters, automotive sensor interfacing, audio decoding and equalization, industrial automation PLC, and digital power conversion. The CAN peripheral makes the part particularly attractive for vehicle body controllers and industrial field-bus nodes. When designing with this device, ensure that decoupling capacitors are placed close to VDD/VSS pairs, and that the analog supply rail (AVDD) is well-isolated from noisy digital switching currents. The Flash endurance rating should be checked against the in-field update frequency requirement; using the device's bootloader eliminates the need for external programming hardware. This page synthesizes distributor pricing, drop-in alternatives from the same dsPIC30F family, and practical design notes that extend beyond what is printed in the manufacturer datasheet.

詢價 聯絡我們
DSPIC30F6013-30I/PF - 30 MIPS 16-bit DSC 132KB Flash | Microchip | TQFP-80
DSPIC30F6013-30I/PF

DSPIC30F6013-30I/PF - 30 MIPS 16-bit DSC 132KB Flash | Microchip | TQFP-80

The Microchip DSPIC30F6013-30I/PF is a 16-bit Digital Signal Controller (DSC) that fuses a high-performance DSP engine with a single-cycle modified Harvard RISC MCU core, reaching 30 MIPS instruction throughput at up to 40 MHz in an 80-pin TQFP (PF) package. It integrates 132 KB of Flash program memory, 6 KB of RAM, and 2 KB of auxiliary Flash for EEPROM emulation, while supporting an external memory interface that can address up to 4 MB of program space and 64 KB of data space. In the broader product taxonomy, the dsPIC30 family sits between 8-bit PIC microcontrollers and 32-bit ARM Cortex devices: a DSC is a microcontroller (MCU) augmented by a multiply-accumulate (MAC) DSP engine, single-cycle hardware multiply, and 40-bit accumulators, which is why DSCs are frequently called "DSP-capable MCUs". They are categorized as microcontrollers > 16-bit microcontrollers > digital signal controllers > power management & signal processing ICs. The DSPIC30F6013 explicitly targets motor control, audio processing, and sensorless BLDC/PMSM applications where deterministic interrupt latency and DSP horsepower matter more than raw MHz. Key features include 8 channels of PWM with up to 16-bit resolution and three CPU-cycle PWM-to-PWM jitter, eight 16-bit timer/counters, two UART modules, two SPI ports, two I2C interfaces, a CAN 2.0B module, a 12-bit ADC with 16 channels at 200 ksps, a 16-channel 12-bit ADC supporting up to 200 ksps, and a 10-bit DAC output stage. The device supports 2.5 V to 5.5 V operation and offers both -40C to +125C industrial temperature range variants, packaged in TQFP-80. Typical applications span motor control (sensorless BLDC, AC induction, switched reluctance), uninterruptible power supplies, audio decoding, automotive sensor fusion, and industrial drives. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found on any single distributor page.

詢價 聯絡我們
DSPIC30F6013A-20E/PF - 16-bit DSC, 20MIPS, 132KB Flash, 80-TQFP
DSPIC30F6013A-20E/PF

DSPIC30F6013A-20E/PF - 16-bit DSC, 20MIPS, 132KB Flash, 80-TQFP

The Microchip Technology DSPIC30F6013A-20E/PF is a high-performance 16-bit Digital Signal Controller (DSC) combining MCU control with DSP throughput, delivering 20 MIPS at 40 MHz internal clock from a 4.5 V to 5.5 V supply. It integrates 132 KB (44K x 24) of on-chip Flash program memory, 6 KB RAM, and 1 KB EEPROM data memory, all packaged in an 80-pin TQFP (14x14 mm) with industrial-grade -40 C to +125 C operation and an enhanced (-E) temperature rating. A Digital Signal Controller (DSC) is a hybrid architecture that fuses the deterministic interrupt and peripheral set of a microcontroller with the multiply-accumulate (MAC) and single-cycle DSP engine of a DSP. Within the broader taxonomy, the dsPIC30F belongs to: 16-bit DSC -> 16-bit embedded controller -> microcontroller -> semiconductor. Its role in a system is to execute both control loops and real-time signal-processing algorithms (motor control, audio/voice, power conversion, sensor fusion) on a single chip, eliminating the MCU+DSP two-chip partitioning. Key features include a 16-bit wide data path with two 40-bit accumulators, single-cycle 16x16 MAC, barrel shifter, and zero-overhead looping, plus a CAN 2.0B module, two UARTs, two SPI ports, one I2C, an 8-channel 10-bit ADC at 1 Msps, and 60 general-purpose I/O pins. The 80-TQFP footprint gives 60 I/O - enough for multi-axis motor feedback, encoder interfaces, or TFT displays. The 'PF' suffix indicates 80-pin TQFP (14x14 mm) industrial-grade tray packaging. The architecture uses a modified Harvard bus with separate program and data paths, allowing instruction fetch concurrent with data access. DSP instructions execute in a single cycle, including MAC, ED/AC accumulation, and saturating arithmetic - ideal for digital filters, FFT stages, and closed-loop PID + observer code at audio-bandwidth sample rates. Typical applications include three-phase AC induction / BLDC / PMSM motor drives, sensorless motor control using space-vector PWM, digital audio processing (graphic and parametric EQ, surround), switched-mode power supply (SMPS) digital control loops, and industrial automation controllers requiring CAN connectivity. When designing with this device, allocate the 132 KB Flash carefully: bootloader + application + DSP libraries commonly consume 70-80 % of program memory. Use the dsPIC30F Family Reference Manual (DS70046) alongside the device datasheet for peripheral register-level details, and validate any DSP routine against the MAC saturation flags to prevent overflow errors. This page synthesizes distributor pricing, drop-in same-family alternatives from the dsPIC30F601xA series, and practical design guidance not found in the standalone datasheet - information tailored for engineers porting code between TQFP and PT variants or upgrading from older dsPIC30F6013 (non-A) silicon.

詢價 聯絡我們
DSPIC30F6013A-20E/PT - 16-bit 20 MIPS DSC, 132KB Flash, TQFP-80 | Microchip
DSPIC30F6013A-20E/PT

DSPIC30F6013A-20E/PT - 16-bit 20 MIPS DSC, 132KB Flash, TQFP-80 | Microchip

The Microchip Technology DSPIC30F6013A-20E/PT is a high-performance 16-bit Digital Signal Controller (DSC) that combines MCU control with DSP throughput, executing up to 20 MIPS at a 40 MHz oscillator and packaged in a 80-pin TQFP (12x12 mm). It integrates 132 KB (44K x 24) of on-chip Flash program memory and is targeted at 5V motor control and embedded signal-processing applications. A Digital Signal Controller (DSC) is a hybrid architecture that fuses a deterministic 16-bit microcontroller core with single-cycle MAC DSP engine, single-cycle hardware multiply, and 40-bit accumulators. DSCs sit in the product-type hierarchy between 8/16-bit microcontrollers (control-oriented) and 32-bit microprocessors (heavy compute); the dsPIC30F family specifically targets 5V systems where noise immunity, automotive sensor interfaces, and motor-drive PWM generation are required, complementing Microchip's higher-performance 3.3V dsPIC33F and PIC32MX lines. Key features include 132 KB Flash program memory, 6 KB SRAM, a 12-bit ADC with up to 16 input channels and 200 ksps throughput, multiple 16-bit timers, motor-control PWM modules with up to 8 output pairs, and a CAN 2.0B peripheral. The instruction set is 16-bit wide with an 83-base instruction set and 24-bit-wide program word, while 60 digital I/O pins give ample external interface flexibility. The extended (-40C to +125C) operating temperature rating and 4.5V-5.5V supply voltage support industrial environments. Peripherals also include UART, SPI, I2C, an enhanced CAN module, motor-control PWM with up to 8 channels and dedicated DSP outputs. The dsPIC30F6013A employs a Harvard architecture with separate program and data paths, a 40-bit barrel shifter, and DSP-specific accumulators that eliminate saturation under signal-processing workloads. The wide 5V-tolerant I/O structure simplifies interfacing to legacy analog stages and high-voltage gate drivers, and the rich motor-control PWM plus CAN peripherals make this device suitable for vector-controlled drives. Typical applications include three-phase AC induction and BLDC motor drives, sensor-less field-oriented control (FOC), UPS systems, solar inverters, audio signal processing, and industrial automation. The DSP engine handles Clarke/Park transforms and PID loops while the MCU core manages communication stacks. When designing with this part, place decoupling capacitors within 5 mm of every supply pin and keep the oscillator traces short. The 5V-wide VDD tolerance enables direct connection to industrial 24V-bus-derived rails (post-regulation) but demands attention to EMI from switching power stages adjacent to the DSC.

詢價 聯絡我們
DSPIC30F6013A-20I/PT - 20 MIPS 16-bit DSC 132KB Flash | Microchip
DSPIC30F6013A-20I/PT

DSPIC30F6013A-20I/PT - 20 MIPS 16-bit DSC 132KB Flash | Microchip

The Microchip Technology DSPIC30F6013A-20I/PT is a 20 MIPS 16-bit Digital Signal Controller (DSC) with 132KB (44K x 24) of Flash program memory, 6KB of RAM, and a 16-bit dsPIC core, housed in an 80-pin TQFP (12x12 mm) industrial-grade package. It operates from 2.5V to 5.5V and integrates CAN, I2C, SPI, and UART/USART peripherals, making it suitable for real-time control applications that require deterministic DSP throughput alongside microcontroller peripherals. A Digital Signal Controller (DSC) is a hybrid device that combines the control flexibility of a microcontroller with the computational throughput of a Digital Signal Processor (DSP). DSCs sit in the hierarchy: DSC -> microcontroller -> embedded processor -> semiconductor. The dsPIC30F family targets 5V applications where DSP precision is required, distinct from the dsPIC33F family which targets 3.3V operation at 40 MIPS. The dsPIC30F core executes most instructions in one clock cycle and includes a hardware MAC for 16x16-bit operations in a single cycle. Key features include 20 MIPS by default CPU performance, integrated 10-bit ADC, up to 8 PWM outputs, encoder interface, 5x16-bit timers, two UART, two SPI, one I2C, and one CAN module. The 132KB Flash supports self-programming via ICSP, enabling field firmware updates. The 6KB RAM allows substantial data buffering for DSP routines and protocol stacks. Typical applications include motor control (BLDC, PMSM, ACIM), power conversion (digital PFC, UPS, inverters), industrial automation (servo drives, CNC), automotive body and powertrain controllers, and audio processing. The CAN bus peripheral enables integration into automotive CAN networks, while the encoder interface simplifies closed-loop motion control without external hardware. When designing with this device, ensure that code protection bits are configured before deployment and that the ICSP pins are isolated from application circuitry to allow in-circuit programming. The TQFP-80 package requires a ground plane beneath for thermal management and EMI mitigation. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone. Source: Microchip datasheet family reference DS70143E and dsPIC30F Family Reference Manual DS70046.

詢價 聯絡我們
DSPIC30F6013A-30I/PF - 16-bit DSC 30MIPS 132KB Flash 80TQFP | Microchip
DSPIC30F6013A-30I/PF

DSPIC30F6013A-30I/PF - 16-bit DSC 30MIPS 132KB Flash 80TQFP | Microchip

The Microchip Technology DSPIC30F6013A-30I/PF is a 16-bit Digital Signal Controller (DSC) operating at 30 MIPS with 132 KB Flash program memory, housed in an 80-pin TQFP (14x14 mm) package. The device combines microcontroller (MCU) ease of use with digital signal processor (DSP) throughput, integrating 4 KB RAM, 2 KB data EEPROM, a 12-bit ADC with up to 16 channels, a 16-bit motor-control PWM module, and a wide range of communication peripherals including UART, SPI, I2C, and CAN. An explanation of the category: a Digital Signal Controller (DSC) sits at the intersection of a microcontroller and a DSP. While a standard MCU executes control logic with deterministic latency, a DSC such as the dsPIC30F adds single-cycle multiply-accumulate (MAC) hardware, dual-operand fetch, and a 40-bit accumulator, enabling real-time signal-processing tasks such as motor-control math (Clarke/Park transforms), power-line filtering (DFT/FFT), and audio codecs to run on the same chip alongside control firmware. In the broader taxonomy it sits as: DSC -> MCU/DSP hybrid -> embedded controller -> semiconductor IC. Key features include 30 MIPS performance at 4.5-5.5V operation (30 MIPS at 5V), an industrial-grade -40C to +125C operating range, on-chip Flash with self-programmability, and 16 Kbytes of instruction cache. The integrated ADC can perform 200 Ksps conversions, while the motor-control PWM supports complementary outputs with programmable dead time, making it well suited to three-phase variable-frequency drives. Architecturally, the dsPIC30F6013A uses a Harvard-style bus architecture with separate program and data paths, allowing sustained MAC throughput. The DSP engine features two 40-bit accumulators, two 16-bit working registers, and a barrel shifter. This deterministic DSP performance is preserved even during interrupt latency windows, which is critical for closed-loop control loops. Typical applications include three-phase motor control (BLDC, PMSM, AC induction), industrial inverters, switched-mode power supplies, sensorless fan/pump controllers, and Class-D audio amplifiers. The CAN interface makes it particularly suitable for automotive body and industrial networking applications. For designers, the key trade-off is Flash size: 132 KB restricts very large protocol stacks; if more memory is required, the dsPIC30F6014A doubles it to 144 KB in the same 80-pin TQFP. This page synthesises distributor pricing, drop-in same-package alternatives, and application guidance not collated in the manufacturer datasheet.

詢價 聯絡我們
DSPIC30F6013A-30I/PT - 30 MIPS 16-Bit DSC, 132KB Flash | Microchip
DSPIC30F6013A-30I/PT

DSPIC30F6013A-30I/PT - 30 MIPS 16-Bit DSC, 132KB Flash | Microchip

The Microchip DSPIC30F6013A-30I/PT is a high-performance 16-bit Digital Signal Controller (DSC) operating at 30 MIPS with 132 KB on-chip program memory, housed in an 80-pin TQFP (12x12 mm) industrial-temperature package. It integrates DSP compute capability with a modified Harvard RISC architecture, 4 KB SRAM, 8 KB data EEPROM, and a rich peripheral set including a 12-bit ADC, multiple UART/SPI/CAN modules, and dedicated motor-control PWM. A Digital Signal Controller (DSC) is a hybrid device that fuses a microcontroller's deterministic control peripherals with a Digital Signal Processor (DSP) engine capable of single-cycle MAC operations. The DSC category sits within the broader taxonomy of microcontrollers -> embedded controllers -> MCUs with DSP extensions, and is optimized for applications that require both closed-loop control (PWM, ADC) and high-speed numerical processing (FFT, FIR, encoder feedback) on a single chip. Key features include 132 KB of Flash program memory (44K x 24 organization), 30 MIPS execution from a 120 MHz internal clock, dual 40-bit accumulators, zero-overhead hardware DO and REPEAT loops, and 16 x 16-bit signed fractional multiplication in a single cycle. The 80-pin TQFP exposes up to 68 I/O lines, two UART modules, two SPI modules, two I2C modules, two CAN modules, an 8-channel motor-control PWM, a 16-channel 10-bit ADC, and a 12-bit ADC converter for high-resolution analog front-ends. Architecturally, the DSPIC30F6013A combines a 16-bit native datapath with DSP-engine MAC units and a barrel shifter, allowing efficient implementation of digital filters, motor-control algorithms (field-oriented control, space-vector modulation), and power-conversion control loops. The wide operating range of 4.5 V to 5.5 V (5 V nominal) and -40C to +85C industrial temperature grade make it suitable for harsh environments. Typical applications include three-phase AC induction and BLDC motor drives, switch-mode power supplies (SMPS), digital UPS systems, automotive body controllers, industrial automation and PLCs, and audio processing. The 132 KB code space and 30 MIPS throughput cover full-featured sensorless FOC and PFC firmware in a single device. A key design consideration is that the 5 V supply rail must be tightly decoupled with bulk + bypass capacitors, since ADC accuracy and PWM timing margins are sensitive to VDD ripple. Code protection fuse settings should be configured last in production to prevent bricking prototypes during development.

詢價 聯絡我們
DSPIC30F6013AT-20E/PF - 16-bit DSC 30MIPS 132KB Flash | Microchip
DSPIC30F6013AT-20E/PF

DSPIC30F6013AT-20E/PF - 16-bit DSC 30MIPS 132KB Flash | Microchip

The Microchip Technology DSPIC30F6013AT-20E/PF is a high-performance 16-bit Digital Signal Controller (DSC) that combines the control advantages of a microcontroller with the computational throughput of a DSP. The device operates at 20 MIPS (Million Instructions Per Second) from a 4.5V to 5.5V supply and integrates 132KB of Flash program memory, 6KB of SRAM data memory, and 2KB of EEPROM. It is delivered in an 80-pin TQFP (PF) package measuring 12x12 mm (or 14x14 mm per the manufacturer datasheet outline) with 60 digital I/O pins. A Digital Signal Controller is a hybrid architecture that merges a modified Harvard RISC CPU with dedicated DSP computational blocks. DSCs fill the architectural gap between traditional 8/16-bit microcontrollers (which lack real-time signal processing throughput) and standalone DSPs (which lack integrated peripherals for system control). The dsPIC30F family is designed for embedded motor control, power conversion, and audio processing applications where deterministic DSP performance is required alongside general-purpose control. Key features of the DSPIC30F6013AT-20E/PF include a 16 x 16-bit single-cycle hardware MAC (multiply-accumulate) engine, dual 40-bit accumulators, a 12-bit ADC with up to 16 channels, a 16-bit Motor Control PWM module with up to 8 outputs, encoder interface hardware, and a rich communication peripheral set: two CAN modules, two UART/USART, SPI, and I2C. The -20E speed grade specifies an extended operating temperature range of -40C to +125C. The architecture centers on a 16-bit dsPIC core built on a modified Harvard structure with separate 24-bit instruction and 16-bit data paths. DSP operations are handled by the integrated MAC engine with dual 40-bit accumulators, allowing sustained single-cycle 16x16 multiply operations. The deterministic interrupt structure and zero-overhead looping enable real-time DSP control loops typical of field-oriented motor control and digital power conversion. Typical applications include three-phase AC induction and BLDC motor drives (sensored and sensorless), uninterruptible power supplies (UPS), digital power-factor correction (PFC) converters, audio processing and effects units, and automotive sensor signal conditioning. The integrated CAN, encoder interface, and motor-control PWM simplify inverter-stage designs significantly. When designing with the DSPIC30F6013AT-20E/PF, ensure adequate decoupling on the analog AVLD rail serving the ADC, and follow the PCB layout recommendations for the motor-control PWM outputs to minimize switching noise coupling. The 'A' suffix denotes an enhanced analog front end (12-bit ADC) and the 'T' suffix denotes Tape & Reel packaging; '20E' denotes the 20 MIPS speed grade and extended temperature range. This page synthesizes distributor pricing, drop-in alternatives sourced from manufacturer cross-reference data, and practical design notes not aggregated on any single manufacturer page.

詢價 聯絡我們
DSPIC30F6013AT-20E/PT - 20 MIPS 16-bit DSC 132KB Flash TQFP-80
DSPIC30F6013AT-20E/PT

DSPIC30F6013AT-20E/PT - 20 MIPS 16-bit DSC 132KB Flash TQFP-80

The Microchip DSPIC30F6013AT-20E/PT is a high-performance 16-bit Digital Signal Controller (DSC) operating at 20 MIPS (40 MHz oscillator, with 4 MHz instruction cycle rate) and packaged in an 80-pin TQFP (12x12 mm). It integrates 132 KB of Flash program memory (44K x 24 words), 6 KB of RAM, and a 16-channel 12-bit Analog-to-Digital Converter for embedded signal processing and control. A Digital Signal Controller (DSC) is a hybrid architecture that combines the deterministic control advantages of a microcontroller (MCU) with the computational throughput of a Digital Signal Processor (DSP). The dsPIC30F family from Microchip occupies a specific point in the semiconductor taxonomy: MCU -> 16-bit MCU -> DSC -> dsPIC30F -> motor control / power conversion family. Engineers select DSCs over pure MCUs when the application requires high-speed math (Fast Fourier Transforms, digital control loops, encoder decoding) and over pure DSPs when deterministic interrupt latency and rich peripherals are required. Key features of the DSPIC30F6013AT-20E/PT include its dual-port RAM architecture, dedicated DSP engine with a 17-bit x 17-bit multiplier and 40-bit accumulator, a 12-bit ADC capable of 200 ksps conversion across 16 analog input channels, and extensive connectivity peripherals including CAN 2.0B, I2C, SPI, and UART/USART. The device also integrates five 16-bit timer/counters, an input capture module, an output compare/PWM module with up to 8 PWM channels, and brown-out plus power-on reset supervision. The integrated DSP engine can execute a single-cycle MAC (multiply-accumulate) operation in one instruction cycle, providing the throughput needed for closed-loop digital control. Architecturally, the DSPIC30F6013A family is built on a 5V-tolerant CMOS process with a modified Harvard architecture and 24-bit instruction width. The 'A' suffix denotes the second silicon revision, and the 'T' indicates tape-and-packaged delivery. The 80-pin TQFP package provides ample I/O (68 I/O pins) for systems integrating motor control, sensor fusion, and human-machine interface on a single device. Operating voltage spans 2.5V to 5.5V, supporting both 3.3V and 5V system designs. Typical applications include AC induction motor and brushless DC motor control, sensorless field-oriented control (FOC), power conversion (UPS, PFC, digital switching power supplies), industrial automation, automotive sensor processing, and embedded audio processing. The integrated CAN 2.0B peripheral and the 12-bit ADC with dual sample-and-hold make the part particularly suited for automotive body and chassis ECUs and industrial servo drives. When designing with the DSPIC30F6013AT-20E/PT, ensure the analog and digital supply pins (AVDD/AVSS and VDD/VSS) are properly decoupled with separate 10 uF and 100 nF capacitor pairs to achieve the ADC's published SNR performance. Program the configuration bits (FOSC, FWDT, FPOR) via the `#pragma config` directive in MPLAB X IDE before code generation to avoid unexpected oscillator or watchdog reset behavior. This page synthesizes distributor pricing, same-family and cross-family alternatives in the TQFP-80 footprint, and practical design notes that go beyond the bare manufacturer datasheet. Engineers comparing drop-in MCU alternatives or evaluating AEC-Q100 options can use the comparison_table below to make a procurement-grade decision.

詢價 聯絡我們
DSPIC30F6013AT-20I/PT - 16-bit DSC, 132KB Flash, 20 MIPS, 80-TQFP
DSPIC30F6013AT-20I/PT

DSPIC30F6013AT-20I/PT - 16-bit DSC, 132KB Flash, 20 MIPS, 80-TQFP

The Microchip Technology DSPIC30F6013AT-20I/PT is a 16-bit Digital Signal Controller (DSC) that integrates MCU peripherals with DSP capability, delivering up to 20 MIPS of processing performance in an 80-lead TQFP (12x12 mm) surface-mount package. It features 132 KB of Flash program memory (44K x 24) and 6 KB of RAM. A Digital Signal Controller (DSC) is a class of programmable logic device that combines the deterministic interrupt and peripheral architecture of a microcontroller (MCU) with the computational throughput of a digital signal processor (DSP). In the broader taxonomy, DSCs sit between general-purpose microcontrollers (PIC16, PIC32) and standalone DSPs, belonging to the embedded computing / microcontroller family of semiconductors. The dsPIC30F series was Microchip's first DSC family, designed specifically for 5 V operation in noisy industrial environments. Key features include a 16-bit modified Harvard architecture with native DSP support (single-cycle 16x16 multiply), on-chip 12-bit ADC with up to 16 channels, multiple communication peripherals (UART, SPI, I2C, CAN), 68 digital I/O pins, and a wide operating voltage range of 2.5 V to 5.5 V. The integrated DSP engine executes a 40-bit accumulator and supports fractional arithmetic, enabling real-time control loops and audio/sensor signal processing. Architecturally, the DSPIC30F6013A uses a 16-bit data path with a 24-bit instruction word and dual-bus Harvard topology for deterministic cycle counts. The -20I suffix indicates 20 MIPS maximum throughput at the industrial -40C to +85C operating range. The 'A' revision improves ADC performance and adds DMA support compared to the original dsPIC30F6013 silicon. The 'T' suffix designates tape-and-reel packaging. Typical applications include industrial motor control (BLDC, PMSM, ACIM drives), digital power conversion (SMPS, PFC), sensorless motor commutation, audio processing, automotive body electronics, and embedded control in noisy industrial environments where 5 V tolerance is required. When designing with this device, ensure adequate decoupling on AVDD/AVSS pairs to achieve specified ADC SNR; the DSP engine is C-programmable via MPLAB XC-DSC compilers, easing porting from pure-DSP or pure-MCU codebases. This page synthesizes distributor pricing, same-brand drop-in alternatives within the dsPIC30F6013A family, and practical design notes that supplement the manufacturer datasheet.

詢價 聯絡我們
DSPIC30F6013AT-30I/PF - 30 MIPS 16-bit DSP MCU 132KB Flash 80-TQFP | Microchip
DSPIC30F6013AT-30I/PF

DSPIC30F6013AT-30I/PF - 30 MIPS 16-bit DSP MCU 132KB Flash 80-TQFP | Microchip

The Microchip Technology DSPIC30F6013AT-30I/PF is a high-performance 16-bit Digital Signal Controller (DSC) combining a PIC MCU core with a DSP engine, delivering 30 MIPS at 30 MHz from a 4.5 V to 5.5 V supply, and packaged in an 80-pin TQFP (14x14 mm). It integrates 132 KB of Flash program memory (44K x 24) and is built on Microchip's dsPIC30F Harvard RISC core, giving the automotive sector a deterministic signal-processing platform. A Digital Signal Controller (DSC) is a hybrid class of microcontroller that fuses a traditional MCU control core with a single-cycle DSP MAC engine on a single die. In the device taxonomy, this places the DSPIC30F6013AT-30I/PF in the hierarchy: DSC -> DSP/MCU hybrid -> 16-bit microcontroller -> embedded MCU. This category is purpose-built for real-time closed-loop control and high-bandwidth signal processing, where general-purpose MCUs lack DSP throughput and stand-alone DSPs lack peripheral integration. Key features include 30 MIPS performance from a 30 MHz oscillator, a 12-bit ADC with up to 16 channels, two UART/SPI/I2C modules, two CAN modules, and two 16-bit timer/counters. The device also provides 60 digital I/O lines, PWM modules with dedicated time bases, and an on-chip Flash self-programming bootloader. The wide 4.5 V to 5.5 V supply range simplifies integration into 5 V analog signal chains. The DSP engine provides a single-cycle 16-bit x 16-bit MAC plus a 40-bit accumulator with dual operand fetch-back, enabling efficient FIR/IIR filtering, FFT butterfly computations, and closed-loop control loops. The modified Harvard architecture keeps program and data memory on separate buses, removing fetch bottlenecks that throttle von Neumann MCUs during DSP workloads. Typical applications include sensor-less BLDC/PMSM motor drives, automotive sensor fusion (with two CAN interfaces), industrial UPS and inverter control, and high-performance audio codecs with parametric equalization. The 80-pin TQFP and 5 V I/O make it well-suited for industrial PLC modules and motor-control inverter boards. When designing with this part, place 100 nF decoupling capacitors as close as possible to every VDD/VSS pair and ensure the MCLR reset circuit uses the recommended RC network. The 'I' suffix indicates the industrial -40 C to +85 C operating range and the 'A' denotes Flash revision 2 silicon; this 'T' tape-and-reel variant is the surface-mount packaging form of the original -30I/PF die. This page synthesizes distributor pricing, verified drop-in options, and practical design notes drawn from Microchip application notes - information not consolidated in the manufacturer datasheet alone.

詢價 聯絡我們
DSPIC30F6013T-30I/PF - 16-bit DSC, 132KB Flash, 30MIPs | Microchip
DSPIC30F6013T-30I/PF

DSPIC30F6013T-30I/PF - 16-bit DSC, 132KB Flash, 30MIPs | Microchip

The Microchip Technology DSPIC30F6013T-30I/PF is a 16-bit Digital Signal Controller (DSC) from the dsPIC30F family, integrating a high-performance DSP engine with a single-cycle MCU core. It delivers 30 MIPS of processing throughput at 30 MHz and includes 132 KB (44K x 24) of Flash program memory alongside 6 KB of RAM, packaged in an 80-pin TQFP (14x14 mm) surface-mount form factor. The part operates across the 2.5V-5.5V supply range and supports an industrial temperature grade of -40C to +85C. What is a Digital Signal Controller? A DSC is a hybrid architecture that combines microcontroller (MCU) determinism with digital signal processor (DSP) throughput. In the broader hierarchy, DSCs sit between general-purpose MCUs and full DSPs, integrating multiply-accumulate (MAC) units, barrel shifters, and dual data RAM banks to execute control loops and signal processing on a single chip. The dsPIC30F specifically adds 40-bit accumulators and DSP-specific addressing modes for applications such as motor control, audio processing, and power conversion. Key features of the DSPIC30F6013T-30I/PF include a 16-bit data path with modified Harvard architecture, 12-bit ADC with up to 16 channels, multiple communication peripherals (UART, SPI, I2C, CAN), PWM modules suitable for three-phase motor control, and a wide operating voltage range from 2.5V to 5.5V. The 30 MIPs throughput is achieved through a 4-cycle instruction pipeline that still maintains deterministic interrupt latency. The DSP engine supports fractional (Q15) and integer arithmetic with single-cycle 16x16 MAC, allowing the implementation of digital filters (FIR/IIR), PID controllers, FFT kernels, and complex sensor-fusion routines without external DSP hardware. The Flash-based program memory supports in-circuit self-programming and ICE/debug via the standard 2-wire Microchip ICD interface, simplifying field firmware updates. Typical applications include industrial motor drives (BLDC, PMSM, ACIM), automotive body controllers, digital power conversion (UPS, solar inverters), sensor signal conditioning, and low-cost audio effect processors. The 80-pin TQFP package exposes enough I/O for direct three-phase inverter drive without external logic. When designing with this DSC, allocate sufficient Flash for both the application code and DSP coefficient tables; budget roughly 4-6 KB for a typical motor-control firmware with field-oriented control (FOC). Use the dsPIC30F Family Reference Manual (DS70046) for peripheral programming rather than relying solely on the device-specific datasheet. This page synthesizes distributor stock signals, drop-in same-family variants, and application-level design guidance beyond the device datasheet, giving procurement and embedded engineers a faster path to BOM decisions and code bring-up.

詢價 聯絡我們
DSPIC30F6014-20E/PF - 16-bit DSC, 144KB Flash, 80-TQFP | Microchip
DSPIC30F6014-20E/PF

DSPIC30F6014-20E/PF - 16-bit DSC, 144KB Flash, 80-TQFP | Microchip

The Microchip Technology DSPIC30F6014-20E/PF is a 16-bit Digital Signal Controller (DSC) from the dsPIC30F family, integrating DSP engine and microcontroller functionality on a single die. It operates at 20 MIPS from a 4.5V to 5.5V supply, delivers 144KB (48K x 24) of on-chip Flash program memory, and is housed in an 80-pin TQFP (14x14 mm) package. The -20E speed grade variant supports industrial operating temperatures from -40°C to +125°C. A Digital Signal Controller (DSC) is a hybrid device that combines a microcontroller's deterministic control peripherals and interrupt response with a DSP's MAC-based computational throughput. Within the broader semiconductor hierarchy, a DSC sits between a microcontroller (MCU) and a digital signal processor (DSP), inheriting from both: an MCU-like instruction set and peripheral set, plus a DSP engine capable of single-cycle multiply-accumulate. The dsPIC30F family is Microchip's first-generation 16-bit DSC architecture, optimized for motor control, digital power conversion, and audio/speech processing. Key features include 8KB of RAM, 4KB of EEPROM, up to 60 digital I/O pins, multiple 16-bit timers, a 12-bit ADC with up to 16 channels, motor-control PWM modules, UART/SPI/I2C communication interfaces, and a 4-channel DMA controller. The integrated DSP engine delivers 20 MIPS sustained throughput for control loops and signal processing simultaneously. The architecture uses a Harvard-style bus with separate program and data paths, 24-bit instruction words, and a 16-bit data path. The DSP engine includes a 17x17-bit hardware multiplier and a 40-bit accumulator, enabling single-cycle MAC operations. Code-compatible peripherals and modular interrupt logic simplify firmware porting across the dsPIC30F family. Typical applications include motor control (BLDC, PMSM, ACIM), uninterruptible power supplies (UPS), digital power conversion, audio processing, and industrial automation. The wide peripheral set and DSP throughput make it well suited for real-time control loops with concurrent signal conditioning. When designing with this device, ensure the system clock configuration matches the 20 MIPS throughput requirement for time-critical DSP routines. Use the DMA controller to offload peripheral data movement, freeing CPU cycles for DSP kernels and reducing interrupt overhead. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
DSPIC30F6014-30I/PF - 16-Bit 30 MIPS DSC, 144KB Flash | Microchip
DSPIC30F6014-30I/PF

DSPIC30F6014-30I/PF - 16-Bit 30 MIPS DSC, 144KB Flash | Microchip

The Microchip Technology DSPIC30F6014-30I/PF is a 16-bit Digital Signal Controller (DSC) from the dsPIC30F family, combining DSP engine performance with microcontroller simplicity in an 80-pin TQFP (14x14 mm) package. Operating at 30 MIPS (40 MHz device clock) with 144 KB of on-chip Flash program memory and 8 KB of RAM, the part integrates a 17-bit x 17-bit hardware multiplier, two 40-bit accumulators with optional saturation logic, and a modified Harvard architecture for sustained DSP throughput. A DSC is a specialized microcontroller that merges a general-purpose MCU core with a dedicated DSP engine. It belongs to the broader hierarchy: DSC -> 16-bit microcontroller -> embedded processor -> semiconductor. Unlike a pure DSP, the dsPIC30F retains peripheral integration typical of an MCU (UART, SPI, I2C, ADC, timers), while the DSP engine enables single-cycle MAC operations, modulo addressing, and bit-reversed addressing needed for FFT and motor-control algorithms. This blend makes the family well-suited for closed-loop control and signal conditioning on a single chip. Key features of the DSPIC30F6014 include 144 KB Flash organized as 48K x 24 instruction words, 8 KB SRAM, 4 KB EEPROM, 60 I/O pins, and up to twelve 16-bit PWM outputs suitable for 3-phase motor and power-converter control. The 12-bit ADC provides up to 16 channels at 200 ksps, while communication interfaces include two UARTs, two SPI ports, and one I2C bus. The wide operating voltage range of 2.5 V to 5.5 V supports both 3.3 V and 5 V system designs. The DSP engine accelerates math-intensive control loops: the 17-bit x 17-bit single-cycle multiplier combined with two 40-bit saturating accumulators allows single-cycle MAC operations essential for PID controllers, FFT kernels, and digital filters. Modulo and bit-reversed addressing modes further reduce the overhead of FIR/IIR and FFT implementations. The architecture is C-compiler-optimized, allowing high-level development without sacrificing deterministic DSP performance. Typical applications include BLDC and PMSM motor control, sensorless field-oriented control (FOC) for fans and pumps, uninterruptible power supplies (UPS), power-factor-correction converters, and digital audio processing. Its 5 V tolerance and SMPS peripherals suit industrial motor drives where noise immunity is critical. When designing with this part, ensure decoupling capacitors are placed within a few millimeters of the VDD/VSS pairs and follow the 80-pin TQFP land pattern exactly. For drop-in replacements, see the alternatives section below - several dsPIC30F6014A and dsPIC30F6013A variants share the same 80-pin TQFP footprint. This page synthesizes distributor pricing, drop-in same-package alternatives, and design considerations not consolidated on the manufacturer product page.

詢價 聯絡我們
DSPIC30F6014A-20E/PF - 16-bit 20MIPS DSC, 144KB Flash | Microchip
DSPIC30F6014A-20E/PF

DSPIC30F6014A-20E/PF - 16-bit 20MIPS DSC, 144KB Flash | Microchip

The Microchip DSPIC30F6014A-20E/PF is a 16-bit Digital Signal Controller (DSC) from the dsPIC30F family, integrating a high-performance DSP engine with a 16-bit MCU architecture. The part delivers 20 MIPS of processing throughput at 20 MHz, packs 144 KB of on-chip Flash program memory (48K x 24), and ships in an 80-lead TQFP (14x14 mm) package. It is positioned as a general-purpose 16-bit DSC for embedded signal-processing applications. A Digital Signal Controller (DSC) is a hybrid class of microcontroller that combines a modified Harvard MCU architecture with single-cycle DSP MAC (multiply-accumulate) instructions. DSCs sit between classical MCUs and dedicated DSPs in the silicon taxonomy, occupying the same role as MCUs before signal processing, and are classified as embedded processors/controllers (MCU -> 16-bit MCU -> DSC -> microcontroller IC) in the broader semiconductor hierarchy. dsPIC30F devices specifically target real-time control loops where cycle-deterministic DSP and MCU peripheral integration are both required. Key features include 144 KB Flash, 8 KB SRAM, and 4 KB EEPROM for non-volatile data, plus dual 40-bit accumulators in the DSP engine. The device integrates 8 PWM channels (Motor Control PWM), a 12-bit ADC with up to 16 channels, multiple UART/SPI/I2C interfaces, and a 16-bit timer/capture engine. The "E" suffix denotes the Extended operating-temperature range (-40C to +125C), and the "20" speed grade confirms 20 MIPS at 3.3V operation. The "PF" suffix specifies the 80-pin TQFP package. Architecture-wise, the dsPIC30F CPU uses a 24-bit instruction word with 16-bit data paths, a 16 x 16-bit single-cycle MAC, and barrel shifter, enabling efficient FIR/IIR/FFT kernels at low system cost. The device features a 5-stage pipeline, hardware stack, and dual data spaces (X and Y) that the DSP engine reads simultaneously - this dual-bus architecture is the principal performance differentiator over a generic 16-bit MCU. Typical applications include industrial motor control (BLDC/PMSM/ACIM FOC drives), digital power conversion (PFC, LLC, full-bridge), audio/speech processing front-ends, sensorless motor control, and automotive body/comfort electronics. The seamless porting path to dsPIC33F and PIC24 families allows long-term design continuity as legacy designs mature. Design with this device at 3.0V to 3.6V VDD only; a stable LDO or buck-derived 3.3V rail is required. Place decoupling capacitors within 0.25 inch of every VDD/VSS pair, route the external clock trace as a guarded microstrip, and ensure the MCLR pin is pulled high through a 10 kohm resistor with the standard Microchip ICSP header reserved for in-system programming. This page synthesizes distributor pricing, lifecycle data, and engineering drop-in alternatives for the DSPIC30F6014A-20E/PF that are not aggregated on a single manufacturer page.

詢價 聯絡我們
DSPIC30F6014A-20I/PF - 20 MIPS 16-bit DSC, 144KB Flash, 80-TQFP | Microchip
DSPIC30F6014A-20I/PF

DSPIC30F6014A-20I/PF - 20 MIPS 16-bit DSC, 144KB Flash, 80-TQFP | Microchip

The Microchip Technology DSPIC30F6014A-20I/PF is a 16-bit Digital Signal Controller (DSC) from the dsPIC30F general-purpose family, rated for 20 MIPS operation and housed in an 80-pin TQFP (14x14 mm) package. It integrates 144 KB of program Flash, 8 KB of SRAM, and 4 KB of EEPROM, delivering the on-chip memory required for motor-control, audio-processing, and advanced sensor-fusion firmware. The part is industrial-grade (-40C to +85C) and supports seamless migration to dsPIC33F and PIC24 devices in similar footprints. A Digital Signal Controller is a hybrid MCU/DSP that combines deterministic microcontroller peripherals (timers, ADCs, communication ports) with a single-cycle MAC DSP engine. Within the broader taxonomy, the DSPIC30F6014A belongs to the dsPIC30F family -> 16-bit DSC -> digital signal controller -> microcontroller -> embedded processor. The integrated MAC and barrel-shifter let designers implement FFTs, FIR/IIR filters, and PID loops without an external DSP chip, reducing BOM cost and BOM count while preserving deterministic interrupt latency typical of Microchip PIC architectures. Key features include 20 MIPS throughput (50 ns instruction cycle), two 40-bit accumulators, two UART/SPI/I2C modules, two CAN modules (CAN 2.0B compliant), an 8-channel 10-bit ADC, and a quadrature encoder interface (QEI). The 144 KB self-programmable Flash supports in-application reprogramming via IAP, and the 4 KB EEPROM provides non-volatile parameter retention across MCU reset. Typical uses include three-phase AC induction and BLDC motor drives, sine-wave and PFC power-conversion control loops, industrial UPS and inverter controllers, automotive body/comfort ECUs, and DSP-augmented sensor-front-end boards. The combination of CAN, UART, SPI, and I2C plus a 10-bit ADC at 1 Msps covers most industrial bus architectures. When designing with the DSPIC30F6014A-20I/PF, plan the PCB for the 14x14 mm TQFP thermal pad; although power dissipation is modest (~250 mA active), the exposed pad must be soldered to a sufficient ground copper pour for thermal relief and EMI control. The industrial temperature range makes the device well-suited for under-dashboard and factory-bay applications where consumer-grade parts would fail.

詢價 聯絡我們
DSPIC30F6014A-20I/PT - 16-bit DSC, 144KB Flash, 80-TQFP
DSPIC30F6014A-20I/PT

DSPIC30F6014A-20I/PT - 16-bit DSC, 144KB Flash, 80-TQFP

The Microchip DSPIC30F6014A-20I/PT is a 16-bit Digital Signal Controller (DSC) in the dsPIC30F family, delivering 20 MIPS of processing performance from a modified Harvard RISC CPU with an integrated DSP engine. Housed in an 80-pin TQFP (12x12 mm) package, the device integrates 144 KB of Flash program memory, 8 KB of SRAM data memory, and 4 KB of EEPROM, supporting 3.3V and 5V operation across an industrial -40C to +85C temperature range. Connectivity includes CAN 2.0B, I2C, SPI, and UART/USART peripherals for embedded networking. A Digital Signal Controller is a hybrid class of microcontroller that combines a traditional MCU control-oriented architecture with DSP-grade arithmetic capability, including single-cycle 17x17-bit hardware multiplication, 40-bit accumulators, and dual operand fetch. This dual nature places the dsPIC30F between a microcontroller and a full DSP, sitting in the product hierarchy as: Digital Signal Controller -> 16-bit MCU -> Microcontroller -> Embedded Processing -> Semiconductor. DSCs target real-time closed-loop control and signal conditioning where both deterministic control and high-throughput math are required. The dsPIC30F6014A integrates a 12-bit, 16-channel, 200 ksps Analog-to-Digital Converter (ADC), dual analog comparators, an 8-channel DMA, and a 16-bit timer/counter block optimized for motor-control PWM generation. Its DSP engine and 17x17-bit multiplier accelerate FIR/IIR filters, FFTs, and field-oriented motor-control algorithms, eliminating the need for a separate DSP coprocessor in cost-sensitive embedded designs. Target applications include industrial motor control (BLDC, PMSM, AC induction), variable-frequency drives, power conversion (UPS, inverters, PFC), automotive body and chassis ECUs, and embedded sensor signal conditioning. The dual CAN 2.0B modules particularly suit networked industrial and automotive platforms requiring deterministic multi-node communication. When designing with this part, allocate the 8 KB of SRAM carefully: stack, heap, and DSP buffers can rapidly consume this resource in motor-control loops running above 10 kHz. The DSP engine operates on Q.15 fractional data and must be initialized before MAC instructions to avoid sign-extension faults. Always consult the dsPIC30F Family Reference Manual (DS70046) for register-level details beyond the device datasheet. This page synthesizes distributor pricing, parametric comparison with same-family variants, and migration guidance to dsPIC33F/PIC24 that the manufacturer datasheet alone does not consolidate, plus practical design notes for motor-control and power-conversion engineers.

詢價 聯絡我們
DSPIC30F6014A-30I/PF - 16-bit DSC, 30 MIPS, 144 KB Flash | Microchip
DSPIC30F6014A-30I/PF

DSPIC30F6014A-30I/PF - 16-bit DSC, 30 MIPS, 144 KB Flash | Microchip

The Microchip DSPIC30F6014A-30I/PF is a 16-bit Digital Signal Controller (DSC) from the dsPIC30F general-purpose family, delivering 30 MIPS of DSC performance in an 80-pin TQFP (14x14) package. It integrates a 24-bit instruction-word DSP engine with a 16-bit MCU core, 144 KB of on-chip Flash program memory, 8 KB of SRAM data memory, and 4 KB of EEPROM, and it operates from a 4.5 V to 5.5 V supply at industrial temperature range (-40C to +85C). A Digital Signal Controller is a hybrid class of microcontroller that combines a traditional MCU instruction set with a single-cycle DSP engine, a hardware MAC, and a barrel shifter. Compared with a pure microcontroller, a DSC executes FIR/IIR filters, FFTs, and PI/PID control loops in real time without software overhead. Compared with a standalone DSP, a DSC retains deterministic interrupt handling, on-chip peripherals, and ease of programming, making it a versatile compute node in motor control, power conversion, and sensor-fusion systems. The dsPIC30F family specifically targets 5 V industrial applications and is supported by the MPLAB XC16 toolchain and the dsPIC30F family reference manual DS70046. Key features of this variant include a 17x17-bit hardware multiplier, 40 MHz internal clock, dual CAN 2.0B modules, a 12-bit 200 ksps ADC with up to 16 analog input channels, motor-control PWM, quadrature encoder interfaces, and 68 digital I/O pins. The 30I suffix indicates the 30 MIPS speed grade and industrial temperature range; the PF suffix denotes the lead-free 80-pin TQFP package. Architecturally, the device combines a modified Harvard bus, 23-bit program counter, and a DSP engine with dual 40-bit accumulators. The wide instruction word enables single-cycle MAC operations, which accelerate digital filtering and control-law computations. The integration of CAN, motor-control PWM, and 12-bit ADC in a single 5 V silicon die removes the need for external DSP co-processors in cost-sensitive industrial designs. Typical applications include BLDC and AC induction motor control, sensorless field-oriented control (FOC), uninterruptible power supplies (UPS), photovoltaic inverters, digital audio processing, and industrial automation controllers. The 5 V tolerance and dual CAN interfaces also make it suitable for automotive body and chassis ECUs in non-safety-critical nodes. When designing with this part, allocate 4.5-5.5 V to AVDD/VDD with bulk decoupling close to the supply pins. Use the dsPIC30F Motor Control and SMPS libraries from Microchip for sensorless FOC and PFC reference firmware. Provide a stable 4x PLL-driven system clock and follow the TQFP-80 thermal pad layout to avoid hot spots at full 30 MIPS load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, supporting faster engineering decisions.

詢價 聯絡我們
DSPIC30F6014A-30I/PT - 30 MIPS 16-bit DSC, 144KB Flash, TQFP-80 | Microchip
DSPIC30F6014A-30I/PT

DSPIC30F6014A-30I/PT - 30 MIPS 16-bit DSC, 144KB Flash, TQFP-80 | Microchip

The Microchip DSPIC30F6014A-30I/PT is a 16-bit high-performance Digital Signal Controller (DSC) from the dsPIC30F family, delivering up to 30 MIPS at 40 MHz CPU clock and integrating 144 KB of on-chip Flash program memory in an 80-pin TQFP (12x12 mm) package. It combines DSP math throughput with a single-cycle MCU instruction set, dual 40-bit accumulators, and a single-cycle 17x17 hardware MAC, targeting embedded motor control, digital power, and high-speed sensing applications. A Digital Signal Controller is a hybrid architecture that merges a microcontroller's deterministic interrupt-driven control loop with a digital signal processor's parallel math engine, occupying the conceptual middle ground between MCU and DSP. Within the broader taxonomy, the dsPIC30F6014A sits at the IC tier, inside the Embedded Controllers branch, and is a sibling of the dsPIC33F and PIC24F device families that share peripheral IP and toolchain. It supports operation from 2.5 V to 5.5 V, enabling direct interface to 5 V analog front-ends without level shifters. Key features include 8 KB SRAM, 4 KB EEPROM, two UART/SPI/I2C modules, two CAN 2.0B controllers, eight 16-bit timers, a 12-bit ADC with up to 16 channels and 200 ksps throughput, plus a 16-bit PWM module with up to 8 outputs and complementary mode. The dedicated DSP engine features zero-overhead looping, bit-reverse addressing, and fractional/integer math support, allowing real-time FFT and FIR/IIR filter execution without starving the control loop. On the integration side, the device embeds an on-chip 8 MHz and 32 kHz RC oscillator, a 5-bit programmable dead-time controller, an input capture module, and a quadrature encoder interface, eliminating many external analog and timing components. The wide 2.5-5.5 V supply range combined with low standby current makes it suitable for both line-powered and battery-backed designs, while the integrated CAN bus and multiple serial interfaces reduce BOM in industrial and automotive networked systems. Typical applications include three-phase AC induction and BLDC/PMSM motor drives, solar micro-inverters and digital power factor correction, industrial sensor signal conditioning, UPS and switch-mode power supplies, and automotive body/comfort modules requiring on-chip CAN. Industrial designers favor this part for motion control; automotive engineers select it for CAN-connected actuator nodes. Educational users adopt it for control-theory and DSP lab courses. When designing with the DSPIC30F6014A, pay close attention to the 80-pin TQFP-12x12 (PT) footprint versus the larger 14x14 (PF) variant - both share the same silicon but differ in package body, which can affect PCB layout and clearance for high-voltage isolated designs. Use the MPLAB XC16 compiler and MPLAB X IDE for code development, and choose the motor-control or digital-power dsPIC30F peripheral libraries to shorten firmware bring-up. For new designs, evaluate migrating to the dsPIC33F or dsPIC33E family for higher MIPS and more peripherals while preserving peripheral-level code portability. This page synthesizes distributor pricing, same-package TQFP-80 drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - including cross-reference to the 14x14 TQFP (PF) variant and migration guidance to the dsPIC33E family.

詢價 聯絡我們